ESD Suppressor

ESD Suppressor
ESD Suppressor
Type: EZAEG
EZAEG1N, 2N
Features
● Good
ESD withstanding (IEC61000-4-2 15 kV contact/air Discharge)
protection of high-speed data lines
● Low capacitance 0.04 pF : 0603(0201) size
0.05 pF : 1005(0402) size
● Good ESD suppression characteristics
● RoHS compliant
● ESD
Recommended Applications
● Smart
● ESD
phones, Mobile phones, RF Modules, NFC and GPS
suppresion of high-speed differential data line such as Antena circuit, HDMI, SATA, USB, Display Port
Explanation of Part Numbers
1
2
3
4
5
6
7
8
9
10
11
E
Z
A
E
G
2
N
5
0
A
X
Product Code
ESD Suppressor
Size
Code Size mm (inch)
1 0603 (0201)
2 1005 (0402)
Design Specification
Code Design Specification
N
ESD withstanding 15 kV
Rated Voltage 30 V
Peak Voltage
Code Peak Voltage
50
500 V
Special Feature
Code Special Feature
A Standard
Code
C
X
Construction
Packaging Methods
Packaging
Part No.
Pressed Carrier Taping
2 mm Pitch, 15,000 pcs. EZAEG1N
Pressed Carrier Taping
2 mm Pitch, 10,000 pcs. EZAEG2N
Dimensions in mm (not to scale)
L
Protective coating
a
Alumina substrate
Gap electrode
W
t
Electrode
(Between)
b
Part No.
(inch size)
ESD absorbent material
Electrode (Outer)
Dimensions (mm)
L
W
a
b
t
Mass (Weight)
[g/1000 pcs.]
EZAEG1N
0.60±0.03 0.30±0.03 0.15±0.10 0.15±0.10 0.23±0.03
(0201)
EZAEG2N
1.00±0.10 0.50±0.05 0.20±0.10 0.27±0.10 0.38±0.05
(0402)
0.12
0.60
Circuit Configuration
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02
Jul. 2014
ESD Suppressor
Ratings
Part Number
(inch size)
Capacitance(1)
Peak
Voltage(2)
Clamping
Voltage(3)
ESD
withstanding(4)
Rated
Voltage
Category Temperature
Range
EZAEG1N50AC (0201)
0.04+0.04
–0.03 pF
500 V max.
(350 V typ.)
100 V max.
Contact/Air
15 kV
30 V max
–55 to +125 °C
EZAEG2N50AX (0402)
+0.05
–0.04
0.05
pF
(1) Capacitance = The capacitance value shall be measured under the conditions specified below.
Frequency : 1 MHz±10 %, Voltage : 1 Vrms±0.2 Vrms, Temperature : 25 °C±2 °C
(2) Peak Voltage = The peak voltage value shall be measured under the following conditions. ESD test conditions : IEC61000-4-2, 8 kV contact discharge
(3) Clamping Voltage =The clamping voltage value shall be measured at 30 ns after initiation of pulse and measured under the conditions specified below.
ESD test conditions : IEC61000-4-2, 8 kV contact discharge
(4) ESD test conditions : IEC61000-4-2 contact discharge
ESD Suppression Voltage Waveform
5
400
0
350
-5
300
-10
Volts (V)
Attenuation (dB)
Frequency Characteristics
-15
250
200
150
100
-20
50
-25
-30
0
1
10
100
1000
Frequency(MHz)
-50
-20 0
10000
20 40 60 80 100 120 140 160 180 200
Times (nSecs)
Typical Circuits Requiring Protection
●
HDMI circuit
●
Antenna circuit
Antenna
HDMI Controller
HDMI
Rx/Tx
Ga/As-SW
or
ASM
Recommended Land Pattern
Recommended land pattern design for ESD Suppressor is shown below.
c
ESD Suppressor
Part Number
(inch size)
EZAEG1N
(0201)
EZAEG2N
(0402)
a
Dimensions (mm)
b
c
0.3 to 0.4
0.8 to 0.9
0.25 to 0.35
0.5 to 0.6
1.4 to 1.6
0.40 to 0.60
a
b
■ As for Packaging Methods, Soldering Conditions and Safety Precautions,
Please see Data Files
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
02
Jul. 2014