MINT1180 180W Single Output Medical Series Features 3” x 5” x 1.3” Package 180W Convection Cooled Power Ideal for 1U Applications Class I and Class II versions Universal Input 90-264 VAC Approved to CSA/EN/IEC/UL60601-1, 3rd Edition, 2 x MOPP Isolation Approved to CSA/EN/IEC/UL60950-1 2nd Edition Efficiency 90% typical 3 Year Warranty RoHS Compliant Description The MINT1180 product family is the most cost-effective medically approved supply in the market with 180 watts of convection cooled output power in 3”X5” footprint. The series comes in eight different models ranging from 12 to 48V and has been approved to IEC60601-1 3rd Edition, rated for 2 MOPP (Means of Patient Protection) isolation. This new single output power supply family has both Class I and II input versions and accepts wide input range of 90 to 264Vac. The typical 90% efficiency and convection cooled make this supply an excellent solution for HomeCare applications where the use of fans is not desired. Model Selection Model Number Volts Output Current* Minimum Load Ripple & Noise** Total Regulation OVP Threshold MINT1180A1275K01 12V 15.0A 0A 120mV pk-pk ±3% 14.0 ± 1.1V MINT1180A1575K01 15V 12.0A 0A 150mV pk-pk ±3% 18.5 ± 1.2V MINT1180A1875K01 18V 10.0A 0A 180mV pk-pk ±3% 21.5 ± 2.0V MINT1180A2475K01 24V 7.50A 0A 240mV pk-pk ±3% 29.0 ± 2.5V MINT1180A2875K01 28V 6.40A 0A 280mV pk-pk ±3% 33.5 ± 2.5V MINT1180A3275K01 32V 5.62A 0A 320mV pk-pk ±3% 36.0 ± 3.0V MINT1180A4875K01 48V 3.75A 0A 480mV pk-pk ±3% 56.0 ± 3.0V Notes: * Total convection power is 180 Watts. ** Measured with noise probe directly across output terminals, and load terminated with 0.1µF ceramic and 10µF low ESR capacitors. General Specifications AC Input Input Current www.slpower.com 100-240Vac, ±10%, 47-63Hz, 1∅ 120–370Vdc Turn On Time Less than 3 sec. @115Vac & Full Load 115Vac: 1.8A, 230Vac: 0.9A Hold-up Time >16mS at 180W, 120Vac MINT1180 REV 1.8, 15-OCT-13 1 MINT1180 180W Single Output Medical Series General Specifications (continued) Inrush Current Input Fuses Earth Leakage Current Efficiency Output Power Transient Response Signals 264Vac, cold start: will not exceed 55A Overload Protection F1, F2: 4.00A, 250VAC fuses provided on all models Short Circuit Protection <275µA@264Vac, 60Hz, NC; <400µA SFC Overvoltage Protection 88% typical Switching Frequency 180W convection cooled 500µS typ. for return to within 0.5% of nominal, 50% load step. ∆i/∆t <0.2A/µS. Max Volt Deviation = 3% Isolation N/A 120%-150% of rating, Hiccup Mode Provided - no damage will occur if the output is shorted, auto recovery OVP latch at 110%-130% of rated output voltage. PFC: Fixed, 65kHz Main Converter: Variable 35-200kHz, 65-70kHz at full load. Input-Output: 4000Vac, 2 x MOPP Input-Ground: 1800Vac, 1 x MOPP Output-Ground: 1500Vac Ripple and Noise See chart Operating Temperature -10°C to +70°C Start Up at -40°C, full load Output Voltage See chart Temperature Derating Derate output power linearly above 50°C to 50% at 70°C Voltage Adjustability Fixed output Storage Temperature -40°C to +85°C Minimum Load Not required Altitude Total Regulation +/- 3% combined line, load and initial setting. Vibration Operating: 0.003g²/Hz, 1.5grms overall, 3 axes, 10 min/axis Non-Operating: 0.026g²/Hz, 5.0grms overall, 3 axes, 1 hr/axis Dimensions Weight Relative Humidity Shock Safety Standards W: 3.0” x L: 5.0” x H: 1.3” MTBF 325g Operating: -500 to 10,000 ft. Non-operating: -500 to 40,000 ft. 5% to 95%, non-condensing Operating: Half-sine, 20gpk, 10ms, 3 axes, 6 shocks total Non-Operating: Half-sine, 40 gpk, 10 ms, 3 axes, 6 shocks total EN/CSA/UL/IEC 60601-1, 3rd Edition EN/CSA/UL/IEC 60950-1, 2nd Edition 214,194 hours, 25°C, 110Vac Output vs. Temperature Derating Curve 180W convection cooled, derate output power to 50% at 70°C. Output Power (W) 200 150 100 50 0 -10 0 Convection www.slpower.com 10 20 30 40 50 60 70 Temperature (°C) MINT1180 REV 1.8, 15-OCT-13 2 MINT1180 180W Single Output Medical Series EMI/EMC Compliance Conducted Emissions EN55011/22 Class B, FCC Part 15, Subpart B, Class B Radiated Emissions EN55011/22; FCC Part 15, Class A with 6dB Margin Static Discharge Immunity EN61000-4-2, Criteria A, 6kV Contact Discharge, 8kV air discharge Radiated RF Immunity EN61000-4-3, 3V/m. Criteria A. EFT/Burst Immunity EN61000-4-4, 2kV/5kHz, Criteria A Line Surge Immunity EN61000-4-5, 1kV differential, 2kV common-mode, Criteria A Conducted RF Immunity EN61000-4-6, 3Vrms, Criteria A Power Frequency Magnetic Field Immunity EN61000-4-8, 3A/m, Criteria A Voltage Dip Immunity EN61000-4-11, 5% Vnom: 0.5cycle; 40% Vnom: 5 cycles, 70% Vnom: 25 cycles, Criteria A Line Harmonic Emissions EN61000-3-2, Class A, B, C, & D Flicker Test EN61000-3-3, Complies (dmax<6%) Mechanical Drawing Notes: 1. All dimensions in inches (mm), tolerance is +/-0.000”. 2. Mounting holes should be grounded for EMI purposes. 3. FG is safety ground connection. 4. The power supply requires mounting on metal standoffs 0.20” (5mm) in height, min. [4] x 0.156 4 PLCS MTG HOLES Connector Information Input Connector J100 Ground (FG) DC Output Connector J300 PIN 1) AC LINE PIN 2) EMPTY PIN 3) AC NEUTRAL 0.25” FASTON TAB Term. 1,2,3: RTN Term. 4,5,6: +Vout Mating Connector: AMP 640250-3 Pins: 640252-2 Mating Connector: Molex 190020001 Mating Connector: AMP 640250-6 Pins: 640252-2 Data Sheet © 2013 SL Power Electronics Corp. The information and specifications contained herein are believed to be correct at the time of publication. However, SL Power accepts no responsibility for consequences arising from reproduction errors or inaccuracies. Specifications are subject to change without notice. www.slpower.com MINT1180 REV 1.8, 15-OCT-13 3