MVAD040 Series www.murata-ps.com 40W 2" x 4" AC-DC Power Supply Converter DESCRIPTION The MVAD040 series switching power supplies utilize advanced component and circuit technologies to deliver high efficiency. Designed for Medical, Telecom, and Industrial applications to satisfy 1U height design considerations, the MVAD040 Series measures only 2.0" x 4.0" x 1.3". All models offer universal AC input and compliance to worldwide safety and EMC standards. ORDERING GUIDE FEATURES ATURES ITE (2nd Ed.) and Medical (3rd ed.) MOPP safety approved 30-40W compact high density 2" x 4" standard footprint High efficiency up to 89% Universal AC input Low profile - 1U package Convection-cooled operation up to 40W Complies with 5000m altitude Model Number MVAD040-05 MVAD040-12 MVAD040-24 MVAD040-48 Natural Convection Cooling 30W 40W INPUT CHARACTERISTICS Parameter Conditions Single phase DC Input Voltage Operating Range Input Frequency Turn-on Input Voltage Turn-off Input Voltage Input Current Input rising at full load Input falling at full load 90Vac input, full load At 264Vac, at 25°C cold start Inrush Current RoHS compliant UL Class I and II approved OUTPUT CHARACTERISTICS Less than 0.3W no load input power Model Number Complies with ErP/Energy Star requirement average efficiency>85.3% (24V and 48V) Main Output (V1) 5V 12V 24V 48V MVAD040-05 MVAD040-12 MVAD040-24 MVAD040-48 Min. 90 120 47 50 50 Typ. 120/230 50/60 60 Max. 264 300 63 70 70 0.9 Units Vac Vdc Hz Vac A Apk Main Output Line, Load, Cross Typical Efficiency Load Current Peak Load3 Load Capacitance Voltage (V1) Regulation @230Vac full load 5V 12V 24V 48V 0 to 6A 0 to 3.34A 0 to 1.67A 0 to 0.84A 5.0A 2.5A 1.25A 0 to 1200μF 0 to 680μF 0 to 330μF 0 to 220μF ± 2% ± 2% ± 2% ± 2% 80% 87% 88% 89% Main Output Characteristics (all models) www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html Available now at www.murata-ps.com/en/3d/acdc.html For full details go to www.murata-ps.com/rohs Parameter Conditions Min. Max. Units Transient Response (MVAD040-05 only) ±8 50% load step, 1A/μsec slew rate % Transient Response (all other models) ±5 Settling Time to 1% of Nominal 200 μsec Turn On Delay After application of input power 1 sec Output Voltage Rise Monotonic, 0 to 100% load 50 msec Setpoint Accuracy 120Vac, 40W, 25°C ± 0.5 % Output Holdup, MVAD040-05 only 115Vac, 100% load 20 msec Output Holdup, all other models 115Vac, 100% load 15 msec Temperature Coefficient 0.02 %/°C 1 % Ripple Voltage & Noise1 1. Ripple and noise are measured with 0.1 μF of ceramic capacitance and 47 μF of electrolytic capacitance on each of the power supply outputs. The output noise requirements apply over a 0 Hz to 20 MHz bandwidth. A short coaxial cable with 50ohm scope termination is used. 2. Unless otherwise specified all readings are taken at 120Vac input and 25 °C ambient temperature. 3. Peak current lasting <15 seconds with a maximum 10% duty cycle and with an average output power of 40W. CB Test Certificate and Test Report www.murata-ps.com/support MVAD040.B01 Page 1 of 6 MVAD040 Series 40W 2" x 4" AC-DC Power Supply Converter ENVIRONMENTAL CHARACTERISTICS Parameter Storage Temperature Range Operating Temperature Range Operating Humidity Operating Altitude MTBF Shock Vibration Safety Warranty Outside Dimensions Weight Conditions Min. -40 -20 -20 10 -200 -200 1M Typ. See thermal derating curves Start up Non-condensing For Class I ITE Equipment deployment Other Telcordia SR-332 M1C3 25°C Operating, IEC60068-2-27, half-sine 5G, 6ms, Complies 3 times per face, 6 faces Non-operating, IEC60068-2-27, half-sine, 30G, 18ms, 3 times per face, 6 faces Complies Operating, IEC60068-2-6, 1.0G, 10-150Hz, 10minutes per axis, on all 3 axes Complies Non-operating, IEC60068-2-6, 2.0G, 10-150Hz, 10minutes per axis, on all 3 axes Complies Max. 85 70 Units 95 5000 2000 % °C m Hours IEC60950-1:2005 (2nd Edition); Am1:2009 UL60950-1 2nd Edition,2011-12-19, CSA C22.2 No. 60950-1-07, 2nd Edition,2011-12 EN60950-1:2006 + A11:2009 + A1:2010 + A12:2011 IEC60601-1:2005 + CORR.1(2006) + CORR.2(2007) ANSI/AAMI ES60601-1 (2005+C1:09 + A2:10), CSA-C22.2 No. 60601-1(2008), MOPP CE Marking per LVD 2 years 2.0" x 4.0" x 1.3" (50.8mm x 101.6mm x 33.02mm) 0.28lbs (127g) typical (MVAD040-05 only) 0.27lbs (123g) typical (all other models) PROTECTION CHARACTERISTICS Parameter Overvoltage Protection Overcurrent Protection, MVAD040-05 only Overcurrent Protection, all other models Conditions Latching (60% load) Hiccup mode Hiccup mode Min. 110 110 170 Typ. Max. 160 160 240 Units %V1 %A %A Conditions Primary to Earth Ground (1xMOPP) Primary to Secondary (2xMOPP)4 Secondary to Earth Ground 240Vac, 60Hz, 25°C 264Vac, 60Hz, 25°C 264Vac, 60Hz, 25°C Min. 1500 4000 500 Typ. Max. Units ISOLATION CHARACTERISTICS Parameter Isolation Leakage Current (under normal conditions) Touch Current Vac Vdc 300 350 100 μA EMISSIONS AND IMMUNITY Characteristic Input Current Harmonics Voltage Fluctuation and Flicker Conducted Emissions ESD Immunity Radiated Field Immunity Electrical Fast Transient Immunity Surge Immunity RF Conducted Immunity Magnetic Field Immunity Voltage dips, interruptions 4. At class I equipment. Standard IEC/EN 61000-3-2 IEC/EN 61000-3-3 EN 55022 FCC Part 15 IEC/EN 61000-4-2 IEC/EN 61000-4-3 IEC/EN 61000-4-4 IEC/EN 61000-4-5 IEC/EN 61000-4-6 IEC/EN 61000-4-8 IEC/EN 61000-4-11 Compliance Class A Complies Class B, Class A (at Class II equipment) Class B, Class A (at Class II equipment) Level 4, Criterion A Level 2, Criterion A Level 3, Criterion A Level 4, Criterion A Level 2, Criterion A Level 2, Criterion A Level 3, Criterion B www.murata-ps.com/support MVAD040.B01 Page 2 of 6 MVAD040 Series 40W 2" x 4" AC-DC Power Supply Converter EMI CONSIDERATIONS For optimum EMI performance, the power supply should be mounted to a metal plate grounded to all 4 mounting holes of the power supply. To comply with safety standards, this plate must be properly grounded to protective earth (see mechanical dimension notes). Pre-compliance testing has shown the standalone power supply to comply with EN55022 class A radiated emissions. Radiated emission results vary with system enclosure and cable routing paths. SAFETY CONSIDERATIONS 1. This power supply is a component level power supply intended for use in class I or class II applications. Secondary ground traces need to be suitably isolated from primary ground traces when used in class II applications. 2. When the power supply is used in class II equipment, all ground traces and components connected to the primary side are considered primary for spacing and insulation considerations. 3. Double pole/neutral fusing. PERFORMANCE DATA MVAD040-12 Eĸciency (%) MVAD040-05 Eĸciency (%) 88 95 86 93 84 91 82 89 80 87 78 85 76 83 AC90V AC115V AC230V AC264V 74 72 70 AC90V AC115V AC230V AC264V 81 79 77 75 68 0 1 2 3 4 5 6 0 0.5 1 1.5 2 2.5 3 3.5 Output current (A) Output current (A) MVAD040-24 Eĸciency (%) MVAD040-48 Eĸciency (%) 95 95 93 93 91 91 89 89 87 87 85 85 83 83 AC90V AC115V AC230V AC264V 81 79 77 AC90V AC115V AC230V AC264V 81 79 77 75 75 0 0.3 0.6 0.9 1.2 1.5 1.8 0.0 0.2 0.4 Output current (A) 0.6 0.8 1.0 Output current (A) Inrush waveform (AC264V 25°C) 45 Output power (W) 40 35 30 25 MVAD040-12/24/48 Thermal DeraƟng MVAD040-05 Thermal DeraƟng 20 15 10 5 0 -20 -10 0 10 20 30 40 50 Ambient temperature (°C) 60 70 80 www.murata-ps.com/support MVAD040.B01 Page 3 of 6 MVAD040 Series 40W 2" x 4" AC-DC Power Supply Converter MECHANICAL DIMENSIONS – MVAD040-05 ONLY All dimensions in inches (mm). tolerance is +/-0.02’ (0.5) Mounting holes H1 and H2 should be earth-grounded for EMI purpose Mounting holes H2 is earth ground connection This power supply requires mounting on standoffs minimum 0.2' (5.0) in height Dimensions: 2.0" x 4.0" x 1.3" (50.8mm x 101.6mm x 33.02mm) INPUT/OUTPUT CONNECTOR AND SIGNAL SPECIFICATION AND MATING CONNECTORS PIN Description Input Connector CN1 : Molex 26-62-4030 1 AC Line (V-) 3 AC Neutral (V+) Spade Connector: #250 GND Earth Ground Output Connector CN2 : Molex 26-60-4040 1, 2 V1 3, 4 DC Return Mating Housing Crimp terminal/pins Molex 09-50-8031 with locking ramp Molex 6838 Series Molex 09-50-8041 with locking ramp Molex 6838 Series www.murata-ps.com/support MVAD040.B01 Page 4 of 6 MVAD040 Series 40W 2" x 4" AC-DC Power Supply Converter MECHANICAL DIMENSIONS – MVAD040-12 ONLY All dimensions in inches (mm). tolerance is +/-0.02’ (0.5) Mounting holes H1 and H2 should be earth-grounded for EMI purpose Mounting holes H2 is earth ground connection This power supply requires mounting on standoffs minimum 0.2' (5.0) in height Dimensions: 2.0" x 4.0" x 1.3" (50.8mm x 101.6mm x 33.02mm) INPUT/OUTPUT CONNECTOR AND SIGNAL SPECIFICATION AND MATING CONNECTORS PIN Description Input Connector CN1 : Molex 26-62-4030 1 AC Line (V-) 3 AC Neutral (V+) Spade Connector: #250 GND Earth Ground Output Connector CN2 : Molex 26-60-4040 1, 2 V1 3, 4 DC Return Mating Housing Crimp terminal/pins Molex 09-50-8031 with locking ramp Molex 6838 Series Molex 09-50-8041 with locking ramp Molex 6838 Series www.murata-ps.com/support MVAD040.B01 Page 5 of 6 MVAD040 Series 40W 2" x 4" AC-DC Power Supply Converter MECHANICAL DIMENSIONS – MVAD040-xx 24V and 48V MODELS All dimensions in inches (mm). tolerance is +/-0.02’ (0.5) Mounting holes H1 and H2 should be earth-grounded for EMI purpose Mounting holes H2 is earth ground connection This power supply requires mounting on standoffs minimum 0.2' (5.0) in height Dimensions: 2.0" x 4.0" x 1.3" (50.8mm x 101.6mm x 33.02mm) INPUT/OUTPUT CONNECTOR AND SIGNAL SPECIFICATION AND MATING CONNECTORS PIN Description Input Connector CN1 : Molex 26-62-4030 1 AC Line (V-) 3 AC Neutral (V+) Spade Connector: #250 GND Earth Ground Output Connector CN2 : Molex 26-60-4040 1, 2 V1 3, 4 DC Return Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. ISO 9001 and 14001 REGISTERED Mating Housing Crimp terminal/pins Molex 09-50-8031 with locking ramp Molex 6838 Series Molex 09-50-8041 with locking ramp Molex 6838 Series This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy. Refer to: http://www.murata-ps.com/requirements/ Murata Power Solutions, Inc. (“Murata”) makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards that anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm, and take appropriate remedial actions. Buyer will fully indemnify Murata, its affiliated companies, and its representatives against any damages arising out of the use of any Murata products in safety-critical applications. Specifications are subject to change without notice. © 2014 Murata Power Solutions, Inc. www.murata-ps.com/support MVAD040.B01 Page 6 of 6