Trap Series Technologically Advanced: Features: Waterproof Receiver IP68 2Km Range One Transmitter to Many receivers Protective Rubber Boot Robust and reliable 1, 4 and 16 Switch versions Description The TRAP system delivers reliable operation 365 days of the year. This rugged professional system is designed to meet the heavy usage needs associated with club traps. Each receiver has four independent outputs which can easily be paired with individual switches from one or many different transmitters. Building a bespoke control system is easy with transmitters containing up to 16 switches. DS-TRAP-3 Trap remote control system System part numbers Part Number Description TRAP-S1 Single channel system Part Number Description TRAP-S4 Four channel system Additional transmitters SABRE Transmitters are available individually with 1, 3 or 8 buttons and can be configured to work any Part Number Description TRAP-T1 Transmitter 1 switch TRAP-T2 Transmitter 2 switch TRAP-T4 Transmitter 4 switch TRAP-T16 Transmitter 16 switch Additional receivers These can be used with any existing TRAP transmitter or SABRE transmitter Part Number Description TRAP-RX Receiver Unit. DS-TRAP-3 PAGE 2 Trap remote control system Connecting the receiver unit. The TRAP system provides 4 Relay switches each capable of switching up to 1.2KW (5A @ 230V). Each relay is independent and separately controlled. The TRAP series remote control system provides switched contacts and can therefore be used to switch most voltages either AC or DC. 1. Open the enclosure by removing fixing screws from the enclosure front and then removing the front from the enclosure. 2. Connect the power supply screw terminals 12-32V ac or dc to the low voltage terminals. 3. Wire your desired connections to the relay switches 4. Once all required wiring is complete, use the handheld TRAP transmitter to switch the outputs on and off. 5. As supplied, the handheld will operate the outputs - Button 1 to output 1, Button 2 to output 2 etc. 6. For additional functions including operation such as adding extra transmitters, different button map ping options, changing the outputs to latching, see advanced operation section. Application Circuit. NO COM 12V NC LOAD Relay TRAP-RX 0V Relay Relay 12V 0V Supply Terminals Notes for clay pigeon release applications PLEASE READ BEFORE ATTEMPTING INSTALLATION: This system is supplied complete with cable in order to connect to the clay trap release. Warning : Not all clay traps have the same wiring convention! The system is pre-wired (as diagram below) before connecting, CHECK YOUR CONNECTIONS. (using a multi-meter) if you are in any doubt, DO NOT CONNECT THE SYSTEM, consult a qualified Electrician. Although the system operates on 12-32V DC damage may occur to the receiver unit if wrong connections are made. For easy installation we offer the following prewired Systems Promatic Laporte Acorn Autosporter TRAP-S1PROM TRAP-S1LAP TRAP-S1ACORN TRAP-S1AUTO DS-TRAP-3 PAGE 3 Trap remote control system Advanced Operation Configuring receivers Receivers can be used for many applications. The Link Pins LK1 and LK2 set the action of the relays 1 = Relay will operate for 1/2 sec = Relay will operate for as long as transmitter switch operated = Relay will toggle ON/OFF on each transmitter button press /2 sec Mom Mom Latch Link Pins LK1 LK2 Link Positions LK1 LK2 Switched outputs RLY 2 RLY 3 RLY 1 1 /2 sec Mom 1 /2 sec Mom 1 1 Open Open Closed Open Open Closed Mom Mom Mom Mom Latch Mom Latch Mom Closed Closed Latch Latch Latch Latch DS-TRAP-3 PAGE 4 /2 sec Mom RLY 4 /2 sec Mom Trap remote control system Advanced operation - Pairing a transmitter button With this system, you can pair together any individual transmitter switch with any receiver output relay. Without opening either box. 1. Remove the green transmitter rubber overboot 2. Briefly (for less than 1 second) place the transmitter next to the receiver in the position shown and then remove it. 3. The receiver will Buzz once (One Buzz means the receiver unit is ready to allocate a transmitter to Relay switch 1) 4. Press the switch on the transmitter which you wish to pair 5. The receiver will buzz once to confirm pairing 6. Repeat for any additional transmitter switches NOTE: each receiver has a maximum memory for up to 28 pairings, these can be from any Switches on any transmitters! Advanced Note: It is possible to select relay output switches 2-4, by repeating step 3 and counting the number of buzzes. 2 buzzes for relay 2 3 for 3 etc. Advanced operation - Erasing receiver memory 1. Hold the transmitter in the position shown in position for ~5 seconds. 2. The receiver will sound a long buzz to confirm erased DS-TRAP-3 PAGE 5 Trap remote control system Technical specifications Transmitters: TRAP-Transmitter Enclosure Rating: Standard IP67 (upgradeable to IP68) Battery Type: 3 x AAA (supplied) Battery Life: 5 years @ approx. 50 1/2second presses p/day Dimensions: 90 x 54 x 27 mm Changing the Battery: Remove the six enclosure screws. Remove 2 battery compartment screws and replace batteries, taking care of cables and battery polarity Electrical Characteristics Supply Voltage Frequency: RF Output Power (ERP) @ 869.50 MHz Min - Typical 4.5 869.500 100 Max Units V MHz mW Receiver Decoder: TRAP-Receiver Enclosure Rating: IP68 Dimensions: 130 x 112 x 42 mm (not including antenna) Operating Temperature: -10 to +50o Celsius. ELECTRICAL CHARACTERISTICS Supply Voltage MIN TYPICAL MAX DIMENSION 12 12 32 V ac or dc 5 12 A Relay Rating* (230Vac) RLY1-4 Supply Current : Quiescent All relays operating* 40 140 mA Time delay from Tx on Switch to Rx Relay operation 30 mS Time delay from Tx sw relax to Rx Relay release 30 mS *The relay contacts in this unit are for functional use only and must not be used for isolation purposes Approvals Information: All RF Solutions products are manufactured in accordance with our ISO:9001 Quality System Further information available on request. Waste Batteries and Accumulators Directive 2006/66/EC Where batteries are fitted, before recycling the product, the batteries must be removed and disposed of at a licensed collection point. RF Solutions Ltd. Recycling Notice Meets the following EC Directives: DO NOT Discard with normal waste, please recycle. ROHS Directive 2002/95/EC Specifies certain limits for hazardous substances. Environment Agency producer registration number: WEE/ WEEE Directive 2002/96/EC Waste electrical & electronic equipment. This product must be disposed of through a licensed WEEE collection point. RF Solutions Ltd., fulfils its WEEE obligations by membership of an approved compliance scheme. Whilst the information in this document is believed to be correct at the time of issue, RF Solutions Ltd does not accept any liability whatsoever for its accuracy, adequacy or completeness. No express or implied warranty or representation is given relating to the information contained in this document. RF Solutions Ltd reserves the right to make changes and improvements to the product (s) described herein without notice. Buyers and other users should determine for themselves the suitability of any such information or products for their own particular requirements or specification(s). RF Solutions Ltd shall not be liable for any loss or damage caused as a result of user’s own determination of how to deploy or use RF Solutions Ltd’s products. Use of RF Solutions Ltd products or components in life support and/or safety applications is not authorised except with express written approval. No licences are created, implicitly or otherwise, under any of RF Solutions Ltd’s intellectual property rights. Liability for loss or damage resulting or caused by reliance on the information contained herein or from the use of the product (including liability resulting from negligence or where RF Solutions Ltd was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict RF Solutions Ltd’s liability for death or personal injury resulting from its negligence. DS-TRAP-3 PAGE 6 Trap remote control System Range Test Notes Our Range Testing was conducted on Ditchling Beacon providing an open Line of Sight Test. 1. Receiver was mounted on the Bonnet of our vehicle in the Beacon Car park 2. The transmitter was carried along the beacon whilst being repeatedly operated 3. 2KM range was achieved, the system was working 100% however testing ceased as we ran out of land. 4. Weather Conditions 5. Warm, Dry, Sunny, Broken Cloud, 22degC Ditchling Beacon R F Solutions Ltd., William Way, Burgess Hill, West. Sussex. RH15 9AG. England. Email : [email protected] Tel Sales: http://www.rfsolutions.co.uk 01444 227900 William Alexander House, William Way , Burgess Hill, West Sussex, United Kingdom, RH15 9AG Tel. Sales:+44(0)1444 227910 —Tech Sales:+44(0)1444 227909