NI 6533/6534 Specifications This document lists features and specifications for the NI 6533/6534 family of devices and the NI PCI/PXI-7030/6533. The NI 6533/6534 family includes the following devices: • NI PCI-6534 • NI PXI-6534 • NI PCI-6533 (PCI-DIO-32HS) • NI PXI-6533 • NI DAQCard-6533 • NI AT-DIO-32HS Note All NI 6533/6534 devices can be programmed with NI-DAQmx or NI-DAQ Traditional (Legacy), except for the NI DAQCard-6533 and NI AT-DIO-32HS, which are only supported with NI-DAQ Traditional (Legacy). Specifications are typical at 25 °C unless otherwise noted. Specifications are subject to change without notice. For the most recent version of the specifications, visit ni.com/manuals. Digital I/O Number of channels ............................... 32 input/output; 4 dedicated output and control; 4 dedicated input and status Compatibility ......................................... TTL/CMOS (standard or open collector) Hysteresis ............................................... 500 mV Digital logic levels Level Minimum Maximum Input low voltage 0V 0.8 V Input high voltage 2V 5V Level Minimum Maximum Input low current for data lines (Vin = 0.4 V) DATA PULL† high DATA PULL low — — –70 µA –10 µA Input high current for data lines (Vin = 2.4 V) DATA PULL high DATA PULL low — — 10 µA 40 µA Input low current for control lines (Vin = 0.4 V) CTRL PULL‡ high CTRL PULL low — — –2.5 mA –200 µA Input high current for control lines (Vin = 2.4 V) CTRL PULL high CTRL PULL low — — 200 µA 1.4 mA — 4 µA Input high current for CTRL PULL/DATA PULL (Vin = 2.4 V) — 140 µA Output low voltage (IOL = 24 mA) — 0.4 V 2.4 V — Input low current for CTRL PULL/DATA PULL (Vin = 0.4 V) Output high voltage†† (IOH = 24 mA) † DATA PULL is represented as the DPULL signal in Traditional NI-DAQ (Legacy). ‡ CTRL PULL is represented as the CPULL signal in Traditional NI-DAQ (Legacy). †† When configured as active drive output terminals. Drivers configured for open-collector drive type are in the high-impedance state when at logic high level. Absolute maximum input voltage range .................................–0.3 to 5 V Power-on state for output channels ........High-impedance, pulled up or down (selectable) Pull-up/down resistors CTRL PULL (for control lines).......2.2 kΩ DATA PULL (for data lines) ..........100 kΩ Data transfers (all devices except NI DAQCard-6533).....................Interrupt, DMA NI 6533/6534 Specifications 2 ni.com Memory NI AT-DIO-32HS .................................. 16 S NI DAQCard-6533 for PCMCIA........... 16 S NI PCI/PXI-6534 ................................... 64 MB, two 32 MB modules on each NI 6534 NI PCI/PXI-7030/6533 .......................... 16 S NI PCI-DIO-32HS ................................. 16 S NI PXI-6533........................................... 16 S Sample Timing Types Sample Clock Timing1 Direction................................................. Input or output Maximum sample rate (internally timed, for small transfers2)..................... 20 MHz Minimum sample rate (internal clock rate) ................................ 1 S/10 minutes Change Detection Change-detection resolution .................. 150 ns Triggers Start and Reference3 Triggers Compatibility ......................................... TTL/CMOS Trigger types .......................................... Rising or falling edge, or digital pattern Minimum pulse width for edge triggers ..................................... 10 ns 1 Sample clock timing is described as Pattern I/O in NI-DAQ Traditional (Legacy). 2 Small transfer size is the size of the FIFO. Reference triggers are called Stop triggers in NI-DAQ Traditional (Legacy). 3 © National Instruments Corporation 3 NI 6533/6534 Specifications Pattern trigger detection capabilities ..............................................Detect pattern match or mismatch on user-selected data lines Pattern trigger resolution ........................60 ns or one Sample clock1 period, depending on pattern I/O mode RTSI Triggers (PCI, PXI, AT) Trigger lines............................................7 Bus Interfaces NI PCI-DIO-32HS/PXI-6533/ PCI-6534/PXI-6534................................PCI master and target with onboard linking (scatter-gather) DMA AT-DIO-32HS type ................................AT slave with dual DMA NI DAQCard-6533 for PCMCIA type ...PCMCIA slave Power Power Requirements +5 VDC (±5%) (with light output load) NI PCI-DIO-32HS, NI PXI-6533....1.3 A NI PCI-6534 and NI PXI-6534........2.0 A NI DAQCard-6533 for PCMCIA ....500 mA Power Available at I/O Connector NI PCI-DIO-32HS, NI PXI-6533, NI AT-DIO-32HS, NI PCI-6534, and NI PXI-6534..............+4.65 to +5.25 VDC at 1 A NI DAQCard-6533 for PCMCIA ...........+4.65 to +5.25 VDC at 250 mA 1 Sample clock is represented by the REQ signal in NI-DAQ Traditional (Legacy). NI 6533/6534 Specifications 4 ni.com Physical Dimensions, not including connectors NI DAQCard-6533 for PCMCIA ... 8.6 by 5.3 cm (3.4 by 2.1 in.) NI AT-DIO-32HS/ PCI-6533/6534................................ 17.5 by 10.7 cm (6.9 by 4.2 in.) NI PXI-6533/6534 .......................... 16.3 by 9.9 cm (6.4 by 3.9 in.) I/O connector NI PCI-DIO-32HS, NI PXI-6533, NI AT-DIO-32HS, NI PCI-6534, and NI PXI-6534............................. 68-pin male SCSI-II type NI DAQCard-6533 for PCMCIA ... 68-pin female PCMCIA connector Environment Operating temperature............................ 0 to 55 °C Storage temperature ............................... –20 to 70 °C Relative humidity ................................... 5 to 90% noncondensing Functional shock .................................... MIL-T-28800 E Class 3 (per Section 4.5.5.4.1) Half-sine shock pulse, 11 ms duration, 30 g peak, 30 shocks per face Operational random vibration (PXI only) .............................................. 5 to 500 Hz, 0.31 grms, 3 axes Nonoperational random vibration (PXI only) .............................................. 5 to 500 Hz, 2.5 grms, 3 axes Note Random vibration profiles were developed in accordance with MIL-T-28800E and MIL-STD-810E Method 514. Test levels exceed those recommended in MIL-STD-810E for Category 1 (Basic Transportation, Figures 514.4-1 through 514.4-3). © National Instruments Corporation 5 NI 6533/6534 Specifications National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation. Refer to the Terms of Use section on ni.com/legal for more information about National Instruments trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National Instruments products, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your CD, or ni.com/patents. © 2005 National Instruments Corporation. All rights reserved. 374163A-01 Nov05