WMCF0605-B - Wall Industries

TECHNICAL DATASHEET
Rev. A
WMCF0605-B
Wall Mount AC/DC Power Supply
100~240 Vac Input
5Vdc Output at 1.2A
FEATURES

Single output

100% Burn-In

Short Circuit Protected

RoHS and WEEE Compliant

Over Voltage Protection (Optional)

CEC Level V and Energy Star Compliant

Also available in UK, AUS, and EU Types
DESCRIPTION
The WMCF0605-B AC/DC wall mount power supply offers 6 watts of output power in a 2.95 x 1.38
x 1.46 inch package. The WMCF0605-B has a 5V single output and an input voltage range of
100~240VAC. This supply is 100% burned-in and is protected against short circuit conditions. The
WMCF0605-B is also RoHS, WEEE, CEC Level V, and Energy Star compliant. This supply is
available in US, Europe, Australia, and United Kingdom types.
(888) 597-WALL
www.wallindustries.com
1 of 6
TECHNICAL DATASHEET
Rev. A
WMCF0605-B
TABLE OF CONTENTS
INTRODUCTION
1.0 INPUT REQUIREMENTS
1.1 Voltage (VAC)
1.2 Frequency
1.3 AC Input Current
2.0 OUTPUT REQUIREMENTS
2.1 Output Power
2.2 Output Regulation
2.2.1 Input Voltage
2.2.2 Input Frequency
2.2.3 Static Load
2.2.4 Output Voltage
2.2.5 Ripple
2.3 Transient Response and Deviation
2.4 Turn On, Hold Up Time
2.5 Efficiency
3.0 PROTECTION
3.1 Input Current
3.2 Over Current Protection
3.3 Short Circuit Protection
4.0 MECHANICAL
4.1 Introduction
4.2 General Requirements
4.3 Power Supply Dimensions
4.4 Input/Output Connection
4.5 Unit Color
5.0 RELIABILITY AND QUALITY CONTROL
5.1 MTBF
5.2 Burn-In
6.0 ENVIRONMENTAL CONDITIONS
6.1 Storage temperature
6.1.1 Ambient Temperature
6.1.2 Relative Humidity
6.2 Operating Temperature
6.2.1 Ambient Temperature
6.2.2 Relative Humidity
7.0 EMI EMISSIONS
8.0 SAFETY
8.1 Dielectric Strength (Hi-Pot Test)
8.2 Isolation Resistance
8.3 Leakage Current
9.0 ENVIRONMENTAL PROTECTION
9.1 RoHS and WEEE
9.2 EPA/CEC and MEPS
10.0 PACKAGING
11.0 MECHANICAL DRAWING
(888) 597-WALL
www.wallindustries.com
Page 2 of 6
TECHNICAL DATASHEET
WMCF0605-B
Rev. A
INTRODUCTION
This documents specifies a single output voltage +5VDC power supply for electronic data processing equipment.
This power supply will provide power to all system components.
1.0 INPUT REQUIREMENTS
1.1 Input Voltage Design Range: 90 ~ 264 VAC.
1.2 Line Frequency Design Range: 47 ~ 63 Hz.
1.3 Input Current: 0.18A max. at any line voltage specified in 2.1 and full output load.
2.0 OUTPUT REQUIREMENTS
2.1 Output Power (Rated Power)
This unit’s total output power from all voltages under steady state conditions will not exceed 6W.
2.2 Output Regulation
Label Information per Safety Agencies according to UL1950 and/or EN60950 Requirements.
2.2.1 Rated Input Voltage Range: 100 ~ 240 VAC.
2.2.2 Rated Line Frequency: 50 ~ 60Hz.
2.2.3 Static Load
TABLE 2.2.3
Output
1
Voltage
+5VDC
Minimum Load Maximum Load Surge Current
0A
1.2A
------
2.2.4 Output Voltage
The output voltage is statically regulated for all combinations of load, line and environment, including
cross regulation as shown:
TABLE 2.2.4
Output
1
Voltage
Range
Tolerance
+5 VDC
+4.75VDC ~ +5.25VDC
±5%
NOTE: Test measurements are made at the output connector on the power supply output cord.
2.2.5 Ripple and Noise
Differential ripple and noise on the power supply output is shown below when measured under a
constant load range of 0.01 ~ 1.2A with an oscilloscope at a bandwidth of 20MHz.
TABLE 2.2.5
Output
1
Voltage
Maximum peak to peak ripple and noise
+5VDC
250mV
NOTE: Test measurements are made at the output connector on the power supply output cord. Aluminum
electrolytic capacitor of 10µF and ceramic capacitor of 0.1µF placed in parallel on the output terminal will
prevent unknown noise pick up.
2.3 Transient Response and Deviation
The load regulation for +5VDC is less than ±10%. This measurement was done by changing the measured
output loading from +20% to +80% of the rated load.
(888) 597-WALL
www.wallindustries.com
Page 3 of 6
TECHNICAL DATASHEET
Rev. A
WMCF0605-B
2.4 Turn On, Hold Up Time
During turn on and turn off, no voltage exceeds its nominal voltage by more than 10% and no output will
change its polarity with respect to its return line. All outputs will reach their steady state values within
2 seconds of the turn on and the hold up time for the output must be at least 10 ms tested at 110VAC/50HZ
input with 80% maximum load on the output.
2.5 Efficiency
The efficiency to meet EPS 2.0 level V and CEC/MEPS test requirements.
3.0 PROTECTION
3.1 Input Current
An input fuse or fusible resistor is provided to protect the power supply and the input wiring. And they are
unchangeable units.
3.2 Over Current Protection (OCP)
Overload conditions will cause both the output current and the output voltages to decrease. Removal of an
output overload condition will permit automatic recovery of the output voltage (Maximum = 200% of the
output current).
3.3 Short Circuit Protection (SCP)
The power supply is protected from damage of an accidental short on the output terminal.
4.0 MECHANICAL
4.1 Introduction
The power supply is provided with the output power connector shown in Table 4.1
FRONT VIEW OF OUTPUT CONNECTOR
Table 4.1 Pin out for DC Connector
PIN
Output Voltage
4.2 General Requirements
The power supply must not exceed an audible noise level of 32dB while operating under any combination
of specified load and input voltages and frequencies. This noise level is measured according to IEC
standards 651 type 1, with the sound level meter pointed directly at the power supply in a free-field
condition, at a distance of 1 meter and by selecting nominal “A” weighing frequency attenuation.
4.3 Power Supply Dimensions
The dimensions of the power supply are 2.95 x 1.38 x 1.46 inches (75 x 35 x 37 mm).
4.4 Input / Output Connection
AC PLUG
US 2PIN
DC OUTPUT
2468 24 AWG x 2.1mm x 9.5mm FORK+KINK 5FT BLACK
4.5 Unit Color: BLACK
(888) 597-WALL
www.wallindustries.com
Page 4 of 6
TECHNICAL DATASHEET
WMCF0605-B
Rev. A
5.0 RELIABILITY AND QUALITY CONTROL
5.1 Reliability
The design and construction of this power supply exhibits a minimum mean time between failure of
300,000 hours full rated load operation at 25°C, According to Telcordia SR-332, Issue 2.
5.2 Burn-in
The power supply will be performed at 100% burn-in and 40°C (±5°C) under 80%-100% of full load on all
power supplies.
6.0 ENVIRONMENTAL CONDITIONS
6.1 Storage
This power supply is capable of withstanding the following environmental conditions for extended periods
of time without sustaining electrical and/or mechanical damage and subsequent operational deficiencies:
6.1.1 Ambient temperature: -25°C ~ +85°C
6.1.2 Relative Humidity: 10% ~ 95%
6.2 Operation
The power supply is capable of operating continuously in any mode without performance deterioration in
the following environmental conditions:
6.2.1 Ambient temperature: 0°C ~ +40°C
6.2.2 Relative Humidity: 10% ~ 95%
7.0 EMI EMISSIONS
The power supply meets the radiated and conducted emission requirements for FCC part 15B class B (DoC)
8.0 SAFETY
The power supply must be certified or meet the following safety standards:
Certified
Meet
UL
CUL or CSA
PSE
BSMI
8.1 Dielectric Strength (Hi-Pot) Test System:
Withstand 3KVAC / 10mA, for 2 sec./ min., primary to secondary.
8.2 Isolation Resistance:
Primary to secondary: 10MΩ at 500VDC.
8.3 Leakage current: ≤ 0.25mA
9.0 ENVIRONMENTAL PROTECTION
9.1 RoHS and WEEE
All the parts and processes from design to production for this product meet the requirements of Restriction
of the use of certain hazardous substances in electrical and electronic equipment RoHS directive
2002/95/EC and also meets the directive 2002/96/EC of Waste electrical and electronic equipment (WEEE).
9.2 EPA /CEC and MEPS
To meet the energy saving trend, this product has been designed to meet the American EPA energy star
program for the EPS regulation or requirement of CEC 400-2006-002, AS/NZS/4665.2.2005 for Australia
and New Zealand.
(888) 597-WALL
www.wallindustries.com
Page 5 of 6
TECHNICAL DATASHEET
Rev. A
WMCF0605-B
10.0 PACKAGING
PE BAG.
11.0 MECHANICAL DRAWING (Below spec. of DC Plug is for your reference only!)
US TYPE
Unit: inches (mm)
Company Information:
Wall Industries, Inc. has created custom and modified units for over 40 years. Our in-house research and development engineers will
provide a solution that exceeds your performance requirements on-time and on budget. Our ISO9001-2008 certification is just one
example of our commitment to producing a high quality, well documented product for our customers.
Our past projects demonstrate our commitment to you, our customer. Wall Industries, Inc. has a reputation for working closely with its
customers to ensure each solution meets or exceeds form, fit and function requirements. We will continue to provide ongoing support for
your project above and beyond the design and production phases. Give us a call today to discuss your future projects.
Contact Wall Industries for further information:
Phone:
Toll Free:
Fax:
E-mail:
Web:
Address:
(888) 597-WALL
(603)778-2300
(888)587-9255
(603)778-9797
[email protected]
www.wallindustries.com
5 Watson Brook Rd.
Exeter, NH 03833
www.wallindustries.com
Page 6 of 6