HA9P-2625-9 - Rochester Electronics

– N EW P RODUCT I NTRODUCTION –
HA9P-2625-9
Rochester Electronics has re-introduced and continues to manufacture critically needed semiconductors with the full
authorization of the original manufacturer and an attention to quality that meets or exceeds the original component.
Original Manufacturer:
Re-introduced by
Rochester Electronics on
October, 10, 2012
HA9P-2625-9
Original Part Number: HA9P-2625-9
Description: Operational Amplifier
Package: 8 pin SOP
Manufacturing Flow: Industrial
Manufacturing Type:
Rochester re-creation device
HIGH PERFORMANCE OP AMP
useful in a variety of applications
The HA-2620/2625 are bipolar operational amplifiers
that feature very high input impedance coupled with
wideband AC performance. The high resistance of the
input stage is complemented by low offset voltage
and low bias and offset current to facilitate accurate
signal processing. Input offset can be reduced further
by means of an external nulling potentiometer. The
100 MHz gain bandwidth product, 35V/µs slew rate
and 150kV/V open loop gain enables
the HA-2620/2625 to perform high gain
amplification of very fast, wideband signals.
Worldwide Corporate Headquarters
16 Malcolm Hoyt Drive . Newburyport, MA 01950
phone 978.462.9332 . email [email protected] . web www.rocelec.com
© Rochester Electronics, LLC - All Rights Reserved - 11062012
HA-2620, HA-2625
®
Data Sheet
January 16, 2006
100MHz, High Input Impedance, Very
Wideband, Uncompensated Operational
Amplifiers
HA-2620/2625 are bipolar operational amplifiers that feature
very high input impedance (500MΩ, HA-2620) coupled with
wideband AC performance. The high resistance of the input
stage is complemented by low offset voltage (0.5mV,
HA-2620) and low bias and offset current (1nA, HA-2620) to
facilitate accurate signal processing. Input offset can be
reduced further by means of an external nulling
potentiometer. The 100MHz gain bandwidth product
(HA-2620/2625 are stable for closed loop gains greater than
5), 35V/µs slew rate and 150kV/V open loop gain enables
HA-2620/2625 to perform high gain amplification of very fast,
wideband signals. These dynamic characteristics, coupled
with fast settling times, make these amplifiers ideally suited
to pulse amplification designs as well as high frequency
(e.g., video) applications. The frequency response of the
amplifier can be tailored to exact design requirements by
means of an external bandwidth control capacitor connected
from the Comp pin to GND.
In addition to its application in pulse and video amplifier
designs, HA-2620/2625 is particularly suited to other high
performance designs such as high-gain low distortion audio
amplifiers, high-Q and wideband active filters and highspeed comparators. For more information, please refer to
Application Notes AN509, AN519 and AN546.
Ordering Information
PART
NUMBER
PART
MARKING
HA2-2620-2
HA2-2620-2
HA3-2625-5
HA3-2625-5
HA9P2625-9
26259
TEMP.
RANGE
(oC)
PACKAGE
PKG.
DWG. #
Features
• Gain Bandwidth Product (AV ≥ 5). . . . . . . . . . . . . 100MHz
• High Input Impedance . . . . . . . . . . . . . . . . . . . . . 300MΩ
• Low Input Bias Current. . . . . . . . . . . . . . . . . . . . . . . . 5nA
• Low Input Offset Current . . . . . . . . . . . . . . . . . . . . . . 5nA
• Low Input Offset Voltage . . . . . . . . . . . . . . . . . . . . . . 3mV
• High Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150kV/V
• Slew Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35V/µs
• Output Short Circuit Protection
• Compensation Pin for Unity Gain Capability
Applications
• Video and RF Amplifier
• Pulse Amplifier
• Audio Amplifiers and Filters
• High-Q Active Filters
• High Speed Comparators
• Low Distortion Oscillator
Pinouts
HA-2625 (PDIP, SOIC)
TOP VIEW
BAL
1
-IN
2
+IN
V-
-55 to 125 8 Pin Metal Can T8.C
0 to 75
8 Ld PDIP
E8.3
-40 to 85
8 Ld SOIC
M8.15
FN2903.8
8
COMP
7
V+
3
6
OUT
4
5
BAL
+
HA-2620 (METAL CAN)
TOP VIEW
COMP
8
BAL 1
-IN
+
2
+IN
7
V+
6 OUT
5 BAL
3
4
V-
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2003-2006. All Rights Reserved.
All other trademarks mentioned are the property of their respective owners.
HA-2620, HA-2625
Absolute Maximum Ratings
Thermal Information
Supply Voltage (Between V+ and V- Terminals) . . . . . . . . . . . . 45V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12V
Peak Output Current . . . . . . . . . . . . . . . Full Short Circuit Protection
Thermal Resistance (Typical, Note 1)
θJA (oC/W)
θJC (oC/W)
PDIP Package . . . . . . . . . . . . . . . . . . .
117
N/A
SOIC Package . . . . . . . . . . . . . . . . . . .
165
N/A
Metal Can Package . . . . . . . . . . . . . . .
165
80
Maximum Junction Temperature (Hermetic Package) . . . . . . . .175oC
Maximum Junction Temperature (Plastic Package) . . . . . . . .150oC
Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC
(SOIC - Lead Tips Only)
Operating Conditions
Temperature Range
HA-2620-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC
HA-2625-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 75oC
HA-2625-9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θJA is measured with the component mounted on an evaluation PC board in free air.
VSUPPLY = ±15V, Unless Otherwise Specified
Electrical Specifications
HA-2620
PARAMETER
HA-2625
TEMP. (oC)
MIN
TYP
MAX
MIN
TYP
MAX
UNITS
25
-
0.5
4
-
3
5
mV
Full
-
2
6
-
-
7
mV
Full
-
5
-
-
5
-
µV/oC
25
-
1
15
-
5
25
nA
Full
-
10
35
-
-
40
nA
1
15
-
5
25
nA
INPUT CHARACTERISTICS
Offset Voltage
(Note 3)
Average Offset
Voltage Drift
Bias Current
Offset Current
25
Full
-
5
35
-
-
40
nA
Differential Input
Resistance (Note 2)
25
65
500
-
40
300
-
MΩ
Input Noise Voltage Density
(f = 1kHz)
25
-
11
-
-
11
-
nV/√Hz
Input Noise Current Density
(f = 1kHz)
25
-
0.16
-
-
0.16
-
pA/√Hz
Common Mode Range
Full
±11
±12
-
±11
±12
-
V
25
100
150
-
80
150
-
kV/V
Full
70
-
-
70
-
-
kV/V
Common Mode Rejection Ratio
(Note 6)
Full
80
100
-
74
100
-
dB
Minimum Stable Gain
25
5
-
-
5
-
-
V/V
Gain Bandwidth Product
(Notes 4, 7, 8)
25
-
100
-
-
100
-
MHz
Output Voltage Swing (Note 4)
Full
±10
±12
-
±10
±12
-
V
Output Current (Note 5)
25
±15
±22
-
±10
±18
-
mA
Full Power Bandwidth
(Notes 4, 5, 9, 13)
25
400
600
-
320
600
-
kHz
TRANSFER CHARACTERISTICS
Large Signal Voltage Gain
(Notes 4, 5)
OUTPUT CHARACTERISTICS
2
FN2903.8
HA-2620, HA-2625
VSUPPLY = ±15V, Unless Otherwise Specified (Continued)
Electrical Specifications
HA-2620
TEMP. (oC)
PARAMETER
HA-2625
MIN
TYP
MAX
MIN
TYP
MAX
UNITS
TRANSIENT RESPONSE (Note 8)
Rise Time
(Notes 4, 9, 10)
25
-
17
45
-
17
45
ns
Slew Rate
(Notes 4, 9, 10, 12)
25
±25
±35
-
±20
±35
-
V/µs
POWER SUPPLY CHARACTERISTICS
Supply Current
25
-
3
3.7
-
3
4
mA
Power Supply Rejection Ratio
(Note 11)
Full
80
90
-
74
90
-
dB
NOTES:
2. This parameter value guaranteed by design calculations.
3. Offset may be externally adjusted to zero.
4. RL = 2kΩ.
5. VOUT = ±10V.
6. VCM = ±10V.
7. VOUT < 90mV.
8. 40dB Gain.
9. See Transient Response Test Circuits and Waveforms.
10. AV = 5 (The HA-2620 family is not stable at unity gain without external compensation).
11. ∆VS = ±5V.
12. VOUT = ±5V.
Slew Rate
13. Full Power Bandwidth guaranteed by slew rate measurement: FPBW = ----------------------------- .
2πV PEAK
Test Circuits and Waveforms
±40mV
INPUT
1V
INPUT
-1V
0V
±200mV
90%
OUTPUT
10%
0V
RISE TIME
+5V
90%
OUTPUT
10%
-5V
∆V
∆t
SLEW RATE
= ∆V/∆t
NOTE: Measured on both positive and negative transitions from 0V
to +200mV and 0V to -200mV at output.
TRANSIENT RESPONSE
IN
SLEW RATE
V+
OUT
+
-
100kΩ
1.6kΩ
50pF
400Ω
IN
BAL
OUT
COMP
CC
V-
NOTE: Tested Offset Adjustment is |VOS + 1mV| minimum referred to
output. Typical range is ±10mV with RT = 100kΩ.
SLEW RATE AND TRANSIENT RESPONSE
3
SUGGESTED VOS ADJUSTMENT AND
COMPENSATION HOOK-UP
FN2903.8
HA-2620, HA-2625
Schematic Diagram
COMPENSATION
V+
R1
1K
BAL
R2
4.18K
R3
1.56K
R4
1.56K
R5
600
C2
9pF
BAL
Q60
Q1
Q40
Q2
Q3
Q61
Q39
Q41
Q38
Q4
Q42
Q37
Q6
Q5
Q30
Q7
+INPUT
Q11
Q8
Q29
Q13
Q36
Q28
Q32
Q58
Q35
Q43
Q33
Q57
Q44
Q26
Q59
Q55
Q25
Q54
Q18
Q45
Q24
Q27
Q15
Q53
R17
30
Q52
R11
4.0K
Q19
R19
2.5K
R18
30
Q47
Q46
R7
1.35
Q56
OUT
Q17
Q12
Q16
Q31
Q9
Q10
R6
15
Q22
Q21
RP1
R8
1K
Q23
Q48
Q49
Q50
R9
4.5K
Q20
R10
2.0K
C1
16pF
R12
1.6K
R13
1.6K
R14
1.6K
Q51
R15
800
R16
15
V-
-INPUT
Typical Applications
2.2kΩ
2.2kΩ
+15V
2.2kΩ
+
VIN
3
+
2
7
HA-2625
8
4
6
VOUT
+5.0V, 0V
4.25V
HA-2600
R1
10kΩ
R2
100kΩ
50pF
(NOTE)
50pF (NOTE)
C
0.01µF
1N916
1N916
VREF
+
HA-2625
COMP
f=
-15V
OUTPUT
FIGURE 1. HIGH INPUT IMPEDANCE COMPARATOR
4
1
4 (R1 + R2) C
~OUTPUT
FIGURE 2. FUNCTION GENERATOR
FN2903.8
HA-2620, HA-2625
Typical Applications
(Continued)
5pF
22Ω
2.2kΩ
VIN
HA- 2625
+
VOUT
50pF (NOTE)
BW = 1MHz
GAIN = 40dB
NOTE: A small load capacitance of at least 30pF (including stray capacitance) is recommended to prevent possible high frequency oscillations.
FIGURE 3. VIDEO AMPLIFIER
Typical Performance Curves
VS = ±15V, TA = 25oC, Unless Otherwise Specified
15
EQUIVALENT INPUT NOISE (µV)
100
CURRENT (nA)
10
5
0
OFFSET
-5
BIAS
-10
-25
0
25
50
75
10kΩ SOURCE
RESISTANCE
10
0Ω SOURCE
RESISTANCE
1
THERMAL NOISE OF
10K RESISTOR
-1
100Hz
-15
-50
EQUIVALENT INPUT
NOISE vs BANDWIDTH
100
1kHz
10kHz
100kHz
1MHz
UPPER 3dB FREQUENCY
LOWER 3dB FREQUENCY = 10Hz
TEMPERATURE (oC)
FIGURE 4. INPUT BIAS CURRENT AND OFFSET CURRENT
vs TEMPERATURE
10MHz
FIGURE 5. BROADBAND NOISE CHARACTERISTICS
100
80
GAIN
60
60
40
PHASE
100
20
140
0
180
-20
10Hz 100Hz
1kHz
10kHz 100kHz
1MHz 10MHz 100MHz
FREQUENCY
FIGURE 6. OPEN LOOP FREQUENCY RESPONSE
5
INPUT IMPEDANCE (MΩ)
1000
0
20
PHASE ANGLE (DEGREES)
OPEN LOOP VOLTAGE GAIN (dB)
120
800
600
400
200
0
-55
-35
-15
5
25
45
65
85
105
125
TEMPERATURE (oC)
FIGURE 7. INPUT IMPEDANCE vs TEMPERATURE, 100Hz
FN2903.8
HA-2620, HA-2625
Typical Performance Curves
VS = ±15V, TA = 25oC, Unless Otherwise Specified (Continued)
OPEN LOOP VOLTAGE GAIN (dB)
120
20V
PEAK VOLTAGE SWING (±V)
10V
1V
±20V SUPPLY
±15V SUPPLY
±10V SUPPLY
0.1V
100
0pF
10pF
35pF
50pF
80
60
115pF
40
300pF
1000pF
20
0
-20
10Hz
0.01V
10kHz
100kHz
1MHz
10MHz
100MHz
FREQUENCY
100Hz
1kHz
100kHz
10kHz
FREQUENCY
1MHz
10MHz
NOTE: External Compensation is required for closed loop gain < 5.
If external compensation is used, also connect 100pF capacitor from
output to ground.
FIGURE 8. OUTPUT VOLTAGE SWING vs FREQUENCY
FIGURE 9. OPEN LOOP FREQUENCY RESPONSE FOR
VARIOUS VALUES OF CAPACITORS FROM
COMP. PIN TO GND
20
120
±20V SUPPLY
15
±15V SUPPLY
GAIN (dB)
10
±10V SUPPLY
100
±5V SUPPLY
5
5
10
15
SUPPLY VOLTAGE (±V)
80
-55
20
-35
-15
25
45
65
85
105
125
TEMPERATURE (oC)
FIGURE 10. COMMON MODE VOLTAGE RANGE vs SUPPLY
VOLTAGE
FIGURE 11. OPEN LOOP VOLTAGE GAIN vs TEMPERATURE
1000
INPUT NOISE VOLTAGE (nV/√Hz)
5
10
INPUT NOISE CURRENT
100
10
1.0
0.1
INPUT NOISE VOLTAGE
1
1
10
100
1K
FREQUENCY (Hz)
10K
INPUT NOISE CURRENT (pA/√Hz)
COMMON MODE RANGE (±V)
-55oC TO 125oC
0.01
100K
FIGURE 12. NOISE DENSITY vs FREQUENCY
6
FN2903.8
HA-2620, HA-2625
Die Characteristics
PROCESS:
Bipolar Dielectric Isolation
SUBSTRATE POTENTIAL (POWERED UP):
Unbiased
Metallization Mask Layout
TRANSISTOR COUNT:
140
HA-2620, HA-2625
COMP
V+
BAL
OUT
-IN
+IN
BAL
V-
7
FN2903.8
HA-2620, HA-2625
Metal Can Packages (Can)
T8.C MIL-STD-1835 MACY1-X8 (A1)
REFERENCE PLANE
A
8 LEAD METAL CAN PACKAGE
e1
L
L2
L1
INCHES
SYMBOL
ØD2
0.185
4.19
4.70
-
0.019
0.41
0.48
1
Øb1
0.016
0.021
0.41
0.53
1
N
Øb2
0.016
0.024
0.41
0.61
-
ØD
0.335
0.375
8.51
9.40
-
α
ØD1
0.305
0.335
7.75
8.51
-
ØD2
0.110
0.160
2.79
4.06
-
1
β
Øb
k
C
L
e
BASE AND
SEATING PLANE
Q
BASE METAL
Øb1
NOTES
0.165
k1
Øb1
MAX
0.016
Øe
F
MIN
A
A
2
MILLIMETERS
MAX
Øb
A
ØD ØD1
MIN
LEAD FINISH
Øb2
SECTION A-A
NOTES:
1. (All leads) Øb applies between L1 and L2. Øb1 applies between
L2 and 0.500 from the reference plane. Diameter is uncontrolled
in L1 and beyond 0.500 from the reference plane.
2. Measured from maximum diameter of the product.
3. α is the basic spacing from the centerline of the tab to terminal 1
and β is the basic spacing of each lead or lead position (N -1
places) from α, looking at the bottom of the package.
e1
0.200 BSC
5.08 BSC
0.100 BSC
-
2.54 BSC
-
F
-
0.040
-
1.02
-
k
0.027
0.034
0.69
0.86
-
k1
0.027
0.045
0.69
1.14
2
12.70
19.05
1
1.27
1
L
0.500
0.750
L1
-
0.050
L2
0.250
-
6.35
-
1
Q
0.010
0.045
0.25
1.14
-
α
-
β
45o BSC
45o BSC
45o BSC
45o BSC
N
8
8
3
3
4
Rev. 0 5/18/94
4. N is the maximum number of terminal positions.
5. Dimensioning and tolerancing per ANSI Y14.5M - 1982.
6. Controlling dimension: INCH.
8
FN2903.8
HA-2620, HA-2625
Dual-In-Line Plastic Packages (PDIP)
E8.3 (JEDEC MS-001-BA ISSUE D)
N
8 LEAD DUAL-IN-LINE PLASTIC PACKAGE
E1
INDEX
AREA
1 2 3
INCHES
N/2
-B-
-AD
E
BASE
PLANE
-C-
A2
SEATING
PLANE
A
L
D1
e
B1
D1
A1
eC
B
0.010 (0.25) M
C A B S
MILLIMETERS
SYMBOL
MIN
MAX
MIN
MAX
NOTES
A
-
0.210
-
5.33
4
A1
0.015
-
0.39
-
4
A2
0.115
0.195
2.93
4.95
-
B
0.014
0.022
0.356
0.558
-
C
L
B1
0.045
0.070
1.15
1.77
8, 10
eA
C
0.008
0.014
0.204
C
D
0.355
0.400
9.01
eB
NOTES:
1. Controlling Dimensions: INCH. In case of conflict between
English and Metric dimensions, the inch dimensions control.
0.005
-
0.13
-
5
E
0.300
0.325
7.62
8.25
6
E1
0.240
0.280
6.10
7.11
5
e
0.100 BSC
eA
0.300 BSC
3. Symbols are defined in the “MO Series Symbol List” in Section
2.2 of Publication No. 95.
eB
-
L
0.115
5. D, D1, and E1 dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010 inch
(0.25mm).
6. E and eA are measured with the leads constrained to be perpendicular to datum -C- .
5
D1
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
4. Dimensions A, A1 and L are measured with the package seated
in JEDEC seating plane gauge GS-3.
0.355
10.16
N
8
2.54 BSC
7.62 BSC
0.430
-
0.150
2.93
8
6
10.92
7
3.81
4
9
Rev. 0 12/93
7. eB and eC are measured at the lead tips with the leads unconstrained. eC must be zero or greater.
8. B1 maximum dimensions do not include dambar protrusions.
Dambar protrusions shall not exceed 0.010 inch (0.25mm).
9. N is the maximum number of terminal positions.
10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3,
E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch
(0.76 - 1.14mm).
9
FN2903.8
HA-2620, HA-2625
Small Outline Plastic Packages (SOIC)
M8.15 (JEDEC MS-012-AA ISSUE C)
N
INDEX
AREA
8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE
H
0.25(0.010) M
B M
INCHES
E
SYMBOL
-B1
2
3
L
SEATING PLANE
-A-
A
D
h x 45°
-C-
e
A1
B
0.25(0.010) M
C
0.10(0.004)
C A M
MIN
MAX
MIN
MAX
NOTES
A
0.0532
0.0688
1.35
1.75
-
A1
0.0040
0.0098
0.10
0.25
-
B
0.013
0.020
0.33
0.51
9
C
0.0075
0.0098
0.19
0.25
-
D
0.1890
0.1968
4.80
5.00
3
E
0.1497
0.1574
3.80
4.00
4
e
α
B S
0.050 BSC
1.27 BSC
-
H
0.2284
0.2440
5.80
6.20
-
h
0.0099
0.0196
0.25
0.50
5
L
0.016
0.050
0.40
1.27
6
N
α
NOTES:
MILLIMETERS
8
0°
8
8°
0°
7
8°
1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of
Publication Number 95.
Rev. 1 6/05
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Dimension “D” does not include mold flash, protrusions or gate burrs.
Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006
inch) per side.
4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per
side.
5. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater
above the seating plane, shall not exceed a maximum value of
0.61mm (0.024 inch).
10. Controlling dimension: MILLIMETER. Converted inch dimensions
are not necessarily exact.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
10
FN2903.8