TJA1028 LIN transceiver with integrated voltage regulator Rev. 4 — 25 July 2012 Product data sheet 1. General description The TJA1028 is a LIN 2.0/2.1/SAE J2602 transceiver with an integrated low-drop voltage regulator. The voltage regulator can deliver up to 70 mA and is available in 3.3 V and 5.0 V variants. TJA1028 facilitates the development of compact nodes in Local Interconnect Network (LIN) bus systems. To support robust designs, the TJA1028 offers strong ElectroStatic Discharge (ESD) performance and can withstand high voltages on the LIN bus. In order to minimize current consumption, the TJA1028 supports a Sleep mode in which the LIN transceiver and the voltage regulator are powered down while still having wake-up capability via the LIN bus. The TJA1028 comes in an SO8 package, and also in a 3 mm 3 mm HVSON8 package that reduces the required board space by over 70 %. This feature can prove extremely valuable when board space is limited. 2. Features and benefits LIN 2.0/2.1/2.2 compliant SAE J2602 compliant Downward compatible with LIN 1.3 Internal LIN slave termination resistor Voltage regulator offering 5 V or 3.3 V, 70 mA capability 2 % voltage regulator accuracy over specified temperature and supply ranges Voltage regulator output undervoltage detection with reset output Voltage regulator is short-circuit proof to ground Voltage regulator stable with ceramic, tantalum and aluminum electrolyte capacitors Robust ESD performance; 8 kV according to IEC61000-4-2 for pins LIN and VBAT Pins LIN and VBAT protected against transients in the automotive environment (ISO 7637) Very low LIN bus leakage current of < 2 A when battery not connected LIN pin short-circuit proof to battery and ground Transmit data (TXD) dominant time-out function Thermally protected Very low ElectroMagnetic Emission (EME) High ElectroMagnetic Immunity (EMI) Typical Standby mode current of 45 A Typical Sleep mode current of 12 A LIN bus wake-up function K-line compatible Available in SO8 and HVSON8 packages TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator Leadless HVSON8 package (3.0 mm 3.0 mm) with improved Automated Optical Inspection (AOI) capability Dark green product (halogen free and Restriction of Hazardous Substances (RoHS) compliant) 3. Ordering information Table 1. Ordering information Type number Package Name Description Version TJA1028T/xxx/xx[1][2] SO8 plastic small outline package; 8 leads; body width 3.9 mm SOT96-1 TJA1028TK/xxx/xx[1][2] HVSON8 plastic thermal enhanced very thin small outline package; no leads; 8 terminals; body 3 3 0.85 mm SOT782-1 [1] TJA1028T/5V0/xx and TJA1028TK/5V0/xx for the versions with the 5 V regulator; TJA1028T/3V3/xx and TJA1028TK/3V3/xx for the versions with the 3.3 V regulator. [2] TJA1028T/xxx/20 and TJA1028TK/xxx/20 for the normal slope versions that support baud rates up to 20 kBd; TJA1028T/xxx/10 and TJA1028TK/xxx/10 for the low slope versions that support baud rates up to 10.4 kBd (SAE J2602). 4. Marking Table 2. TJA1028 Product data sheet Marking codes Type number Marking TJA1028T/5V0/10 1028/51 TJA1028T/5V0/20 1028/52 TJA1028T/3V3/10 1028/31 TJA1028T/3V3/20 1028/32 TJA1028TK/5V0/10 28/51 TJA1028TK/5V0/20 28/52 TJA1028TK/3V3/10 28/31 TJA1028TK/3V3/20 28/32 All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 © NXP B.V. 2012. All rights reserved. 2 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator 5. Block diagram VBAT VBAT UV DET VOLTAGE REFERENCE VCC VCC UV DET VREG OVERTEMP DETECTION EN VCC CONTROL RSTN VBAT Rx LIN Tx LIN GND TJA1028 Product data sheet TXD TIMEOUT TIMER VCC TXD TJA1028 Fig 1. RXD 015aaa085 Block diagram All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 © NXP B.V. 2012. All rights reserved. 3 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator 6. Pinning information 6.1 Pinning terminal 1 index area VBAT 1 8 VCC EN 2 7 RSTN GND 3 6 TXD LIN 4 5 RXD VBAT 1 EN 2 VCC 7 RSTN TJA1028TK TJA1028T GND 3 6 TXD LIN 4 5 RXD 015aaa244 Transparent top view 015aaa082 a. TJA1028T/xxx/xx: SO8 Fig 2. 8 b. TJA1028TK/xxx/xx: HVSON8 Pin configuration diagrams 6.2 Pin description Table 3. Pin description Symbol Pin Description VBAT 1 battery supply for the TJA1028 EN 2 enable input GND 3[1] ground LIN 4 LIN bus line RXD 5 LIN receive data output TXD 6 LIN transmit data input RSTN 7 reset output (active LOW) VCC 8 voltage regulator output [1] For enhanced thermal and electrical performance, the exposed center pad of the HVSON8 package should be soldered to board ground (and not to any other voltage level). 7. Functional description The TJA1028 combines the functionality of a LIN transceiver and a voltage regulator in a single chip and offers wake-up by bus activity. The voltage regulator is designed to power the Electronic Control Unit’s (ECU) microcontroller and its peripherals. The LIN transceiver is the interface between a LIN master/slave protocol controller and the physical bus in a LIN network. According to the Open System Interconnect (OSI) model, these modules make up the LIN physical layer. TJA1028 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 © NXP B.V. 2012. All rights reserved. 4 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator The TJA1028T/xxx/20 and TJA1028TK/xxx/20 versions are optimized for a transmission speed of 20 kBd, the maximum specified in the LIN standard. The TJA1028T/xxx/10 and TJA1028TK/xxx/10 versions are optimized for a transmission speed of 10.4 kBd, as specified in SAE J2602. All versions achieve optimum ElectroMagnetic Compatibility (EMC) performance by wave shaping the LIN output. 7.1 LIN 2.x/SAE J2602 compliant The TJA1028 is fully LIN 2.0, LIN 2.1, LIN 2.2 and SAE J2602 compliant. Since the LIN physical layer is independent of higher OSI model layers (e.g. the LIN protocol), nodes containing a LIN 2.2-compliant physical layer can be combined, without restriction, with LIN physical layer nodes that comply with earlier revisions (i.e. LIN 1.0, LIN 1.1, LIN 1.2, LIN 1.3, LIN 2.0 and LIN 2.1). 7.2 Operating modes The TJA1028 supports four operating modes: Normal, Standby, Sleep and Off. The operating modes, and the transitions between modes, are illustrated in Figure 3. AII states VBAT < Vth(det)poff OR Tvj > Tth(act)otp remote wake-up OFF LIN = off RXD = floating RSTN = LOW VBAT > Vth(det)pon AND Tvj < Tth(rel)otp EN = 1 AND RSTN = 1 STANDBY LIN = off (RXD signals wake source) EN = 1 0 AND TXD = 1 AND RSTN = 1 NORMAL(1) LIN = on EN = 1 0 AND(3) EN = 1 TXD = 0 AND RSTN = 1 wake-up(3) event SLEEP LIN = off RXD = VCC(2) RSTN = LOW Voltage regulator - on Voltage regulator - off 015aaa086 (1) In Normal mode, the LIN transmitter is enabled - but if EN and/or RSTN go LOW, the LIN transmitter will be disabled. Remote wake-up signalling will be activated. (2) Until VCC drops below 2 V. (3) If a wake-up event and a go-to-sleep event occur simultaneously, the device will switch directly to Standby mode without initiating a reset. Fig 3. TJA1028 Product data sheet State diagram All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 © NXP B.V. 2012. All rights reserved. 5 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator 7.2.1 Off mode The TJA1028 switches to Off mode from all other modes if the battery supply voltage drops below the power-off detection threshold (Vth(det)poff) or the junction temperature exceeds the overtemperature protection activation threshold (Tth(act)otp). The voltage regulator and the LIN physical layer are disabled in Off mode, and pin RSTN is forced LOW. 7.2.2 Standby mode Standby mode is a low-power mode that guarantees very low current consumption. The TJA1028 switches from Off mode to Standby mode as soon as the battery supply voltage rises above the power-on detection threshold (VBAT > Vth(det)pon), provided the junction temperature is below the overtemperature protection release threshold (Tvj < Tth(rel)otp). The TJA1028 switches to Standby mode from Normal mode during the mode select window if TXD is HIGH and EN is LOW (see Section 7.2.5), provided RSTN = 1. A remote wake-up event will trigger a transition to Standby mode from Sleep mode. The remote wake-up event will be signalled by a continuous LOW level on pin RXD. In Standby mode, the voltage regulator is on, the LIN physical layer is disabled and remote wake-up detection is active. The wake-up source is indicated by the level on RXD (LOW indicates a remote wake-up). 7.2.3 Normal mode If the EN pin is pulled HIGH while the TJA1028 is in Standby mode (with RSTN = 1) or Sleep mode, the device will enter Normal mode. The LIN physical layer and the voltage regulator are enabled in Normal mode. 7.2.3.1 The LIN transceiver in Normal mode The LIN transceiver is activated when the TJA1028 enters Normal mode. In Normal mode, the transceiver can transmit and receive data via the LIN bus. The receiver detects data streams on the LIN pin and transfers them to the microcontroller via pin RXD. LIN recessive is represented by a HIGH level on RXD, LIN dominant by a LOW level. The transmit data streams of the protocol controller at the TXD input are converted by the transmitter into bus signals with optimized slew rate and wave shaping to minimize EME. A LOW level at the TXD input is converted to a LIN dominant level while a HIGH level is converted to a LIN recessive level. 7.2.4 Sleep mode Sleep mode features extremely low power consumption. The TJA1028 switches to Sleep mode from Normal mode during the mode select window if TXD and EN are both LOW (see Section 7.2.5), provided RSTN = 1. The voltage regulator and the LIN physical layer are disabled in Sleep mode. Pin RSTN is forced LOW. Remote wake-up detection is active. TJA1028 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 © NXP B.V. 2012. All rights reserved. 6 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator 7.2.5 Transition from Normal to Sleep or Standby mode When EN is driven LOW in Normal mode, the TJA1028 disables the transmit path. The mode select window opens tmsel(min) after EN goes LOW, and remains open until tmsel(max) after EN goes LOW (see Figure 4). The TXD pin is sampled in the mode select window. A transition to Standby mode is triggered if TXD is HIGH, or to Sleep mode if TXD is LOW. To avoid complicated timing in the application, EN and TXD can be pulled LOW at the same time without having any effect on the LIN bus. In order to ensure that the remote wake-up time (twake(dom)LIN) is not reset on a transition to Sleep mode, TXD should be pulled LOW at least td(EN-TXD) after EN goes LOW. This is guaranteed by design. The user must ensure the appropriate level is present on pin TXD while the mode select window is open. EN TXD operating mode mode select window Normal Normal with TXD path blocked Sleep or Standby depending on TXD level in mode select window tmsel(min) tmsel(max) 015aaa087 TXD is sampled during the mode select window. The TJA1028 switches to Standby (TXD HIGH) or Sleep (TXD LOW) mode after sampling. Fig 4. Transition from Normal to Sleep/Standby mode 7.3 Power supplies 7.3.1 Battery (pin VBAT) The TJA1028 contains a single supply pin, VBAT. An external diode is needed in series to protect the device against negative voltages. The operating range is from 4.5 V to 28 V. The TJA1028 can handle voltages up to 40 V (max). If the voltage on pin VBAT falls below Vth(det)poff, the TJA1028 switches to Off mode, shutting down the internal logic and the voltage regulator and disabling the LIN transmitter. The TJA1028 exits Off mode as soon as the voltage rises above Vth(det)pon, provided the junction temperature is below Tth(rel)otp. 7.3.2 Voltage regulator (pin VCC) The TJA1028 contains a voltage regulator supplied via pin VBAT, which delivers up to 70 mA. It is designed to supply the microcontroller and its periphery via pin VCC. TJA1028 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 © NXP B.V. 2012. All rights reserved. 7 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator 7.3.3 Reset (pin RSTN) The output voltage on pin VCC is monitored continuously and a system reset signal is generated (pin RSTN goes LOW) if an undervoltage event is detected (VCC < Vuvd for tdet(uv)(VCC)). Pin RSTN will go HIGH again once the voltage on VCC exceeds the undervoltage recovery threshold (Vuvr) for trst. 7.4 LIN transceiver The transceiver is the interface between a LIN master/slave protocol controller and the physical bus in a LIN network. It is primarily intended for in-vehicle sub-networks using baud rates from 2.4 kBd up to 20 kBd and is LIN 2.0/LIN 2.1/SAE J2602 compliant. 7.5 Remote wake-up A remote wake-up is triggered by a falling edge on pin LIN, followed by LIN remaining LOW for at least twake(dom)LIN, followed by a rising edge on pin LIN (see Figure 5). LIN recessive VBAT VBUSrec VLIN VBUSdom twake(dom)LIN LIN dominant ground Standby/Sleep mode RXD Sleep: floating/Standby: HIGH Standby mode LOW 015aaa088 Fig 5. Remote wake-up behavior The remote wake-up request is communicated to the microcontroller in Standby mode by a continuous LOW level on pin RXD. Note that twake(dom)LIN is measured in Sleep and Standby modes, and in Normal mode if TXD is HIGH. 7.6 Fail-safe features 7.6.1 General fail-safe features The following general fail-safe features have been implemented: • An internal pull-up towards VCC on pin TXD guarantees a recessive bus level if the pin is left floating by a bad solder joint or floating microcontroller port pin. • The current in the transmitter output stage is limited in order to protect the transmitter against short circuits to pin VBAT. • A loss of power (pins VBAT and GND) has no impact on the bus line or on the microcontroller. There will be no reverse currents from the bus. • The LIN transmitter is automatically disabled when either EN or RSTN is LOW. TJA1028 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 © NXP B.V. 2012. All rights reserved. 8 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator • After a transition to Normal mode, the LIN transmitter is only enabled if a recessive level is present on pin TXD. 7.6.2 TXD dominant time-out function A TXD dominant time-out timer circuit prevents the bus line being driven to a permanent dominant state (blocking all network communications) if TXD is forced permanently LOW by a hardware or software application failure. The timer is triggered by a negative edge on the TXD pin. If the pin remains LOW for longer than the TXD dominant time-out time (tto(dom)TXD), the transmitter is disabled, driving the bus line to a recessive state. The timer is reset by a positive edge on TXD. 7.6.3 Temperature protection The temperature of the IC is monitored in Normal, Standby and Off modes. If the temperature is too high (Tvj > Tth(act)otp), the TJA1028 will switch to Off mode (if in Standby or Normal modes). The voltage regulator and the LIN transmitter will be switched off and the RSTN pin driven LOW. When the temperature falls below the overtemperature protection release threshold (Tvj < Tth(rel)otp), the TJA1028 switches to Standby mode. 8. Limiting values Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Conditions Min Max Unit VBAT battery supply voltage DC; continuous 0.3 +40 V Vx voltage on pin x DC value pin VCC 0.3 +7 V pins TXD, RXD, RSTN and EN 0.3 VCC + 0.3 V 40 +40 V 8 +8 kV 2 +2 kV 8 +8 kV 250 +250 V 750 +750 V pin LIN with respect to GND VESD electrostatic discharge voltage [1] HBM at pins LIN and VBAT [2] at any other pin IEC 61000-4-2 [3] at pins LIN and VBAT [4] MM at any pin [5] CDM at corner pins 500 +500 V [6] 150 +100 V [7] 40 +150 C 55 +150 C at any other pin transient voltage Vtrt on pin VBAT via reverse polarity diode/capacitor; on pin LIN via 1 nF coupling capacitor Tvj virtual junction temperature Tstg storage temperature [1] Human Body Model (HBM): according to AEC-Q100-002 (100 pF, 1.5 k). [2] VCC and VBAT connected to GND, emulating application circuit. TJA1028 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 © NXP B.V. 2012. All rights reserved. 9 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator [3] ESD performance of pins LIN and VBAT according to IEC 61000-4-2 (150 pF, 330 ) has been verified by an external test house. [4] Machine Model (MM): according to AEC-Q100-003 (200 pF, 0.75 H, 10 ). [5] Charged Device Model (CDM): according to AEC-Q100-011 (field induced charge; 4 pF). [6] Verified by an external test house to ensure pins can withstand ISO 7637 part 2 automotive transient test pulses 1, 2a, 3a and 3b. [7] Junction temperature in accordance with IEC 60747-1. An alternative definition is: Tj = Tamb + P Rth(j-a), where Rth(j-a) is a fixed value. The rating for Tvj limits the allowable combinations of power dissipation (P) and ambient temperature (Tamb). 9. Thermal characteristics Table 5. Symbol Rth(j-a) Thermal characteristics Parameter Conditions thermal resistance from junction to ambient Typ Unit SO8; single-layer board [1] 132 K/W SO8; four-layer board [2] 93 K/W HVSON8; single-layer board [1] 129 K/W HVSON8; four-layer board [3] 67 K/W [1] According to JEDEC JESD51-2 and JESD51-3 at natural convection on 1s board. [2] According to JEDEC JESD51-2, JESD51-5 and JESD51-7 at natural convection on 2s2p board. Board with two inner copper layers (thickness: 35 m) and thermal via array under the package connected to the first inner copper layer. [3] According to JEDEC JESD51-2, JESD51-5 and JESD51-7 at natural convection on 2s2p board. Board with two inner copper layers (thickness: 35 m) and thermal via array under the exposed pad connected to the first inner copper layer. 10. Static characteristics Table 6. Static characteristics VBAT = 5.5 V to 28 V; Tvj = 40 C to +150 C; RL(LIN-VBAT) = 500 ; all voltages are defined with respect to ground; positive currents flow into the IC; typical values are given at VBAT = 12 V; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Standby mode; VLIN = VBAT - 45 59 A Sleep mode; VLIN = VBAT - 12 18 A Normal mode; bus recessive; VLIN = VBAT; VRXD = VCC; VRSTN = HIGH - 850 1800 A Normal mode; bus dominant; VBAT = 12 V; VTXD = 0 V; VRSTN = HIGH - 2.0 4.5 mA Supply; pin VBAT IBAT battery supply current Vth(det)pon power-on detection threshold voltage - - 5.25 V Vth(det)poff power-off detection threshold voltage 3 - 4.2 V Vhys(det)pon power-on detection hysteresis VBAT = 2 V to 28 V voltage 50 - - mV VCC(nom) = 5 V; IVCC = 70 mA to 0 mA 4.9 5 5.1 V VCC(nom) = 3.3 V; VBAT = 4.5 V to 28 V; 3.234 3.3 3.366 V 250 - 70 mA Supply; pin VCC VCC supply voltage IVCC = 70 mA to 0 mA IOlim output current limit TJA1028 Product data sheet VCC = 0 V to 5.5 V All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 © NXP B.V. 2012. All rights reserved. 10 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator Table 6. Static characteristics …continued VBAT = 5.5 V to 28 V; Tvj = 40 C to +150 C; RL(LIN-VBAT) = 500 ; all voltages are defined with respect to ground; positive currents flow into the IC; typical values are given at VBAT = 12 V; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Vuvd undervoltage detection voltage VCC(nom) = 5 V 4.5 - 4.75 V VCC(nom) = 3.3 V 2.97 - 3.135 V Vuvr undervoltage recovery voltage VCC(nom) = 5 V 4.6 - 4.9 V 3.036 - 3.234 V - - 7 - - 9 1.8 10 - F 0.3 VCC - 0.7 VCC V R(VBAT-VCC) VCC(nom) = 3.3 V resistance between pin VBAT and pin VCC VCC(nom) = 5 V; VBAT = 4.5 V to 5.5 V; IVCC = 70 mA to 5 mA; regulator in saturation [1] [2] Tvj = 85 C Tvj = 150 C Co equivalent series resistance < 5 output capacitance [2] LIN transmit data input; pin TXD Vth(sw) switching threshold voltage VCC = 2.97 V to 5.5 V Vhys(i) input hysteresis voltage VCC = 2.97 V to 5.5 V Rpu pull-up resistance 200 - - mV 5 12 25 k LIN receive data output; pin RXD IOH HIGH-level output current Normal mode; VLIN = VBAT; VRXD = VCC 0.4 V - - 0.4 mA IOL LOW-level output current Normal mode; VLIN = GND; VRXD = 0.4 V 0.4 - - mA Enable input; pin EN Vth(sw) switching threshold voltage 0.8 - 2 V Rpd pull-down resistance 50 130 400 k Reset output; pin RSTN Rpu pull-up resistance VRSTN = VCC 0.4 V; VCC = 2.97 V to 5.5 V 3 - 12 k IOL LOW-level output current VRSTN = 0.4 V; VCC = 2.97 V to 5.5 V; 40 C < Tvj < 195 C 3.2 - 40 mA VOL LOW-level output voltage VCC = 2.5 V to 5.5 V; 40 C < Tvj < 195 C 0 - 0.5 V VOH HIGH-level output voltage 40 C < Tvj < 195 C 0.8 VCC - VCC + 0.3 V LIN bus line; pin LIN IBUS_LIM current limitation for driver dominant state VBAT = VLIN = 18 V; VTXD = 0 V 40 - 100 mA IBUS_PAS_rec receiver recessive input leakage current VLIN = 18 V; VBAT = 5.5 V; VTXD = VCC - - 2 A IBUS_PAS_dom receiver dominant input leakage current including pull-up resistor Normal mode; VTXD = VCC; VLIN = 0 V; VBAT = 12 V 600 - - A IBUS_NO_GND loss-of-ground bus current VBAT = 18 V; VLIN = 0 V 750 - +10 A IBUS_NO_BAT loss-of-battery bus current VBAT = 0 V; VLIN = 18 V - - 2 A TJA1028 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 © NXP B.V. 2012. All rights reserved. 11 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator Table 6. Static characteristics …continued VBAT = 5.5 V to 28 V; Tvj = 40 C to +150 C; RL(LIN-VBAT) = 500 ; all voltages are defined with respect to ground; positive currents flow into the IC; typical values are given at VBAT = 12 V; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit VBUSrec receiver recessive state VBAT = 5.5 V to 18 V 0.6 VBAT - - V VBUSdom receiver dominant state VBAT = 5.5 V to 18 V - - 0.4 VBAT V VBUS_CNT receiver center voltage VBAT = 5.5 V to 18 V; VBUS_CNT = (VBUSdom + VBUSrec) / 2 [3] 0.475 0.5 VBAT VBAT 0.525 VBAT V VHYS receiver hysteresis voltage VBAT = 5.5 V to 18 V; VHYS = VBUSrec VBUSdom [3] 0.05 VBAT 0.15 VBAT 0.175 VBAT V VSerDiode voltage drop at the serial diode in pull-up path with Rslave; ISerDiode = 0.9 mA [2] 0.4 - 1.0 V CLIN capacitance on pin LIN with respect to GND [2] - - 30 pF VO(dom) dominant output voltage Normal mode; VTXD = 0 V; VBAT = 7 V - - 1.4 V Normal mode; VTXD = 0 V; VBAT = 18 V - - 2.0 V between pin LIN and VBAT; VLIN = 0 V; VBAT = 12 V 20 30 60 k Rslave slave resistance Temperature protection Tth(act)otp overtemperature protection activation threshold temperature 165 180 195 C Tth(rel)otp overtemperature protection release threshold temperature 126 138 150 C [1] See Figure 1 and Figure 6. [2] Not tested in production; guaranteed by design. [3] See Figure 8. TJA1028 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 © NXP B.V. 2012. All rights reserved. 12 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator 001aan953 7 R(VBAT-VCC)(typ) (Ω) 6 5 4 3 2 -50 0 50 100 150 Tvj (°C) Fig 6. Graph of R(VBAT-VCC)(typ) as a function of junction temperature (Tvj) 11. Dynamic characteristics Table 7. Dynamic characteristics VBAT = 5.5 V to 18 V; Tvj = 40 C to +150 C; RL(LIN-VBAT) = 500 ; all voltages are defined with respect to ground; positive currents flow into the IC; typical values are given at VBAT = 12 V; unless otherwise specified.[1] Symbol Parameter Conditions Min duty cycle 1 Vth(rec)(max) = 0.744VBAT; Vth(dom)(max) = 0.581VBAT; tbit = 50 s; VBAT = 7 V to 18 V [2][3] Vth(rec)(max) = 0.76VBAT; Vth(dom)(max) = 0.593VBAT; tbit = 50 s; VBAT = 5.5 V to 7.0 V [2][3] Vth(rec)(min) = 0.422VBAT; Vth(dom)(min) = 0.284VBAT: tbit = 50 s; VBAT = 7.6 V to 18 V [2][4] Vth(rec)(min) = 0.41VBAT; Vth(dom)(min) = 0.275VBAT; tbit = 50 s; VBAT = 6.1 V to 7.6 V [2][4] Vth(rec)(max) = 0.778VBAT; Vth(dom)(max) = 0.616VBAT; tbit = 96 s; VBAT = 7 V to 18 V [3][4] Vth(rec)(max) = 0.797VBAT; Vth(dom)(max) = 0.630VBAT; tbit = 96 s; VBAT = 5.5 V to 7 V [3][4] Typ Max Unit Duty cycles 1 2 3 TJA1028 Product data sheet duty cycle 2 duty cycle 3 All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 0.396 - - 0.396 - - - - 0.581 - - 0.581 [4][5] [4][5] [5][6] [5][6] 0.417 - - 0.417 - - [5] [5] © NXP B.V. 2012. All rights reserved. 13 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator Table 7. Dynamic characteristics …continued VBAT = 5.5 V to 18 V; Tvj = 40 C to +150 C; RL(LIN-VBAT) = 500 ; all voltages are defined with respect to ground; positive currents flow into the IC; typical values are given at VBAT = 12 V; unless otherwise specified.[1] Symbol 4 Parameter Conditions duty cycle 4 Vth(rec)(min) = 0.389VBAT Vth(dom)(min) = 0.251VBAT tbit = 96 s VBAT = 7.6 V to 18 V [4][5] Vth(rec)(min) = 0.378VBAT; Vth(dom)(min) = 0.242VBAT; tbit = 96 s; VBAT = 6.1 V to 7.6 V [4][5] Min Typ Max - - 0.590 - - 0.590 Unit [6] [6] Timing characteristics trx_pd receiver propagation delay rising and falling; CRXD = 20 pF - - 6 s trx_sym receiver propagation delay symmetry CRXD = 20 pF 2 - +2 s twake(dom)LIN LIN dominant wake-up time Sleep mode 30 80 150 s VTXD = 0 V tto(dom)TXD TXD dominant time-out time tmsel mode select time td(EN-TXD) delay time from EN to TXD tdet(uv)(VCC) undervoltage detection time on pin VCC [7] CRSTN = 20 pF 6 - 20 ms 3 - 20 s 0 - 1 s 1 - 15 s 2 - 8 ms Reset output; pin RSTN reset time trst [1] All parameters are guaranteed over the virtual junction temperature range by design. Factory testing uses correlated test conditions to cover the specified temperature and power supply voltage ranges. [2] Not applicable to the low slope versions (TJA1028T/xxx/10 and TJA1028TK/xxx/10) of the TJA1028. [3] t bus rec min . Variable tbus(rec)(min) is illustrated in the LIN timing diagram in Figure 8. 1 3 = ------------------------------2 t bit [4] Bus load conditions are: CBUS = 1 nF and RBUS = 1 k; CBUS = 6.8 nF and RBUS = 660 ; CBUS = 10 nF and RBUS = 500 . [5] For VBAT > 18 V, the LIN transmitter might be suppressed. If TXD is HIGH then the LIN transmitter output is recessive. [6] t bus rec max 2 4 = ------------------------------- . Variable tbus(rec)(max) is illustrated in the LIN timing diagram in Figure 8. 2 t bit [7] Not tested in production; guaranteed by design. VBAT RXD RLIN TJA1028 CRXD TXD LIN GND CLIN 015aaa198 Fig 7. TJA1028 Product data sheet Timing test circuit for LIN transceiver All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 © NXP B.V. 2012. All rights reserved. 14 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator tbit tbit tbit VTXD tbus(rec)(min) tbus(dom)(max) Vth(rec)(max) Vth(dom)(max) VBAT LIN bus signal Vth(rec)(min) Vth(dom)(min) tbus(dom)(min) output of receiving node A VRXD output of receiving node B VRXD thresholds of receiving node A thresholds of receiving node B tbus(rec)(max) trx_pdf trx_pdr trx_pdr trx_pdf 015aaa199 Fig 8. LIN transceiver timing diagram 12. Test information 12.1 Quality information This product has been qualified in accordance with the Automotive Electronics Council (AEC) standard Q100 - Failure mechanism based stress test qualification for integrated circuits, and is suitable for use in automotive applications. TJA1028 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 © NXP B.V. 2012. All rights reserved. 15 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator 13. Package outline SO8: plastic small outline package; 8 leads; body width 3.9 mm SOT96-1 D E A X c y HE v M A Z 5 8 Q A2 A (A 3) A1 pin 1 index θ Lp 1 L 4 e detail X w M bp 0 2.5 5 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z (1) mm 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 5.0 4.8 4.0 3.8 1.27 6.2 5.8 1.05 1.0 0.4 0.7 0.6 0.25 0.25 0.1 0.7 0.3 inches 0.069 0.010 0.057 0.004 0.049 0.01 0.019 0.0100 0.014 0.0075 0.20 0.19 0.16 0.15 0.05 0.01 0.01 0.004 0.028 0.012 0.244 0.039 0.028 0.041 0.228 0.016 0.024 θ 8o o 0 Notes 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. Fig 9. REFERENCES OUTLINE VERSION IEC JEDEC SOT96-1 076E03 MS-012 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-18 Package outline SOT96-1 (SO8) TJA1028 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 © NXP B.V. 2012. All rights reserved. 16 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator HVSON8: plastic thermal enhanced very thin small outline package; no leads; 8 terminals; body 3 x 3 x 0.85 mm SOT782-1 X B D A E A A1 c detail X terminal 1 index area e1 terminal 1 index area e 1 4 C C A B C v w b y y1 C L K Eh 8 5 Dh 0 1 scale Dimensions Unit(1) mm 2 mm A A1 b max 1.00 0.05 0.35 nom 0.85 0.03 0.30 min 0.80 0.00 0.25 c 0.2 D Dh E Eh e e1 K L 3.10 2.45 3.10 1.65 0.35 0.45 3.00 2.40 3.00 1.60 0.65 1.95 0.30 0.40 2.90 2.35 2.90 1.55 0.25 0.35 v 0.1 w y 0.05 0.05 y1 0.1 Note 1. Plastic or metal protrusions of 0.075 maximum per side are not included. References Outline version IEC JEDEC JEITA SOT782-1 --- MO-229 --- sot782-1_po European projection Issue date 09-08-25 09-08-28 Fig 10. Package outline SOT782-1 (HVSON8) TJA1028 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 © NXP B.V. 2012. All rights reserved. 17 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator 14. Handling information All input and output pins are protected against ElectroStatic Discharge (ESD) under normal handling. When handling ensure that the appropriate precautions are taken as described in JESD625-A or equivalent standards. 15. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 “Surface mount reflow soldering description”. 15.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 15.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: • Through-hole components • Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: • • • • • • Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 15.3 Wave soldering Key characteristics in wave soldering are: TJA1028 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 © NXP B.V. 2012. All rights reserved. 18 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator • Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave • Solder bath specifications, including temperature and impurities 15.4 Reflow soldering Key characteristics in reflow soldering are: • Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 11) than a SnPb process, thus reducing the process window • Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board • Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 8 and 9 Table 8. SnPb eutectic process (from J-STD-020C) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 < 2.5 235 220 2.5 220 220 Table 9. Lead-free process (from J-STD-020C) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 11. TJA1028 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 © NXP B.V. 2012. All rights reserved. 19 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator maximum peak temperature = MSL limit, damage level temperature minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 11. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 “Surface mount reflow soldering description”. 16. Soldering of HVSON packages Section 15 contains a brief introduction to the techniques most commonly used to solder Surface Mounted Devices (SMD). A more detailed discussion on soldering HVSON leadless package ICs can found in the following application notes: • AN10365 ‘Surface mount reflow soldering description” • AN10366 “HVQFN application information” TJA1028 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 © NXP B.V. 2012. All rights reserved. 20 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator 17. Revision history Table 10. Revision history Document ID Release date Data sheet status Change notice Supersedes TJA1028 v.4 20120725 Product data sheet - TJA1028 v.3 Modifications: • • • • • • Table 5: text of table note section amended Table 3: text of table note amended Section 2, Section 7, Section 7.3.2: text revised Section 7.1, Section 7.3.3: added Figure 1, Figure 5: amended Table 6: parameters values/conditions changed: Vth(det)pon, Vth(det)poff TJA1028 v.3 20110519 Product data sheet - TJA1028 v.2 TJA1028 v.2 20100225 Product data sheet - TJA1028 v.1 TJA1028 v.1 20100921 Product data sheet - - TJA1028 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 © NXP B.V. 2012. All rights reserved. 21 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator 18. Legal information 18.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 18.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 18.3 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. TJA1028 Product data sheet Suitability for use in automotive applications — This NXP Semiconductors product has been qualified for use in automotive applications. Unless otherwise agreed in writing, the product is not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 © NXP B.V. 2012. All rights reserved. 22 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. 18.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 19. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] TJA1028 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 25 July 2012 © NXP B.V. 2012. All rights reserved. 23 of 24 TJA1028 NXP Semiconductors LIN transceiver with integrated voltage regulator 20. Contents 1 2 3 4 5 6 6.1 6.2 7 7.1 7.2 7.2.1 7.2.2 7.2.3 7.2.3.1 7.2.4 7.2.5 7.3 7.3.1 7.3.2 7.3.3 7.4 7.5 7.6 7.6.1 7.6.2 7.6.3 8 9 10 11 12 12.1 13 14 15 15.1 15.2 15.3 15.4 16 17 18 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 Functional description . . . . . . . . . . . . . . . . . . . 4 LIN 2.x/SAE J2602 compliant . . . . . . . . . . . . . . 5 Operating modes . . . . . . . . . . . . . . . . . . . . . . . 5 Off mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Standby mode. . . . . . . . . . . . . . . . . . . . . . . . . . 6 Normal mode . . . . . . . . . . . . . . . . . . . . . . . . . . 6 The LIN transceiver in Normal mode . . . . . . . . 6 Sleep mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Transition from Normal to Sleep or Standby mode. . . . . . . . . . . . . . . . . . . . . . . . . . 7 Power supplies . . . . . . . . . . . . . . . . . . . . . . . . . 7 Battery (pin VBAT) . . . . . . . . . . . . . . . . . . . . . . . 7 Voltage regulator (pin VCC) . . . . . . . . . . . . . . . . 7 Reset (pin RSTN) . . . . . . . . . . . . . . . . . . . . . . . 8 LIN transceiver . . . . . . . . . . . . . . . . . . . . . . . . 8 Remote wake-up . . . . . . . . . . . . . . . . . . . . . . . 8 Fail-safe features . . . . . . . . . . . . . . . . . . . . . . . 8 General fail-safe features . . . . . . . . . . . . . . . . . 8 TXD dominant time-out function . . . . . . . . . . . . 9 Temperature protection. . . . . . . . . . . . . . . . . . . 9 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 9 Thermal characteristics . . . . . . . . . . . . . . . . . 10 Static characteristics. . . . . . . . . . . . . . . . . . . . 10 Dynamic characteristics . . . . . . . . . . . . . . . . . 13 Test information . . . . . . . . . . . . . . . . . . . . . . . . 15 Quality information . . . . . . . . . . . . . . . . . . . . . 15 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 16 Handling information. . . . . . . . . . . . . . . . . . . . 18 Soldering of SMD packages . . . . . . . . . . . . . . 18 Introduction to soldering . . . . . . . . . . . . . . . . . 18 Wave and reflow soldering . . . . . . . . . . . . . . . 18 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 18 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 19 Soldering of HVSON packages. . . . . . . . . . . . 20 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 21 Legal information. . . . . . . . . . . . . . . . . . . . . . . 22 18.1 18.2 18.3 18.4 19 20 Data sheet status . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 22 22 23 23 24 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2012. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 25 July 2012 Document identifier: TJA1028