Ordering number : ENA0704C LC87F1A32A CMOS IC 8-bit Microcontroller with Full-Speed USB http://onsemi.com 32K-byte Flash ROM / 2048-byte RAM / 48-pin Overview The LC87F1A32A is an 8-bit microcomputer that, integrates on a single chip a number of hardware features such as 32K-byte flash ROM, 2048-byte RAM, an on-chip debugger, 16-bit timers/counters, a 16-bit timer, two 8-bit timers, a base timer serving as a time-of-day clock, a high-speed clock counter, two channels of synchronous SIO interface (with automatic block transmission/reception capabilities), an asynchronous/synchronous SIO interface, a UART interface, a full-speed USB interface (function), a 12-channel AD converter (12- or 8-bit resolution selectable), two channels of 12-bit PWM, a system clock frequency divider, an infrared remote controller receiver circuit, and an interrupt feature. Features Flash ROM 32768 8 bits Capable of on-board-programming with wide range, 3.0 to 5.5V, of voltage source. Block-erasable in 128 byte units Writable in 2-byte units RAM 2048 9 bits 36 35 34 33 32 31 30 29 28 27 26 25 P27/INT5 P26/INT5 P25/INT5 P24/INT5/SCK4 P23/INT4/SI4/WR P22/INT4/SO4/RD Package Form SQFP48(77) : Lead-Free, Halogen free product P21/INT4/URX1 P20/INT4/UTX1 P07/AN7/T7O P06/AN6/T6O P05/AN5/CKO P04/AN4 SQFP48(7X7) 37 24 38 23 39 22 40 21 20 41 42 LC87F1A32A 43 19 18 44 17 45 16 46 15 47 14 P03/AN3 P02/AN2 P01/AN1 P00/AN0 VSS2 VDD2 PWM0 PWM1 P17/T1PWMH/BUZ P16/T1PWML P15/SCK1 P14/SI1/SB1 ORDERING INFORMATION XT1/AN10 XT2/AN11 VSS1 CF1 CF2 VDD1 P10/SO0 P11/SI0/SB0 P12/SCK0 P13/SO1 * This product is licensed from Silicon Storage Technology, Inc. (USA). P73/INT3/T0IN/RMIN RES 1 2 3 4 5 6 7 8 9 10 11 12 DD+ VDD3 VSS3 P34/UFILT P33 P32/DBG2 P31/DBG1 P30/DBG0 P70/INT0/T0LCP/AN8/DPUP P71/INT1/T0HCP/AN9 P72/INT2/T0IN Top view See detailed ordering and shipping information on page 26 of this data sheet. Semiconductor Components Industries, LLC, 2014 July, 2014 72914HK 20140728-S00015/50814HK/D1212HK/62707HKIM No.A0704-1/26 LC87F1A32A Minimum Bus Cycle 83.3ns (CF=12MHz) Note: The bus cycle time here refers to the ROM read speed. Minimum Instruction Cycle Time 250ns (CF=12MHz) Ports I/O ports Ports whose I/O direction can be designated in 1 bit units 28 (P10 to P17, P20 to P27, P30 to P34, P70 to P73, PWM0, PWM1, XT2) Ports whose I/O direction can be designated in 4 bit units 8 (P00 to P07) USB ports 2 (D+, D-) Dedicated oscillator ports 2 (CF1, CF2) Input-only port (also used for oscillation) 1 (XT1) Reset pins 1 (RES) Power pins 6 (VSS1 to 3, VDD1 to 3) Timers Timer 0: 16-bit timer/counter with a capture register. Mode 0: 8-bit timer with an 8-bit programmable prescaler (with an 8-bit capture register) 2 channels Mode 1: 8-bit timer with an 8-bit programmable prescaler (with an 8-bit capture register) + 8-bit counter (with an 8-bit capture register) Mode 2: 16-bit timer with an 8-bit programmable prescaler (with a 16-bit capture register) Mode 3: 16-bit counter (with a 16-bit capture register) Timer 1: 16-bit timer/counter that supports PWM/toggle outputs Mode 0: 8-bit timer with an 8-bit prescaler (with toggle outputs) + 8-bit timer/counter with an 8-bit prescaler (with toggle outputs) Mode 1: 8-bit PWM with an-8bit prescaler 2 channels Mode 2: 16-bit timer/counter with an 8-bit prescaler (with toggle outputs) (toggle outputs also possible from the lower-order 8 bits) Mode 3: 16-bit timer with an 8-bit prescaler (with toggle outputs) (The lower-order 8 bits can be used as PWM.) Timer 6: 8-bit timer with a 6-bit prescaler (with toggle output) Timer 7: 8-bit timer with a 6-bit prescaler (with toggle output) Base timer 1) The clock is selectable from the subclock (32.768kHz crystal oscillation), system clock, and timer 0 prescaler output. 2) Interrupts programmable in 5 different time schemes No.A0704-2/26 LC87F1A32A SIO SIO0: Synchronous serial interface 1) LSB first/MSB first mode selectable 2) Transfer clock cycle: 4/3 to 512/3 tCYC 3) Automatic continuous data transmission (1 to 256 bits, specifiable in 1 bit units, suspension and resumption of data transmission possible in 1 byte units) SIO1: 8-bit asynchronous/synchronous serial interface Mode 0: Synchronous 8-bit serial I/O (2- or 3-wire configuration, 2 to 512 tCYC transfer clocks) Mode 1: Asynchronous serial I/O (half-duplex, 8 data bits, 1 stop bit, 8 to 2048 tCYC baudrates) Mode 2: Bus mode 1 (start bit, 8 data bits, 2 to 512 tCYC transfer clocks) Mode 3: Bus mode 2 (start detect, 8 data bits, stop detect) SIO4: Synchronous serial interface 1) LSB first/MSB first mode selectable 2) Transfer clock cycle: 4/3 to 1020/3 tCYC 3) Automatic continuous data transmission (1 to 2048 bytes, specifiable in 1 byte units, suspension and resumption of data transmission possible in 1 byte or 2 bytes units) 4) Auto-start-on-falling-edge function 5) Clock polarity selectable 6) CRC16 calculator circuit built in Full Duplex UART 1) Data length: 7/8/9 bits selectable 2) Stop bits: 1 bit (2 bits in continuous transmission mode) 3) Baud rate: 16/3 to 8192/3 tCYC AD Converter: 12 bits 12 channels 12-/8-bit resolution selectable AD converter Reference-voltage automatic generation control PWM: Multifrequency 12-bit PWM 2 channels Infrared Remote Controller Receiver Circuit 1) Noise rejection function (noise filter time constant: Approx. 120s when the 32.768kHz crystal oscillator is selected as the reference voltage source) 2) Supports data encoding systems such as PPM (Pulse Position Modulation) and Manchester encoding 3) X'tal HOLD mode release function USB Interface (function controller) Compliant with USB 2.0 Full-Speed Supports a maximum of 4 user-defined endpoints. Endpoint EP0 EP1 EP2 EP3 EP4 Transfer Control - - - - Type Bulk - Interrupt - Isochronous - 64 64 64 64 64 Max. payload Watchdog Timer External RC watchdog timer Interrupt and reset signals selectable Clock Output Function 1) Able to output selected oscillation clock 1/1, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64 as system clock. 2) Able to output oscillation clock of sub clock. No.A0704-3/26 LC87F1A32A Interrupts 28 sources, 10 vector addresses 1) Provides three levels (low (L), high (H), and highest (X)) of multiplex interrupt control. Any interrupt requests of the level equal to or lower than the current interrupt are not accepted. 2) When interrupt requests to two or more vector addresses occur at the same time, the interrupt of the highest level takes precedence over the other interrupts. For interrupts of the same level, the interrupt into the smallest vector address takes precedence. No. Vector Address Level Interrupt Source 1 00003H X or L INT0 2 0000BH X or L INT1 3 00013H H or L INT2/T0L/INT4/USB bus active/Remote control receive 4 0001BH H or L INT3/INT5/base timer 5 00023H H or L T0H 6 0002BH H or L T1L/T1H 7 00033H H or L SIO0/USB bus reset/USB suspend/UART1 receive 8 0003BH H or L SIO1/USB endpoint/USB-SOF/SIO4/UART1 transmit 9 00043H H or L ADC/T6/T7 10 0004BH H or L Port 0/PWM0/PWM1 Priority Level: X > H > L Of interrupts of the same level, the one with the smallest vector address takes precedence. Subroutine Stack Levels: 1024 levels (the stack is allocated in RAM.) High-speed Multiplication/Division Instructions 16 bits 8 bits (5 tCYC execution time) 24 bits 16 bits (12 tCYC execution time) 16 bits 8 bits (8 tCYC execution time) 24 bits 16 bits (12 tCYC execution time) Oscillation Circuits RC oscillation circuit (internal): CF oscillation circuit: Crystal oscillation circuit: PLL circuit (internal): For system clock For system clock For system clock, time-of-day clock For USB interface (see Fig.5) Standby Function HALT mode: Halts instruction execution while allowing the peripheral circuits to continue operation. 1) Oscillation is not halted automatically. 2) Canceled by a system reset or occurrence of an interrupt. HOLD mode: Suspends instruction execution and the operation of the peripheral circuits. 1) The PLL base clock generator , CF, RC and crystal oscillators automatically stop operation. 2) There are four ways of resetting the HOLD mode. (1) Setting the reset pin to the lower level. (2) Setting at least one of the INT0, INT1, INT2, INT4, and INT5 pins to the specified level (3) Having an interrupt source established at port 0 (4) Having an bus active interrupt source established in the USB interface circuit X'tal HOLD mode: Suspends instruction execution and the operation of the peripheral circuits except for reception of a remote control signal. 1) The PLL base clock generator, CF and RC oscillator automatically stop operation. 2) The state of crystal oscillation established when the X'tal HOLD mode is entered is retained. 3) There are six ways of resetting the X'tal HOLD mode. (1) Setting the reset pin to the low level (2) Setting at least one of the INT0, INT1, INT2, INT4, and INT5 pins to the specified level (3) Having an interrupt source established at port 0 (4) Having an interrupt source established in the base timer circuit (5) Having an bus active interrupt source established in the USB interface circuit (6) Having an interrupt source established in the infrared remote controller receiver circuit. No.A0704-4/26 LC87F1A32A Development Tools On-chip debugger: TCB87 type-B + LC87F1A32A Flash ROM Programming Boards Package Programming boards SQFP48(77) W87F55256SQ Recommended EPROM Programmer Maker Model Flash Support Group, Inc. AF9708/AF9709/AF9709B (Single) (including product of Ando Electric Co., Ltd.) Our company SKK (SanyoFWS) Supported version Device After Rev02.73 LC87F1A32A Application Version: After 1.03 LC87F1A32 Chip Data Version: After 2.07 Package Dimensions unit : mm SPQFP48 7x7 / SQFP48 CASE 131AJ ISSUE A 0.5 0.2 9.0 0.2 9.0 0.2 48 7.0 0.1 7.0 0.1 1 2 0.5 +0.08 0.03 0.18 0.15 0.05 0.10 (1.5) 0~10° 0.1±0.1 1.7 MAX (0.75) 0.10 GENERIC MARKING DIAGRAM* SOLDERING FOOTPRINT* 8.40 XXXXXXXX YDD 8.40 (Unit: mm) XXXXX = Specific Device Code Y = Year DD = Additional Traceability Data XXXXXXXX YMDDD XXXXX = Specific Device Code Y = Year M = Month DDD = Additional Traceability Data 0.50 0.28 1.00 *This information is generic. Please refer to device data sheet for actual part marking. NOTE: The measurements are not to guarantee but for reference only. *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. No.A0704-5/26 LC87F1A32A DD+ VDD3 VSS3 P34/UFILT P33 P32/DBG2 P31/DBG1 P30/DBG0 P70/INT0/T0LCP/AN8/DPUP P71/INT1/T0HCP/AN9 P72/INT2/T0IN LC87F1A32A 24 23 22 21 20 19 18 17 16 15 14 13 P03/AN3 P02/AN2 P01/AN1 P00/AN0 VSS2 VDD2 PWM0 PWM1 P17/T1PWMH/BUZ P16/T1PWML P15/SCK1 P14/SI1/SB1 P73/INT3/T0IN/RMIN RES XT1/AN10 XT2/AN11 VSS1 CF1 CF2 VDD1 P10/SO0 P11/SI0/SB0 P12/SCK0 P13/SO1 1 2 3 4 5 6 7 8 9 10 11 12 37 38 39 40 41 42 43 44 45 46 47 48 36 35 34 33 32 31 30 29 28 27 26 25 P27/INT5 P26/INT5 P25/INT5 P24/INT5/SCK4 P23/INT4/SI4/WR P22/INT4/SO4/RD P21/INT4/URX1 P20/INT4/UTX1 P07/AN7/T7O P06/AN6/T6O P05/AN5/CKO P04/AN4 Pin Assignment Top view SQFP48(77) “Lead-free Type” SQFP48 NAME SQFP48 NAME 1 P73/INT3/T0IN/RMIN 25 P04/AN4 2 RES 26 P05/AN5/CKO 3 XT1/AN10 27 P06/AN6/T6O 4 XT2/AN11 28 P07/AN7/T7O 5 VSS1 29 P20/INT4/UTX1 6 CF1 30 P21/INT4/URX1 7 CF2 31 P22/INT4/SO4/RD 8 VDD1 32 P23/INT4/SI4/WR P24/INT5/SCK4 9 P10/SO0 33 10 P11/SI0/SB0 34 P25/INT5 11 P12/SCK0 35 P26/INT5 12 P13/SO1 36 P27/INT5 13 P14/SI1/SB1 37 D- 14 P15/SCK1 38 D+ 15 P16/T1PWML 39 VDD3 16 P17/T1PWMH/BUZ 40 VSS3 17 PWM1 41 P34/UFILT 18 PWM0 42 P33 19 VDD2 43 P32/DBGP2 20 VSS2 44 P31/ DBGP1 21 P00/AN0 45 P30/ DBGP0 22 P01/AN1 46 P70/INT0/T0LCP/AN8/DPUP 23 P02/AN2 47 P71/INT1/T0HCP/AN9 24 P03/AN3 48 P72/INT2/T0IN No.A0704-6/26 LC87F1A32A System Block Diagram Interrupt control Standby control CF USB PLL RC Clock generator X’tal PLA IR FROM PC SIO0 Bus interface ACC SIO1 Port 0 B register SIO4 Port 1 C register Timer 0 Port 2 ALU Timer 1 Port 3 Timer 6 Port 7 Timer 7 INT0 to 5 Noise filter Base timer UART1 PWM0 ADC Stack pointer PWM1 Infrared remote controller receiver circuit Watchdog timer USB interface PSW RAR RAM On-chip debugger No.A0704-7/26 LC87F1A32A Pin Description Pin Name VSS1, VSS2, I/O Description Option - - power supply pin No - + power supply pin No VDD3 - USB reference voltage pin Yes Port 0 I/O • 8-bit I/O port Yes VSS3 VDD1, VDD2 • I/O specifiable in 4-bit units P00 to P07 • Pull-up resistors can be turned on and off in 4-bit units. • HOLD reset input • Port 0 interrupt input • Pins functions AD converter input port: AN0 to AN7 (P00 to P07) P05: System Clock Output P06: Timer 6 toggle outputs P07: Timer 7 toggle outputs Port 1 I/O Yes • 8-bit I/O port • I/O specifiable in 1-bit units P10 to P17 • Pull-up resistors can be turned on and off in 1-bit units. • Pin functions P10: SIO0 data output P11: SIO0 data input/bus I/O P12: SIO0 clock I/O P13: SIO1 data output P14: SIO1 data input/bus I/O P15: SIO1 clock I/O P16: Timer 1 PWML output P17: Timer 1 PWMH output/beeper output Port 2 P20 to P27 I/O • 8-bit I/O port Yes • I/O specifiable in 1-bit units • Pull-up resistors can be turned on and off in 1-bit units. • Pin functions P20 to P23: INT4 input/HOLD reset input/timer 1 event input/timer 0L capture input/ timer 0H capture input P24 to P27: INT5 input/HOLD reset input/timer 1 event input/timer 0L capture input/ timer 0H capture input P20: UART1 transmit P21: UART1 receive P22: SIO4 date I/O/parallel interface RD output P23: SIO4 date I/O/parallel interface WR output P24: SIO4 clock I/O Interrupt acknowledge type Rising Falling INT4 enable enable INT5 enable enable Rising & H level L level enable disable disable enable disable disable Falling Continued on next page. No.A0704-8/26 LC87F1A32A Continued from preceding page. Pin Name Port 3 I/O I/O Description Option • 5-bit I/O port Yes • I/O specifiable in 1-bit units P30 to P34 • Pull-up resistors can be turned on and off in 1-bit units. • Pin functions P34: USB interface PLL filter pin (see Fig.5) Onchip debugger pin: DBGP0 to DBGP2 (P30 to P32) Port 7 I/O No • 4-bit I/O port • I/O specifiable in 1-bit units P70 to P73 • Pull-up resistors can be turned on and off in 1-bit units. • Pin functions P70: INT0 input/HOLD reset input/timer 0L capture input/watchdog timer output/ D+ 1.5k pull-up resistor connect pin P71: INT1 input/HOLD reset input/timer 0H capture input P72: INT2 input/HOLD reset input/timer 0 event input/timer 0L capture input/ High speed clock counter input P73: INT3 input (input with a noise filter)/timer 0 event input/ timer 0H capture input/ infrared remote controller receiver input AD converter input port: AN8(P70), AN9(P71) Interrupt acknowledge type PWM0 I/O PWM1 D- Rising & Rising Falling INT0 enable enable disable INT1 enable enable disable enable enable INT2 enable enable enable disable disable INT3 enable enable enable disable disable Falling • PWM0 and PWM1 output port H level L level enable enable No • General-purpose input port I/O • USB data I/O pin D- No • General-purpose I/O port D+ I/O • USB data I/O pin D+ No • General-purpose I/O port RES Input XT1 Input Reset pin No • 32.768kHz crystal oscillator input pin No • Pin functions General-purpose input port AD converter input port: AN10 Must be connected to VDD1 if not to be used. XT2 I/O 32.768kHz crystal oscillator output pin No • Pin functions General-purpose I/O port AD converter input port: AN11 Must be set for oscillation and kept open if not to be used. CF1 Input CF2 Output Ceramic resonator input pin No Ceramic resonator output pin No No.A0704-9/26 LC87F1A32A Port Output Types The table below lists the types of port outputs and the presence/absence of a pull-up resistor. Data can be read into any input port even if it is in the output mode. Port Name Option Selected in Units of P00 to P07 1 bit P10 to P17 1 bit P20 to P27 Option Type 1 Output Type Pull-up Resistor CMOS Programmable (Note 1) 2 Nch-open drain No 1 CMOS Programmable 2 Nch-open drain Programmable Programmable P30 to P34 P70 - No Nch-open drain P71 to P73 - No CMOS Programmable PWM0, PWM1 - No CMOS No D+, D- - No CMOS No XT1 - No Input only No XT2 - No 32.768kHz crystal oscillator output No (Nch-open drain when in general-purpose output mode) Note 1: Programmable pull-up resistors for port 0 are controlled in 4 bit units (P00 to 03, P04 to 07). Power Pin Treatment Connect the IC as shown below to minimize the noise input to the VDD1 pin. Be sure to electrically short the VSS1, VSS2, and VSS3 pins. Example 1: When the microcontroller is in the backup state in the HOLD mode, the power to sustain the high level of output ports is supplied by their backup capacitors. LSI Power supply For backup VDD1 VDD2 VDD3 VSS1 VSS2 VSS3 Example 2: The high level output at ports is not sustained and unstable in the HOLD backup mode. LSI Power supply For backup VDD1 VDD2 VDD3 VSS1 VSS2 VSS3 No.A0704-10/26 LC87F1A32A USB Reference Power Option When a voltage 4.4 to 5.5V is supplied to VDD1 and the internal USB reference voltage circuit is activated, the reference voltage for USB port output is generated. The active/inactive state of reference voltage circuit can be switched by the option select. The procedure for marking the option selection is described below. (1) Option select (2) (3) (4) NONUSE USB Regulator USE USE USE USB Regulator at HOLD mode USE NONUSE NONUSE NONUSE USB Regulator at HALT mode USE NONUSE USE NONUSE inactive Reference voltage circuit Normal state active active active state HOLD mode active inactive inactive inactive HALT mode active inactive active inactive When the USB reference voltage circuit is made inactive, the level of the reference voltage for USB port output is equal to VDD1. Selection (2) or (3) can be used to set the reference voltage circuit inactive in HOLD or HALT mode. When the reference voltage circuit is activated, the current drain increase by approximately 100A compared with when the reference voltage circuit is inactive. Example 1: VDD1=VDD2=3.3V Inactivating the reference voltage circuit (selection (4)). Connecting VDD3 to VDD1 and VDD2. LSI P70 For backup 1.5k Power supply 3.3V VDD1 VDD2 VDD3 D+ To USB connector 27 to 33 D- UFILT 5pF 0 VSS1 VSS2 VSS3 2.2F Example 2: VDD1=VDD2=5.0V Activating the reference voltage circuit (selection (1)). Isolating VDD3 from VDD1 and VDD2, and connecting capacitor between VDD3 and VSS. LSI P70 1.5k For backup Power supply 5V VDD1 D+ To USB connector 27 to 33 DVDD2 5pF VDD3 2.2F UFILT 0 0.1µF VSS1 VSS2 VSS3 2.2F No.A0704-11/26 LC87F1A32A Absolute Maximum Ratings at Ta = 25°C, VSS1 = VSS2 = VSS3 = 0V Parameter Maximum supply Symbol Pin/Remarks VDD max VDD1, VDD2, VDD3 Input voltage VI(1) XT1, CF1 Input/output VIO(1) Ports 0, 1, 2, 3, 7 Conditions VDD1=VDD2=VDD3 voltage voltage Peak output PWM0, PWM1, XT2 IOPH(1) Ports 0, 1, 2 current Specification VDD[V] min typ max unit 0.3 +6.5 0.3 VDD+0.3 0.3 VDD+0.3 V • When CMOS output type is selected 10 • Per 1 applicable pin IOPH(2) PWM0, PWM1 Per 1 applicable pin IOPH(3) Ports 3 • When CMOS output P71 to P73 type is selected 20 5 High level output current • Per 1 applicable pin Average IOMH(1) Ports 0, 1, 2 output type is selected current (Note 1-1) • When CMOS output 7.5 • Per 1 applicable pin IOMH(2) PWM0, PWM1 Per 1 applicable pin IOMH(3) Ports 3 • When CMOS output P71 to P73 type is selected 15 3 • Per 1 applicable pin Total output IOAH(1) Ports 0, 2 Total of all applicable pins current IOAH(2) Port 1 Total of all applicable pins PWM0, PWM1 IOAH(3) Ports 0, 1, 2 Total of all applicable pins PWM0, PWM1 IOAH(4) Ports 3 Total of all applicable pins P71 to P73 Peak output IOAH(5) D+, D Total of all applicable pins IOPL(1) P02 to P07 Per 1 applicable pin current 25 25 45 10 mA 25 20 Ports 1, 2 Low level output current PWM0, PWM1 Average IOPL(2) P00, P01 Per 1 applicable pin 30 IOPL(3) Ports 3, 7, XT2 Per 1 applicable pin 10 IOML(1) P02 to P07 Per 1 applicable pin output Ports 1, 2 current PWM0, PWM1 (Note 1-1) 15 IOML(2) P00, P01 Per 1 applicable pin 20 IOML(3) Ports 3, 7, XT2 Per 1 applicable pin 7.5 Total output IOAL(1) Ports 0, 2 Total of all applicable pins 45 current IOAL(2) Port 1 Total of all applicable pins 45 PWM0, PWM1 IOAL(3) Ports 0, 1, 2 Total of all applicable pins 80 PWM0, PWM1 Allowable power IOAL(4) Ports 3, 7, XT2 Total of all applicable pins 15 IOAL(5) D+, D Total of all applicable pins 25 Pd max SQFP48(77) Ta=-30to+70C 190 Dissipation Operating ambient Topr Temperature Storage ambient Tstg temperature 30 +70 55 +125 mW C Note 1-1: The mean output current is a mean value measured over 100ms. Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. No.A0704-12/26 LC87F1A32A Allowable Operating Conditions at Ta = 30°C to +70°C, VSS1 = VSS2 = VSS3 = 0V Parameter Operating Symbol VDD(1) Pin/Remarks VDD1=VDD2=VDD3 supply voltage Specification VDD[V] 0.245s tCYC 200s 0.245s tCYC 0.383s USB circuit operation mode 0.490s tCYC 200s Except for onboard programming (Note 2-1) Memory Conditions VHD VDD1=VDD2=VDD3 sustaining min typ max unit 3.0 5.5 3.0 5.5 2.7 5.5 2.0 5.5 0.3VDD VDD RAM and register contents sustained in HOLD mode. supply voltage High level VIH(1) input voltage Ports 0, 1, 2, 3 P71 to P73 2.7 to 5.5 P70 port input/ interrupt side +0.7 PWM0, PWM1 VIH(2) V Port 70 watchdog timer side Low level VIH(3) XT1, XT2, CF1, RES VIL(1) Ports 1, 2, 3 input voltage P71 to P73 VIL(2) P70 port input/ interrupt side VIL(3) Port 0 PWM0, PWM1 VIL(4) VIL(5) Port 70 watchdog timer side VIL(6) Instruction XT1, XT2, CF1, RES tCYC cycle time Except for onboard (Note 2-2) programming External FEXCF(1) CF1 2.7 to 5.5 0.9VDD VDD 2.7 to 5.5 0.75VDD 4.0 to 5.5 VSS VDD 0.1VDD +0.4 2.7 to 4.0 VSS 0.2VDD 4.0 to 5.5 VSS 2.7 to 4.0 VSS 2.7 to 5.5 VSS 2.7 to 5.5 VSS 0.25VDD 3.0 to 5.5 0.245 200 2.7 to 5.5 0.490 200 3.0 to 5.5 0.1 12 0.15VDD +0.4 0.2VDD 0.8VDD 1.0 s • CF2 pin open • System clock frequency system clock division ratio=1/1 frequency • External system clock duty =505% MHz • CF2 pin open • System clock frequency division ratio=1/1 2.7 to 5.5 0.1 6 • External system clock duty =505% Oscillation FmCF(1) CF1, CF2 See Fig. 1. frequency range 12 MHz ceramic oscillation FmCF(2) CF1, CF2 (Note 2-3) 6 MHz ceramic oscillation See Fig. 1. FmRC FsX’tal Internal RC oscillation XT1, XT2 32.768kHz crystal oscillation See Fig. 2. 3.0 to 5.5 12 2.7 to 5.5 6 2.7 to 5.5 2.7 to 5.5 0.3 1.0 MHz 2.0 32.768 kHz Note 2-1: VDD must be held greater than or equal to 3.0V in the flash ROM onboard programming mode. Note 2-2: Relationship between tCYC and oscillation frequency is 3/FmCF at a division ratio of 1/1 and 6/FmCF at a division ratio of 1/2. Note 2-3: See Tables 1 and 2 for the oscillation constants. Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. No.A0704-13/26 LC87F1A32A Electrical Characteristics at Ta = 30°C to +70°C, VSS1 = VSS2 = VSS3 = 0V Parameter High level input Symbol IIH(2) IIH(3) CF1 VIN=VDD IIL(1) IIL(2) Ports 0, 1, 2, 3 Port 7 RES PWM0, PWM1 D+, D XT1, XT2 Output disabled Pull-up resistor off VIN=VSS (Including output Tr's off leakage current) For input port specification VIN=VSS VIN=VSS current IIL(3) CF1 High level output VOH(1) voltage VOH(2) Ports 0, 1, 2, 3 P71 to P73 VOH(3) VOH(4) VOH(5) VOH(6) Low level output VOL(1) voltage VOL(2) PWM0, PWM1 P05 (CK0 when using system clock output function) P00, P01 VOL(3) VOL(4) VOL(5) VOL(6) VOL(7) Ports 0, 1, 2 PWM0, PWM1 XT2 Ports 3, 7 VOL(8) Pull-up resistance Rpu(1) Rpu(2) Hysteresis voltage Pin capacitance Conditions Ports 0, 1, 2, 3 Port 7 RES PWM0, PWM1 D+, D XT1, XT2 IIH(1) current Low level input Pin/Remarks VHYS CP Ports 0, 1, 2, 3 Port 7 RES Ports 1, 2, 3, 7 All pins Output disabled Pull-up resistor off VIN=VDD (Including output Tr's off leakage current) For input port specification VIN=VDD Specification VDD[V] min typ max unit 2.7 to 5.5 1 2.7 to 5.5 1 2.7 to 5.5 15 2.7 to 5.5 1 2.7 to 5.5 1 2.7 to 5.5 15 IOH=1mA 4.5 to 5.5 VDD1 IOH=0.4mA 3.0 to 5.5 VDD0.4 IOH=0.2mA 2.7 to 5.5 VDD0.4 IOH=10mA 4.5 to 5.5 VDD1.5 IOH=1.6mA 3.0 to 5.5 VDD0.4 IOH=1mA 2.7 to 5.5 VDD0.4 IOL=30mA 4.5 to 5.5 1.5 IOL=5mA 3.0 to 5.5 0.4 IOL=2.5mA 2.7 to 5.5 0.4 IOL=10mA 4.5 to 5.5 1.5 IOL=1.6mA 3.0 to 5.5 0.4 IOL=1mA 2.7 to 5.5 0.4 IOL=1.6mA 3.0 to 5.5 0.4 IOL=1mA 2.7 to 5.5 VOH=0.9VDD 4.5 to 5.5 15 35 80 2.7 to 5.5 18 50 150 For pins other than that under test: VIN=VSS f=1MHz Ta=25C A V 0.4 k 2.7 to 5.5 0.1VDD V 2.7 to 5.5 10 pF Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. No.A0704-14/26 LC87F1A32A Serial I/O Characteristics at Ta = 30°C to +70°C, VSS1 = VSS2 = VSS3 = 0V 1. SIO0 Serial I/O Characteristics (Note 4-1-1) Parameter Symbol Frequency tSCK(1) Low level tSCKL(1) Pin/Remarks SCK0(P12) Conditions Specification VDD[V] See Fig.9. typ max unit 2 1 pulse width High level min tSCKH(1) 1 pulse width tSCKHA(1a) • Continuous data transmission/ reception mode • USB nor SIO4 are not in 4 use simultaneous. Input clock • See Fig.8. • (Note 4-1-2) tSCKHA(1b) • Continuous data 2.7 to 5.5 tCYC transmission/reception mode • USB is in use simultaneous. • SIO4 is not in use 7 simultaneous. • See Fig.8. • (Note 4-1-2) tSCKHA(1c) • Continuous data transmission/ reception mode • USB and SIO4 are in use 9 simultaneous. Serial clock • See Fig.8. • (Note 4-1-2) Frequency tSCK(2) SCK0(P12) • CMOS output selected 4/3 • See Fig.8. Low level tSCKL(2) 1/2 pulse width High level tSCK tSCKH(2) 1/2 pulse width tSCKHA(2a) • Continuous data transmission/ reception mode tSCKH(2) • USB nor SIO4 are not in +2tCYC Output clock use simultaneous. • CMOS output selected tSCKH(2) +(10/3) tCYC • See Fig.8. tSCKHA(2b) • Continuous data transmission/ 2.7 to 5.5 reception mode • USB is in use simultaneous. • SIO4 is not in use simultaneous. tSCKH(2) +2tCYC tSCKH(2) +(19/3) tCYC tCYC • CMOS output selected • See Fig.8. tSCKHA(2c) • Continuous data transmission/ reception mode • USB and SIO4 are in use simultaneous. • CMOS output selected tSCKH(2) +2tCYC tSCKH(2) +(25/3) tCYC • See Fig.8. Note 4-1-1: These specifications are theoretical values. Add margin depending on its use. Note 4-1-2: To use serial-clock-input in continuous trans/rec mode, a time from SI0RUN being set when serial clock is "H" to the first negative edge of the serial clock must be longer than tSCKHA. Continued on next page. No.A0704-15/26 LC87F1A32A Continued from preceding page. Parameter Serial input Data setup time tsDI(1) Pin/Remarks SB0(P11), SI0(P11) Conditions Specification VDD[V] min typ max unit • Must be specified with respect to rising edge of SIOCLK. 2.7 to 5.5 0.03 2.7 to 5.5 0.03 • See Fig.8. Data hold time thDI(1) tdD0(1) time SO0(P10), SB0(P11) • Continuous data transmission/reception mode (1/3)tCYC 2.7 to 5.5 +0.05 • (Note 4-1-3) tdD0(2) • Synchronous 8-bit mode • (Note 4-1-3) tdD0(3) Output clock Input clock Output delay Serial output Symbol s 1tCYC 2.7 to 5.5 +0.05 (Note 4-1-3) (1/3)tCYC 2.7 to 5.5 +0.05 Note 4-1-3: Must be specified with respect to falling edge of SIOCLK. Must be specified as the time to the beginning of output state change in open drain output mode. See Fig.8. 2. SIO1 Serial I/O Characteristics (Note 4-2-1) Symbol Frequency tSCK(3) Low level tSCKL(3) Pin/Remarks SCK1(P15) Conditions See Fig.8. Frequency SCK1(P15) • CMOS output selected tSCKL(4) 2 1/2 tSCK tSCKH(4) 1/2 pulse width Serial input Data setup time tsDI(2) SB1(P14), SI1(P14) • Must be specified with respect to rising edge of 2.7 to 5.5 0.03 2.7 to 5.5 0.03 SIOCLK. Data hold time Output delay time • See Fig.8. thDI(2) tdD0(4) SO1(P13), SB1(P14) Serial output unit 1 2.7 to 5.5 pulse width High level max 1 • See Fig.8. Low level typ tCYC tSCKH(3) tSCK(4) min 2 2.7 to 5.5 pulse width High level Specification VDD[V] pulse width Output clock Serial clock Input clock Parameter • Must be specified with s respect to falling edge of SIOCLK. • Must be specified as the time to the beginning of output state 2.7 to 5.5 (1/3)tCYC +0.05 change in open drain output mode. • See Fig.8. Note 4-2-1: These specifications are theoretical values. Add margin depending on its use. No.A0704-16/26 LC87F1A32A 3. SIO4 Serial I/O Characteristics (Note 4-3-1) Parameter Symbol Frequency tSCK(5) Low level tSCKL(5) Pin/ Conditions Remarks SCK4(P24) Specification VDD[V] See Fig.8. typ max unit 2 1 pulse width High level min tSCKH(5) 1 pulse width tSCKHA(5a) • USB nor continuous data Transmission/reception mode Of SIO0 are not in use 4 simultaneous. Input clock • See Fig.8. • (Note 4-3-2) tSCKHA(5b) • USB is in use simultaneous. 2.7 to 5.5 tCYC • Do not use SIO0 continuous data transmission mode at the 7 same time. • See Fig.8. • (Note 4-3-2) tSCKHA(5c) • USB and continuous data transmission/ reception mode of SIO0 are in use 10 simultaneous. Serial clock • See Fig.8. • (Note 4-3-2) Frequency tSCK(6) SCK4(P24) • CMOS output selected 4/3 • See Fig.8 Low level tSCKL(6) 1/2 pulse width High level tSCK tSCKH(6) 1/2 pulse width tSCKHA(6a) • USB, AIF nor continuous data transmission/reception mode of SIO0 are not in use Output clock simultaneous. • CMOS output selected • See Fig.8. tSCKHA(6b) • USB is in use simultaneous. tSCKH(6) tSCKH(6) +(5/3) +(10/3) tCYC tCYC tSCKH(6) tSCKH(6) +(5/3) +(19/3) tCYC tCYC tSCKH(6) tSCKH(6) +(5/3) +(28/3) tCYC tCYC 2.7 to 5.5 • Do not use SIO0 continuous data transmission mode at the same time. • CMOS output selected tCYC • See Fig8. tSCKHA(6c) • USB and continuous data transmission/reception mode of SIO0 are in use simultaneous. • CMOS output selected • See Fig.8. Serial input Data setup time tsDI(3) SO4(P22), SI4(P23) • Must be specified with respect to rising edge of SIOCLK. 2.7 to 5.5 0.03 • See Fig.8. Data hold time s thDI(3) 2.7 to 5.5 0.03 Note 4-3-1: These specifications are theoretical values. Add margin depending on its use. Note 4-3-2: To use serial-clock-input in continuous trans/rec mode, a time from SI4RUN being set when serial clock is "H" to the first negative edge of the serial clock must be longer than tSCKHA. Continued on next page. No.A0704-17/26 LC87F1A32A Continued from preceding page. Parameter Pin/ Symbol Output delay time Conditions Remarks tdD0(5) SO4(P22), Serial output SI4(P23) Specification VDD[V] min typ max unit • Must be specified with respect to rising edge of SIOCLK. • Must be specified as the time to the beginning of output state (1/3)tCYC 2.7 to 5.5 +0.05 s change in open drain output mode. • See Fig.8. Pulse Input Conditions at Ta = 30°C to +70°C, VSS1 = VSS2 = VSS3 = 0V Parameter Symbol Pin/Remarks Conditions High/low level tP1H(1) INT0(P70), • Interrupt source flag can be set. pulse width tP1L(1) INT1(P71), • Event inputs for timer 0 or 1 are INT2(P72), enabled. Specification VDD[V] min typ 2.7 to 5.5 1 2.7 to 5.5 2 2.7 to 5.5 64 2.7 to 5.5 256 max unit INT4(P20 to P23), INT5(P24 to P27) tPIH(2) INT3(P73) when • Interrupt source flag can be set. tPIL(2) noise filter time • Event inputs for timer 0 are constant is 1/1 enabled. tPIH(3) INT3(P73) when • Interrupt source flag can be set. tPIL(3) noise filter time • Event inputs for timer 0 are constant is 1/32 enabled. tPIH(4) INT3(P73) when • Interrupt source flag can be set. tPIL(4) noise filter time • Event inputs for timer 0 are constant is 1/128 tPIL(5) RMIN(P73) tCYC enabled. Recognized by the infrared remote controller receiver circuit as a signal. RMC 2.7 to 5.5 4 2.7 to 5.5 200 K (Note 51) tPIL(6) RES Resetting is enabled. s Note5-1: Represents the period of the reference clock (1 tCYC to 128 tCYC or the source frequency of the subclock) for the infrared remote controller receiver circuit. No.A0704-18/26 LC87F1A32A AD Converter Characteristics at Ta= 30C to +70C, VSS1 = VSS2 = VSS3 = 0V <12-bits AD Converter Mode> Parameter Symbol Pin/Remarks Resolution N AN0(P00) to Absolute accuracy ET AN7(P07) Conversion time TCAD VAIN VDD[V] min 3.0 to 5.5 AN8(P70) AN9(P71) max unit 12 bit 3.0 to 5.5 See conversion time calculation 4.0 to 5.5 32 115 3.0 to 5.5 64 115 3.0 to 5.5 VSS VDD (Note 6-2) AN11(XT2) typ (Note 6-1) formulas. AN10(XT1) Analog input Specification Conditions voltage range Analog port input IAINH VAIN=VDD 3.0 to 5.5 current IAINL VAIN=VSS 3.0 to 5.5 16 LSB s V 1 A 1 <8-bits AD Converter Mode> Parameter Symbol Pin/Remarks Resolution N AN0(P00) to Absolute accuracy ET AN7(P07) Conversion time TCAD VAIN VDD[V] min 3.0 to 5.5 AN8(P70) AN9(P71) max unit 8 bit 3.0 to 5.5 See conversion time calculation 4.0 to 5.5 20 90 3.0 to 5.5 40 90 3.0 to 5.5 VSS VDD (Note 6-2) AN11(XT2) typ (Note 6-1) formulas. AN10(XT1) Analog input Specification Conditions voltage range Analog port input IAINH VAIN=VDD 3.0 to 5.5 current IAINL VAIN=VSS 3.0 to 5.5 1.5 LSB 1 1 s V A Conversion time calculation formulas: 12-bits AD Converter Mode: TCAD (Conversion time) = ((52/(AD division ratio))+2) (1/3) tCYC 8-bits AD Converter Mode: TCAD (Conversion time) = ((32/(AD division ratio))+2) (1/3) tCYC <Recommended Operating Conditions> External Supply Voltage System Clock oscillator Range Division FmCF[MHz] VDD[V] (SYSDIV) 4.0 to 5.5 1/1 3.0 to 5.5 1/1 Cycle Time tCYC [ns] AD Frequency Conversion Time (TCAD)[s] Division Ratio (ADDIV) 12-bit AD 8-bit AD 250 1/8 34.8 21.5 250 1/16 69.5 42.8 12 Note 6-1: The quantization error (1/2LSB) must be excluded from the absolute accuracy. The absolute accuracy must be measured in the microcontroller's state in which no I/O operations occur at the pins adjacent to the analog input channel. Note 6-2: The conversion time refers to the period from the time an instruction for starting a conversion process till the time the conversion results register(s) are loaded with a complete digital conversion value corresponding to the analog input value. The conversion time is 2 times the normal-time conversion time when: The first AD conversion is performed in the 12-bit AD conversion mode after a system reset. The first AD conversion is performed after the AD conversion mode is switched from 8-bit to 12-bit conversion mode. No.A0704-19/26 LC87F1A32A Consumption Current Characteristics at Ta = 30°C to +70°C, VSS1 = VSS2 = VSS3 = 0V Parameter Normal mode Symbol Conditions • FmCF=12MHz ceramic oscillation mode consumption VDD1 =VDD2 current =VDD3 • System clock set to 12MHz side (Note 7-1) IDDOP(1) Pin/ Remarks • FsX’tal=32.768kHz crystal oscillation mode Specification VDD[V] 4.4 to 5.5 min typ max 9.8 24 5.6 14 4.4 to 5.5 14 34 3.0 to 3.6 7.7 19 4.4 to 5.5 6.1 14 3.0 to 3.6 3.7 8.5 • 1/2 frequency division ration 2.7 to 3.0 3.0 6.7 • FmCF=0MHz (oscillation stopped) 4.4 to 5.5 0.63 3.0 3.0 to 3.6 0.35 1.6 2.7 to 3.0 0.30 1.3 4.4 to 5.5 39 150 3.0 to 3.6 17 58 2.7 to 3.0 14 43 4.4 to 5.5 4.9 12 3.0 to 3.6 2.6 6.3 4.4 to 5.5 8.9 23 unit • Internal PLL oscillation stopped IDDOP(2) • Internal RC oscillation stopped 3.0 to 3.6 • USB circuit stopped • 1/1 frequency division ration IDDOP(3) • FmCF=12MHz ceramic oscillation mode • FsX’tal=32.768kHz crystal oscillation mode • System clock set to 12MHz side • Internal PLL oscillation mode IDDOP(4) • Internal RC oscillation stopped • USB circuit operation mode mA • 1/1 frequency division ration IDDOP(5) • FmCF=12MHz ceramic oscillation mode • FsX’tal=32.768kHz crystal oscillation mode IDDOP(6) • System clock set to 6MHz side • Internal RC oscillation stopped IDDOP(7) IDDOP(8) • FsX’tal=32.768kHz crystal oscillation mode IDDOP(9) • System clock set to internal RC oscillation IDDOP(10) • 1/2 frequency division ration IDDOP(11) • FmCF=0MHz (oscillation stopped) • FsX’tal=32.768kHz crystal oscillation mode IDDOP(12) • System clock set to 32.768kHz side • Internal RC oscillation stopped IDDOP(13) HALT mode IDDHALT(1) • 1/2 frequency division ration VDD1 =VDD2 • HALT mode consumption current =VDD3 • FsX’tal=32.768kHz crystal oscillation mode (Note 7-1) • FmCF=12MHz ceramic oscillation mode A • System clock set to 12MHz side IDDHALT(2) • Internal PLL oscillation stopped • Internal RC oscillation stopped • USB circuit stopped • 1/1 frequency division ration IDDHALT(3) • HALT mode • FmCF=12MHz ceramic oscillation mode • FsX’tal=32.768kHz crystal oscillation mode mA • System clock set to 12MHz side IDDHALT(4) • Internal PLL oscillation mode • Internal RC oscillation stopped • USB circuit operation mode 3.0 to 3.6 4.6 12 4.4 to 5.5 3.0 7.2 3.0 to 3.6 1.6 3.8 2.7 to 3.0 1.3 2.9 • 1/1 frequency division ration IDDHALT(5) • HALT mode • FmCF=12MHz ceramic oscillation mode IDDHALT(6) • FsX’tal=32.768kHz crystal oscillation mode • System clock set to 6MHz side IDDHALT(7) • Internal RC oscillation stopped • 1/2 frequency division ration Note 7-1: The consumption current value includes none of the currents that flow into the output Tr and internal pull-up resistors. Continued on next page. No.A0704-20/26 LC87F1A32A Continued from preceding page. Parameter Symbol HALT mode IDDHALT(8) consumption IDDHALT(9) current (Note 7-1) Pin/ Specification Conditions Remarks VDD[V] VDD1 =VDD2 • HALT mode =VDD3 • FsX'tal=32.768kHz crystal oscillation mode 3.0 to 3.6 0.18 0.83 2.7 to 3.0 0.15 0.62 4.4 to 5.5 24 93 3.0 to 3.6 7.9 33 2.7 to 3.0 5.8 22 HOLD mode 4.4 to 5.5 0.08 24 • CF1=VDD or open (External clock mode) 3.0 to 3.6 0.03 11 2.7 to 3.0 0.02 9.6 • FmCF=0MHz (oscillation stopped) • FsX'tal=32.768kHz crystal oscillation mode • System clock set to 32.768kHz side • Internal RC oscillation stopped IDDHALT(13) • 1/2 frequency division ration HOLD mode IDDHOLD(1) consumption IDDHOLD(2) current VDD1 IDDHOLD(3) Timer HOLD IDDHOLD(4) mode IDDHOLD(5) consumption VDD1 Timer HOLD mode 4.4 to 5.5 19 77 • CF1=VDD or open (External clock mode) 3.0 to 3.6 5.1 23 2.7 to 3.0 3.3 14 • FsX’tal=32.768kHz crystal oscillation mode IDDHOLD(6) current unit • FmCF=0MHz (oscillation stopped) • HALT mode IDDHALT(12) max 1.8 • 1/2 frequency division ration IDDHALT(11) typ 0.37 • System clock set to internal RC oscillation IDDHALT(10) min 4.4 to 5.5 mA A Note 7-1: The consumption current value includes none of the currents that flow into the output Tr and internal pull-up resistors. USB Characteristics and Timing at Ta = 0°C to +70°C, VSS1 = VSS2 = VSS3 = 0V Parameter Symbol High level output Specification Conditions min typ max unit VOH(USB) • 15k±5% to GND 2.8 3.6 V Low level output VOL(USB) • 1.5k±5% to 3.6 V 0.0 0.3 V Output signal crossover voltage VCRS 1.3 2.0 Differential input sensitivity VDI Differential input common mode range VCM 0.8 High level input VIH(USB) 2.0 Low level input VIL(USB) USB data rise time tR • |(D+)(D)| 0.2 • RS=27 to 33, CL=50pF • VDD3=3.0 to 3.6V USB data fall time tF • RS=27 to 33, CL=50pF • VDD3=3.0 to 3.6V V V 2.5 V V 0.8 V 4 20 ns 4 20 ns F-ROM Programming Characteristics at Ta = +10C to +55C, VSS1 = VSS2= VSS3 =0V Parameter Onboard Symbol IDDFW(1) programming Pin Conditions VDD1 • Excluding power dissipation in the microcontroller block Specification VDD[V] 3.0 to 5.5 min typ max unit 5 10 mA 20 30 ms 40 60 s current Programming tFW(1) • Erase operation time tFW(2) • Write operation 3.0 to 5.5 No.A0704-21/26 LC87F1A32A Characteristics of a Sample Main System Clock Oscillation Circuit Given below are the characteristics of a sample main system clock oscillation circuit that are measured using a Our designated oscillation characteristics evaluation board and external components with circuit constant values with which the oscillator vendor confirmed normal and stable oscillation. Table 1 Characteristics of a Sample Main System Clock Oscillator Circuit with a Ceramic Oscillator at Ta = 0°C to +70°C Nominal Vendor Frequency Name 6MHz MURATA Circuit Constant Oscillator Name C1 CSTCR6M00G15L**-R0 C2 Operating Oscillation Voltage Stabilization Time Range Rd1 typ Remarks max [pF] [pF] [] [V] [ms] [ms] (39) (39) 680 2.7 to 5.5 0.05 0.50 8MHz MURATA CSTCE8M00G15L**-R0 (33) (33) 220 3.0 to 5.5 0.05 0.50 10MHz MURATA CSTCE10M0G15L**-R0 (33) (33) 220 3.0 to 5.5 0.05 0.50 12MHz MURATA CSTCE12M0G15L**-R0 (33) (33) 330 3.0 to 5.5 0.05 0.50 Built-in C1, C2 The oscillation stabilization time refers to the time interval that is required for the oscillation to get stabilized after VDD goes above the operating voltage lower limit (see Figure 4). Characteristics of a Sample Subsystem Clock Oscillator Circuit Given below are the characteristics of a sample subsystem clock oscillation circuit that are measured using a Our designated oscillation characteristics evaluation board and external components with circuit constant values with which the oscillator vendor confirmed normal and stable oscillation. Table 2 Characteristics of a Sample Subsystem Clock Oscillator Circuit with a CF Oscillator Nominal Vendor Frequency Name 32.768kHz EPSON TOYOCOM Circuit Constant Oscillator Name MC-306 Operating Oscillation Voltage Stabilization Time C3 C4 Rf Rd2 Range typ max [pF] [pF] [] [] [V] [s] [s] 18 18 OPEN 560k 2.7 to 5.5 1.1 3.0 Remarks Applicable CL value=12.5pF The oscillation stabilization time refers to the time interval that is required for the oscillation to get stabilized after the instruction for starting the subclock oscillation circuit is executed and to the time interval that is required for the oscillation to get stabilized after the HOLD mode is reset (see Figure 4). Note: The components that are involved in oscillation should be placed as close to the IC and to one another as possible because they are vulnerable to the influences of the circuit pattern. CF1 CF2 XT1 Rd1 C1 CF C2 XT2 Rf Rd2 C3 C4 X’tal Figure 1 CF Oscillator Circuit Figure 2 XT Oscillator Circuit 0.5VDD Figure 3 AC Timing Measurement Point No.A0704-22/26 LC87F1A32A VDD Operating VDD lower limit GND Power Supply Reset time RES Internal RC oscillation tmsCF CF1, CF2 tmsX’tal XT1, XT2 Operating mode Unpredictable Reset Instruction execution Reset Time and Oscillation Stabilization Time HOLD reset signal HOLD reset signal valid Internal RC oscillation tmsCF CF1, CF2 tmsX’tal XT1, XT2 Operating mode HOLD HALT HOLD Reset Signal and Oscillation Stabilization Time Figure 4 Oscillation Stabilization Time No.A0704-23/26 LC87F1A32A P34/UFILT When using the internal PLL circuit to generate the 48 MHz clock for USB , it is necessary to connect a filter circuit such as that shown to the left to the P34/UFILT pin. Rd 0 + - Cd 2.2F Figure 5 External Filter Circuit for the Internal USB-dedicated PLL Circuit VD3OEN P70 Note: It’s necessary to adjust the Circuit Constant of the USB Port Peripheral Circuit each mounting board. Make the D+ Pull-up resistors available to control on/off according to the Vbus. 1.5k D+ 27 to 33 5pF D27 to 33 5pF Figure 6 USB Port Peripheral Circuit VDD RRES RES CRES Note: Determine the value of CRES and RRES so that the reset signal is present for a period of 200µs after the supply voltage goes beyond the lower limit of the IC's operating voltage. Figure 7 Reset Circuit No.A0704-24/26 LC87F1A32A SIOCLK: DATAIN: DI0 DI1 DI2 DI3 DI4 DI5 DI6 DI7 DI8 DATAOUT: DO0 DO1 DO2 DO3 DO4 DO5 DO6 DO7 DO8 Data RAM transfer period (SIO0, 4 only) tSCK tSCKL tSCKH SIOCLK: tsDI thDI DATAIN: tdDO DATAOUT: Data RAM transfer period (SIO0, 4 only) tSCKL tSCKHA SIOCLK: tsDI thDI DATAIN: tdDO DATAOUT: Figure 8 Serial I/O Waveforms tPIL tPIH Figure 9 Pulse Input Timing Signal Waveform Voh tr D+ tr 90% 90% Vcrs 10% Vol 10% D- Figure 10 USB Data Signal Timing and Voltage Level No.A0704-25/26 LC87F1A32A ORDERING INFORMATION Device LC87F1A32AUWA-2H Package SPQFP-48 / SQFP-48 (Pb-Free / Halogen Free) Shipping (Qty / Packing) 2500 / Tray JEDEC ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf . SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PS No.A0704-26/26