NI PCI-5911 Specifications

NI PCI-5911 Specifications
High-Speed Digitizer with Flex ADC™
This document lists the specifications of the NI PCI-5911. These
specifications are typical at 25 °C unless otherwise stated. All
specifications are subject to change without notice.
Visit ni.com/manuals for the most current specifications and product
documentation.
Note
Acquisition System
Max bandwidth ...................................... 100 MHz (Refer to
NI High-Speed Digitizers Help»
Devices»NI 5911»Flexible
Resolution Mode for a table
of available sampling rates,
resolution, and corresponding
bandwidths.)
Number of channels ............................... 1
Number of flexible-resolution
A/D converters ....................................... 1
Max real-time sample rate...................... 100 MS/s
Max random interleaved sampling
(RIS) sample rate ................................... 1 GS/s
Resolution
Sample Rate
Mode
Effective Resolution
100/n* MS/s
Conventional
8 bits
12.5 MS/s
Flexible resolution
11 bits
5 MS/s
Flexible resolution
14 bits
2.5 MS/s
Flexible resolution
15.5 bits
1 MS/s
Flexible resolution
17.5 bits
500 kS/s
Flexible resolution
18 bits
200 kS/s
Flexible resolution
18.5 bits
100 kS/s
Flexible resolution
19 bits
50 kS/s
Flexible resolution
19.5 bits
20 kS/s
Flexible resolution
20.5 bits
10 kS/s
Flexible resolution
21 bits
* 1 ≤ n ≤ 224 in conventional mode
Sample onboard memory........................4 MB or 16 MB
Memory Sample Depth
Sampling
Frequency
NI PCI-5911 Specifications
Mode
Sample Depth
(4 MB)
Sample Depth
(16 MB)
100/n* MS/s
Conventional
4 MS
16 MS
12.5 MS/s
Flexible
resolution
1 MS
4 MS
5 MS/s
Flexible
resolution
1 MS
4 MS
2.5 MS/s
Flexible
resolution
1 MS
4 MS
1 MS/s
Flexible
resolution
1 MS
4 MS
500 kS/s
Flexible
resolution
1 MS
4 MS
200 kS/s
Flexible
resolution
1 MS
4 MS
2
ni.com
Sampling
Frequency
Mode
Sample Depth
(4 MB)
Sample Depth
(16 MB)
100 kS/s
Flexible
resolution
1 MS
4 MS
50 kS/s
Flexible
resolution
1 MS
4 MS
20 kS/s
Flexible
resolution
1 MS
4 MS
10 kS/s
Flexible
resolution
1 MS
4 MS
* 1 ≤ n ≤ 224 in conventional mode
Vertical Sensitivity (Input Ranges)
Input Range
Noise Referred to Input
±10 V
–174 dBfs / Hz
±5 V
–168 dBfs / Hz
±2 V
–160 dBfs / Hz
±1 V
–154 dBfs / Hz
±0.5 V
–148 dBfs / Hz
±0.2 V
–140 dBfs / Hz
±0.1 V
–128 dBfs / Hz
Acquisition Characteristics
Accuracy
DC gain accuracy ................................... ±0.05% signal ±0.0001% full
scale (fs) for all input ranges at
1 MS/s in flexible resolution
mode
DC offset accuracy................................. ±0.1 mV ±0.01% fs
for all input ranges at 1 MS/s
in flexible resolution mode
Input coupling ........................................ DC and AC, software-selectable
AC coupling cut-off frequency
(–3 dB) ................................................... 2.5 Hz ±0.5 Hz
© National Instruments Corporation
3
NI PCI-5911 Specifications
Input impedance .....................................1 MΩ ±2%
Max measurable input voltage................±10 V (DC + peak AC)
Input protection.......................................±42 VDC (DC + peak AC)
Input bias current ....................................±1 nA, typical at 25 °C
Common-Mode Characteristics
Impedance to chassis ground ..................10 kΩ
Common-mode rejection ratio................CMRR > –70 dB, (Fin < 1 kHz)
Filtering
Sampling
Frequency
Bandwidth
Ripple
Alias Attenuation
Conventional
100 MHz
±3 dB
N/A
12.5 MS/s
Flexible
Resolution
3.75 MHz
±0.2 dB
–60 dB
5 MS/s
Flexible
Resolution
2 MHz
±0.1 dB
–70 dB
2.5 MS/s
Flexible
Resolution
1 MHz
±0.05 dB
–80 dB
1 MS/s
Flexible
Resolution
400 kHz
±0.005 dB
–80 dB
500 kS/s
Flexible
Resolution
200 kHz
±0.005 dB
–80 dB
200 kS/s
Flexible
Resolution
80 kHz
±0.005 dB
–80 dB
100 kS/s
Flexible
Resolution
40 kHz
±0.005 dB
–80 dB
50 kS/s
Flexible
Resolution
20 kHz
±0.005 dB
–80 dB
20 kS/s
Flexible
Resolution
8 kHz
±0.005 dB
–80 dB
10 kS/s
Flexible
Resolution
4 kHz
±0.005 dB
–80 dB
100/n* MS/s
Filter Mode
* 1 ≤ n ≤ 224 in conventional mode
NI PCI-5911 Specifications
4
ni.com
Dynamic Range
Noise (excluding input-referred noise)
Sampling Frequency
Bandwidth
Noise Density
Total Noise
100/n* MS/s
100 MHz
–120 dBfs / Hz
–43 dBfs
12.5 MS/s
3.75 MHz
–135 dBfs / Hz
–64 dBfs
5 MS/s
2 MHz
–143 dBfs / Hz
–83 dBfs
2.5 MS/s
1 MHz
–152 dBfs / Hz
–91 dBfs
1 MS/s
400 kHz
–160 dBfs / Hz
–104 dBfs
500 kS/s
200 kHz
–160 dBfs / Hz
–107 dBfs
200 kS/s
80 kHz
–160 dBfs / Hz
–111 dBfs
100 kS/s
40 kHz
–160 dBfs / Hz
–114 dBfs
50 kS/s
20 kHz
–160 dBfs / Hz
–117 dBfs
20 kS/s
8 kHz
–160 dBfs / Hz
–121 dBfs
10 kS/s
4 kHz
–160 dBfs / Hz
–124 dBfs
* 1 ≤ n ≤ 224 in conventional mode
Distortion
Sampling
Frequency
SFDR for Input
0 dBfs
SFDR for Input
–20 dBfs
SFDR for Input
–60 dBfs (typical)
100 MS/s
50 dBfs
50 dBfs
N/A
12.5 MS/s
65 dBfs
85 dBfs
125 dBfs
5 MS/s
70 dBfs
90 dBfs
130 dBfs
2.5 MS/s
75 dBfs
95 dBfs
135 dBfs
1 MS/s
85 dBfs
105 dBfs
145 dBfs
500 kS/s
90 dBfs
110 dBfs
150 dBfs
200 kS/s
100 dBfs
110 dBfs
160 dBfs
100 kS/s
100 dBfs
110 dBfs
160 dBfs
50 kS/s
100 dBfs
110 dBfs
160 dBfs
20 kS/s
100 dBfs
110 dBfs
160 dBfs
10 kS/s
100 dBfs
110 dBfs
160 dBfs
© National Instruments Corporation
5
NI PCI-5911 Specifications
Timebase System
Reference clock ......................................10 MHz
Clock accuracy (as master).....................10 MHz ±50 ppm
Clock input tolerance (as slave)..............10 MHz ±100 ppm
Clock jitter ..............................................<75 psrms, independent of
reference clock source
Clock compatibility ................................TTL for both input and output
Sample clock frequencies
Conventional mode..........................100/n MHz, where 1 ≤ n ≤ 224
Flexible resolution mode .................12.5 MHz, 5 MHz, 2.5 MHz,
1 MHz, 500 kHz, 200 kHz,
100 kHz, 50 kHz, 20 kHz, 10 kHz
Reference clock sources .........................PFI lines, RTSI clock, or onboard
Triggering Systems
Modes .....................................................Edge, hysteresis, window, digital
Source .....................................................CH 0, RTSI<0..6>, PFI 1 (TTL),
PFI 2 (TTL)
Slope .......................................................Rising/falling
Hysteresis................................................Full-scale voltage/n, where n is
between 1 and 170
Coupling .................................................AC/DC
Pretrigger depth ......................................Up to 4 MS or 16 MS, depending
on memory option purchased and
sampling mode
Posttrigger depth.....................................Up to 4 MS or 16 MS, depending
on memory option purchased and
sampling mode
Holdoff time ...........................................5 µs to 171.79 s in 40 ns
increments
Trigger resolution ...................................170 steps in full-scale voltage
range
NI PCI-5911 Specifications
6
ni.com
Sampling Methods
RIS ......................................................... 1 GS/s down to 200 MS/s
effective sample rate, repetitive
signals only
Real-time sampling ................................ Up to 100 MS/s sample rate for
transient and repetitive signals
Power Requirements
+5 VDC .................................................. 4 A
+12 VDC ................................................ 100 mA
–12 VDC ................................................ 100 mA
Physical
Dimensions............................................. 33.8 cm by 9.9 cm
(13.3 in. by 3.9 in.)
I/O connectors
Analog input CH 0 .......................... BNC female
Digital triggers ................................ SMB jack, 9-pin mini DIN
Environmental Characteristics
Multiple NI 5911 devices in the same computer may raise operating temperatures
beyond specification and produce imprecise data. NI strongly recommends leaving an
empty PCI slot between multiple NI 5911 devices or adding a fan.
Note
Ambient temperature.............................. 5 °C to 40 °C
Relative humidity ................................... 10% to 90%, noncondensing
Storage Environment
Ambient temperature.............................. –20 °C to 65 °C
© National Instruments Corporation
7
NI PCI-5911 Specifications
Calibration
Self-calibration (internal calibration) .....Self-calibration is done using
a software command. The
calibration involves gain, offset
and linearity correction for all
input ranges and input modes.
Interval.............................................1 week, or any time temperature
changes beyond ±5 °C. Hardware
detects temperature variations
beyond calibration limits, which
also can be queried by software.
External calibration.................................Internal reference requires
recalibration
Interval.............................................1 year
Warm-up time.........................................15 minutes
Safety
This product is designed to meet the requirements of the following
standards of safety for electrical equipment for measurement, control,
and laboratory use:
•
IEC 61010-1, EN 61010-1
•
UL 3111-1, UL 61010B-1
•
CAN/CSA C22.2 No. 1010.1
Note For UL and other safety certifications, refer to the product label, or visit
ni.com/hardref.nsf, search by model number or product line, and click the
appropriate link in the Certification column.
Electromagnetic Compatibility
Emissions................................................EN 55011 Class A at 10 m
FCC Part 15A above 1 GHz
Immunity ................................................EN 61326:1997 + A2:2001,
Table 1
CE, C-Tick, and FCC Part 15 (Class A) compliant
For full EMC compliance, you must operate this device with shielded cabling.
In addition, all covers and filler panels must be installed. Refer to the Declaration of
Conformity (DoC) for this product for any additional regulatory compliance information.
Note
NI PCI-5911 Specifications
8
ni.com
To obtain the DoC for this product, visit ni.com/hardref.nsf, search by model number
or product line, and click the appropriate link in the Certification column.
CE Compliance
This product meets the essential requirements of applicable European
Directives, as amended for CE marking, as follows:
Low-Voltage Directive (safety) ............. 73/23/EEC
Electromagnetic Compatibility
Directive (EMC) .................................... 89/336/EEC
Refer to the Declaration of Conformity (DoC) for this product for any additional
regulatory compliance information. To obtain the DoC for this product, visit
ni.com/hardref.nsf, search by model number or product line, and click the
appropriate link in the Certification column.
Note
© National Instruments Corporation
9
NI PCI-5911 Specifications
Flex ADC™, National Instruments™, NI™, ni.com™, and RTSI™ are trademarks of National Instruments
Corporation. Product and company names mentioned herein are trademarks or trade names of their
respective companies. For patents covering National Instruments products, refer to the appropriate
location: Help»Patents in your software, the patents.txt file on your CD, or ni.com/patents.
© 2003–2004 National Instruments Corp. All rights reserved.
*323496C-01*
323496C-01
Jan04