OPL611 - Eurocomposant

SMD Photologic® Sensor
OPL611 Through OPL615
Features:
• High noise immunity
• Small Package Outline: 3mm x 3mm (H = 1mm)
• Choice of two device types:
•
•
•
•
1. Buffer
2. Inverter
Choice of two output options with each device type:
1. Open Collector
2. 10K Pull-Up
Direct TTL/LSTTL CMOS interface
Data rates to 250kBaud
Vcc from 4.5 to 16VDC
Description:
The OPL611 – OPL615 is a low cost, small surface mount packaged photo light sensor with a digital output
suitable for applications with limited space such as portable applications. All devices in the series have a
Photologic® chip that is encapsulated in a molded plastic surface mount package, which provides optical coupling
combined with mechanical protection. The hysteresis characteristics of the Schmitt trigger on each device offers
high immunity to noise on input and VCC. There are two output options for both the buffer and inverter versions,
and all operate with a power supply voltage range from 4.5V to 16V.
• OPL611 through OPL615: Are mechanically and spectrally matched to the OP180, OP200,
OP250 series, OP270 series and OP280 series LED’s.
*Contact your OPTEK sales representatives for those special requirements to meet your needs.
Applications:
•
•
•
•
•
•
•
•
•
Base Part
Number
Encoder
Non-contact reflective object sensor
Package
Output Type - With Light
Minimum Input
Power Range
Buffer (Internal) 10K Pull-Up
OPL611
Non-contact interruptive sensing
Assembly line automation
Machine automation
Machine safety
End of travel sensor
OPL612
SMD
Buffer Open Collector
OPL614
(DFN6L)
Inverter (Internal) 10K Pull-Up
2
1.0 (mW/cm )
Inverter Open Collector
OPL615
Note: Buffer = Output is high with light.
Inverter = Output is low with light.
Object sensor
Paper sensor
(RoHS)
(Level-3)
(Human Body Model)
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue A 12/09
Page 1 of 8
SMD Photologic® Sensor
OPL611 Through OPL615
Block Diagram
Buffer
Open
Collector
Buffer
10K
Pull-Up
Inverter
Open
Collector
Inverter
10K
Pull-Up
(Note: BUFFER = Output is high with light. INVERTER = Output is low with light.)
Absolute Maximum Ratings
Maximum Operating Conditions (TA=25°C unless otherwise noted)
DC Supply Voltage (VCC)
4.5V to18V
Operating Temperature Range
-40°C to + 85°C
Storage Temperature Range
-55°C to + 100°C
ICC
10mA
Power Dissipation
(1)
90mW
Sinking Current
25mA
Voltage at Output Lead (OPL612 and OPL615)
Duration of Output Short to VCC or Ground
Irradiance
(2)
30V
1 second
3mW/cm2
ESD (Human Body Model)
5KV
Notes:
(1) Derate linearly 1.0mW/°C above 25° C
(2) Irradiance measurements are made with, λ = 890nm.
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue A 12/09
Page 2 of 8
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
SMD Photologic® Sensor
OPL611 Through OPL615
Electrical Characteristics
Electrical Characteristics (TA = 25°C unless otherwise noted) (Light Source: λ = 890nm +/-10nm)
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
TEST CONDITIONS
-
VCC
Operating Supply Voltage
4.5
-
16
V
ICC
Supply Current
1.0
3.8
7
mA
Positive-Going
Threshold Irradiance
0.15
0.25
0.40
1.1
1.4
1.6
-
-
-0.6
-
%/°C
-
V
EeT(+)
EeT(+)/EeT(-) Hysteresis Ratio
∆Eet(+)
(∆T)
Temperature Co-efficient
mW/cm2 VCC = 5V
VCC = 5V
V CC = 5V, -40°C to +85°C
VCC = 4.5V to 16V, IOH = -100µA
Ee = 3mW/cm2 (OPL611)
Ee = 0mW/cm2 (OPL614)
VOH
High Level Output Voltage
VOL
Low Level Output Voltage
-
300
400
mV
VCC = 4.5V to 16V, IOL = 16mA
Ee = 0mW/cm2 (OPL611 and OPL612)
Ee = 3mW/cm2 (OPL614 and OPL615)
IOH
High Level Output Current
-
-
10
µA
VCC = 16V, VOUT = 30V
Ee = 3mW/cm2 (OPL612)
Ee = 0mW/cm2 (OPL615)
tr
Output Rise Time
-
90
-
ns
VCC = 5V, Freq. = 100kHz,
R = 1K, C <10pF, Ee = 3mW/cm2.
Decouple Cap (VCC to GND) = 0.1uF
tf
Output Fall Time
-
50
-
ns
VCC = 5V, Freq. = 100kHz,
R = 1K, C <10pF, Ee = 3mW/cm2.
Decouple Cap (VCC to GND) = 0.1uF
-
0.4
-
µs
VCC = 5V, Freq. = 100kHz,
R = 1K, C <10pF, Ee = 3mW/cm2.
Decouple Cap (VCC to GND) = 0.1uF
-
1.6
-
µs
VCC = 5V, Freq. = 100kHz,
R = 1K, C <10pF, Ee = 3mW/cm2.
Decouple Cap (VCC to GND) = 0.1uF
tpEeT(+)
tpEeT(-)
Propagation Delay
(Low to High)
Propagation Delay
(High to Low)
VCC -2 VCC -1
VCC = 4.5V to 16V
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue A 12/09
Page 3 of 8
SMD Photologic® Sensor
OPL611 Through OPL615
OPL600 Series
(Package Outline)
TOP VIEW
SOLDER PAD LAYOUT
Pin Function
1
Vcc
2
Vout
3
GND
4
NC
5
NC
6
NC
Note(s):
Dimensions are in millimeters.
If used, connect heat sink pad to GND.
ESD rating is the human body model.
Moisture rating is level 3.
SIDE VIEW
Handling Considerations (see Application Bulletin 237)
SOLDER PROFILE
To combat moisture, Optek bakes all our devices in a 100°C environment for 24 hours prior to inserti ng
them into the shipping tubes and sealing them in airtight bags. Once removing parts from their shipping
bags, customers are strongly encouraged to solder the devices within four (4) hours. Exposing the parts to
humidity for longer than four (4) hours prior to soldering will require the customer to subject the parts to a 24
hour bake at 100°C prior to use. If the parts will experience future soldering operations, housing the parts
in a dry box or similar environment is encouraged. Also, it is acceptable to bake the parts multiple
times if there are multiple soldering operations and a dry environment cannot be maintained. Once all
soldering operations are completed, exposing the parts to humidity is acceptable.
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue A 12/09
Page 4 of 8
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
SMD Photologic® Sensor
OPL611 Through OPL615
Reliability Test Results
Stress results
Test
Test Conditions
Device
Hrs./Cycles
Devices
Tested
Average
Degrad %
Failures(1)
Operating Life (OL)
TA = 25°C, I F = 20mA, 1008 hrs
1099 hrs
40
ICC = 0.6%;
I(OL) = -1.4%
0
High Temperature Operating
Life (HTOL)
TA = 85°C; 1008 hrs; Vcc = 18V
1008 hrs
20
ICC = 0.6%;
I(OL) = -1.4%
0
High Temperature Storage
(HT)
TH = 105°C; 1008 hrs
1008 hrs
26
ICC = 0.6%;
I(OL) = -1.4%
0
Low Temperature Storage
(LT)
TL = -40°C; 1008 hrs
1008 hrs
24
ICC = 0.4%;
I(OL) = -0.8%
0
HAST—unbiased /
Temperature & Humidity
85°C/85% R.H.; 168 hrs
168 hrs
20
ICC = 0.4%
I(OL) = -0.006%
0
Air-to-Air Thermal Shock (I)
-40°C to 105°C, 6 sec transfer
rate, 10 min extremes
100 cycles
25
ICC = 0.46%;
I(OL) = -4.79%
0
100 cycles
25
ICC = -3.55%;
I(OL) = -3.82%
0
Air-to-Air Thermal Shock (II)
-55°C to 125°C, 6 sec transfer
rate, 10 min extremes
Notes:
(1) End point failure criteria is catastrophic failure or if coupled sensitivity changes by greater than 50%.
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue A 12/09
Page 5 of 8
SMD Photologic® Sensor
OPL611 Through OPL615
Reel and Tape Information
(All dimensions are in millimeters.)
REEL
TAPE
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue A 12/09
Page 6 of 8
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
SMD Photologic® Sensor
OPL611 Through OPL615
Issue
A
Change Description
Initial Release
Approval
Date
W. Chalmers
12/2009
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue A 12/09
Page 7 of 8