Data Sheet - System Sensor

Selectable-Output
Low Frequency
Sounder and Low
Frequency Sounder
Strobes for Wall
Applications
SpectrAlert® Advance audible visible notification products
are rich with features guaranteed to cut installation times
and maximize profits.
Features
• 520 Hz ± 10% square wave tone
• Plug-in design with minimal intrusion into the back box
• Tamper-resistant construction
• F
ield-selectable candela settings on wall units: 135, 150, 177, and 185
• Rotary switch for low frequency sounder tone
• Universal mounting plate for wall units
• M
ounting plate shorting spring checks wiring continuity before
device installation
• Electrically compatible with legacy SpectrAlert devices
• Compatible with MDL3 sync module
• Listed for ceiling or wall mounting
The SpectrAlert Advance series offers the most versatile
and easy-to-use line of low frequency sounder and low frequency
sounder strobes in the industry. With white and red plastic housings,
dual listed for wall and ceiling mounting, SpectrAlert Advance can
meet virtually any application requirement.
The wall-mount low frequency sounder, and low frequency sounder
strobes were designed to address the NFPA 72 sleeping space
requirements that require a low frequency notification appliance that
operates within frequency range of 520 Hz ± 10% and is of a square
wave tone. Like the entire SpectrAlert Advance product line they
include a variety of features that increase their application versatility
while simplifying installation. All devices feature plug-in designs
with minimal intrusion into the back box, making installations fast
and foolproof while virtually eliminating costly and time-consuming
ground faults.
To further simplify installation and protect devices from construction
damage, SpectrAlert Advance utilizes a universal mounting plate
with an onboard shorting spring, so installers can test wiring
continuity before the device is installed.
Installers can also easily adapt devices to a suit a wide range of
application requirements using field-selectable candela settings,
automatic selection of 12- or 24-volt operation, and a rotary switch
for 520 Hz low frequency sounder tones.
Agency Listings
S4011 (sounder)
S5512 (strobes)
3047563
MEA452-05-E
7135-1653:0223
7125-1653:0224
SpectrAlert Advance Specifications
Architect/Engineer Specifications
General
SpectrAlert Advance low frequency sounder and low frequency sounder strobes shall mount to a standard 4 × 4 × 1½-inch back box, 4-inch
octagon back box, or double-gang back box. Two-wire products shall also mount to a single-gang 2 × 4 × 17⁄8-inch back box. A universal
mounting plate shall be used for mounting products. The notification appliance circuit wiring shall terminate at the universal mounting plate.
Also, SpectrAlert Advance products, when used with the Sync•Circuit™ Module accessory, shall be powered from a non-coded notification
appliance circuit output and shall operate on a nominal 12 or 24 volts. When used with the Sync•Circuit Module, 12-volt-rated notification
appliance circuit outputs shall operate between 8.5 and 17.5 volts; 24-volt-rated notification appliance circuit outputs shall operate between
16.5 and 33 volts. Indoor SpectrAlert Advance products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or fullwave rectified unfiltered power supply. Low Frequency Sounder strobes shall have field-selectable candela settings including 135, 150, 177,
and 185. The field selectable tones will sound within the frequency range of 520 Hz ±10% square wave tone and have a permanent marking
on the housing that reads “low frequency sounder”.
Low Frequency Sounder
The low frequency sounder shall be a System Sensor SpectrAlert Advance Model _______ listed to UL 464 and shall be approved for fire
protective service. The low frequency sounder and the Sync•Circuit™ MDL3 Module accessory, if used, shall be powered from a notification
appliance circuit output and shall operate on a nominal 12 or 24 volts (includes fire alarm panels with built in sync). When used with the
Sync•Circuit Module MDL3, 12-volt rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts; 24-volt rated
notification appliance circuit outputs shall operate between 16.5 to 33 volts. If the notification appliances are not UL 9th edition listed with
the corresponding panel or power supply being used, then refer to the compatibility listing of the panel to determine maximum devices on
a circuit. The low frequency sounder has an option to switch between temporal three pattern, non-temporal (continuous) pattern and coded
supply within the frequency range of 520Hz ± 10% square wave tone. The low frequency sounder shall operate on a coded or non-coded
power supply.
Low Frequency Sounder Strobe Combination
The low frequency sounder strobe shall be a System Sensor SpectrAlert Advance Model _______ listed to UL 1971 and UL 464 and shall be
approved for fire protective service. The low frequency sounder strobe shall be wired as a primary-signaling notification appliance and comply
with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe’s entire operating
voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. The sounder shall have an option to
switch between a temporal three pattern and a non-temporal (continuous) pattern. These options are set by a multiple position switch. The low
frequency sounder on low frequency sounder strobe models shall operate on a non-coded power supply. The field selectable tones will sound
within the frequency range of 520 Hz ±10% square wave tone.
Synchronization Module
The module shall be a System Sensor Sync•Circuit model MDL3 listed to UL 464 and shall be approved for fire protective service. The module
shall synchronize SpectrAlert strobes at 1 Hz and low frequency sounder at temporal three. Also, while operating the strobes, the module
shall silence the low frequency sounder on low frequency sounder strobe models over a single pair of wires. The module shall mount to a
411 ⁄ 16 × 411 ⁄ 16 × 21 ⁄ 8-inch back box. The module shall also control two Style Y (class B) circuits or one Style Z (class A) circuit. The module shall
synchronize multiple zones. Daisy chaining two or more synchronization modules together will synchronize all the zones they control. The
module shall not operate on a coded power supply.
Physical/Electrical Specifications
Standard Operating Temperature
Humidity Range
Frequency Range
Strobe Flash Rate
Nominal Voltage Low Frequency Sounder
Nominal Voltage Range Low Frequency Sounder Strobe
Operating Voltage Range
Operating Voltage Range MDL3 Sync Module
Input Terminal Wire Gauge
Wall-Mount Dimensions (including lens)
32°F to 120°F (0°C to 49°C)
10 to 93% non-condensing
520 Hz ± 10%
1 flash per second
Regulated 12 DC/FWR or regulated 24 DC/FWR1
Regulated 24 VDC/FWR1
8 to 17.5 V (12 V nominal) or 16 to 33 V (24 V nominal)
8.5 to 17.5 V (12 V nominal) or 16.5 to 33 V (24 V nominal)
12 to 18 AWG
6.4 inches L x 4.7 inches W x 2.5 inches D (162 mm L x 119 mm W x 64 mm D)
Sounder Dimensions
5.6 inches L × 4.7 inches W × 1.3 inches D (142 mm L × 119 mm W × 33 mm D)
Low Frequency Sounder/Strobe with Surface Mount Back Box
6.4 inches L x 4.7 inches W x 4.3 inches D Dimensions (SBBR, SBBW)
(162 mm L x 120 mm W x 108 mm D)
Low Frequency Sounder with Surface Mount Back Box Dimensions 5.7 inches L x 4.8 inches W x 3 inches D (SBBR, SBBW)
(145 mm L x 120 mm W x 76 mm D)
Notes:
1. Full Wave Rectified (FWR) voltage is a non-regulated, time-varying power source that is used on some power supply and panel outputs.
UL Current Draw Data
UL Max. Low Frequency Sounder Current Draw (mA RMS)
8–17.5 Volts
Sound Pattern
dB
DC
Temporal 3
High
191
Continuous
High
292
Coded
High
292
FWR
262
384
388
16–33 Volts
DC
138
138
153
FWR
166
208
205
UL Max. Current Draw (mA RMS), 2-Wire Low Frequency Sounder Strobe, High Candela Range
16–33 Volts
DC Input
135
150
177
185
FWR Input
Temporal 3
277
292
325
344
Temporal 3
Continuous
337
362
387
417
Continuous
16–33 Volts
135
150
296
309
393
395
Low Frequency Sounder Tones and Sound Output Data
Low Frequency Sounder and Low Frequency Sounder Strobe Output (dBA)
Switch Position
1
2
3†
†
Sound Pattern
Temporal 3
Continuous
Coded
8–17.5
Volts
DC FWR
76 76
80 80
80 80
16–33
Volts
DC FWR
76 76
80 80
80 80
Sounder ratings provided are for continuous voltage as provided by the NAC
24-Volt Nominal
Reverberant
DC
FWR
76
76
80
80
80
80
Anechoic
DC FWR
86 86
90 90
90 90
177
343
432
185
351
433
SpectrAlert Advance Dimensions
2.5 in.
4.7 in.
1.3 in.
4.7 in.
5.6 in.
6.4 in.
Wall-mount low frequency sounder strobes
Wall-mount low frequency sounder
SpectrAlert Advance Ordering Information
Model
Wall Low Frequency Sounder Strobes
P2RH-LF
P2WH-LF
Low Frequency Sounders
HR-LF
HW-LF
Accessories
SBBR
SBBW
TR-HS
Description
2-Wire Low Frequency Sounder Strobe, High cd, Red
2-Wire Low Frequency Sounder Strobe, High cd, White
Low Frequency Sounder, Red
Low Frequency Sounder, White
Surface Mount Back Box, Wall, Red
Surface Mount Back Box, Wall, White
Trim Ring, Wall, Red
Notes:
“High cd” refers to strobes that include 135, 150, 177, and 185 candela settings.
3825 Ohio Avenue • St. Charles, IL 60174
Phone: 800-SENSOR2 • Fax: 630-377-6495
www.systemsensor.com
©2015 System Sensor.
Product specifications subject to change without notice. Visit systemsensor.com
for current product information, including the latest version of this data sheet.
AVDS16404 • 1/15