SURFACE MOUNT RESISTOR RM Series: Thick Film INTRODUCTION 0.01~100M Ω RoHS DIMENSIONS D RFE International, Inc. offers a wide range of chip resistors to meet your application requirements. They are made with metal glazed thick film on a high purity ceramic substrate which is overcoated for stability and protection. These resistors are AEC-Q200 qualified and are suitable for all applications (automotive, lighting, power, etc). • Lower & Ηigher values see additional RM Series • Anti-Sulfur Thick Film see RMS Series • High Power Thick Film see RMH Series • Anti-Sulfur High Power see RMP Series • Thin Film see RMT Series • Fusible Resistors see RMF Series • Thick Film Array Chip see RCN Series • Metal Array Low-Resistance see LR Series PART NUMBER EXAMPLE Glass Passivation H W C L Max. Dimension (mm) Size Code RM02 (0201) RM04 (0402) RM06 (0603) RM10 (0805) RM12 (1206) RM25 (1210) RM50 (2010) RM50S (1812) RM1W (2512) RM1WS (1218) RM2W (2030) L W H C D 0.60±0.03 1.00±0.10 1.60±0.20 2.00±0.20 3.05±0.10 3.05±0.10 5.00±0.20 4.50±0.10 6.30±0.20 3.10±0.10 5.10±0.10 0.30±0.03 0.50±0.05 0.80±0.15 1.25±0.15 1.60±0.20 2.50±0.20 2.50±0.20 3.00±0.10 3.20±0.20 4.60±0.10 7.60±0.10 0.23±0.05 0.30±0.05 0.40±0.10 0.50±0.15 0.55±0.15 0.55±0.15 0.55±0.10 0.55±0.05 0.55±0.10 0.55±0.05 0.60±0.05 0.15±0.05 0.15±0.10 0.20±0.10 0.30±0.15 0.40±0.20 0.50±0.20 0.60±0.20 0.55±0.20 0.60±0.20 0.40±0.20 0.80±0.20 0.15±0.05 0.15±0.10 0.20±0.10 0.40±0.15 0.50±0.20 0.50±0.20 0.60±0.20 0.70±0.20 0.60±0.20 0.50±0.20 0.80±0.20 RM 10 R - 10K - J RESISTANCE CODE Series Size Code Tolerance Code Ohms Code Resistance Code Taped & Reeled 0.0 0R0 1.0 1R0 100 100R 1.5K 1K5 15K 1.5 Meg 10 Meg 15K 1M5 10M ELECTRICAL CHARACTERISTICS & RESISTANCE RANGE Code RM02 RM04 RM06 RM10 RM12 RM25 RM50 RM50S RM1W RM1WS RM2W Size (0201) (0402) (0603) (0805) (1206) (1210) (2010) (1812) (2512) (1218) (2030) Rated Power at 70°C Max. Working Voltage 0.05W 25V 0.063W 0.10W 0.125W 0.25W 0.33W 0.50W 0.50W 1.0W 1.0W 2.0W 50V 50V 150V 200V 200V 200V 200V 250V 250V 250V Max. Overload Voltage 50V 100V 100V 300V 400V 400V 400V 400V 500V 500V 500V Resistance Range T.C.R. (PPM/°C) B (±0.1%) D (±0.5%) F (±1%) J (±5%) ±200 10Ω ~ 1MΩ 10Ω ~ 1MΩ 0 ~ +400 ±300 ±200 ±400 ±200 ±100 ±400 ±200 ±100 ±400 ±200 ±100 ±400 ±200 ±100 ±400 ±200 ±100 ±400 ±200 ±100 ±400 ±200 ±100 ±400 ±200 ±100 ±400 ±200 1Ω ~ 9.9Ω 10Ω ~ 990Ω 1KΩ ~ 10MΩ 1Ω ~ 9.9Ω 1Ω ~ 9.9Ω 10Ω ~ 990Ω 1KΩ ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ ±100 10Ω ~ 1MΩ 10Ω ~ 1MΩ 10Ω ~ 1MΩ 10Ω ~ 1MΩ 10Ω ~ 1MΩ 10Ω ~ 1MΩ 10Ω ~ 1MΩ 10Ω ~ 1MΩ 10Ω ~ 1MΩ 10Ω ~ 1MΩ 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 10Ω ~ 10MΩ Page 1 of 5 RFE International • Tel:(949) 833-1988 • Fax:(949) 833-1788 • E-Mail [email protected] C2BB01 2015.02.17 SURFACE MOUNT RESISTOR RM Series: Thick Film 0.01~100M Ω RoHS ELECTRICAL CHARACTERISTICS & RESISTANCE RANGE (CONTINUE) RATINGS FOR LOW RESISTANCE <1 TYPE Rated Max Working Power at Voltage 70°C RM04 (0402) 0.063 W RM06 (0603) 0.1 W RM10 (0805) RM12 (1206) RM25 (1210) RM50 (2010) RM50S (1812) RM1W (2512) RM1WS (1218) 0.125 W 0.25 W 0.33 W 0.5 W 0.5 W 1W 1W Max Overload Voltage T.C.R. (PPM/°C) Resistance Range (mΩ) F (+ 1%, J (+ 5%) 0.25 V 0.624 V + 800 470 ~ 990 + 800 100 ~ 330 0.31 V 0.775 V + 600 331 ~ 550 + 400 511 ~ 990 0.35 V 0.875 V 0.5 V 0.57 V 1.25 V 1.425 V 0.7 V 1.75 V 0.7 V 0.99 V 0.99 V 1.75 V 2.475V 2.475V + 1000 10 ~ 50 + 800 51 ~ 100 + 600 101 ~ 330 + 400 331 ~ 990 + 800 10 ~ 50 + 600 51 ~ 100 + 500 101 ~ 330 + 400 331 ~ 990 + 800 10 ~ 50 + 600 51 ~ 100 + 500 101 ~ 330 + 400 331 ~ 990 + 800 10 ~ 50 + 800 51 ~ 100 + 600 101 ~ 330 + 400 331 ~ 990 + 800 10 ~ 50 + 600 51 ~ 100 + 500 101 ~ 330 + 400 331 ~ 990 + 800 10 ~ 50 + 700 51 ~ 100 + 500 101 ~ 330 + 400 331 ~ 990 + 800 10 ~ 50 + 400 51 ~ 990 RATINGS FOR HIGH RESISTANCE >10Meg TYPE Rated Max Max Power at Working Overload 70°C Voltage Voltage RM04 (0402) 0.063 W 50V 100V RM06 (0603) 0.1 W 50V 100V RM10 (0805) 0.125 W 150V 300V RM12 (1206) 0.25 W 200V 400V RM25 (1210) 0.33 W 200V 400V RM50 (2010) 0.5 W 200V 400V RM1W (2512 1W 200V 400V RM1WS (1218) 1W 200V 400V T.C.R. (PPM/°C) + 200 Resistance Range (mΩ) F (+ 1%) J (+ 5%) 10.1 MΩ ~ 54 MΩ 10.1 MΩ ~ 100 MΩ Page 2 of 5 RFE International • Tel:(949) 833-1988 • Fax:(949) 833-1788 • E-Mail [email protected] C2BB01 2015.02.17 SURFACE MOUNT RESISTOR RM Series: Thick Film 0.01~100M Ω RoHS PERORMANCE CHARACTERISTICS Operating Temperature Range -55°C to +155°C Power Derating Curve Power Ratio (%) 100 80 1 60 40 155°C 1 20 1 0 -55 0 20 40 60 70 80 100 120 140 160 Ambient Temperature (°) Power rating or current rating is in the case based on continuous full-load at ambient temperature of 70ºC. For operation at ambient temperature in excess of 70ºC, the load should be derated in accordance with figure of derating Curve. Voltage Rating or Current Rating Resistance Range: >1Ω Rated Voltage: The resistor shall have a DC continuous working voltage or a RMS AC continuous working voltage at commercial-line frequency and wave form corresponding to the power rating, as determined formula as follows: E = Rated Voltage (V) P = Power Rating (W) R = Nominal Resistance (Ω) E = √P x R Operation and Storage Temperature TYPE MIN MAX -55ºC 70ºC Storage temperature 20ºC 30ºC Storage humidity 30% 70ºC Operation temperature Soldering Profile +5 250 Peak: 250 0 ºC 230ºC or Higher 1 200 180ºC Pre Heating Zone 1 150 150ºC 90 ± 30 s 1 30 ± 10 s 100 Soldering Zone 1 50 Heating Time Page 3 of 5 RFE International • Tel:(949) 833-1988 • Fax:(949) 833-1788 • E-Mail [email protected] C2BB01 2015.02.17 SURFACE MOUNT RESISTOR RM Series: Thick Film 0.01~100M Ω RoHS TEST PROCEDURES & REQUIREMENTS Test Item Procedure Test Method Requirements Temperature JIS C 5201-1 Coefficient of Resistance (T.C.R.) Clause 4.8 -55°C ~ +155°C, 20°C is the reference temperature Refer to Ratings Short Time Overload General: 2.5 times RCWV or Max. Overload voltage for 5 seconds High Power: 2.5 times RCWV or Max. Overload voltage for 2 seconds ±1: ±(1.0%+0.05Ω) ±5: ±(2.0%+0.1Ω) JIS C 5201-1 Clause 4.13 +5 250 Peak: 250 0 ºC 230ºC or Higher 1 200 180ºC Pre Heating Zone 1 150 IR Reflow Sony SS-00254 1 100 150ºC 30 + 10 s Soldering Zone 1 50 ±1: ±(1.0%+0.05Ω) ±5: ±(2.0%+0.1Ω) 90 + 30 s Heating Time Leaching Sony SS-00254-9 260 ±5°C for 30 seconds > 95% Coverage Soldering Heat JIS C 5201-1 Clause 4.18 260 ±5°C for 10 seconds ±1: ±(0.5%+0.05Ω) ±5: ±(1.0%+0.05Ω) Temperature Cycling JIS C 5201-1 Clause 4.19 -55°C ~ +155°C, 5 cycles 0.1% ' 0.5% ' 1% ±(0.5%+0.05Ω) 2% ' 5% ±(1.0%+0.1Ω) Electric Iron Sony SS-00254-5 Preheating termperature: 350 ± 5°C Electric Iron preheating time: 3 +1/-0 sec. ±1: ±(0.5%+0.05Ω) ±5: ±(1.0%+0.05Ω) Resistance to Solvent JIS C 5201-1 Clause 4.29 The tested resistor be immersed into isopropyl alcoho of 20~25°C for 60 seconds. Then the resistor is left in the room for 48 hours. ±1: ±(0.5%+0.05Ω) ±5: ±(1.0%+0.05Ω) Load Life in Humidity JIS C 5201-1 Clause 4.24 40 ± 2°C, 90~95% R.H. or Max. working voltage for 1000 hours with 1.5 hrs “ON” and 0.5hr “OFF”. 0.1% ' 0.5% ' 1% ±(0.5%+0.05Ω) 2% ' 5% ±(3.0%+0.1Ω) Load Life (Endurance) JIS C 5201-1 Clause 4.25 70 ± 2°C, or Max. working voltage for 1000 hours with 1.5 hrs “ON” and 0.5hr “OFF”. 0.1% ' 0.5% ' 1% ±(1.0%+0.05Ω) 2% ' 5% ±(3.0%+0.1Ω) Terminal Bending Strength JIS C 5201-1 Clause 4.33 Bending once for 5 seconds D: RM Series 0402 ' 0603 ' 0805 = 5mm RM Series 1206 ' 1210 ' 1812 = 3mm RM Series 1218 ' 2010 ' 2512 ' 2030 = 2mm ±1: ±(1.0%+0.05Ω) ±5: ±(1.0%+0.05Ω) Insulation Resistance JIS C 5201-1 Clause 4.6 Max Overload Voltage for 1 min. ≥ 10G Page 4 of 5 RFE International • Tel:(949) 833-1988 • Fax:(949) 833-1788 • E-Mail [email protected] C2BB01 2015.02.17 SURFACE MOUNT RESISTOR RM Series: Thick Film 0.01~100M Ω RoHS PACKAGE & DIMENSION (mm) Package Q’ty Size A ØB ØC ØD W ØM 10K/reel 2.0±0.5 13.5±1.0 21±1.0 60±1.0 11.5±2.0 178±2.0 7” 5K/reel 2.0±0.5 13.5±1.0 21±1.0 60±1.0 11.5±2.0 178±2.0 10” 10K/reel 2.0±0.5 13.5±1.0 21±1.0 100±1.0 11.5±2.0 254±2.0 13” 20K/reel 2.0±0.5 13.5±1.0 21±1.0 100±1.0 11.5±2.0 330±2.0 7” 5K/reel 2.0±0.5 13.5±1.0 21±1.0 60±1.0 11.5±2.0 178±2.0 7” 4K/reel 2.0±0.5 13.5±1.0 21±1.0 60±1.0 16.0±2.0 178±2.0 7” 1K/reel 2.0±0.5 13.5±1.0 21±1.0 60±1.0 19.0±2.0 178±2.0 RM02(0201) RM04(0402) 7” RM06(0603) RM10(0805) RM12(1206) RM25(1210) RM50(2010) RM50S(1812) RM1W(2512) RM1WS(1218) RM2W(2030) TAPING SPECIFICATION Paper Type (P= 2.0 ± 0.1) Size A B W E F G H T ØD RM02(0201) 0.45±0.10 0.75±0.10 8.0±0.20 1.75±0.10 3.5±0.05 4.0±0.10 2.0±0.05 0.35±0.10 1.50±0.10 RM04(0402) 0.70±0.10 1.20±0.10 8.0±0.20 1.75±0.10 3.5±0.05 4.0±0.10 2.0±0.05 0.45±0.10 1.50±0.10 RM06(0603) RM10(0805) RM12(1206) RM25(1210) 1.05±0.20 1.80±0.20 1.55±0.20 1.90±0.20 2.30±0.20 3.50±0.20 3.5±0.05 3.5±0.05 3.5±0.05 3.5±0.05 2.0±0.05 2.0±0.05 2.0±0.05 2.0±0.05 0.60±0.10 0.75±0.10 0.75±0.10 1.50±0.10 1.50±0.10 1.50±0.10 3.50±0.20 1.75±0.10 1.75±0.10 1.75±0.10 1.75±0.10 4.0±0.10 4.0±0.10 4.0±0.10 2.85±0.20 8.0±0.20 8.0±0.20 8.0±0.20 8.0±0.20 0.75±0.10 1.50±0.10 4.0±0.10 Embossed Type (P= 4.0 ± 0.1) (2W.P= 8.0 ± 0.2) Size A B W E F G H T ØD ØD1 T1 RM50(2010) 2.80±0.20 5.60±0.20 12±0.10 1.75±0.10 5.5±0.05 4.0±0.10 2.0±0.05 0.23±0.10 1.50±0.10 1.50±0.10 0.85±0.15 RM50S(1812) 3.40±0.20 6.70±0.20 12±0.10 1.75±0.10 5.5±0.05 0.23±0.10 1.50±0.10 1.50±0.10 0.85±0.15 3.30±0.20 3.30±0.20 4.60±0.20 4.60±0.20 12±0.10 12±0.10 1.75±0.10 1.75±0.10 5.5±0.05 5.5±0.05 4.0±0.10 4.0±0.10 4.0±0.10 2.0±0.05 RM1W(2512) RM1WS(1218) 2.0±0.05 2.0±0.05 0.23±0.10 0.23±0.10 1.50±0.10 1.50±0.10 1.50±0.10 1.50±0.10 0.85±0.15 0.85±0.15 RM2W(2030) 5.50±0.20 7.90±0.20 16±0.10 1.75±0.10 7.5±0.05 4.0±0.10 2.0±0.05 0.23±0.10 1.50±0.10 1.50±0.10 0.85±0.15 Page 5 of 5 RFE International • Tel:(949) 833-1988 • Fax:(949) 833-1788 • E-Mail [email protected] C2BB01 2015.02.17