FEC30 FEC30 SERIES DC-DC CONVERTER 2:1 WIDE INPUT RANGE UP TO 30Watts FEATURES APPLICATIONS • NO MINIMUM LOAD REQUIRED • 1600VDC INPUT TO OUTPUT ISOLATION • STANDARD 2.00 X 1.60 X 0.40 INCH • SIX-SIDED CONTINUOUS SHIELD • UL60950-1, EN60950-1, & IEC60950-1 SAFETY APPROVALS • CE MARKED • COMPLIANT TO RoHS II & REACH 1600VDC ISOLATION REMOTE CONTROL UVP OCP • WIRELESS NETWORK • TELECOM/DATACOM • INDUSTRY CONTROL SYSTEM • DISTRIBUTED POWER ARCHITECTURES • SEMICONDUCTOR EQUIPMENT SCP OVP OTP TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25 Model Number FEC30-12S1P5 FEC30-12S1P8 FEC30-12S2P5 FEC30-12S3P3 FEC30-12S05 FEC30-12S12 FEC30-12S15 FEC30-12D12 FEC30-12D15 FEC30-24S1P5 FEC30-24S1P8 FEC30-24S2P5 FEC30-24S3P3 FEC30-24S05 FEC30-24S12 FEC30-24S15 FEC30-24D12 FEC30-24D15 FEC30-48S1P5 FEC30-48S1P8 FEC30-48S2P5 FEC30-48S3P3 FEC30-48S05 FEC30-48S12 FEC30-48S15 FEC30-48D12 FEC30-48D15 otherwise noted Input Range Output Voltage Output Current @Full Load Input Current @ No Load Efficiency Maximum Capacitor Load (1) VDC 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 VDC 1.5 1.8 2.5 3.3 5 12 15 ±12 ±15 1.5 1.8 2.5 3.3 5 12 15 ±12 ±15 1.5 1.8 2.5 3.3 5 12 15 ±12 ±15 A 6 6 6 6 6 2.5 2 ±1.25 ±1 6 6 6 6 6 2.5 2 ±1.25 ±1 6 6 6 6 6 2.5 2 ±1.25 ±1 mA 100 100 110 115 95 170 210 60 40 50 35 45 50 50 80 90 30 30 20 20 25 30 35 35 55 20 20 % 78 81 83 85 87 88 88 87 87 80 82 84 86 88 89 89 88 88 81 83 85 87 89 90 90 88 88 µF 85800 65000 33000 19500 10200 3240 1100 ±1020 ±675 85800 65000 33000 19500 10200 3300 1100 ±1020 ±675 85800 65000 33000 19500 10200 3300 1100 ±1020 ±675 PART NUMBER STRUCTURE FEC30 - 48 Series Name Input Voltage (VDC) 12: 9~18 24: 18~36 48: 36~75 S Output Quantity S: Single D: Dual 1 05 Output Voltage (VDC) 1P5: 1.5 1P8: 1.8 2P5: 2.5 3P3: 3.3 05: 5 12: 12 15: 15 12: ±12 15: ±15 - HS Assembly Option : No assembly HS: Heat-sink HC: Heat-sink with Clamp www.PDUKE.com 2015/2/26 FEC30 INPUT SPECIFICATIONS Parameter Conditions 12Vin(nom) 24Vin(nom) 48Vin(nom) Operating input voltage range Input reflected ripple current Start-up voltage Start up time Constant resistive load Input surge voltage 100 ms, max. DC-DC ON DC-DC OFF Input current of Ctrl pin Remote off input current Conditions Low Line to High Line at Full Load Load regulation No Load to Full Load Cross regulation Voltage adjustability Ripple and noise Asymmetrical load 25%/100% FL Measured by 20MHz bandwidth With a 0.1µF/50V MLCC Single Isolation voltage 1 minute Isolation resistance Isolation capacitance Switching frequency Safety approvals 500VDC VDC 8 16 33 25 25 -0.5 Others 12Vout, 15Vout All VDC ms 36 50 100 L-C type Open or 3 ~ 12VDC Short or 0 ~ 1.2VDC +0.5 2.5 Typ. -1.0 -0.2 -0.5 -0.5 -1.0 -5.0 -10 VDC mA mA Max. Unit +1.0 +0.2 +0.5 +0.5 +1.0 +5.0 +10 % 50 75 100 % % % % mVp-p +0.02 300 3.9 3.9 3.9 3.9 6.2 15 18 1.5Vout 1.8Vout 2.5Vout 3.3Vout 5Vout 12Vout 15Vout % of Iout rated mAp-p 9 17.8 36 -0.02 25% load step change Zener diode clamp GENERAL SPECIFICATIONS Parameter 2 VDC Min. Single Dual Single Dual Dual Dual Case material Base material Potting material Weight MTBF Unit 18 36 75 Positive logic Voltage accuracy Line regulation Over load protection Short circuit protection Max. 12 24 48 30 12Vin(nom) 24Vin(nom) 48Vin(nom) 12Vin(nom) 24Vin(nom) 48Vin(nom) Power up Remote ON/OFF 12Vin(nom) 24Vin(nom) 48Vin(nom) Referred to –Vin pin OUTPUT SPECIFICATIONS Parameter Temperature coefficient Transient response recovery time Over voltage protection Typ. 9 18 36 Nominal input and Full load Shutdown voltage Input filter Remote ON/OFF Min. %/ µs VDC 150 % Continuous, automatics recovery Conditions Input to Output Input(Output) to Case Min. 1600 1600 1 270 MIL-HDBK-217F, Full load www.PDUKE.com Typ. Max. Unit VDC GΩ pF 300 kHz UL60950-1 EN60950-1 IEC60950-1 Nickel-coated copper FR4 PCB Epoxy (UL94 V-0) 48g (1.69oz) 1.283 x 106 hrs 1000 330 2015/2/26 FEC30 ENVIRONMENTAL SPECIFICATIONS Parameter Operating ambient temperature Maximum case temperature Over temperature protection Storage temperature range Thermal impedance Conditions Min. With derating Typ. -40 Max. Unit +85 +100 +115 -55 Vertical direction by natural convection (20LFM) Without heat-sink With heat-sink +125 10 8.24 /W Thermal shock Vibration Relative humidity MIL-STD-810F MIL-STD-810F 5% to 95% RH EMC SPECIFICATIONS Parameter EMI (2) ESD Radiated immunity Fast transient (3) Surge (3) Conducted immunity Conditions EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Level Air ± 8kV and Contact ± 6kV 10 V/m ± 2kV ± 1kV 10 Vr.m.s Class A, Class B Perf. Criteria B Perf. Criteria A Perf. Criteria B Perf. Criteria B Perf. Criteria A Note: 1. 2. 3. Test by minimum input and constant resistive load. The standard modules meet EN55022 Class A and Class B with external components. For further information, please contact with P-DUKE. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor Power Mate suggest: Nippon chemi-con KY series, 220µF/100V. CAUTION: This power module is not internally fused. An input line fuse must always be used. CHARACTERISTIC CURVE 3 FEC30-48S05 Derating Curve FEC30-48S05 Derating Curve With Heat-sink FEC30-48S05 Efficiency vs. Input Voltage FEC30-48S05 Efficiency vs. Output Load www.PDUKE.com 2015/2/26 FEC30 MECHANICAL DRAWING PIN CONNECTION PIN 1 2 4 5 6 7 8 SINGLE +Vin -Vin Ctrl No pin +Vout -Vout Trim DUAL +Vin -Vin Ctrl +Vout Common -Vout Trim EXTERNAL OUTPUT TRIMMING Output can be externally trimmed by using the method shown below. ( ) for dual output trim. TRIM UP 7(7) TRIM DOWN 8(8) RU 8(8) RD 6(5) 1. All dimensions in inch (mm) 2. Tolerance :x.xx±0.02 (x.x±0.5) x.xxx±0.01 (x.xx±0.25) 3. Pin pitch tolerance ±0.01 (0.25) 4. Pin dimension tolerance ±0.004(0.1) 4 www.PDUKE.com 2015/2/26