Wide View/Long Travel LCD 64 x 32 Pushbutton SmartSwitch TM DISTINCTIVE CHARACTERISTICS • Same outer dimensions of switch and footprint, enabling ease of replacement with current switches • Programmable display graphics for alphanumeric characters and animated sequences • 64 colors of backlighting can be controlled dynamically • Pushbutton switch with LCD, RGB LED backlighting • General brightness of backlight is dynamically controlled in eight steps from dark to bright • Operated by commands and data supplied via serial communications (SPI) • Incorporates bitmap display function • Dual image VRAM for quick change of displayed images • Travel distance of 4.5mm (same as KP01 Series) • Low energy consumption • Dust tight construction Viewing area: 17.0mm x 13.0mm (horizontal x vertical) High reliability and long life of three million actuations High resolution of 64 x 32 pixels Epoxy sealed straight PC terminals Snap-in standoff legs ensure secure mounting and alignment, and prevents dislodging during wave soldering. Actual Size ATTENTION PART NUMBER & DESCRIPTION ELECTROSTATIC SENSITIVE DEVICES Part Number Switch Description LCD Mode LED Color IS15EBFP4RGB SPST Momentary ON Gold Contacts Straight PC Terminals Black & White FSTN Positive Red/Green/Blue 4.1.15 www.nkk.com 1 SmartSwitch TM Wide View/Long Travel LCD 64 x 32 Pushbutton IS15EBFP4RGB RGB LED Backlight Black and White LCD Long Travel SWITCH SPECIFICATIONS Circuit SPST normally open Electrical Capacity (Resistive Load) 100mA @ 12V DC Contact Resistance 200 milliohms maximum @ 20mV 10mA Insulation Resistance 100 megohms minimum @ 100V DC Dielectric Strength 125V AC for 1 minute minimum Mechanical Endurance 3,000,000 operations minimum Electrical Endurance 3,000,000 operations minimum Operating Force 2.0 ± 0.5 Newtons Total Travel 4.5mm (.177”) TYPICAL SWITCH DIMENSIONS (17.0) .669 See Pixel Detail Terminal numbers are not on the switch. (3.9) .154 (16.56) .652 (18.0) .709 Standoff 1 Standoff 2 (0.6) Typ .024 (20.59) .811 (14.8) .583 (11.66) .459 2 (13.0) .512 See Standoff Detail (23.0) .906 (23.13) .911 (0.345) .0136 (16.0) .630 (0.4) Typ .016 (18.5) .728 Pixel Detail (1.0) Typ .039 (0.239) .0094 (0.02) Typ .0008 (0.2) .008 Standoff Detail (3.4) .134 1 Standoff 2 (2.0) .079 (18.0) .709 (2.0) Dia .079 Dimension A Standoff 1 = (2.7) Standoff 2 = (2.3) .091 .106 www.nkk.com (7.05) .278 (8.0) .315 A (1.25) .049 Footprint (1.0) Typ .039 9 3 2x (0.9) .035 2 8 4 1 7x (0.75) .030 (2.0) .079 (6.0) .236 Standoff 1 (0.3) Typ .012 (6.0) .236 2 9 8 7 6 5 4 3 (7.62) .300 (7.05) .278 (8.0) .315 (7.62) .300 (16.0) .630 4x (1.3) Dia .051 SmartSwitch TM Wide View/Long Travel LCD 64 x 32 Pushbutton LCD SPECIFICATIONS Characteristics of Display Display Operation Mode FSTN positive; background colors, black & white Display Condition Transflective with built-in LED backlight Viewing Angle Direction 6 o’clock Viewing Area 17.0mm x 13.0mm (horizontal x vertical) Pixel Format 64 x 32 pixels (horizontal x vertical) Pixel Size 0.239mm x 0.345mm (horizontal x vertical) *Operating Temperature Range –15°C ~ +50°C (+5°F ~ +122°F) Storage Temperature Range –20°C ~ +60°C (–4°F ~ +140°F) Backlight LED RGB: red/green/blue * In a low temperature environment (below 0°C), speed and contrast decrease when image changes. The non-indicator dot may become dense in a high temperature environment (about +50°C). Highest backlight brightness level should not be used for temperatures above +35°C. Absolute Maximum Ratings (Temperature at 25°C) Items Symbols Ratings Supply Voltage VDD –0.3V to +7.0V Input Voltage VI –0.3V to VD D +0.3V Output Voltage VO –0.3V to VD D +0.3V Optical Characteristics (Temperature at 25°C) Items Symbols Min Typical Max Cr –– 3.0 –– Up & Down q –– 90° –– Right & Left f –– 90° –– Contrast Ratio Viewing Angle (Cr ≥ 1.1) Recommended Operating Conditions (Temperature at 25°C) Items Symbols Minimum Typical Maximum Supply Voltage VDD 4.9V 5.0V 5.1V High Level Input Voltage VI H 0.8 VDD — — Low Level Input Voltage VI L — — 0.2VDD SPI Clock Frequency fSC K — — 8MHz Current Consumption I DD ** 10mA — *** 60mA ** 10mA: Backlighting LED is off *** 60mA: Backlighting LEDs (Red, Green, Blue) are maximum brightness www.nkk.com 3 SmartSwitch TM Wide View/Long Travel LCD 64 x 32 Pushbutton SWITCH BLOCK DIAGRAM & PIN CONFIGURATIONS Com1......Com32 Common Driver 32bit Shift Register 64 x 32 Dot Matrix LCD Panel seg1.......seg64 Segment Driver Backlight LED Display Controller NC 9 SS 8 SCK 7 SDI 6 RAM #1 256Byte 64bit Shift Register Red Green Blue RAM #2 256Byte LED Driver SPI SDO 5 VDD 4 GND 3 SW Pin No. 4 Symbol 2 SW 1 Name Function 1 SW Terminal of Switch Normally open 2 SW Terminal of Switch Normally open 3 GND 4 VDD Power Power source for logic circuit and LCD 5 SDO Data Out Data output line for SPI 6 SDI Data In Data input line for SPI 7 SCK Serial Clock Clock line for SPI that synchronizes commands and data 8 SS Slave Select Chip select for SPI; line is active low 9 NC None No connection Ground www.nkk.com SmartSwitch TM Handling & Storage PRECAUTIONS FOR HANDLING & STORAGE OF LCD 64 x 32 DEVICES Handling ATTENTION ELECTROSTATIC SENSITIVE DEVICES 1. The IS Series devices are electrostatic sensitive. 2. Limit operating force to keytop to 100.0N maximum, as excessive pressure may damage the LCD device. 3. The IS series devices are not process sealed. 4. If the LCD is accidentally broken, avoid contact with the liquid and wash off any liquid spills to the skin or clothing. 5. Clean cap surface with dry cloth. If further cleaning is needed, wipe with dampened cloth using neutral cleanser and dry with clean cloth. Do not use organic solvent. 6. Recommended soldering time and temperature limits: Do not exceed 60°C at the LCD level. Wave Soldering: see Profile B in Supplement section. Manual Soldering: see Profile A in Supplement section. 7. Excessive images may result after the same image is emitted continuously for an extended period of time. 8. The highest backlight brightness level should not be used for temperatures above +35°C. Storage 1. Store in original container and away from direct sunlight. 2. Keep away from static electricity. 3. Avoid extreme temperatures, high humidity, gaseous substances, and all forms of chemical contamination. www.nkk.com 5