SHOULDER ELECTRONICS LIMITED CERAMIC RESONATOR Data Sheet PRODUCT 产 品: CERAMIC MODEL NO 型 号: ZTT…MG PREPARED 编 制: Fengyu CHECKED 审 核: York APPROVED 批 准: Lijiating DATE Http://www.shoulder.cn 日 期: RESONATOR 2008-01-25 Page: 1 SHOULDER ELECTRONICS LIMITED 1 SCOPE This specification shall cover the characteristics of the ceramic resonator 1.84-6.00MHZ. 2 PART NO PART NUMBER CUSTOMER PART NO SPECIFICATION NO ZTT…MG 3 OUTLINE DRAWING AND DIMENSIONS 3.1 Appearance: No visible damage and dirt. 3.2 Construction: Leads are soldered on electrode and body is molded by resin. 3.3 Except the chip(ceramic element, ceramic base, capacitance slice), the materials don’t contain lead. 3.4 Dimensions 5.0max 10.0max 8.0max ZTT 5.00MG ③ ② 5.0±1.0 0.5±0.1 ① 2.5±0.3 2.5±0.3 0.3±0.1 ① Input ② Ground ③ Output 4 RATING AND ELECTRICAL SPECIFICATIONS 4.1 RATING Items Withstanding Voltage (V) Insulation Resistance Ri,（MΩ）min. Content 50 (DC，1min) 100 （100V，1min） Operating Temperature Range (℃) -20～+80 Storage Temperature Range (℃) -40～+85 Http://www.shoulder.cn Page: 2 SHOULDER ELECTRONICS LIMITED 4.2 ELECTRICAL SPECIFICATIONS Items Oscillation Frequency Fosc（MHz） Frequency Accuracy （%） Resonant Impedance Ro（Ω）max. Temperature Coefficient of Oscillation Frequency （%） max. Rating Voltage UR（V）max. Aging Rate （%）max. Content 1.84-6.00 ±0.5 30 ±0.3（Oscillation Frequency drift，-25℃～+85℃） 6V DC 15V p-p ±0.3 （For Ten Years） 5 MEASUREMENT 5.1 Measurement Conditions. Parts shall be measured under a condition ( Temp.：20±15℃,Humidity ：65±20% R.H.) unless the standard condition(Temp.：25±3℃,Humidity ：65±5% R.H.) is regulated to measure. 5.2 Test Circuit IC：1/6TC4069UBP×2 X：CERAMIC RESONATOR C1 C2：30pF(1±20%) 6 PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS No. 6.1 6.2 6.3 6.4 Item Humidity High Temperature Exposure Low Temperature Exposure Temperature Http://www.shoulder.cn Performance Requirements Condition of Test Subject the resonator at +40 ℃±2℃ and 90%-95% R.H. for 500h, resonator shall be measured after being placed in natural conditions for 1h. Subject the resonator to +85 ℃ ± 5 ℃ for 500h, resonator shall be measured after being placed in natural conditions for 1hr. It shall fulfill the specifications in Table 1. It shall fulfill specifications Table 1. Subject the resonator to –25 ℃ ± 5 ℃ for It shall fulfill 500h, resonator shall be measured after being specifications placed in natural conditions for 1h. Table 1. Subject the resonator to －25℃ for 30 min. It shall fulfill Page: 3 the in the in the SHOULDER ELECTRONICS LIMITED Cycling 6.5 6.6 6.7 6.8 Vibration followed by a high temperature of ＋85℃ for 30 min. Cycling shall be repeated 5 times. Resonator shall be measured after being placed in natural conditions for 1h. Subject the resonator to vibration for 2h each in x y and z axis with the amplitude of 1.5mm, the frequency shall be varied uniformly between the limits of 10Hz-55Hz and then resonator shall be measured. specifications in Table 1. It shall fulfill the specifications in Table 1. No visible damage and it Resonator shall be measured after 3 times' Mechanical random dropping from the height of 100cm shall fulfill the Shock on concrete floor. specifications in Table 1. Lead terminals are immersed up to 2 mm Resistance to from resonator’s body in soldering bath of It shall fulfill the 260℃±5℃ for 5s±1s and then resonator specifications in Soldering shall be measured after being placed in Table 1. Heat natural conditions for 1h More than 95% of the terminal Lead terminals are immersed up to 2mm from surface of the Solderability resonator’s body in soldering bath of 250℃± resonator shall be 5℃ for 2s±0.5s. covered with fresh solder. (To be continued) 6. PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS No. Item Terminal Strength 6.9.1 Terminal Pulling 6.9.2 Terminal Bending Performance Requirements Condition of Test 6.9 Http://www.shoulder.cn Force of 5N is applied to each lead in axial direction for 10s±1s. When force of 5N is applied to each lead in axial direction,the lead shall folded up 90° from the axial direction and folded back to the axial direction. The speed of folding shall be each 3s. Page: 4 No visible damage and it shall fulfill the specifications in Table 1. SHOULDER ELECTRONICS LIMITED Table 1 Item Specification after test Oscillation Frequency Change Δfosc/fosc Resonant Impedance ±0.3 (%) max Ro（Ω）max 30 Note:The limits in the above table are referenced to the initial measurements. 7 PACKAGE To protect the products in storage and transportation，it is necessary to pack them（outer and inner package）.On paper pack, the following requirements are requested. 7.1 Dimensions and Mark At the end of package, the warning (moisture proof, upward put) should be stick to it. Dimensions and Mark (see below) Http://www.shoulder.cn Page: 5 SHOULDER ELECTRONICS LIMITED NO. Name Quantity 1 Inner Box 40 2 Box 2 3 Package 1 4 Adhesive tape 1.2m 5 Label 1 6 Belt 2.9m 7 Certificate of approval 1 Notes 7.2 Section of package Package is made of corrugated paper with thickness of 0.8cm.Package has 2 inner boxes, each has 20 inner box (each box for plastic bag). 7.3 Quantity of package Per plastic bag 500 pieces Per inner box 3 plastic bag Per package （60000 pieces of 40 inner boxes piezoelectric ceramic part ） 7.4 Inner box Dimensions 1 Label 2 QC Label 3 Inner Box Pars shall be packaged in box with hold down tape upside. Part No., quantity and lot No. Http://www.shoulder.cn Page: 6 SHOULDER ELECTRONICS LIMITED 8 OTHER 8.1 Caution of use 8.1.1 Do not use this product with bend. Please don’t apply excess mechanical stress to the component and terminals at soldering. 8.1.2 The component may be damaged when an excess stress will be applied. 8.1.3 This specification mentions the quality of the component as a single unit. Please insure the component is thoroughly evaluated in your application circuit. 8.2 Notice 8.2.1 Please return one of this specification after your signature of acceptance. 8.2.2 When something gets doubtful with this specifications, we shall jointly work to get an agreement. Http://www.shoulder.cn Page: 7 SHOULDER ELECTRONICS LIMITED