Preliminary PT1621 RAM Mapping 32 x 4 LCD Controller DESCRIPTION The PT1621 is a RAM mapping, 128 dots (32x4) and multi-function LCD driver. The host can program PT1621 easily by three or four lines interface. Many S/W configuration features make PT1621 suitable for multiple LCD applications. PT1621 also includes S/W power down command to reduce power consumption. FEATURES • Operating voltage: 2.2V~5.5V • LCD operating voltage can be adjusted by VLCD pin • Built-in 256KHz RC oscillator • External 32.768KHz crystal or 256KHz frequency source input • Two selectable tone (buzzer) frequencies (2KHz/4KHz) • Built-in time base generator and WDT • • • • • • • • • • • • • • Time base or WDT overflow output 8 kinds clock sources of time base/WDT Internal LCD driving frequency source Selection of 1/2 or 1/3 bias, and selection of 1/2 or 1/3 or 1/4 duty LCD applications 32 x 4 LCD driver Built-in POR circuit Built-in 32 x 4 bit display RAM 3 or 4-wire serial interface Power down command reduces power consumption Software configuration feature Data mode and command mode instructions R/W address auto increment Three data accessing modes Package type: - PT1621-LQ: 44pin LQFP - PT1621-X: 48pin SSOP - PT1621-G: Gold bumped chip BLOCK DIAGRAM Tel: 886-66296288‧Fax: 886-29174598‧ http://www.princeton.com.tw‧2F, 233-1, Baociao Road, Sindian, Taipei 23145, Taiwan PT1621 APPLICATION CIRCUIT ORDER INFORMATION Valid Part Number PT1621-LQ PT1621-X PT1621-G PRE1.1 Package Type 44 Pins, LQFP 48 Pins, SSOP, 300MIL COG 2 Top Code PT1621-LQ PT1621-X - June 2012 PT1621 PIN CONFIGURATION 44 PINS, LQFP 48 PINS, SSOP PIN DESCRIPTION Pin Name I/O SEG7~SEG0 O CS I WR/RD CLK DATA VSS I I I/O - OSCO O OSCI VLCD VDD IRQ BZ BZ COM0~COM3 SEG31~SEG8 I O O O O O PRE1.1 Function LCD segment outputs Chip selection input with pull-high resistor. When the CS is logic high, the data and command read/write are disabled. The communication be enabled only CS is logic low. Write and read control with internal pull-high resistor Data and command write/read clock input with internal pull-high resistor. Serial data input/output with internal pull-high resistor. IC negative power supply, ground. 32.768KHz crystal oscillator for system clock. When clock set as external clock, the external clock source should be connected to the OSCI pin. The OSCI and OSCO pins can be opened when the internal RC OSC is selected. LCD power supply. IC positive power supply. Time base or WDT overflow interrupt output. (NMOS open drain output) Buzzer outputs (2KHz or 4KHz) Buzzer outputs (2KHz or 4KHz) LCD common outputs LCD segment outputs 3 Pin No. 44pin 48pin LQFP SSOP 37~44 1~8 1 9 2 3 4 5 10 11 12 13 - 14 6 7 8 9~12 13~36 15 16 17 18 19 20 21~24 25~48 June 2012 PT1621 IMPORTANT NOTICE Princeton Technology Corporation (PTC) reserves the right to make corrections, modifications, enhancements, improvements, and other changes to its products and to discontinue any product without notice at any time. PTC cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a PTC product. No circuit patent licenses are implied. Princeton Technology Corp. 2F, 233-1, Baociao Road, Sindian, Taipei 23145, Taiwan Tel: 886-2-66296288 Fax: 886-2-29174598 http://www.princeton.com.tw PRE1.1 17 June 2012