TECH. CORP. SPECIFICATIONS CUSTOMER SAMPLE CODE : : (Ver.) MASS PRODUCTION CODE DRAWING NO. (Ver.) PTC PG12232LRU-BGB-H-Q (Ver.0) : PG-95008 (Ver.) Customer Approved Date: Approved ■ QC Confirmed Designer Approval For Specifications Only. * This specification is subject to change without notice. Please contact Powertip or it’s representative before designing your product based on this specification. □ Approval For Specifications and Sample. POWERTIP TECH. CORP. Headquarters: th No.8, 6 Road, Taichung Industrial Park, TEL: 886-4-2355-8168 E-mail: [email protected] FAX: 886-4-2355-8166 Http://www.powertip.com.tw Taichung, Taiwan 台中市 407 工業區六路 8 號 NO.PT-A-005-6 RECORDS OF REVISION Date Rev. Description 2006/6/3 0 Revised Contents Note Page Total:21 Page PG12232LRU-BGB-H-Q Rev.0(DK) Page2 Contents 1. SPECIFICATIONS 1.1 1.2 1.3 1.4 1.5 1.6 Features Mechanical Specifications Absolute Maximum Ratings DC Electrical Characteristics Optical Characteristics Backlight Characteristics 2. MODULE STRUCTURE 2.1 2.2 2.3 2.4 Counter Drawing Interface Pin Description Timing Characteristics Display Command 3. QUALITY ASSURANCE SYSTEM 3.1 Quality Assurance Flow Chart 3.2 Inspection Specification 4. RELIABILITY TEST 4.1 Reliability Test Condition 5. PRECAUTION RELATING PRODUCT HANDLING 5.1 5.2 5.3 5.4 Safety Handling Storage Terms of Warranty 6. THIS PRODUCT CONFORMS THE ROHS OF PTC. Note:For detailed information please refer to IC data sheet:SBN1661G-M18-D PG12232LRU-BGB-H-Q Rev.0(DK) Page3 1. SPECIFICATIONS 1.1 Features Item Standard Value Display Type 122 * 32 dots LCD Type STN, YG, Transflective, Positive, Extended Temp. Driver Condition LCD Module:1/32 Duty , 1/5 Bias Viewing Direction 6 O’clock Backlight Yellow green LED B/L Weight - Interface - Other - 1.2 Mechanical Specifications Item Standard Value Unit Outline Dimension 80.0 (L) * 36.0 (w) * 13.5 (H)(Max) mm Viewing Area 60.5 (L) * 18.5 (w) mm Active Area 53.64 (L) * 15.64 (w) mm Dot Size 0.40 (L) * 0.45 (w) mm Dot Pitch 0.44 (L) * 0.49 (w) mm Note:For detailed information please refer to LCM drawing 1.3 Absolute Maximum Ratings Item Symbol Condition Min. Max. Unit Power Supply Voltage VDD - -0.3 7.0 V LCD Driver Supply Voltage VLCD - - 13 V Input Voltage VIN - -0.3 VDD+0.3 V Operating Temperature TOP Excluded B/L -20 70 ℃ Storage Temperature TST Excluded B/L -30 80 ℃ Storage Humidity HD Ta<40 ℃ - 90 %RH PG12232LRU-BGB-H-Q Rev.0(DK) Page4 1.4 DC Electrical Characteristics VDD = 5.0 V ± 0.5V,VSS = 0V,Ta = 25℃ Item Symbol Condition Min. Type Max. Unit Logic Supply Voltage VDD - 4.5 5.0 5.5 V “H” Input Voltage VIH - VDD-2.2 - VDD V “L” Input Voltage VIL - - 0.8 V “H” Output Voltage VOH IOH=-2.0mA - VDD V “L” Output Voltage VOL IOL=2.0mA - 0.3 V Supply Current IDD VDD = 5.0 V - 1.5 3.0 mA -20°C - - - 25°C*1 7.6 7.8 8.0 70°C - - - LCM Driver Voltage VOP VDD-0.3 V Note: *1. THE VOP TEST POINT IS VDD – VEE. 1.5 Optical Characteristics LCD Panel:1/32 Duty,1/5 Bias,VLCD =8.1 V,Ta = 25℃ Item Symbol Conditions Min. Type Max. Reference View Angle θ C>2.0, ∅ = 0° 30° - - Notes 1 & 2 Contrast Ratio C θ = 5°, ∅ = 0° 2 3 - Note 3 Response Time(rise) tr θ = 5°, ∅ = 0° - 170ms 225ms Note 4 Response Time(fall) tf θ = 5°, ∅ = 0° - 250 ms 375ms Note 4 PG12232LRU-BGB-H-Q Rev.0(DK) Page5 Note 1: Definition of angles θ and ∅ z (θ=0°) Light (when reflected) Cmax. Sensor θ Note 2: Definition of viewing angles θ1 and θ2 Y’(∅=180°) LCD panel X(∅=90°) X’ ∅ Z’ Light (when transmitted ) 2.0 θ1 Y(∅=0°) θ2 viewing angle θ (∅ fixed) (θ=90°) Note : Optimum viewing angle with the naked eye and viewing angle θ at Cmax. Above are not always the same Note 3: Definition of contrast C Note 4: Definition of response time Brightness (reflection) of unselected dot (B2) C = Brightness (reflection) of selected dot (B1) VLCD Brightness (reflection) of 0 selected dot (%) -VLCD Brightness Non-selected state B2 (reflection) of Non-selected state Contrast unselected dot Brightness Selected state 90% B1 10% (reflection) Time tr 0 tf Note: Measured with a transmissive LCD panel which is displayed 1 cm2 operating voltage (v) PG12232LRU-BGB-H-Q Rev.0(DK) VLCD : Operating voltage fFRM : Frame frequency tr tf : Response time (fall) : Response time (rise) Page6 1.6 Backlight Characteristics LCD Module with LED Backlight Maximum Ratings Item Symbol Conditions Min. Max. Unit Forward Current IF Ta =25℃ - 250 mA Reverse Voltage VR Ta =25℃ - 10 V Power Dissipation PO Ta =25℃ - 1.15 W Operating Temperature TOP - -20 70 ℃ Storage Temperature TST - -30 80 ℃ Solder Temp. for 3 Second - - 310 330 ℃ Electrical / Optical Characteristics Ta =25℃ Item Symbol Conditions Min. Type Max. Unit Forward Voltage VF IF= 100 mA - 4.2 4.6 V Reverse Current IR VR= 10 V - - 0.1 mA Average Brightness (with LCD) IV IF= 100 mA - - - cd/m2 Wavelength λp IF= 100 mA 569 - 576 nm Luminous Intensity (without LCD) IV 180 - cd/m2 IF=100 mA Color PG12232LRU-BGB-H-Q Yellow-green Rev.0(DK) Page7 2. MODULE STRUCTURE 2.1 Counter Drawing PG12232LRU-BGB-H-Q Rev.0(DK) Page8 2.2 Interface Pin Description Pin No Symbol 1 VSS Power Supply (VSS=0) 2 VDD Power Supply (VDD>VSS) 3 VEE Operating voltage for LCD (variable) 4 A0 “L” is instruction 5 CS1 Chip enable active “L”, segment 0~segment 61 6 CS2 Chip enable active “L”, segment62~segmeent122 7 CL Clock input 2KHZ 8 E R/ 9 10~17 Function Enable signal Data read & write W DB0~DB7 18 “H” is data (NOTE:A0=C/D) Data bus line Reset the system RES 19 A Power supply for LED backlight(+) 20 K Power supply for LED backlight(-) Contrast Adjust VDD 2 VEE 10~20KΩ LCD MODULE 3 119 20 Negative voltage 4.2V PG12232LRU-BGB-H-Q Rev.0(DK) Page9 2.3 Timing Characteristics •.MPU PG12232LRU-BGB-H-Q Bus Read/Write I (80-family MPU) Rev.0(DK) Page10 • MPU Bus Read/Write II (68-family MPU) PG12232LRU-BGB-H-Q Rev.0(DK) Page11 2.4 Display Command 2.4.1 Write Display Data The setting of the control bus for issuing Write Display Data command 2.4.2 PG12232LRU-BGB-H-Q Rev.0(DK) Page12 The setting of the control bus for issuing Read Display Command 2.4.3 Read-Modify-Write PG12232LRU-BGB-H-Q Rev.0(DK) Page13 The setting of the control bus for the Read-Modify-Write command PG12232LRU-BGB-H-Q Rev.0(DK) Page14 The setting of the data bus for the Read-Modify-Write command The command code is E0 Hex. 2.4.4 The END command The setting of the control bus for the END command The setting of the data bus for the END command The command code is EE Hex. 2.4.5 Software RESET command The setting of the control bus for the Software RESET Command The setting of the data bus for the Software RESET Command The command code is E2 Hex. PG12232LRU-BGB-H-Q Rev.0(DK) Page15 3. QUALITY ASSURANCE SYSTEM 3.1 Quality Assurance Flow Chart Item Customer Sales Info Marketing & Design R&D Manufactur ing Q.A Product control Purchase Inventory control Survey Request Project Inquiry evaluation Project Validation NG OK Quote Contract Design check Sample test Sample Approval NG Verification NG OK Sample approval OK Pilot Pilot Run & Mass Product NG Verification OK Specification preparation Mass production OK Ship Out PG12232LRU-BGB-H-Q run & Reliability test Inspection NG Shipment Ship out Rev.0(DK) Page16 Item Customer Sales Info Claim R&D Q.A Manufactu Product ring control Purchase Failure analysis Sales Service Analysis report Corrective action Tracking 1. ISO 9001 Maintenance Activities Q.A 3. Equipment calibration Activity 5. Standardization Management PG12232LRU-BGB-H-Q Rev.0(DK) 2. Process improvement proposal 4. Education And Training Activities Page17 Inventory control 3.2 Inspection Specification Inspection Standard:MIL-STD-105E Table Normal Inspection Single Sampling Level Ⅱ。 Equipment:Gauge、MIL-STD、Powertip Tester、Sample。 IQC Defect Level:Major Defect AQL 0.4; Minor Defect AQL 1.5。 FQC Defect Level:100% Inspection。 OUT Going Defect Level:Sampling。 Specification: NO 1 2 3 4 5 Item Specification Judge The part number is inconsistent with work order of Part Number N.G. production The quantity is inconsistent with work order of N.G. Quantity production The display lacks of some patterns. N.G. Electronic Missing line. N.G. characteristics of The size of missing dot, A is>1/2 Dot size N.G. LCM N.G. A=( L + W )÷2 There is no function. Output data is error N.G. Material is different with work order of production N.G. LCD is assembled in inverse direction N.G. Bezel is assembled in inverse direction N.G. Shadow is within LCD viewing area + 0.5 mm N.G. Appearance of The diameter of dirty particle, A is>0.4 mm N.G. LCD Dirty particle length is >3.0mm, and 0.01mm<width N.G. A=( L + W )÷2 ≦0.05mm Display is without protective film N.G. Dirty particle Conductive rubber is over bezel 1mm N.G. (Including Polarizer exceeds over viewing area of LCD N.G. scratch、bubble ) Area of bubble in polarizer, A>1.0mm, the number of N.G. bubble is >1 piece. 0.4mm<Area of bubble in polarizer, A<1.0mm, the N.G. number of bubble is >4 pieces. Burned area or wrong part number is on PCB N.G. The symbol, character, and mark of PCB are N.G unidentifiable. The stripped solder mask , A is>1.0mm N.G. 0.3mm<stripped solder mask or visible circuit, A < N.G. Appearance of 1.0mm, and the number is ≧4 pieces PCB There is particle between the circuits in solder mask N.G A=( L + W )÷2 The circuit is peeled off or cracked N.G There is any circuits risen or exposed. N.G 0.2mm<Area of solder ball, A is ≦0.4mm N.G The number of solder ball is ≧3 pieces The magnitude of solder ball, A is >0.4mm. N.G PG12232LRU-BGB-H-Q Rev.0(DK) Page18 Level Major Major Major Major Major Major Major Major Major Major Major Minor Minor Minor Minor Minor Minor Minor Major Minor Minor Minor Minor Minor Minor Minor Minor NO 6 7 8 10 Item Specification The shape of modeling is deformed by touching. Insufficient epoxy: Circuit or pad of IC is visible Appearance of molding Excessive epoxy: Diameter of modeling is >20mm A=( L + W )÷2 or height is >2.5mm The diameter of pinhole in modeling, A is >0.2mm. The folding angle of frame must be >45∘+10∘ The area of stripped electroplate in top-view of Appearance of frame frame, A is >1.0mm. A=( L + W )÷2 Rust or crack is (Top view only) The scratched width of frame is >0.06mm. (Top view only) The color of backlight is nonconforming Electrical Backlight can’t work normally. characteristic of The LED lamp can’t work normally backlight The unsoldering area of pin for backlight, A is >1/2 solder joint area. A=( L + W )÷2 The height of solder pin for backlight is >2.0mm The mark or polarity of component is unidentifiable. The height between bottom of component and surface of the PCB is floating >0.7mm D>1/4W W D Assembly parts A=( L + W )÷2 PG12232LRU-BGB-H-Q D’ Pad End solder joint width, D’ is >50% width of component termination or width of pad Side overhang, D is >25% width of component termination. Component is cracked, deformed, and burned, etc. The polarity of component is placed in inverse direction. Maximum fillet height of solder extends onto the component body or minimum fillet height is <0.5mm. Rev.0(DK) Page19 Judge Level N.G. N.G. Major Minor N.G. Minor N.G. N.G. Minor Minor N.G. Minor N.G. Minor N.G. Minor N.G. N.G. N.G. Major Major Major N.G. Minor N.G. N.G. Minor Minor N.G. Minor N.G. Minor N.G. Minor N.G. Minor N.G. Minor N.G. Minor N.G. Minor 4. RELIABILITY TEST 4.1 Reliability Test Condition NO Item 1 High Temperature Storage 2 Low Temperature Storage 3 Test Condition High Temperature /Humidity Storage Storage at 80 ±2℃ 96~100 hrs Surrounding temperature, then storage at normal condition 4hrs Storage at -30 ±2℃ 96~100 hrs Surrounding temperature, then storage at normal condition 4hrs 1.Storage 96~100 hrs 60±2℃, 90~95%RH surrounding temperature, then storage at normal condition 4hrs. (Excluding the polarizer). or 2.Storage 96~100 hrs 40±2℃, 90~95%RH surrounding temperature, then storage at normal condition 4 hrs. -20℃ → 25℃ → 70℃ → 25℃ 4 Temperature Cycling (30mins) (5mins) (30mins) (5mins) 10 Cycle 5 Vibration 10~55Hz ( 1 minute ) 1.5mm X,Y and Z direction ﹡(each 2hrs) 6 7 ESD Test Drop Test PG12232LRU-BGB-H-Q Rev.0(DK) Air Discharge: Apply 6 KV with 5 times discharge for each polarity +/- Contact Discharge: Apply 250V with 5 times discharge for each polarity +/- Testing location: Around the face of LCD Testing location: 1.Apply to bezel. 2.Apply to Vdd, Vss. Packing Weight (Kg) Drop Height (cm) 0 ~ 45.4 122 45.4 ~ 90.8 76 90.8 ~ 454 61 Over 454 46 Page20 5. PRECAUTION RELATING PRODUCT HANDLING 5.1 SAFETY 5.1.1 5.1.2 If the LCD panel breaks , be careful not to get the liquid crystal to touch your skin. If the liquid crystal touches your skin or clothes , please wash it off immediately by using soap and water. 5.2 HANDLING 5.2.1 5.2.2 5.2.8 Avoid any strong mechanical shock which can break the glass. Avoid static electricity which can damage the CMOS LSI—When working with the module , be sure to ground your body and any electrical equipment you may be using. Do not remove the panel or frame from the module. The polarizing plate of the display is very fragile. So , please handle it very carefully ,do not touch , push or rub the exposed polarizing with anything harder than an HB pencil lead (glass , tweezers , etc.) Do not wipe the polarizing plate with a dry cloth , as it may easily scratch the surface of plate. Do not touch the display area with bare hands , this will stain the display area. Do not use ketonics solvent & aromatic solvent. Use with a soft cloth soaked with a cleaning naphtha solvent. To control temperature and time of soldering is 320±10℃and 3-5 sec. 5.2.9 To avoid liquid (include organic solvent) stained on LCM . 5.2.3 5.2.4 5.2.5 5.2.6 5.2.7 5.3 STORAGE 5.3.1 Store the panel or module in a dark place where the temperature is 25℃ ±5℃ 5.3.2 5.3.3 and the humidity is below 65% RH. Do not place the module near organics solvents or corrosive gases. Do not crush , shake , or jolt the module. 5.4 TERMS OF WARRANTY 5.4.1 5.4.2 Applicable warrant period The period is within thirteen months since the date of shipping out under normal using and storage conditions. Unaccepted responsibility This product has been manufactured to your company’s specification as a part for use in your company’s general electronic products. It is guaranteed to perform according to delivery specifications. For any other use apart from general electronic equipment , we cannot take responsibility if the product is used in nuclear power control equipment , aerospace equipment , fire and security systems or any other applications in which there is a direct risk to human life and where extremely high levels of reliability are required. PG12232LRU-BGB-H-Q Rev.0(DK) Page21