F E D C B A n1,8 (3x) (5:1) D 0,12 14,23 +- 0,38 D SEALING COMPOUND 47,7 +- 0,3 0 33,3 +- 0,15 0,1 21,1 +- 00,3 3,6 +- 0,25 0 A1 C 0,17 5,7 +- 0,08 25,17 +- 0,2 0,05 8,26 +- 0,22 0,03 RUBBER GASKET PLACED ON TOP SURFACE OF MALE INSULATOR 10° C SW 4,8 9,4 4,6 4-40 UNC 4-40 UNC O-RING 6,1 see note 8 6003W3PXX61B50X CONEC ABC B 4-40 UNC B NOTES: see note 13 n4 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 2. METALSHELLS: COPPER ALLOY; min. 315µin TIN over 40-80µin NICKEL 3. INSULATOR: PBT GF UL 94 V-0, GREEN 4. HIGH POWER CONTACTS 10A: COPPER ALLOY PLATING MATING AREA: 8µin HARD GOLD over min. 50µin NICKEL PLATING TERMINATION SIDE: 8µin HARD GOLD over min. 50µin NICKEL SOLDER CUP ACCEPTS CABLE AWG 16-20 5. THREADED LOCKS: COPPER ALLOY; min. 200µin TIN over 80µin NICKEL 6. COLLARS: COPPER ALLOY; min. 200µin TIN over 80µin NICKEL 7. HEXLOCKING SCREWS: STAINLESS STEEL 8. FRAME: ZINC DIE CAST; NICKEL PLATED 9. O-RING: SILICON; BLUE 10. RUBBER GASKET: TPE; BLACK 11. RECOMMENDED PANEL CUTOUT ON SHEET 2 12. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3,1 in.LB) / max. 40Ncm (3,5 in.LB) 13. CONNECTOR IS PART MARKED: 6003W3PXX61B50X CONEC ABC TITLE: COMPANY NAME: APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION # APPROVAL F E DO NOT ALTER CAD DRAWING BY HAND NAME: THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION # APPROVAL CUSTOMER APPROVAL DATE: APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION A APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. tolerance dim. in mm scale: material: A title: name drawn 07.06.10 Schmidt D-SUB COMBINATION MALE appd. 07.06.10 Fischer 3W3P SOLDER CUP with threaded lock and hexlocking screw dwg no: Inventor 10 DIN- d-old Origin rev. description date part no: name C A3 sh: 1 15K1A656 R D see notes date norm a 2:1 (5:1) B 6003W3PXX61B50X A F E D C B A D D Solder Instruction 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Operate the soldering iron at 350°C, 100 Watt max. and use a pencil tip. 4. Put tip to wire in solder cup. 5. After 1 second bring in solder. 6. Heat for 5 seconds longer. Do not heat contact more than 6 seconds in total. 7. Remove soldering iron. 8. Wait until solder gets rigid again. 9. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up. C C RECOMMENDED PANEL CUT-OUT 33,3 `0,1 + 0,1 n2,8 - 0 (2x) i 0,20 A B 13 `0,1 B A 29,2 `0,1 ,1 ` 0, 13 B TITLE: COMPANY NAME: APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION # APPROVAL F E DO NOT ALTER CAD DRAWING BY HAND NAME: THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION # APPROVAL CUSTOMER APPROVAL DATE: APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION A APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION R2 i 0,20 B tolerance dim. in mm scale: material: A title: date name drawn 07.06.10 Schmidt PANEL CUTOUT appd. 07.06.10 Fischer D-SUB COM. MALE 3W3P SOLDER CUP with threaded lock and hexlocking screw dwg no: Inventor 10 DIN- norm d-old Origin rev. description D date part no: name C A3 sh: 2 15K1A656 R a 4:1 see sheet 1 B see sheet 1 A