SHOULDER ELECTRONICS LIMITED CERAMIC RESONATOR Data Sheet PRODUCT 产 品: CERAMIC MODEL NO 型 号: ZTT…MT PREPARED 编 制: Fengyu CHECKED 审 核: York APPROVED 批 准: Lijiating DATE Http://www.shoulder.cn 日 期: RESONATOR 2008-01-25 Page: 1 SHOULDER ELECTRONICS LIMITED 1 SCOPE This specification shall cover the characteristics of the ceramic resonator 6.01-13.00MHZ. 2 PART NO. PART NUMBER CUSTOMER PART NO SPECIFICATION NO ZTT…MT 3．OUTLINE DIMENSIONS AND MARK 3.1 Appearance: No visible damage and dirt. 3.2 Construction: Leads are soldered on electrode and body is molded by resin. 3.3 The products conform to the RoHS directive and national environment protection law. 3.4 Dimensions and mark 5.0max 5.0±1.0 10.0max 10.0max 0.5±0.1 ③ ② ① 2.5±0.3 2.5±0.3 0.25±0.1 ①INPUT ②GROUND ③GROUND 4．ELECTRICAL SPECIFICATIONS 4.1 RATING Items Withstanding Voltage (V) Insulation Resistance Ri,（MΩ）min. Operating temperature Storage temperature Rating Voltage Http://www.shoulder.cn Requirement 50 (DC，1min) 100 （10V，1min） -25℃～85℃ -55℃～+85℃ 6V DC UR（V） 15V p-p Page: 2 SHOULDER ELECTRONICS LIMITED 4.2 ELECTRICAL SPECIFICATIONS Items Requirement Oscillation Frequency Fosc（MHz） 6.01-13.00 Frequency Accuracy （%） ±0.5 Resonant Impedance Ro（Ω）max. 25 Temperature Coefficient of Oscillation ±0.3（Oscillation Frequency drift， Frequency （%） max. -25℃～+85℃） Oscillation Frequency ±0.3 (From initial value) Aging Rate (%) max * * Components shall be left in a chamber of +85±2℃ for 1000 hours, then measured after leaving in natural condition for 1 hours. 5．TEST 5.1 Test Conditions Parts shall be tested under the condition ( Temp.：20±15℃,Humidity ：65±20% R.H.) unless the standard condition(Temp.：25±2℃,Humidity ：65±5% R.H.) is regulated to measure. 5.2 Test Circuit IC：1/6TC4069UBP×2 X：CERAMIC RESONATOR C1 C2：CAPACITOR 6 PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS No. 6.1 6.2 6.3 6.4 Item Humidity High Temperature Exposure Low Temperature Exposure Temperature Cycling Http://www.shoulder.cn Performance Requirement Condition of Test Subject the resonator at 40±2℃ and 90%-95% R.H. for 500h, resonator shall be measured after being placed in natural conditions for 1h. Subject the resonator to 85±2℃ for 500h, resonator shall be measured after being placed in natural conditions for 1h. Subject the resonator to -55±2℃ for 500h, resonator shall be measured after being placed in natural conditions for 1h. After temperature cycling of blow table was performed 5 times, resonator shall be measured after being placed in natural conditions for 1h. Page: 3 It shall fulfill Table 1. It shall fulfill Table 1. It shall fulfill Table 1. It shall fulfill Table 1. SHOULDER ELECTRONICS LIMITED Temperature Time –25±3℃ 30±3 min 85±3℃ 30±3 min Subject the resonator to vibration for 2h.Each in x y and z axis with the amplitude of 1.5mm, The Vibration frequency shall be varied uniformly between the limits of 10Hz-55Hz-10Hz and then resonator shall be measured. Resonator shall be measured after 3 times Mechanical random dropping from the height of 1m on Shock concrete floor. Lead terminals are immersed up to 2 mm from Resistance resonator’s body in soldering bath of 260℃±5 to Soldering ℃ for 10s±1s and then resonator shall be Heat measured after being placed in natural conditions for 1h. 6.5 6.6 6.7 It shall fulfill Table 1. No visible damage and it shall fulfill Table 1. It shall fulfill Table 1. More than 95% Lead terminals are immersed up to 2mm from of the terminal Solderability resonator’s body in soldering bath of 250℃±5 surface of the filter ℃ for 3s±0.5s. shall be covered with fresh solder. 6.8 6．ENVIRONMENTAL TEST No. Item 6.9 6.9.1 Terminal Strength Terminal Pulling 6.9.2 Terminal Bending Performance Requirements Condition of Test Force of 5N is applied to each lead in axial direction for 10s±1s. When force of 5N is applied to each lead in axial direction,the lead shall folded up 90 ° from the axial direction and folded back to the axial direction. The speed of folding shall be each 3s. No visible damage and it shall fulfill Table 1. Table 1 Item Oscillation Frequency Change Δfosc/fosc （%）max. Resonant Impedance Specification after test ±0.3 Ro（Ω）max. 25 The limits in the above table are referenced to the initial measurements. Http://www.shoulder.cn Page: 4 SHOULDER ELECTRONICS LIMITED 7．PACKAGE To protect the products in storage and transportation，it is necessary to pack them（outer and inner package）.On paper pack, the following requirements are requested. 7.1 Dimensions and Mark 6 7 4 5 320 1 2 450 NO. ① ② ③ ④ ⑤ ⑥ ⑦ 3 Name Package Box Inner Box Belt Adhesive tape Label Certificate of approval 350 Quantity 1 2 40 2.9 m 1.2 m 1 1 7.2 Section of Package Package is made of corrugated paper with thickness of 0.8cm.Package has 2 boxes, each has 20 inner boxes. 7.3 Quantity of Package Per plastic bag 500 pieces Per inner box 2 plastic bag Per package 40 inner boxes （40000 pieces of piezoelectric ceramic part ） 7.4 Inner Package Http://www.shoulder.cn Page: 5 SHOULDER ELECTRONICS LIMITED ② ③ mm 140mm 3 20 ① 420mm NO. Name Quantity ① Inner package 1 ② Adhesive tape 1.2 m Label 1 ③ 7.5 Inner Box Dimensions ④ ② 52 ① 80 ③ 150 NO. Name Quantity ① Inner Box 1 ② RoHS Label 1 ③ QC Label 1 ④ Label 1 8．OTHER 8.1 Caution 8.1.1 Don’t apply excess mechanical stress to the component and terminals at soldering. Do not use this product with bend. 8.1.2 Do not clean or wash the component for it is not hermetically sealed. 8.1.3 Do not use strong acidity flux，more than 0.2wt% chlorine content，in flow soldering. 8.1.4 Don’t be close to fire. 8.1.5 All kinds of re-flow soldering must not be applied on the component. 8.1.6 This specification mentions the quality of the component as a single unit. Please insure the component is thoroughly evaluated in your application circuit 8.1.7 Expire date (Shelf life) of the products is 12 months after delivery under the conditions of a sealed and an unopened package. Please use the products within six months after delivery. If Http://www.shoulder.cn Page: 6 SHOULDER ELECTRONICS LIMITED you store the products for a long time (more than six months), use carefully because the products may be degraded in the solderability or rusty. Please confirm solderability and characteristics for the products regularly. 8.1.8 Please contact us before using the product as automobile electronic component. 8.2 Notice 8.2.1 Please return one of this specification after your signature of acceptance. 8.2.2 When something gets doubtful with this specifications, we shall jointly work to get an agreement. Http://www.shoulder.cn Page: 7 SHOULDER ELECTRONICS LIMITED