AGF-10 SERIES AC/DC Power Module 10W FEATURES ►Fully Encapsulated Plastic Case for PCB Mounting ►Universal Input 85~264VAC, 47~440Hz ►Protection Class II as per IEC/EN 60536 ►I/O Isolation 3000VAC with Reinforced Insulation ►Operating Ambient Temp. Range -25°C to +70°C ►Overload/Voltage/Temp. and Short Circuit Protection ►Designed-in EMI Emission meets EN55011/22 Class B & FCC Level B ►Designed-in EMC Immunity meets EN61000-4-2,3,4,5,6,8,11 ►Eco Design, Compliant to Energy Star Specification and ErP Directive 2009/125/EC ►UL/cUL/IEC/EN 60950-1 Safety Approval & CE Marking PRODUCT OVERVIEW The MINMAX AGF-10 series is a new range of fully encapsulated AC/DC power supply modules. They are designed for direct PCB mounting with solder pins. The product features EMI-filter to EN55022, class B and EMS compliance to the EN 61000-4 standard. Universal input voltage 85-264VAC and International safety approvals qualifies these power modules for applications in products with worldwide markets. The AGF-10 series provide a cost effective solution for many space critical applications in commercial and industrial electronic equipment. Model Selection Guide Model Output Number Voltage Output Current Max. mA 2500 2000 833 667 417 VDC 3.3 5 12 15 24 AGF-10S03 AGF-10S05 AGF-10S12 AGF-10S15 AGF-10S24 Input Current Max. capacitive Efficiency 115VAC, 60Hz @Max. Load mA(typ.) 171 201 191 193 201 Load (typ.) @Max. Load % 70 72 76 75 72 uF 2200 2200 1000 1000 680 Input Specifications Parameter Model / Conditions Input Voltage Range Input Frequency Range Input Voltage Range No-Load Power Consumption All Models 115VAC 230VAC Inrush Current External Fuse (Recommended) Cold Start at 25℃ Min. Typ. Max. Unit 85 47 120 ------- --264 --440 --370 --0.3 --15 --30 1.5A Slow – Blow Type VAC Hz VDC W A A All Models Output Specifications Conditions Parameter Output Voltage Setting Accuracy Line Regulation Load Regulation Vin=Min. to Max. Io=Min. to Max. 0-20 MHz Bandwidth Ripple & Noise Minimum Load Over Voltage Protection Temperature Coefficient Overshoot Zener diode clamp ------- Typ. ±1.0 ±0.5 ±0.5 1.5 0.8 Max. ±2.0 ±1.0 ±1.0 1.8 1.0 Unit %Vnom. % % %VPP of Vo %VPP of Vo --------- 10 120 ±0.01 --- ----±0.02 5 %Inom. % of Vo %/℃ % Vout --- %Inom. Foldback, auto-recovery 105 --(long term overload condition may cause damage) Hiccup mode, Automatic Recovery Current Limitation Short Circuit Protection E-mail:[email protected] 2015/07/31 REV:13 3.3 & 5.0VDC Output Models Other Output Models Min. ----- Tel:886-6-2923150 Page 1 of 3 AGF-10 SERIES AC/DC POWER MODULE 10W General Specifications Parameter I/O Isolation Voltage I/O Isolation Resistance Switching Frequency Hold-up Time MTBF (calculated) Protection Class II Safety Approvals Conditions Input to Output, 60 Seconds 500 VDC Min. 3000 100 ----- Typ. ----125 20 MIL-HDBK-217F@25℃, Ground Benign 300,000 According IEC/EN 60536 UL/cUL 60950-1,IEC/EN 60950-1 Max. --------- Unit VACrms MΩ KHz ms Hours Environmental Specifications Parameter Operating Ambient Temperature Range (See Power Derating Curve) Storage Temperature Range Power Derating Over Temperature Protection Humidity (non condensing) Cooling Conditions Min. Max. Unit Natural Convection -25 +70 ℃ -40 +85 ℃ W/℃ 95 % rel. H +50℃ to +70℃ 0.375 at 90℃ (automatic recovery at 67℃) --Natural Convection EMC Specifications Parameter Standards & Level EMI Conduction and Radiation EMS EN55011 ,EN55024 ESD Radiated immunity Fast transient Surge Conducted immunity PFMF Dips Interruptions Performance EN55011, EN55022, FCC part 15 Class B EN61000-4-2 air ± 8kV , Contact ± 4kV EN61000-4-3 10V/m EN61000-4-4 ±2kV EN61000-4-5 ±1kV EN61000-4-6 10Vrms EN61000-4-8 30A/m EN61000-4-11 30% 10ms EN61000-4-11 >95% 5000ms B A B B B A B C Notes 1 Specifications typical at Ta=+25℃, resistive load, 115VAC, 60Hz input voltage and after warm-up time rated output current unless otherwise noted. 2 We recommend to protect the converter by a slow blow fuse in the input supply line. 3 These power modules require a minimum output loading to maintain specified regulation, operation under no-load conditions will not damage the power 4 Other input and output voltage may be available, please contact factory. supplies however they may not meet all listed specifications. 5 That “natural convection” is about 20LFM but is not equal to still air (0 LFM). 6 Specifications are subject to change without notice. E-mail:[email protected] 2015/07/31 REV:13 Tel:886-6-2923150 Page 2 of 3 AGF-10 SERIES AC/DC POWER MODULE 10W Package Specifications Mechanical Dimensions Pin Connections 23.5 [0.93] 10.0 [0.39] 10.16 [0.40] 2 AC(N) – AC Neutral 2 AC(L) – AC Line 3 +Vout 4 -Vout 5.0 [0.20] Bottom View Function 1 52.4 [2.06] 1.0 [ 0.04] 3 45.72 [1.80] 4 0.7 [0.03] Pin 1 ►All dimensions in mm (inches) ►Tolerance: ±0.5 20.32 [0.80] ►Pin (±0.02) diameter 1.0 ±0.1 (0.04±0.004) 27.2 [1.07] Physical Characteristics Case Size : 52.4x27.2x23.5mm (2.06x1.07x0.93 Inches) Case Material : Plastic resin (flammability to UL 94V-0 rated) Weight : 54g 18, Sin Sin Road, An-Ping Industrial District, Tainan 702, Taiwan Tel: 886-6-2923150 Fax: 886-6-2923149 E-mail: [email protected] Minmax Technology Co., Ltd. 2015/07/31 REV:13 Page 3 of 3