This component is RoHS compliant OPI 2000M High Speed Opto Isolator Surface Mount ATEX and IECEx CERTIFIED Pb The OPI 2000M High Speed Optically Coupled Isolator consists of a High Speed Infrared emitter coupled to a silicon photo I.C. The unit is designed for applications requiring high voltage isolation between input & output. x Surface Mount in Tape & Reel High Speed 2Mb/sec. x 10KV isolation Low Propagation Delay CERTIFICATE ATEX BAS01ATEX1285U/4 CERTIFICATE IECEx BAS 06.0021U/3 Confirmed conform to:IEC 60079-0:2007 Edition 5 IEC 60079-11:2006 Edition 5 IEC 60079-26:2006 Edition 2 IEC 61421-0:2004 Edition 1 IEC 61241-11:2005 Edition 1 Conditions of use apply:- See Schedule of limitations on certificate / details repeated on Page 4 this datasheet Confirmed conform to:EN60079-0:2009 EN61241-0:2006 EN60079-11:2007 EN61241-11:2006 EN60079-26:2007 Conditions of use apply:- See ‘Schedule of limitations’ on certificate / details repeated on Page 4 this datasheet MECHANICAL DATA 14.45-0.0+0.2 6.65 9.25 SURFACE MOUNT LEAD FORM CONDITIONS OF USE APPLY +0.2 0 Emitter 0.4x0.45 6.5 1.75 0.4 10.50-0.0+0.2 SENSOR 0.5 SQ 0.5 2.54 1.91 1.91 GRD K PIN OUT (TOP VIEW) Vout Vcc BEDFORD OPTO TECHNOLOGY LTD 1,BIGGAR BUSINESS PARK, BIGGAR,LANARKSHIRE, ML12 6FX Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 Website: bot.co.uk E-mail: [email protected] Iss L 24.04.12 An 1/5 OPI2000M ABSOLUTE MAXIMUM RATINGS (25OC unless otherwise noted) INPUT DIODE FORWARD DC CURRENT REVERSE DC VOLTAGE POWER DISSIPATION 100mA 5 Volts 150mW (ii) OUTPUT IC MAX SUPPLY VOLTAGE POWER DISSIPATION 7 Volts 165mW OPERATING TEMP -40OC TO +80OC STORAGE TEMP -40OC TO +80OC + 10KV DC (i) INPUT-TO-OUTPUT ISOLATION VOLTAGE i) ii) Measured with the input leads and output leads shorted together for one min. Thermal resistance 450 K/W Whilst the devices are capable of operating continually at the noted elevated temperatures users should be aware of the possibility of the need to increase the diode current to trigger the device over long periods at high temperatures & currents. CIRCUIT This component is RoHS compliant Vgen Rf Pb GND + + RL =560 ohm RL Vout C Vcc C=0.01uF Packing BEDFORD OPTO TECHNOLOGY LTD 1,BIGGAR BUSINESS PARK, BIGGAR,LANARKSHIRE, ML12 6FX Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 Website: bot.co.uk E-mail: [email protected] Iss L 24.04.12 Waffle Trays - 100 per tray 290mm x 200mm. Tape & Reel - 300 Devices per 13” Diam Reel with 7” Hub 24mm Wide tape. 2/5 OPI 2000M This component is RoHS compliant Pb BEDFORD OPTO TECHNOLOGY LTD 1,BIGGAR BUSINESS PARK, BIGGAR,LANARKSHIRE, ML12 6FX Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 Website: bot.co.uk E-mail: [email protected] Iss L 24.04.12 ADVISED SOLDERING CONDITIONS 3/5 OPI 2000M This component is RoHS compliant OPTO ELECTRONIC DATA (TA = 25OC) PARAMETER Pb SYMBOL MIN TYP MAX UNITS TEST CONDITIONS Forward Voltage VF - 1.35 1.6 V If=100mA tp=20mS Reverse Voltage VR 5.0 - - V Ir = 100uA INPUT DIODE OUTPUT IC ( Vcc=4.75 to 5.25 ) High level Output Current ICH - 100 uA Ic = 10 uA Low Level Output Voltage VOL - 0.6 V IF=10mA IOL=2.6mA High Level Supply Current ICCH 15 mA IF=0 Low Level Supply Current ICCL 18 mA IF=7.5mA COUPLED(Vcc=5volts) Propagation Delay to Low Output level tPLH 800 nSecs RL=560ohms C=0.01uF Propagation Delay to High Output Level tPHL 800 nSecs ditto Input/Output Isolation Voltage Vi-o Volts Input and output leads shorted 10kV SCHEDULE OF LIMITATIONS EC-Type Examination Certificate BAS01ATEX1285U Schedule of Limitations:- 17th August 2001 1– The Opto-isolator must be mounted on a p.c.b. having a CTI of at least 175 so that creepage and clearance distances are not impaired. The surface mounted device is designed for the pins to be soldered to pads on the same side of the printed circuit board as the component and must only be used either:a) on printed circuit boards that are potted, provided that the pad segregation maintains at least 2mm under potting. OR b) on printed circuit boards which are coated provided that the pad segragationmaintains at least 3.3mm under coating. Wherte the coating shall seal the connections after soldering and shall be two coats if applied by spraying or a single coat if dipped, brushed or vacuum impregnated. A CTI of at least 175 shall apply to both the pcb substrate and the coating material. 2– The Opto-isolator may be used to provide isolation between either:i) A non-intrinsically safe circuit and an intrinsically safe circuit (non IS : IS), where the IS circuit voltage is not greater than 75 Volts peak or d.c. ii) Two intrinsically safe circuits (IS : IS), where the sum of the two circuit voltages is not greater than 375 Volts peak or d.c. 3– The Opto-isolator must be installed such that the connection pins are provided with a degree of protection IP20 where gasses and vapours may be present. If the Opto-isolator is to be installed within apparatus where flammable dusts represent a hazard then the overall apparatus must be appropriately certified, (e.g. EN 50281-1-1). Supplementary EC-Type Examination Certificate BAS01ATEX1285U/3 Schedule of Limitations:- 30th October 2007 For all future applications of the High Speed Opto-Isolator types OPI2000M and OPI2000MTH the Schedule of Limitations No 3 is modified to take account of the more restrictive requirements of the Standards where DUST forms the hazard. The Opto-isolator types OPI2000M and OPI2000MTH must be installed such that the connection pins are provided with a degree of protection of at least IP20 where gasses and vapours may be present. If the Opto –isolators are to be installed where DUSTS represent a hazard, then they must be provided with a degree of protection of at least IP54 and the overall apparatus must be appropriately certified to DUST Standards, EN 61241-0:2006 and EN 61241-11:2006. Certificate No:- IECEx BAS 06.0021U Schedule of Limitations:- Date of Issue:- 2001-12-13 Issue No.:- 3 1– When used in intrinsically safe apparatus it will be necessary to determine a surface temperature classification for the Opto-Isolator ( OPI2000M—Thermal resistivity ºC/W is 87) 2– The Opto-Isolator must be mounted on a printed circuit board such that creepage and clearance distances are not impaired. 3- The Opto-isolator must be installed such that the connection pins are provided with a degree of protection IP20 where gasses and vapours may be present. If the Opto-isolator is to be installed within apparatus where flammable dusts represent the hazard then they must be provided with a degree of protection of IP54 and the apparatus must be appropriately certified for DUST hazards. 4– Surface-Mount OPI2000M only and in addition to above:- The surface mount OPI2000M must only be used on a printed circuit boardthat is either:- a) potted, providing the pad segregation remains at least 2mm under the potting. OR b) conformally coated, providing the pad segregation remains at least 3.3mm under the coating. The conformal coating must have a CTI in excess of 175. BEDFORD OPTO TECHNOLOGY LTD 1,BIGGAR BUSINESS PARK, BIGGAR LANARKSHIRE, ML12 6FX Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 4/5 Iss L 24.04.12 OPI 2000M CONFORMITY STATEMENT OPI2000M This component is RoHS compliant Pb Manufacturer:- BEDFORD OPTO TECHNOLOGY LTD Address:1 Biggar Business Park, Market Road, Biggar, Lanarkshire, ML12 6FX, Scotland Directive 94/9/EC EC-Type Examination Certificate:BAS01ATEX1285U – Latest supplement BAS01ATEX1285U/4 issued Dec. 2011 Provisions of the Directive fulfilled by the component:Ex ia IIC Ga (-40°C Ta +80°C) II 1 GD Ex ia IIIC Da (-40°C Ta +80°C) Notified Body for EC-Type Examination & Production:- BASEEFA Ltd. – No.1180 BASEEFA Ltd. Rockhead Business Park, Staden Lane, Tel:- +44 (0)1298 766600 Buxton, Fax:- +44 (0)1298 766601 Derbyshire SK17 9RZ, e-mail:- [email protected] England Harmonised Standards used:EN60079-0:2009 EN61241-0:2006 EN60079-11:2007 EN61241-11:2006 EN60079-26:2007 Other Standards used:- _________________________________ Mr R.W.Stott Managing Director PP- Iss L 24.04.12 On Behalf of Bedford Opto Technology Ltd., I declare that, the date the component accompanied by this statement is placed on the market, the component conforms with all technical and regulatory rerquirements of the ATEX Directive 94/9/EC. 5/5