K-Band 500 W Peak Power Reverse Ka-Band ODU Built for Outdoor Applications Provides 500 watts of peak power in a rugged and compact weatherproof package, digital ready, for wideband singleand multi-carrier satellite service over 600 MHz over the reverse Ka-band frequency band. Ideal for both transportable and fixed earth station applications. Cost Effective and Efficient Employs a high efficiency helix traveling wave tube, reducing operating costs. An integral BUC is available as an option. Rugged and Easy to Maintain Built-in fault diagnostic capability via remote monitor and control. Easy access enclosure for improved serviceability. CAN-Bus architecture improves reliability and improves noise immunity. Meets Global Requirements Meets International Safety Standard EN-60215, Electromagnetic Compatibility 2004/108/EC and Harmonic Standard EN-61000-3-2 to satisfy worldwide requirements. CE certified. Worldwide Support Model TL05KO 500 watt K-band outdoor TWTA for satellite uplink applications OPTIONS •Remote control panel •Internal switch control and drive •Redundant or power combined subsystems •Integral L-Band Block Upconverter (BUC) - contact CPI for specifications when BUC is included •Integral Linearizer •RS-422/485 serial interface •Harmonic Filter - lowers harmonic output to -60 dBc max (reduces peak and CW power by 10 W) Backed by over three decades of satellite communications experience, and CPI’s worldwide 24-hour customer support network that includes more than 20 regional factory service centers. 811 Hansen Way, PO Box 51625 Palo Alto, CA 94303 USA tel: +1 (650) 846-3803 fax: +1 (650) 424-1744 e-mail:[email protected] website:www.cpii.com/satcom K-Band Specifications 500 W Peak Power Reverse Ka-Band Outdoor TWTA Specification Model TL05KO Output Frequency 24.65 to 25.25 GHz TWT Peak/CW Power1 500 W/300 W (56.99/54.77 dBm) Flange Peak/CW Power1 415 W/250 W (56.18/53.98 dBm) Intermodulation - with respect to the sum of two carriers -25 dBc max. at total output power of 50.7 dBm (at 53.7 dBm with optional linearizer) Intermodulation - with respect to each of 2 equal carriers 5 MHz apart -25 dBc max. at total output power of 49.2 dBm (at 52.2 dBm with optional linearizer) Gain 70 dB min. at rated output, 70 dB typ. at small signal RF Level Adjust Range 0 to 30 dB (via PIN diode attenuator) typ, 0.1 dB steps Gain Stability ±0.25 dB/24 hour max,max. at constant drive and temperature, after 30 minute warmup ±0.75 dB max. from ±10˚C; ±1.0 dB typ. over operating temperature range Small Signal Gain Slope ±0.04 dB/MHz max. Small Signal Gain Variation 1.0 dB pk-pk max. over 600 MHz Input/Output VSWR 1.3:1 max. Load VSWR 1.5:1 max. continuous operation, any value operation without damage; 2.0:1 max. continuous Phase Noise -15 dB below IESS-308 continuous mask; -47 dBc AC fundamental; -50 dBc sum of all spurs Spurious AM/PM Conversion Harmonic Output Noise Density -60 dBc max. 2.5˚/dB max. for a single-carrier up to 7 dB OBO (2.0˚/dB max. up to 4 dB OBO with optional linearizer) -12 dBc max. at rated power (-60 dBc with optional filter) <-150 dBW/4 kHz below 21.2 GHz; <-70 dBW/4 kHz max. in passband; <-80 dBW/4 kHz typ. in passband; <-65 dBW/4 kHz max. in passband with linearizer option NPR (with linearizer option) -19 dB at 4 dB OBO typical; -20 dB at 4.3 dB OBO typical Group Delay (over 40 MHz) 0.01 ns/MHz linear max; 0.001 ns/MHz2 parabolic max; 0.5 ns pk-pk ripple max. Primary Power Voltage: Single phase, 100-240 VAC ±10%; Frequency: 47-63 Hz Power Consumption 1300 VA max; 1050 VA typ. Power Factor 0.95 min; 0.99 typ. Amplitude and Phase Linearity Ambient Temperature Exceeds MIL-STD-188-164A -40˚C to +50˚C operating in direct sunlight (to +55˚C out of direct sunlight); -54˚C to +75˚C non-operating Relative Humidity Altitude Shock and Vibration 100% condensing 10,000 ft. with standard adiabatic derating of 2˚C/1000 ft. operating; 50,000 ft. non-operating 20 G at 11 ms (1/2 sine pulse in non-operating condition); 2.1 g rms, 50 to 500 MHz Cooling Connections Forced Air with integral blower RF Input: WR-34F; RF output: WR-34G; RF output monitor: SMA Female M&C Interface Dimensions, W x H x D Ethernet (RS422/485 serial optional) 10.25 x 10.5 x 22.25 inches (261 x 267 x 566 mm) Weight 60 lbs (27.2 kg) with no options Heat Dissipation 950 W max. Acoustic noise Note 1 65 dBA (as measured at 3 ft.) nom. Peak and CW power are reduced by 10 W with harmonic filter option. Quality Management System - ISO 9001:2008 For more detailed information, please refer to the corresponding CPI technical description if one has been published, or contact CPI. Specifications may change without notice as a result of additional data or product refinement. Please contact CPI before using this information for system design. MKT 243K, ISSUE 5 dated MAR 2015