specific technical criteria

Issue Date:
2007-01-23
Page 4 of 57
Report Reference #
E116994-A34-UL-1
SPECIFIC TECHNICAL CRITERIA
TEST REPORT
UL 60601-1
Medical Electrical Equipment
Part 1: General requirements for safety
Report Reference No ........................: E116994-A34-UL-1
Compiled by .....................................: Ahmad Daoudi
Reviewed by ....................................: Elizabeth Drew
Date of issue ....................................: 2007-01-23
Standards .........................................: UL 60601-1, 1st Edition, 2006-04-26 (Medical Electrical Equipment,
Part 1: General Requirements for Safety)
CAN/CSA-C22.2 No. 601.1-M90, 1st Edition, 2003-11 (Medical
Electrical Equipment - Part 1: General Requirements for Safety)
Test procedure .................................: Component Recognition
Non-standard test method ...............: N/A
Test item description .......................: Switching Power Supplies
Trademark ........................................:
Model and/or type reference ............: GLM65X-YYY G and G2M65X-YYY G Series where X is any alpha
character, "A" through "Z", which represents various output voltage
configuration. -YYY is any numeric value 000-999 which represents
value added options not related to safety. May or may not be followed
by an optional “G” which indicates compliance to RoHS. (RoHS
compliance has not been evaluated by UL.)
Rating(s) ...........................................: Input: 100-240 V ac, 50/60 Hz, 2.0 A
Output: GLM65 and G2M65 Models
Output #
#1
#2
#3
Voltage
[V dc]
3.3 to 5
3.3 to 24
-15 to 12
Convection Cool
Max [A]
7
4
2.5
150 LFM
Max [A]
9
6
4
70 W max with a min. of 150 LFM airflow over unit;
60 W max convection cooled.
Output: G2M65A-111 G
Convection
Volts [dc]
Amps
Output #1
5.6
5 max
Output #2
12.8
3 max
Output #3
-12.8
1 max
60 W max convection cooled.
TRF No.: IEC60601_1C
Underwriters Laboratories Inc.
Issue Date:
2007-01-23
TRF No.: IEC60601_1C
Page 5 of 57
Report Reference #
Underwriters Laboratories Inc.
E116994-A34-UL-1
Issue Date:
2007-01-23
Page 6 of 57
Report Reference #
E116994-A34-UL-1
GENERAL INFORMATION
Test item particulars (see also clause 5):
Classification of installation and use ......................... :
Permanently installed
Supply connection ..................................................... :
Permanently installed
Accessories and detachable parts included in the
evaluation .................................................................. :
None
Options included ....................................................... :
None
Possible test case verdicts:
- test case does not apply to the test object ............. :
N/A
- test object does meet the requirement ................... :
P(Pass)
- test object does not meet the requirement ............. :
F(Fail) (acceptable only if a corresponding, less
stringent national requirement is "Pass")
Abbreviations used in the report:
- normal condition ............................................ :
N.C. - single fault condition ................ :
S.F.C.
- operational insulation ..................................... :
OP
- basic insulation ........................ :
BI
- basic insulation between parts of opposite
polarity:
BOP - supplementary insulation ......... :
SI
- double insulation ............................................ :
DI
RI
- reinforced insulation ................ :
General remarks:
- "(see Enclosure #)" refers to additional information appended to the Test Report
- "(see appended table)" refers to a table appended to the Test Report
- Throughout the Test Report a point is used as the decimal separator
General Product Information:
CA1.0
Report Summary
CA1.1
N/A
CB1.0
Product Description
CB1.1
The equipment (DC power supplies) covered by this report, are components, which are intended
for use in end-product equipment used in a hospital or related health care facility, evaluated to
standard Medical Equipment.
CC1.0
Model Differences
CC1.1
The GLM65X-YYY G Series models are Class I power supplies and are similar to each other and
differ only on secondary circuitry. The G2M65X-YYY G Series models are Class II power
supplies and are similar to each other and differ only on secondary circuitry.
Differences between Class I and Class II models:
Components C4, C8, W1, W3 and Ground Tab are provided in Class I models and are not
TRF No.: IEC60601_1C
Underwriters Laboratories Inc.
Issue Date:
2007-01-23
Page 7 of 57
Report Reference #
E116994-A34-UL-1
provided in class II models. Components W2, C20 and C23 are provided in class II models and
are not provided in class I models.
GLM65X-YYY G and G2M65X-YYY G Series where X is any alpha character, "A" through "Z",
which represents various output voltage configurations. Models may or may not be followed by
suffix -YYY and/or “G”, where -YYY may be any number from 000 thru 999. The -YYY suffix is
used for value added configurations that have no impact on safety and suffix “G” indicates
compliance to RoHS.
CD1.0
Additional Information
CD1.1
This Report is issued based on testing conducted on Models GLM65A, GLM65B, GLM65D,
GLM65E, GLM65G, and GLM65H to represent the entire series, and the results from UL CB
Report No. E116994-V1-S68, Issued: 2003 July 29. IN addition, the following models were
tested for this re-issue. G2M65A, G2M65B, G2M65D, G2M65E, G2M65G, G2M65H, G2M65A111G
The schematics for these models are kept on file at the CB Testing Laboratory mentioned in the
first page of this test report, and can be provided by the applicant upon request by CBTLs.
CE1.0
Technical Considerations
CE1.1
The product was investigated to the following
additional standards:
CAN/CSA C22.2 No. 601.1-M90 (R1997),
CAN/CSA C22.2 No. 601.1S1-94, and
CAN/CSA C22.2 No. 601.1B-98 (National
Differences for Canada), EN 60601-1: 1990 +
A1:1993 + A2:1995 + A13:1996 (except EMC
limitations, EN 60601-1-2, Biocompatibility, EN
10993-1, Programmable Electronic Systems,
IEC 60601-1-4),
CE1.2
The product was not investigated to the
following standards or clauses:
Clause 52.1, Programmable Electronic Systems
(IEC 601-1-4), Clause 48, Biocompatibility (ISO
10993-1), Clause 36, Electromagnetic
Compatibility (IEC 601-1-2)
CE1.3
The product is Classified only to the following
hazards:
Shock, Fire,
CE1.4
The degree of protection against harmful
ingress of water is:
Ordinary
CE1.6
The mode of operation is:
Continuous
CE1.7
Software is relied upon for meeting safety
requirements related to mechanical, fire and
shock:
No
CE1.8
The product is suitable for use in the presence
of a flammable anesthetics mixture with air or
oxygen or with nitrous oxide:
No
CF1.0
Engineering Conditions of Acceptability
TRF No.: IEC60601_1C
Underwriters Laboratories Inc.
Issue Date:
CF1.1
2007-01-23
Page 8 of 57
Report Reference #
E116994-A34-UL-1
For use only in or with complete equipment where the acceptability of the combination is
determined by Underwriters Laboratories Inc.
When installed in an end-product, consideration must be given to the following:
CF2.0
The power supplies covered by this report are
components intended for use in end-product
equipment which are used in a hospital or
related health care facility.
--
CF2.1
The power supplies have been judged on the
basis of the required spacings in the Second
Edition of the Standards for Medical Electrical
Equipment, Part 1: General Requirements for
Safety, UL 60601-1, which covers the end use
product for which the component is designed.
--
CF2.2
The component shall be installed in compliance -with the enclosure, mounting, spacing, casualty
markings and segregation requirements of the
end-use application.
CF2.3
Consideration should be given to measuring the -temperature on power electronic components
and transformer windings when the power
supply is installed in the end-use equipment.
CF2.4
The input/output connectors are not acceptable -for field connections, they are only intended for
connection to mating connectors of internal
wiring inside the end-use equipment.
CF2.5
The output circuits have not been evaluated for -direct patient connection (Type B, BF or CF).
CF2.6
The GLM65 power supplies are class I
components and should be properly bonded to
ground in the end-use equipment.
--
CF2.7
The Temperature Test was performed in a
raised ambient of 50°C.
--
CF2.8
Transformer T2 uses a UL R/C (OBJY2) Class
H (180) insulation system, and transformer T3
uses UL R/C (OBJY2) Class F (155°C)
insulation system.
--
CF2.9
Leakage current testing should be repeated in
the end product application.
--
CF3
The power supply was evaluated as Reinforced -insulation between primary and secondary on
the GLM65 and G2M65 series; basic Insulation
between primary to ground on the GLM65
series only. Primary to ground on the G2M65 is
considered reinforced insulation.
CF3.1
The GLM65 Series of power supplies has been -evaluated as Class I, and the G2M65 Series of
TRF No.: IEC60601_1C
Underwriters Laboratories Inc.
Issue Date:
2007-01-23
Page 9 of 57
Report Reference #
power supplies has been evaluated as Class II.
All these power supplies are evaluated as
continuous operation, ordinary equipment and
have not been evaluated for use in the
presence of a flammable anesthetic mixture
with air, oxygen, or nitrous oxide.
CF3.2
These power supplies have been evaluated for
patient care equipment, but not patient
connected.
--
CF3.3
Under normal and single fault conditions, the
outputs do not exceed 25 V ac or 60 V dc.
--
CF3.4
Double fusing in the end-product should be
considered since primary fusing of both sides
on the mains supply lines was not provided.
--
CF3.5
On the G2M series, the secondary may be
bonded to protective ground in the end use
application, provided the segregation from
protective ground to the primary is maintained.
--
CF3.6
On the G2M series, it is recommended that
-plastic standoffs (of sufficient length) and
attaching hardware be used to provide
segregation from the primary to any protectively
earthed mounting surface.
TRF No.: IEC60601_1C
Underwriters Laboratories Inc.
E116994-A34-UL-1