MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS NEW VM,VL For Refolw Series Solvent Proof WV 100V Suitable for CFL, adapter and power supply VM series is load life of 5000 hours at 105 C VL series is load life of 8000 hours at 105 C Complied to the RoHS directive Item Characteristics Operating temperature range -40 ~ 105 C WV > 100 I = 0.02CV + 25 A (after 5 min.) WV 100 I = 0.01CV or 3 A whichever is greater (after 2 min.) Leakage current max. 20% at 120Hz, 20 Capacitance tolerance 25 0.16 35 0.13 50 0.12 100 0.08 160 0.14 250 0.20 WV Z-40 C/Z+20 C 25 5 35 4 50 3 100 3 160 6 250 8 Dissipation factor max. (at 120Hz, 20 C) Low temperature characteristics (Impedance ratio at 120Hz) C WV tan Load life After application of the rated voltage 5000(VM), 8000(VL) hours at 105 C Leakage current Less than specified value Capacitance change Within 20% of initial value tan Less than 200% of specified value Shelf life (at 105 C) After 1000 hours no load test, leakage current, capacitance and tan are same as load life value. The measurement shall be performed after exposure for 24 hours at room temperature after application of DC reted voltage to the capacitors for 30 minutes. Unit : mm DRAWING d0.05 Tinned copper-ply wire D 0.5 max. Insulating sleeve P0.5 L max. 15 min. D 8 10 P 3.5 5.0 d 0.5 0.6 1.5 2.0 4 min. Safety vent MINIATURE TYPES DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT WV F 15 22 33 47 68 82 100 180 220 330 470 560 680 820 1000 25 35 50 100 160 8 8 10 8 10 10 8 10 10 8 8 10 10 10 20 20 16 20 20 780 930 1089 1351 1600 8 10 10 20 20 20 20 16 20 810 1029 1295 20 16 20 20 20 20 250 375 469 625 8 10 10 20 16 20 375 469 625 630 725 830 760 810 890 Ripple current (mA rms) at 105 C, 100kHz Case size D L (mm) FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT F Frequency ~ 33 120Hz 300Hz 1kHz 10kHz 100kHz 0.32 0.60 0.80 0.90 1.00 39 ~ 270 0.40 0.63 0.82 0.91 1.00 330 ~ 1000 0.45 0.67 0.84 0.92 1.00 Refer to page 182 for soldering recommendation. 181 MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS Reflow soldering method for series of VM, VL 1. Recommended conditions for reflow soldering The aluminum electrolytic capacitor is subjected to soldering by reflow method. Temperature and time conditions of reflow soldering shall be set as per each temperature profile shown below as a standard. The following are recommended conditions in the case of reflow soldering method for the aluminum electrolytic capacitor. (1) The capacitor shall not be subjected to either flow or dip soldering method. (2) Avoid soldering twice by reflow. The number of reflow time for aluminum electrolytic capacitor shall be once basically. If this type of capacitor has to be inevitably subjected to the reflow twice, enough cooling time between the first and the second reflow (at least more than 30 minutes) shall be taken to avoid the consecutive reflows by all means. (3) On setting the reflow conditions, it shall be done lest the temperature at surface of the capacitor should exceed more than 175 C 2. RECOMMENDED REFLOW SOLDERING CONDITIONS Tp Tp TL Ramp-up Ts max. tL Ts min. Ramp down Preheat 0 Ts (150 C max., 120sec.max) Time (sec.) t (25 C to Peak) Profile Feature Average Ramp-up Rate (TL to TP) Temperature Min. (TS min) Preheat Temperature Max. (TS max) Time (TS min to TS max) TS max to TL - Ramp-up Rate Temperature (TL) Time maintained above Time (tL) Peak/classification Temperature (TP) Time within 5 C of actual peak temperature(TP) Ramp-Down rate Time 25 C to peak temperature 182 Soldering condition 8 ~ 10 2 C / second max. 100 C 125 C 60 ~ 90 seconds 2 C / second max. 140 C 40 ~ 60 seconds 175 C 10 seconds max. 3 C / second max. 6 minute max.