ESD Suppressor ESD Suppressor Type: EZAEG EZAEG2A, 3A Features ● ESD protection of ● Low capacitance high-speed data lines 0.04 pF : 0603(0201) size 0.05 pF : 1005(0402) size ● Good ESD suppression characteristics ● Good ESD withstanding ● RoHS compliant Recommended Applications ● Smart ● ESD phones, Mobile phones, RF Modules, NFC and GPS suppresion of high-speed differential data line such as Antena circuit, HDMI, SATA, USB, Display Port Explanation of Part Numbers 1 2 3 4 5 6 7 8 9 10 11 E Z A E G 2 A 5 0 A X Product Code ESD Suppressor Size Code Size mm (inch) 2 1005 (0402) 3 1608 (0603) Design Specification Code Design Specification A Rated Voltage 30 V Peak Voltage Code Peak Voltage 50 500 V Special Feature Code Special Feature A Standard Code X V Construction Packaging Methods Packaging Part No. Pressed Carrier Taping 2 mm Pitch, 10,000 pcs. EZAEG2A Punched Carrier Taping 4 mm Pitch, 5,000 pcs. EZAEG3A Dimensions in mm (not to scale) L a Protective coating Alumina substrate W Gap electrode t b Electrode (Between) Part No. (inch size) ESD absorbent material Electrode (Outer) Dimensions (mm) L W a b t Mass (Weight) [g/1000 pcs.] EZAEG2A 1.00±0.10 0.50±0.05 0.20±0.10 0.25±0.10 0.38±0.05 (0402) EZAEG3A 1.60±0.15 0.80±0.15 0.30±0.20 0.30±0.20 0.50±0.10 (0603) 0.6 2.2 Circuit Configuration Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 02 Jul. 2014 ESD Suppressor Ratings Part Number (inch size) Capacitance(1) Peak Voltage(2) Clamping Voltage(3) Rated Voltage Category Temperature Range EZAEG2A50AX (0402) 0.05+0.05 –0.04 pF EZAEG3A50AV (0603) 0.10+0.10 –0.08 pF 500 V max. (350 V typ.) 100 V max. 30 V max –55 to +125 °C (1) Capacitance = The capacitance value shall be measured under the conditions specified below. Frequency : 1 MHz±10 %, Voltage : 1 Vrms±0.2 Vrms, Temperature : 25 °C±2 °C (2) Peak Voltage = The peak voltage value shall be measured under the following conditions. ESD test conditions : IEC61000-4-2, 8 kV contact discharge (3) Clamping Voltage = The clamping voltage value shall be measured at 30 ns after initiation of pulse and measured under the conditions specified below. ESD test conditions : IEC61000-4-2, 8 kV contact discharge ESD Suppression Voltage Waveform 5 400 0 350 -5 300 -10 Volts (V) Attenuation (dB) Frequency Characteristics -15 250 200 150 100 -20 50 -25 -30 0 1 10 100 1000 Frequency(MHz) -50 -20 0 10000 20 40 60 80 100 120 140 160 180 200 Times (nSecs) Typical Circuits Requiring Protection ● HDMI circuit ● Antenna circuit Antenna HDMI Controller HDMI Rx/Tx Ga/As-SW or ASM Recommended Land Pattern Recommended land pattern design for ESD Suppressor is shown below. c ESD Suppressor Part Number (inch size) EZAEG2A (0402) EZAEG3A (0603) a Dimensions (mm) b c 0.5 to 0.6 1.4 to 1.6 0.4 to 0.6 0.7 to 0.9 2.0 to 2.2 0.8 to 1.0 a b ■ As for Packaging Methods, Soldering Conditions and Safety Precautions, Please see Data Files Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 02 Jul. 2014