PreliminaryData Sheet NE202930 Silicon NPN Epitaxial High Frequency Transistor R09DS0003EJ0100 Rev.1.00 Jul 14, 2010 FEATURES • • • • High transition frequency fT = 11 GHz TYP. Ideal for low noise and low distortion amplification Suitable for equipments of low collector voltage (Less than 5 V) Suitable for up to 1 GHz applications APPLICATIONS • LNA (Low Noise Amplifier) or power splitter for digital-TV OUTLINE RENESAS Package code: 30 (Package name: 3-pin super minimold (30 PKG)) 1. Emitter 2. Base 3. Collector Note: Marking is "R7D" ORDERING INFORMATION Part Number NE202930-T1 Order Number NE202930-T1-A Package 3-pin super minimold (30 PKG) (Pb-Free) Marking R7D Supplying Form • Embossed tape 8 mm wide • Pin 3 face the perforation side of the tape • Qty 3 kpcs/reel Remark To order evaluation samples, please contact your nearby sales office. Part number for sample order: NE202930 ABSOLUTE MAXIMUM RATINGS (TA = +25°C) Parameter Collector to Base Voltage Collector to Emitter Voltage (Base Short) VCES Ratings 9 9 Collector to Emitter Voltage (Base Open) Emitter to Base Voltage Collector Current Total Power Dissipation Note Junction Temperature Storage Temperature VCEO 6 V VEBO IC Ptot Tj Tstg 2 100 150 150 −65 to +150 V mA mW °C °C Note: Symbol VCBO Unit V V Free air CAUTION Observe precautions when handling because these devices are sensitive to electrostatic discharge. R09DS0003EJ0100 Rev.1.00 Jul 14, 2010 Page 1 of 6 NE202930 ELECTRICAL CHARACTERISTICS (TA = +25°C, unless otherwise specified) Parameter DC Characteristics Collector Cut-off Current Emitter Cut-off Current DC Current Gain RF Characteristics Gain Bandwidth Product Insertion Power Gain Noise Figure (1) Symbol ICBO IEBO hFE Note1 fT ⏐S21e⏐2 NF1 Test Conditions MIN. TYP. MAX. Unit − − 85 − − 140 100 100 205 nA nA − VCE = 5 V, IC = 30 mA, f = 1 GHz VCE = 5 V, IC = 30 mA, f = 1 GHz − 11.5 11.0 13.5 − − GHz dB VCE = 5 V, IC = 5 mA, f = 1 GHz, ZS = ZSopt, ZL = 50 Ω − 1.15 1.5 dB VCB = 5 V, IE = 0 VEB = 1 V, IC = 0 VCE = 5 V, IC = 5 mA Noise Figure (2) NF2 VCE = 5 V, IC = 30 mA, f = 1 GHz, ZS = ZSopt, ZL = ZLopt − 1.5 − dB Associated Gain (1) Ga1 VCE = 5 V, IC = 5 mA, f = 1 GHz, ZS = ZSopt, ZL = 50 Ω 10.0 12.0 − dB Associated Gain (2) Ga2 VCE = 5 V, IC = 30 mA, f = 1 GHz, ZS = ZSopt, ZL = ZLopt VCB = 5 V, IE = 0, f = 1 MHz VCE = 5 V, IC = 30 mA, f = 1 GHz − 13.5 − dB − 13.5 0.6 15.5 0.8 − pF dB Reverse Transfer Capacitance Maximum Stable Power Gain Gain 1 dB Compression Output Power Output 3rd Order Intercept Point Note 2 Cre MSG Note 3 PO (1 dB) VCE = 5 V, IC (set) = 30 mA, f = 1 GHz, ZS = ZSopt, ZL = ZLopt − 19 − dBm OIP3 VCE = 5 V, IC (set) = 30 mA, f = 1 GHz, Δf = 1 MHz, ZS = ZSopt, ZL = ZLopt − 32 − dBm Notes: 1. Pulse measurement: PW ≤ 350 μs, Duty Cycle ≤ 2% 2. Collector to base capacitance when the emitter grounded. S21 3. MSG = S12 hFE CLASSIFICATION Rank Marking hFE Value YFB R7D 85 to 205 R09DS0003EJ0100 Rev.1.00 Jul 14, 2010 Page 2 of 6 NE202930 TYPICAL CHARACTERISTICS (TA = +25°C, unless otherwise specified) TOTAL POWER DISSIPATION vs. AMBIENT TEMPERATURE REVERSE TRANSFER CAPACITANCE vs. COLLECTOR TO BASE VOLTAGE Reverse Transfer Capacitance Cre (pF) Total Power Dissipation Ptot (mW) 200 Free Air 150 100 50 0 25 50 75 100 125 150 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 0 1 2 3 5 4 6 7 8 9 Ambient Temperature TA (°C) Collector to Base Voltage VCB (V) COLLECTOR CURRENT vs. BASE TO EMITTER VOLTAGE COLLECTOR CURRENT vs. COLLECTOR TO EMITTER VOLTAGE 20 100 Collector Current IC (mA) 10 1 0.1 0.01 0.001 0.0001 0 DC Current Gain hFE 1 000 0.2 0.4 0.6 0.8 10 5 1 2 3 100 μA 90 μA 80 μA 70 μA 60 μA 50 μA 40 μA 30 μA 20 μA IB = 10 μA 4 5 Base to Emitter Voltage VBE (V) Collector to Emitter Voltage VCE (V) DC CURRENT GAIN vs. COLLECTOR CURRENT GAIN BANDWIDTH PRODUCT vs. COLLECTOR CURRENT 14 VCE = 5 V 100 10 1 0.001 15 0 0 1.0 Gain Bandwidth Product fT (GHz) Collector Current IC (mA) VCE = 5 V 0.01 0.1 1 10 100 Collector Current IC (mA) 12 VCE = 5 V, f = 1 GHz 10 8 6 4 2 0 1 10 100 Collector Current IC (mA) Remark The graphs indicate nominal characteristics. R09DS0003EJ0100 Rev.1.00 Jul 14, 2010 Page 3 of 6 NE202930 INSERTION POWER GAIN, MAG, MSG vs. COLLECTOR CURRENT 15 |S21e|2 10 5 VCE = 5 V, ICE = 5 mA 0 0.1 1 10 MAG MSG 16 VCE = 5 V, f = 1 GHz 14 12 |S21e|2 10 8 6 4 2 0 1 10 100 Frequency f (GHz) Collector Current IC (mA) NOISE FIGURE, ASSOCIATED GAIN vs. COLLECTOR CURRENT NOISE FIGURE, ASSOCIATED GAIN vs. COLLECTOR CURRENT 15 5 13 4 3 11 2 9 1 7 0 1 Noise Figure NF (dB) 4 VCE = 5 V, f = 1 GHz, ZS = Zopt, ZL = 50 Ω 5 100 10 15 VCE = 5 V, f = 1 GHz, ZS = ZL = Zopt 13 3 11 2 9 1 7 0 1 5 100 10 Collector Current IC (mA) OUTPUT POWER, LINEAR GAIN, COLLECTOR CURRENT vs. INPUT POWER EACH OUTPUT POWER, IM3 vs. EACH INPUT POWER 30 20 200 VCE = 5 V, ICE (set) = 30 mA, f = 1 GHz 150 Pout GL 10 100 0 50 IC –10 –20 –10 0 10 0 20 Input Power Pin (dBm) Each Output Power Pout (each) (dBm) 3rd Order Intermodulation Distortion IM3 (dB) Collector Current IC (mA) Collector Current IC (mA) Noise Figure NF (dB) MAG 18 40 30 20 10 Associated Gain Ga (dB) MSG 20 5 Output Power Pout (dBm) Linear Gain GL (dB) Insertion Power Gain |S21e|2 (dB) Maximum Available Power Gain MAG (dB) Maximum Stable Power Gain MSG (dB) 25 Associated Gain Ga (dB) Insertion Power Gain |S21e|2 (dB) Maximum Available Power Gain MAG (dB) Maximum Stable Power Gain MSG (dB) INSERTION POWER GAIN, MAG, MSG vs. FREQUENCY Pout 0 –10 –20 –30 –40 –50 –60 –70 –80 –30 IM3 –20 –10 0 VCE = 5 V, ICE (set) = 30 mA, f = 1 GHz 10 20 30 Each Input Power Pin (each) (dBm) Remark The graphs indicate nominal characteristics. R09DS0003EJ0100 Rev.1.00 Jul 14, 2010 Page 4 of 6 NE202930 S-PARAMETERS S-parameters and noise parameters are provided on our Web site in a format (S2P) that enables the direct import of the parameters to microwave circuit simulators without the need for keyboard inputs. Click here to download S-parameters. [RF and Microwave] → [Device Parameters] URL http://www2.renesas.com/microwave/en/download.html R09DS0003EJ0100 Rev.1.00 Jul 14, 2010 Page 5 of 6 NE202930 PACKAGE DIMENSIONS 3-PIN SUPER MINIMOLD (30 PKG) (UNIT: mm) 2.1±0.1 2 3 1 0.3+0.1 –0 2.0±0.2 0.65 0.65 0.3+0.1 –0 1.25±0.1 0 to 0.1 0.9±0.1 0.15+0.1 –0.05 0.3 Marking PIN CONNECTIONS 1. Emitter 2. Base 3. Collector R09DS0003EJ0100 Rev.1.00 Jul 14, 2010 Page 6 of 6 Revision History Rev. 1.00 Date Jul 14, 2010 NE202930 Data Sheet Description Summary Page − First edition issued All trademarks and registered trademarks are the property of their respective owners. C-1 Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website. 2. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others. 3. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. 4. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. 5. When exporting the products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. 6. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics 7. Renesas Electronics products are classified according to the following three quality grades: "Standard", "High Quality", and "Specific". The recommended applications for each Renesas Electronics product assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. depends on the product's quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application categorized as "Specific" without the prior written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as "Specific" or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics. The quality grade of each Renesas Electronics product is "Standard" unless otherwise expressly specified in a Renesas Electronics data sheets or data books, etc. "Standard": Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots. "High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; safety equipment; and medical equipment not specifically designed for life support. "Specific": Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life. 8. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. 9. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 10. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 11. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas Electronics. 12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. (Note 1) (Note 2) "Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries. "Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics. http://www.renesas.com SALES OFFICES Refer to "http://www.renesas.com/" for the latest and detailed information. Renesas Electronics America Inc. 2880 Scott Boulevard Santa Clara, CA 95050-2554, U.S.A. Tel: +1-408-588-6000, Fax: +1-408-588-6130 Renesas Electronics Canada Limited 1101 Nicholson Road, Newmarket, Ontario L3Y 9C3, Canada Tel: +1-905-898-5441, Fax: +1-905-898-3220 Renesas Electronics Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K Tel: +44-1628-585-100, Fax: +44-1628-585-900 Renesas Electronics Europe GmbH Arcadiastrasse 10, 40472 Düsseldorf, Germany Tel: +49-211-6503-0, Fax: +49-211-6503-1327 Renesas Electronics (China) Co., Ltd. 7th Floor, Quantum Plaza, No.27 ZhiChunLu Haidian District, Beijing 100083, P.R.China Tel: +86-10-8235-1155, Fax: +86-10-8235-7679 Renesas Electronics (Shanghai) Co., Ltd. Unit 204, 205, AZIA Center, No.1233 Lujiazui Ring Rd., Pudong District, Shanghai 200120, China Tel: +86-21-5877-1818, Fax: +86-21-6887-7858 / -7898 Renesas Electronics Hong Kong Limited Unit 1601-1613, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong Tel: +852-2886-9318, Fax: +852 2886-9022/9044 Renesas Electronics Taiwan Co., Ltd. 7F, No. 363 Fu Shing North Road Taipei, Taiwan, R.O.C. Tel: +886-2-8175-9600, Fax: +886 2-8175-9670 Renesas Electronics Singapore Pte. Ltd. 1 harbourFront Avenue, #06-10, keppel Bay Tower, Singapore 098632 Tel: +65-6213-0200, Fax: +65-6278-8001 Renesas Electronics Malaysia Sdn.Bhd. Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: +60-3-7955-9390, Fax: +60-3-7955-9510 Renesas Electronics Korea Co., Ltd. 11F., Samik Lavied' or Bldg., 720-2 Yeoksam-Dong, Kangnam-Ku, Seoul 135-080, Korea Tel: +82-2-558-3737, Fax: +82-2-558-5141 © 2010 Renesas Electronics Corporation. All rights reserved. Colophon 1.0