SHOULDER ELECTRONICS LIMITED CERAMIC RESONATOR Data Sheet PRODUCT 产 品: CERAMIC MODEL NO 型 号: ZTA…MX PREPARED 编 制: Fengyu CHECKED 审 核: York APPROVED 批 准: Lijiating DATE Http://www.shoulder.cn 日 期: RESONATOR 2008-01-25 Page: 1 SHOULDER ELECTRONICS LIMITED 1 SCOPE This specification shall cover the characteristics of the ceramic resonator 13.01-50.00MHZ. 2 PART NO. PART NUMBER CUSTOMER PART NO SPECIFICATION NO ZTA…MX 3 OUTLINE DRAWING AND DIMENSIONS 3.1 Appearance: No visible damage and dirt. 3.2 Construction: Leads are soldered on electrode and body is molded by resin. 3.3 Except the chip(ceramic element, ceramic base, capacitance slice), the materials don’t contain lead. 3.4 Dimensions 5.0max 5.0±1.0 7.5max 10.0max 0.5±0.1 0.3±0.1 5.0±0.30 4 RATING AND ELECTRICAL SPECIFICATIONS 4.1 RATING Items Content Withstanding Voltage (V) 50 (DC，1min) Insulation Resistance Ri,（MΩ）min. 100 （100V，1min） Operating Temperature Range (℃) -20～+80 Storage Temperature Range (℃) -55～+85 Http://www.shoulder.cn Page: 2 SHOULDER ELECTRONICS LIMITED 4.2 ELECTRICAL SPECIFICATIONS Items Oscillation Frequency Fosc（MHz） Frequency Accuracy （%） Resonant Impedance Ro（Ω）max. Content 13.01-50.00 ±0.5 30 ±0.3 （Oscillation Frequency drift，-20℃～+80℃） 6V DC 15V p-p ±0.3 （For Ten Years） Temperature Coefficient of Oscillation Frequency （%） max. Rating Voltage UR（V）max. Aging Rate （%）max. 5 MEASUREMENT 5.1 Measurement Conditions Parts shall be measured under a condition ( Temp.：20℃±15℃,Humidity ：65%±20% R.H.) unless the standard condition(Temp.：25℃±3℃,Humidity ：65%±5% R.H.) is regulated to measure. 5.2 Test Circuit IC：1/6TC74HCU04×2 X：CERAMIC RESONATOR C1 C2：15pF 6 PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS No 6.1 6.2 6.3 Item Humidity High Temperature Exposure Low Temperature Exposure Http://www.shoulder.cn Performance Requirements Condition of Test Subject the resonator at +40 ℃±2℃ and 90%~95% R.H. for 500h, resonator shall be measured after being placed in natural conditions for 1h. Subject the resonator to +85 ℃ ± 5 ℃ for 500h, resonator shall be measured after being placed in natural conditions for 1h. Subject the resonator to–25 ℃ ± 5 ℃ for 500h, resonator shall be measured after being placed in natural conditions for 1h. Page: 3 It shall fulfill the specifications in Table 1. It shall fulfill specifications Table 1. It shall fulfill specifications Table 1. the in the in SHOULDER ELECTRONICS LIMITED 6.4 6.5 Temperature Cycling Vibration Subject the resonator to －25℃ for 30min. followed by a high temperature of +85℃ for 30min. Cycling shall be repeated 5 times. Resonator shall be measured after being placed in natural conditions for 1h. Subject the resonator to vibration for 2h each in x y and z axis with the amplitude of 1.5mm, the frequency shall be varied uniformly between the limits of 10Hz~55Hz and then resonator shall be measured. It shall fulfill the specifications in Table 1. It shall fulfill the specifications in Table 1. No visible Resonator shall be measured after 3 times' damage and it Mechanical 6.6 random dropping from the height of 100cm shall fulfill the Shock on concrete floor. specifications in Table 1. Lead terminals are immersed up to 2mm from Resistance to resonator’s body in soldering bath of +260℃ It shall fulfill the 6.7 Soldering ±5℃ for 5s±1s and then resonator shall be specifications in Heat measured after being placed in natural Table 1. conditions for 1h. More than 95% of the terminal Lead terminals are immersed up to 2mm from surface of the 6.8 Solderability resonator’s body in soldering bath of +250℃ resonator shall be ±5℃ for 2s±0.5s. covered with fresh solder. (To be continued) 6 PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS Terminal 6.9 Strength Force of 5N is applied to each lead in axial No any visible Terminal damage and it 6.9.1 Pulling direction for 10s±1s. When force of 5N is applied to each lead in shall fulfill the Terminal axial direction,the lead shall folded up 90° specifications in Bending from the axial direction and folded back to the Table1. 6.9.2 axial direction. The speed of folding shall be each 3s Table 1 Item Specification after test Oscillation Frequency Change Δfosc/fosc （%）max. ±0.3 Resonant Impedance Ro（Ω）max. 30 The limits in the above table are referenced to the initial measurements. Http://www.shoulder.cn Page: 4 SHOULDER ELECTRONICS LIMITED 7 PACKAG To protect the products in storage and transportation，it is necessary to pack them（outer and inner package）.On paper pack, the following requirements are requested. 7.1Dimensions and Mark At the end of package, the warning (moisture proof, upward put) should be stick to it. Dimensions and Mark (see below) NO. Name Quantity 1 Inner Box 40 2 Box 2 3 Package 1 4 Adhesive tape 1.2m 5 Label 1 6 Belt 2.9m 7 Certificate of approval 1 7.2 Section of package Package is made of corrugated paper with thickness of 0.8cm.Package has 2 inner boxes, each has 20 inner boxes (each box for plastic bag). 7.3 Quantity of package Per plastic bag 500 pieces Per inner box 3 plastic bag Per package Http://www.shoulder.cn 40 inner boxes Page: 5 SHOULDER ELECTRONICS LIMITED （60000 pieces of piezoelectric ceramic part ） 7.4 Inner box Dimensions 1 Label 2 QC Label 3 Inner Box Pars shall be packaged in box with hold down tape upside. Part No., quantity and lot No. 8 OTHER 8.1 Caution of use 8.1.1 Do not use this product with bend. Please don’t apply excess mechanical stress to the component and terminals at soldering. 8.1.2 The component may be damaged when an excess stress will be applied. 8.1.3 This specification mentions the quality of the component as a single unit. Please insure the component is thoroughly evaluated in your application circuit. 8.2 Notice 8.2.1 Please return one of this specification after your signature of acceptance. 8.2.2 When something gets doubtful with this specifications, we shall jointly work to get an agreement. Http://www.shoulder.cn Page: 6 SHOULDER ELECTRONICS LIMITED