F E D C B A b NOTES: (5:1) D 10,31 +- 0,4 0,3 D n1,12 (15x) 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI FOR 30 MINUTES AFTER SOLDERING 4. METALSHELL: ZINC DIE CAST; min. 50µin NICKEL PLATING over COPPER 5. INSULATORS: PBT GF UL 94 V-0, BLACK 6. O-RING: SILICONE PER ASTM D2000 70 SHORE A 7. RUBBER GASKET: TPE 8. SEALING COMPOUND: EPOXY RESIN UL 94 V-0; BLACK 9. CONTACTS: COPPER ALLOY PLATING (SEE PART NO): o PLEASE ADD 1 for 30µin HARD GOLD over min. 50µin NICKEL o PLEASE ADD 3 for 8µin HARD GOLD over min. 50µin NICKEL SOLDER CUP ACCEPTS CABLE AWG 20 10. HEXLOCKING SCREWS: STAINLESS STEEL 11. RECOMMENDED PANEL CUT-OUT ON SHEET 2 12. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max.67Ncm (6 in.LB) 13. CONNECTOR IS PART MARKED: 15-00058o CONEC ABC 3,6 +- 0,25 0 0,12 6 +- 0,18 c 8,23 +- 0,25 0 47,7 +- 0,3 0 RUBBER GASKET PLACED ON TOP SURFACE OF MALE INSULATOR 33,32 +- 0,13 0,12 POS. 1 C c 25,14 +- 0,23 0,02 21,1 +- 0,3 0 POS. 9 C 10° SEALING COMPOUND 15-00058o CONEC ABC O-RING B B 4,6 4-40 UNC b 9,4 SEE NOTE 13 SW 4,8 4-40 UNC c TITLE: COMPANY NAME: APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION # APPROVAL F E DO NOT ALTER CAD DRAWING BY HAND NAME: THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION # APPROVAL CUSTOMER APPROVAL DATE: APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION A APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. tolerance dim. in mm scale: material: Ä 3435 29.09.09 HS 3xb Ä 3129 26.09.08 HS a Origin rev. description D A title: name drawn 03.09.08 Schmidt D-SUB MALE appd. 15.09.08 Fischer 15pos. SOLDER CUP with hexlocking screw dwg no: d-old part no: name C DINA3 sh: 1 Inventor 10 15K1A261 R date see notes date norm 3xc 2:1 (5:1) B 15-00058o (see note 9) b A F E D C B A b Solder Instruction D D 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Operate the soldering iron at 350°C, 50 Watt max. and use a pencil tip. 4. Put tip to wire in solder cup. 5. After 1 second bring in solder. 6. Heat for 3 seconds longer. Do not heat contact more than 4 seconds in total. 7. Remove soldering iron. 8. Wait until solder gets rigid again. 9. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up. C C RECOMMENDED PANEL CUT-OUT b 28,8 `0,1 i 0,26 A 11,4 `0,1 B ,4 ` R3 n3,1 `0,05 (2x) B 10° `1° B i 0,26 B 3 0,1 TITLE: COMPANY NAME: APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION # APPROVAL F E DO NOT ALTER CAD DRAWING BY HAND NAME: THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION # APPROVAL CUSTOMER APPROVAL DATE: APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION A APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION 33,32 `0,1 A tolerance dim. in mm date name drawn 03.09.08 Schmidt appd. 15.09.08 Fischer a Origin rev. description D 26.09.08 HS R date A PANEL CUT-OUT d-old Ä 3129 D-SUB MALE 15pos. SOLDER CUP with hexlocking screw dwg no: Inventor 10 DINA3 15K1A261 sh: 2 part no: name C 5:1 see sheet 1 title: norm 2xb scale: material: B see sheet 1 A