PI3EQX6741ST

PI3EQX6741ST
3.3V, 1-port, SATA Gen 3i ReDriver™ with
Adjustable Equalization/Pre-Emphasis
Features
Description
ÎÎSupports SATA Gen 3i.
Pericom’s PI3EQX6741ST is a low power, signal SATA Gen
3i 6Gbps ReDriver™. The device provides programmable equalization and output emphasis, to optimize performance over a
variety of physical mediums by reducing Inter-Symbol Interference. PI3EQX6741ST supports two 100Ω Differential CML data
I/O’s between the Protocol ASIC to a switch fabric, across a backplane, or to extend the signals across other distant data pathways
on the user’s platform.
ÎÎTwo
6Gbps differential signal pairs
ÎÎ100Ω Differential CML I/O’s
ÎÎInput signal level detect and squelch for each channel
ÎÎOOB Support
ÎÎAutomatic HDD Rate detection for output swing/emphasis
setting
The integrated equalization circuitry provides flexibilitywith
signal integrity of the signal before the ReDriver.
ÎÎTermination detect indication
àà Power saving mode control to Host or HDD
A low-level input signal detection and output squelch function
is provided for each channel. Each channel operates fully independently. When the channels are enabled (EN=1) and operating,
that channels input signal level (on xI+/-) determines whether the
output is active. If the input signal level of the channel falls below
the active threshold level (Vth-) then the outputs are driven to the
common mode voltage.
ÎÎAdjustable Receiver Equalization
ÎÎSelectable Output Pre-emphasis and Swing Control
ÎÎHigh impedance I/O termination in standby mode
ÎÎESD +/-8kV
ÎÎLow Power Operation: 254mW typical
ÎÎAuto-Slumber Mode: 36mW typical
Termination Detect indication (TDet_A# or TDET_B#) provides
indication when the load is connected ie HDD or Host. This can
be used as control to go into power saving mode by either the host
or HDD.
ÎÎHDD unplugged: 3.6mW
ÎÎPower down Stand-by Mode: 0.7mW max
ÎÎSupply Voltage: 3.3V ±10%
ÎÎPackaging:
20-TQFN (4x4mm)
In addition to signal conditioning, when EN = 0, the device
enters a low power standby mode.
Applications
ÎÎNotebook, desktop, docking station, Set Top Box, Server
Workstation, Data Storage
Pin Diagram (Top Side View)
Block Diagram
TDet#
NC
A_EQ
TDeT_EN
B_EQ
VDD
Signal Detection
CML
20 19 18 17 16
AI+
1
AI-
2
TDet_B#
3
BOBO+
15
AO-
13
TDet_A#
4
12
BI-
5
11
6 7 8 9 10
BI+
50Ω
CML
Equalizer
xO+
Limiting
Amp
xO-
xl-
- Repeated 2 times -
VDD
A_EM
B_EM
EN
NC
50Ω
xl+
AO+
14
GND
VBIAS = 1.05V
EN
Power
Management
Control
Circuit
x_EQ
x_EM
TDet_EN
All trademarks are property of their respective owners.
14-0128
1
www.pericom.com08/25/14
PI3EQX6741ST
3.3V, 1-Port, SATA3i ReDriver™
Pin Description
Standard
Mode
Pin #
Pin Name
Type
Description
9
A_EM
Input
Output emphasis adjustment for channel A. (See Configuration Table)
Digital control with 200KΩ pull-up resistor.
17
A_EQ
Input
Channel A Equalization adjustment is active. (See Configuration Table)
Tri-level input pin with 100KΩ pull-up and 100KΩ pull-down resistors.
1
2
AI+
AI-
Input
CML input forward channel A with internal 50Ω pull-up resistors connected to VBIAS (100Ω
differential).
15
14
AO+
AO-
Output
8
B_EM
Input
Output emphasis adjustment for channel B. (See Configuration Table)
Digital control with 200KΩ pull-up resistor.
19
B_EQ
Input
Tri-level input pin with 100KΩ pull-up and 100KΩ pull-down resistors. (See Configuration
Table)
11
12
BI+
BI-
Input
CML input return channel B with internal 50KΩ pull-up, resistor connected to VBIAS (100Ω
differential).
5
4
BO+
BO-
Output
Positive CML output channel B with internal 50Ω pull-up resistor connected to VBIAS (100Ω
differential).
7
EN
Input
Chip Enable "High" provides normal operation. "Low" for power down mode. With internal
200KΩ pull-up resistor.
Center
Pad
GND
GND
Supply ground.
10, 20
VDD
Power
3.3V supply voltage ± 10%
3
TDet_B#
Output
Termination detect output for channel B-Active Low, open drain. Low: HDD Termination
present. High: HDD Termination NOT present.
13
TDet_A#
Output
Termination detect output for channel A-Active Low, open drain. Low: HDD Termination
present. High: HDD Termination NOT present.
CML output channel A with internal 50Ω pull-up resistors connected to VBIAS (100Ω
differential).
Termination Detect Enable (200KΩ internal pull-up resistor)
18
TDet_EN Input
High: Enable Termination Detect for eSATA application or hot plug Device application
Low: Disable Termination Detect for internal SATA application.
6, 16
NC
No Connection internally.
All trademarks are property of their respective owners.
14-0128
2
www.pericom.com08/25/14
PI3EQX6741ST
3.3V, 1-Port, SATA3i ReDriver™
Configuration Table - Output Pre-emphasis/Swing Setting
A_EM/B_EM
3 Gb/s
6 Gb/s
0
550mV pp
650mV pp
1
550mV pp + 3dB Pre-emphasis
650mV pp + 1.5dB Pre-emphasis
Configuration Table - Input Equalizer
A_EQ/B_EQ
1.5 Gb/s
3 Gb/s
6Gb/s
0
1 dB
2.5 dB
3 dB
floating
2.5 dB
5 dB
6 dB
1
4 dB
7.5 dB
9 dB
Termination Detect Feature:
Termination Detect is a power saving feature. The user can enable TDet_EN (set to High) for eSATA application as it would save
more power when there is no external HDD connection. But for internal SATA application, TDet_EN should be set to LOW because
internal HDD is always on and termination is always there.
When Redriver doesn’t detect Host or HDD termination, there will be about 12us detect pulse width with 50us detect period at
the output of ReDriver. Once the termination is detected, the detect period will change to about 40ms. Anyway when the signal is
detected at the input of redriver, there will not be any detect pulse at both the output side of redriver.
All trademarks are property of their respective owners.
14-0128
3
www.pericom.com08/25/14
PI3EQX6741ST
3.3V, 1-Port, SATA3i ReDriver™
Maximum Ratings
(Above which useful life may be impaired. For user guidelines, not tested.)
Note:
Storage Temperature.................................................–65°C to +150°C
Supply Voltage to Ground Potential......................... –0.5V to +4.6V
DC SIG Voltage..................................................–0.5V to VDD +0.5V
Current Output ...................................................... -25mA to +25mA
Power Dissipation Continuous.............................................. 500mW
Operating Temperature......................................................0 to +70°C
Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at
these or any other conditions above those indicated in the
operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended
periods may affect reliability.
ESD, Human Body Model...............................................-8kV to 8kV
AC/DC Electrical Characteristics
Symbol
Parameter
Conditions
Min.
Typ.(1) Max.
VDD
Power Supply Voltage
PSTANDBY
Supply Power, Standby
EN = 0
0.07
0.7
PUNPLUG
Supply Power, HDD unplugged
No HDD attached, TDet_EN = High
3.6
11
PSLUMBER
Supply Power, Slumber
TDet_EN = Low
36
50
PACTIVE
Supply Power, Active
EN = 1 A/B_EM=0
DIFFP-P ≥ VTH-SD
254
317
IDD-STANDBY
Supply Current Standby
EN = 0
0.02
0.2
IDD-UNPLUG
Supply Current, HDD unplugged
No HDD attached, TDet_EN = High
1
3
IDD-SLUMBER
Supply Current Slumber
TDet_EN = Low
11
14
IDD-ACTIVE
Supply Current Active
77
88
tPD
Latency
3.0
EN = 1, input = 600mVppd,
A/B_EM=0
From input to output
3.6
0.7
Units
V
mW
mA
ns
CML Receiver Input
ZRX-DC
DC Input Impedance
40
50
60
ZRX-DIFF-DC
DC Differential Input
Impedance
80
100
120
VRX-DIFFp-p
Differential Input Peak-to-peak
Voltage
0.2
VRX-CM-ACP
AC Peak Common Mode Input
Voltage
VTH-SD
Signal detect Threshold
EN = 1
50
Ohm
1.2
V
150
mV
200(2)
mVppd
Note:
1. Typical values are at V DD = 3.3V, TA = 25°C ambient and maximum loading.
2. Using Compliance test at 1.5Gbps, 3Gbps and 6Gbps. Also using OOB (OOB is formed by ALIGNp primitive or D24.3) test patterns at 1.5Gbps.
The ALIGN primitive (K28.5+D10.2+D27.3 = 0011111010+0101010101+0010011100). The D24.3 = 00110011001100110011.
All trademarks are property of their respective owners.
14-0128
4
www.pericom.com08/25/14
PI3EQX6741ST
3.3V, 1-Port, SATA3i ReDriver™
AC/DC Electrical Characteristics (CML Receiver Input continued)
Symbol
RLdd11_RX
RLcc11_RX
RLdc11_RX
Parameter
Conditions
Min.(1) Typ.(1) Max.
Units
RX differential mode return loss
75MHz-300MHz
300MHz-600MHz
600MHz-1.2GHz
1.2GHz-2.4GHz
2.4GHz-3.0GHz
3.0 GHz-5.0GHz
18
14
10
8
3
1
dB
RX common mode return loss
150MHz – 300MHz
300MHZ – 600MHz
600MHz – 1.2GHz
1.2GHz – 2.4GHz
2.4GHz – 3.0GHz
3.0GHz – 5.0GHz
3
5
2
2
1
1
dB
RX impedance balance
150MHz – 300MHz
300MHz – 600MHz
600MHz – 1.2GHz
1.2GHz – 2.4GHz
2.4GHz – 3.0GHz
3.0GHz – 5.0GHz
30
30
20
10
4
4
dB
CML Transmitter Output (100Ω differential)(3)
ZTX-DIFF-DC
DC Differential TX Impedance
80
VTX-DIFFp-p
Differential Peak-to-peak Output
Voltage
VTX-DIFFp-p = 2
* | VTX-D
VTX-C
Common-Mode Voltage
tF, tR
100
120
Ohm
SATA2
450
700
SATA3
550
750
mV
| VTX-D+ + VTX-D-|/2
0.5
1.2
V
Transition Time
20% to 80% (3)
50
150
ps
Vamp_bal
TX amplitude imbalance
3G only; HFTP, MFTP
10
%
Tskew
TX differential skew
1.5G and 3G; HFTP, MFTP
20
ps
Vcm_ac
TX AC common mode voltage
3G only; MFTP
50
mVpp
3
VTX-Pre-Ratio-max Max TX Pre-emphasis Level
dB
1.5
150MHz – 300MHz
300MHz – 600MHz
600MHz – 1.2GHz
1.2GHz – 2.4GHz
2.4GHz – 3.0GHz
3.0 GHz – 5.0GHz
RLdd11_TX
TX differential mode return loss
CTX
AC Coupling Capacitor
TJ
Total Jitter
FR4 Input Trace
DJ
Deterministic Jitter
FR4 Input Trace
14
8
6
6
3
1
2
dB
4.7
12
18"
0.16
36"
0.24
18"
0.11
36"
0.19
nF
UI
UI
Note:
3. Recommended output coupling capacitor is 4.7nF to 12nF (on each output)
All trademarks are property of their respective owners.
14-0128
5
www.pericom.com08/25/14
PI3EQX6741ST
3.3V, 1-Port, SATA3i ReDriver™
AC/DC Electrical Characteristics
Symbol
RLcc11_TX
RLdc11_TX
Parameter
Conditions
Min.
Typ.(1) Max.
Units
TX common mode return loss
150MHz – 300MHz
300MHz – 600MHz
600MHz – 1.2GHz
1.2GHz – 2.4GHz
2.4GHz – 3.0GHz
3.0 GHz – 5.0GHz
5
5
2
2
1
1
dB
TX impedance balance
150MHz – 300MHz
300MHz – 600MHz
600MHz – 1.2GHz
1.2GHz – 2.4GHz
2.4GHz – 3.0GHz
3.0 GHz – 5.0GHz
30
20
10
10
4
4
dB
LVCMOS Control Pins
0.65 ×
VDD
VIH
Input High Voltage (Bi-Level)
VIL
Input Low Voltage (Bi-Level)
0.35 ×
VDD
IIH
Input High Current
100
IIL
Input Low Current
VOL
DC Output Logic Low
VIH
Input High Voltage (Tri-Level)
VIL
Input Low Voltage (Tri-Level)
-100
IOL = 4 mA
0.4
0.8
×VDD
V
µA
V
V
0.2 ×
VDD
V
Auto Slumber Mode Entry/Exit Time
Symbol
Parameter
Conditions
TSlumberON
Entry time to Slumber Mode
TSlumberOFF
Exit time from Slumber Mode
All trademarks are property of their respective owners.
14-0128
Typ.(1) Max.
Units
Electrical Idle at Input (See Figure)
10
20
µS
After first signal activity (See Figure)
6
20
ns
6
Min.
www.pericom.com08/25/14
PI3EQX6741ST
3.3V, 1-Port, SATA3i ReDriver™
Pre-emphasis = 20.Log(VDIFF-PRE/VDIFF)
VD+
Common Mode
Voltage
VCM
VDIFF
V D+
VD-
VDIFFp-p
V_D+ - V_D-
V CM
VDIFF-PRE
VDIFF
V D0V
VDIFFp-p
2nd + TBIT(s)
1st TBIT
Definition of Differential Voltage
and Differential Voltage Peak-to-Peak
Definition of Pre-emphasis
FR4
Signal
Source
A
B
C
D.U.T.
SmA
Connector
SmA
Connector
In
Out
30IN
Test Condition Referenced in the Electrical Characteristic Table
Auto Slumber Mode Entry and Exit Timing
All trademarks are property of their respective owners.
14-0128
7
www.pericom.com08/25/14
PI3EQX6741ST
3.3V, 1-Port, SATA3i ReDriver™
Application Schematic
VDD
VDD
*R1
*R1
*R2
*R2
SATA HOST Application
20
19
18
T_Det_EN
17
A_EQ
16
NC
VDD
AI-
TDetB#
AOBIBI+
*R2
NC
100k
Note:
* Connect R1 for HIGH
Connect R2 for LOW
Don’t connect R1, R2 for mid level.
R1, R2 are 0Ω resistors.
14-0128
20
19
18
T_Det_EN
17
A_EQ
16
NC
AI+
AI-
TDetB#
SATA Device Application
PI3EQX6741ST
15
14
13
TDetA#
12
BI11
BI+
GND
BO-
AO+
AO-
VDD
B_EM
BO+
A_EM
Device VDD
VDD
1
2
3
4
5
B_EQ
C12
*R2
EN
C11
10n
*R1
*R2
+2.5 ~ +3.3V
R5
All trademarks are property of their respective owners.
*R1
NC
WATF-07
VDD
C14
C16
4.7nf
4.7nf
C18
C20
4.7nf
4.7nf
DEVICE
Device EN
6
7
8
9
10
4.7nf
4.7nf
10n
+2.5 ~ +3.3V
C17
C19
4.7nf
4.7nf
J2
1
2
3
4
5
6
7
*R1
VDD
4.7nf
4.7nf
C8
C10
1
2
3
4
5
6
7
VDD
VDD
*R2
C13
C15
4.7nf
4.7nf
WATF-07
DEVICE
*R1
1
2
3
4
5
6
7
C4
C6
6
7
8
9
10
R2
100k
J5
1
2
3
4
5
6
7
15
14
13
12
11
VDD
BO+
HOST VDD
HOST
AO+
TDetA#
GND
BO-
B_EM
C1
4.7nf
4.7nxf
AI+
B_EQ
C1
10n
1
2
3
4
5
4.7nf
4.7nf
A_EM
HOST
C7
C9
PI3EQX6741ST
+2.5 ~ +3.3V
EN
C3
C5
10n
+2.5 ~ +3.3V
VDD
VDD
*R1
*R1
*R2
*R2
8
www.pericom.com08/25/14
PI3EQX6741ST
3.3V, 1-Port, SATA3i ReDriver™
Packaging Mechanical: 20-contact TQFN (ZD)
1
DATE: 09/11/08
DESCRIPTION: 20-Lead, Thin Fine Pitch Quad Flat No-Lead (TQFN)
PACKAGE CODE:
ZD20
DOCUMENT CONTROL #: PD-2084
REVISION: --
08-0456
Note: For latest package info, please check: http://www.pericom.com/products/packaging/mechanicals.php
Ordering Information
Ordering Number
Package Code
Package Description
PI3EQX6741STZDE
ZD
20-Lead, Thin Fine Pitch Quad Flat No-Lead (TQFN) 4x4mm
Notes:
• Thermal characteristics can be found on the company web site at www.pericom.com/packaging/
• E = Pb-free and Green
• X suffix = Tape/Reel
All trademarks are property of their respective owners.
14-0128
9
www.pericom.com08/25/14