CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CV Chip Type, High Voltage / Long Life series High voltage (to 63V), Low ESR, High ripple current. Load life of 3000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Compliant to the RoHS directive (2002/95/EC). CV CF High Voltage Long Life Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 16 to 63V Rated Capacitance Range 5.6 to 470µF ± 20% at 120Hz, 20°C Capacitance Tolerance Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C ESR ( Less than or equal to the specified value at 100kHz, 20°C 1) Leakage Current ( 2) Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C Temperature Characteristics (Max.Impedance Ratio) Z+105°C / Z+20°C Z– 55°C / Z+20°C Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 3000 hours at 105°C. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Damp Heat (Steady State) The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 60°C, 90% RH. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value 1.25 1.25 (100kHz) After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right, provided that it's temperature profile is measured at the capacitor top and the terminal. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. The duration for over +230°C temperature at capacitor surface shall not exceed 60 seconds. In the case of peak temp, less than 250°C, reflow soldering shall be two times maximum. In the case of peak temp, less than 260°C, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Navy blue print on the case top Resistance to Soldering Heat Marking 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. Dimensions φD + 0.5 MAX. C±0.2 2 3 4 5 6 7 8 9 10 11 12 13 14 PCV 1 V 8 2 0 MC L 1 GS Taping code Configuration A±0.2 E B± 0.2 Size code Capacitance toleranc (±20%) Rated capacitance (82µF) L +0.1 - 0.4 Voltage (V:35V) Series 1 0.5 MAX. Lot No. CV 82 V 012 Capacitance Type numbering system (Example : 35V 82µF) Positive Plastic platform 0.3 MAX. Rated voltage (35V) Negative Series name H Type (mm) Size φ6.3 × 6L φ8 × 7L φ8 × 10L φ8 × 12L φ10 × 8L φ10 × 10L φ10 × 12.7L φD 6.3 8.0 8.0 8.0 10.0 10.0 10.0 L 5.9 6.9 9.9 11.9 7.9 9.9 12.6 A 7.3 9.0 9.0 9.0 11.0 11.0 11.0 B 6.6 8.3 8.3 8.3 10.3 10.3 10.3 C 6.6 8.3 8.3 8.3 10.3 10.3 10.3 E 2.1 3.2 3.2 3.2 4.6 4.6 4.6 H 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 Dimension table in next page. Voltage V 16 20 25 35 50 63 Code C D E V H J CAT.8100Z CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CV series Standard Ratings Rated Voltage (V)(code) Surge Voltage (V) Rated Capacitance (µF) Case Size φD × L (mm) tan δ Leakage Current (µA) 56 6.3 × 6 8×7 0.12 179 0.12 320 0.12 100 220 16 (1C) 18.4 220 23.0 704 31 2000 PCV1C221MCL1GS PCV1C271MCL1GS 0.12 1056 26 2400 PCV1C331MCL1GS 0.12 1504 25 2800 PCV1C471MCL1GS 47 6.3 × 6 0.12 188 55 1000 PCV1D470MCL1GS 68 8×7 0.12 272 45 1300 PCV1D680MCL1GS 150 8 × 10 0.12 600 28 2000 PCV1D151MCL6GS 150 10 × 8 0.12 600 33 1900 PCV1D151MCL1GS 220 8 × 12 10 × 10 0.12 880 27 2300 PCV1D221MCL1GS 0.12 1080 27 2300 PCV1D271MCL1GS 10 × 12.7 6.3 × 6 0.12 1320 26 2700 PCV1D331MCL1GS 0.12 165 60 900 PCV1E330MCL1GS 8 ×7 8 × 10 0.12 280 50 1300 PCV1E560MCL1GS 0.12 600 29 1900 PCV1E121MCL6GS 10 × 8 8 × 12 0.12 600 35 1800 PCV1E121MCL1GS 0.12 750 28 2200 PCV1E151MCL1GS 10 × 10 10 × 12.7 0.12 900 28 2300 PCV1E181MCL1GS 0.12 1350 27 2700 PCV1E271MCL1GS 6.3 × 6 8 ×7 0.12 126 64 900 PCV1V180MCL1GS 0.12 189 55 1200 PCV1V270MCL1GS 8 × 10 10 × 8 0.12 392 31 1900 PCV1V560MCL1GS 0.12 476 37 1800 PCV1V680MCL1GS 8 × 12 10 × 10 0.12 574 29 2200 PCV1V820MCL1GS 0.12 700 29 2200 PCV1V101MCL1GS 10 × 12.7 6.3 × 6 0.12 1050 28 2600 PCV1V151MCL1GS 0.12 82 81 800 PCV1H8R2MCL1GS 8 ×7 8 × 10 0.12 150 63 1100 PCV1H150MCL1GS 0.12 330 36 1700 PCV1H330MCL6GS 10 × 8 8 × 12 0.12 330 49 1500 PCV1H330MCL1GS 0.12 390 34 2000 PCV1H390MCL1GS 10 × 10 10 × 12.7 0.12 470 30 2200 PCV1H470MCL1GS 0.12 680 29 2600 PCV1H680MCL1GS 6.3 × 6 8 ×7 0.12 71 105 700 PCV1J5R6MCL1GS 0.12 126 75 1000 PCV1J100MCL1GS 8 × 10 10 × 8 0.12 277 37 1700 PCV1J220MCL6GS 0.12 277 56 1400 PCV1J220MCL1GS 0.12 340 35 2000 PCV1J270MCL1GS 33 8 × 12 10 × 10 0.12 416 31 2200 PCV1J330MCL1GS 47 10 × 12.7 0.12 592 30 2500 PCV1J470MCL1GS 120 270 18 27 56 68 82 100 150 8.2 15 33 33 39 47 68 5.6 10 22 72.4 PCV1C221MCL6GS 0.12 10 × 10 10 × 12.7 180 63 (1J) 2000 330 150 57.5 27 2300 120 50 (1H) PCV1C101MCL1GS 704 26 56 40.2 PCV1C560MCL1GS 1500 864 33 35 (1V) 1000 36 0.12 330 28.7 50 8 × 12 270 25 (1E) 10 × 8 Part Number 270 470 20 (1D) 8 × 10 Rated Ripple (mArms) ESR (mΩ) 。 (at 100kHz 20 C) 22 27 Rated ripple current (mArms) at 105°C 100kHz No marked, 1 will be put at 12th digit of type numbering system. : In this case, 6 will be put at 12th digit of type numbering system. Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100Z