This component is RoHS compliant OPI 2000M High Speed Opto Isolator Surface Mount ATEX and IECEx certified Pb The OPI 2000M High Speed Optically Coupled Isolator consists of a High Speed Infrared emitter coupled to a silicon photo I.C. The unit is designed for applications requiring high voltage isolation between input & output. • Surface Mount in Tape & Reel High Speed 2Mb/sec. • 10KV isolation Low Propagation Delay CERTIFICATE ATEX BAS01ATEX1285U/3 CERTIFICATE IECEx BAS 06.0021U/1 Designed and manufactured to:IEC 60079-0: 2000 Edition 3.1 IEC 60079-11 :1999 Edition 4 IEC 60097-26 :2004 Edition 1 Conditions of use apply:- See ‘Schedule of limitations’ on certificate. Confirmed conform to:EN60079-0:2006 EN61241-0:2006 EN60079-11:2007 EN61241-11:2006 EN60079-26:2004 Conditions of use apply:- See ‘Schedule of limitations’ on certificate 14.45-0.0+0.2 MECHANICAL DATA 6.65 9.25 SURFACE MOUNT LEAD FORM CONDITIONS OF USE APPLY +0.2 0 Emitter 0.4x0.45 6.5 1.75 0.4 10.50-0.0+0.2 SENSOR 0.5 SQ 0.5 2.54 1.91 1.91 GRD K PIN OUT (TOP VIEW) Vout Vcc BEDFORD OPTO TECHNOLOGY LTD 1,BIGGAR BUSINESS PARK, BIGGAR,LANARKSHIRE, ML12 6FX Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 Website: bot.co.uk E-mail: [email protected] ISS J 21.07.08 An 1/5 OPI2000M ABSOLUTE MAXIMUM RATINGS (25OC unless otherwise noted) INPUT DIODE FORWARD DC CURRENT REVERSE DC VOLTAGE POWER DISSIPATION 100mA 5 Volts 150mW (ii) OUTPUT IC MAX SUPPLY VOLTAGE POWER DISSIPATION 7 Volts 165mW OPERATING TEMP -40OC TO +80OC STORAGE TEMP -40OC TO +85OC + 10KV DC (i) INPUT-TO-OUTPUT ISOLATION VOLTAGE i) ii) Measured with the input leads and output leads shorted together for one min. Thermal resistance 450 K/W Whilst the devices are capable of operating continually at the noted elevated temperatures users should be aware of the possibility of the need to increase the diode current to trigger the device over long periods at high temperatures & currents. CIRCUIT This component is RoHS compliant Vgen Rf Pb GND + + RL =560 ohm RL Vout C Vcc C=0.01uF Packing BEDFORD OPTO TECHNOLOGY LTD 1,BIGGAR BUSINESS PARK, BIGGAR,LANARKSHIRE, ML12 6FX Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 Website: bot.co.uk E-mail: [email protected] ISS J 21.07.08 Waffle Trays - 100 per tray 290mm x 200mm. Tape & Reel - 300 Devices per 13” Diam Reel with 7” Hub 24mm Wide tape. 2/5 OPI 2000M This component is RoHS compliant Pb BEDFORD OPTO TECHNOLOGY LTD 1,BIGGAR BUSINESS PARK, BIGGAR,LANARKSHIRE, ML12 6FX Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 Website: bot.co.uk E-mail: [email protected] ISS J 21.07.08 ADVISED SOLDERING CONDITIONS 3/5 OPI 2000M This component is RoHS compliant OPTO ELECTRONIC DATA (TA = 25OC) PARAMETER Pb SYMBOL MIN TYP MAX UNITS TEST CONDITIONS Forward Voltage VF - 1.35 1.6 V If=100mA tp=20mS Reverse Voltage VR 5.0 - - V Ir = 100uA INPUT DIODE OUTPUT IC ( Vcc=4.75 to 5.25 ) High level Output Current ICH - 100 uA Ic = 10 uA Low Level Output Voltage VOL - 0.6 V IF=10mA IOL=2.6mA High Level Supply Current ICCH 15 mA IF=0 Low Level Supply Current ICCL 18 mA IF=7.5mA COUPLED(Vcc=5volts) tPLH 800 nSecs RL=560ohms C=0.01uF Propagation Delay to High Output Level tPHL 800 nSecs ditto Input/Output Isolation Voltage Vi-o Volts Input and output leads shorted 10kV BEDFORD OPTO TECHNOLOGY LTD 1,BIGGAR BUSINESS PARK, BIGGAR LANARKSHIRE, ML12 6FX Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 Website: bot.co.uk E-mail: [email protected] ISS J 21.07.08 Propagation Delay to Low Output level 4/5 OPI 2000M CONFORMITY STATEMENT OPI2000M SERIES This component is RoHS compliant Pb Manufacturer:- BEDFORD OPTO TECHNOLOGY LTD Address:1 Biggar Business Park, Market Road, Biggar, Lanarkshire, ML12 6FX, Scotland Directive 94/9/EC EC-Type Examination Certificate:BAS01ATEX1285U – Latest supplement BAS01ATEX1285U/3 issued 30.10.07 Provisions of the Directive fulfilled by the component:GroupII Category 1GD EexiaIIC Notified Body for EC-Type Examination & Production:- BaseefaLtd. – No. 1180 Baseefa Ltd. Rockhead Business Park, Staden Lane, Tel:- +44 (0)1298 766600 Buxton, Fax:- +44 (0)1298 766601 Derbyshire SK17 9RZ, e-mail:- [email protected] England Harmonised Standards used:EN60079-0:2006 EN60079-11:2007 EN61241-11:2006 Other Standards used:EN60079-26:2004 – (confirmed by Notified Body unit complies in all respects) EN61241-0:2006 – (State of the Art – intended for harmonisation) _________________________________ Mr R.W.Stott Managing Director ISS J 21.07.08 On Behalf of Bedford Opto Technology Ltd., I declare that, the date the component accompanied by this statement is placed on the market, the component conforms with all technical and regulatory rerquirements of the ATEX Directive 94/9/EC. 5/5