POWERBOX PMP110-45-1

MEDICAL & MILITARY
PMP110 Series
1 1 0 W AT T S M U LT I P L E O U T P U T A C / D C M E D I C A L
Features
• In compliance with EN61000-3-2, EN61000-3-3
and EN61000-1-1-2.
• Thermal protection.
• Overvoltage protection.
• Overcurrent protection.
• 100% burn-in at full rated load.
Specifications
OPERATING
INPUT
Input Voltage
90-132/180-264Vac
Frequency
47Hz–67Hz
Input Current
3.2A (rms) for 115Vac.
1.8A (rms) for 230Vac.
Leakage current
90µA max. @ 115Vac. 60Hz.
150µA max. @ 230Vac. 50Hz.
Insulation
Input – Output: 4000VAC
Input – Ground: 1500VAC
Output – Ground: 500VAC
Inrush Current
15A @ 115V, 30A @ 230V
OUTPUT
MTBF
550,000 hrs @ 25°C
Efficiency
65-70% minimum.
ENVIRONMENTAL
Operating Temperature
0°C to 70°C
Derating
Derate to 50% at 70°C
Storage Temperature
-40°C to 85°C
Relative Humidity
5%–95% non-condensing
STANDARDS AND APPROVALS
Safety standards
UL2601-1, CSA C22.2, TUV EN60601-1
C-Tick
AS/NZS CISPR11 Group 1, Class A
EMC standards
EN60601-1-2: 2001,EN61000-3-2, -3,
EN61000-4-2, -3, -4, -5, -6, -8, -11
Output Voltage
See table
Output Current
See table
Ripple & Noise
1% peak to peak
EMI standards
EN55011 Class B, FCC Class B, VCCI Class B
Line Regulation
±0.2% maximum at full load.
MEPS compliance
TBC
Load Regulation
See table
MECHANICAL
Transient Response
Max. deviation 4% recovering to 1% within
500µs after 25% load charge
Dimensions
254x127x68.58mm
Overvoltage Protection
Provided on V1 only. Set at 110%–132% of
nominal.
Weight
1.4kgs approx.
Overcurrent Protection
All outputs protected for short circuit conditions
Temperature Coefficient
All outputs ±0.04% per °C.
Holdup Time
Typically 12ms at 110VAC.
PFD Signal
(Optional)
Power fail detection signal. TTL logic low upon
loss of input power.
Your dependable power partner – www.powerbox.com.au
365
MEDICAL & MILITARY
PMP110 Series
1 1 0 W AT T S M U LT I P L E O U T P U T A C / D C M E D I C A L
Selection Table
MAX.
MODEL
NUMBER
OUTPUT #1
VNOM IMIN
IMAX
OUTPUT #2
OUTPUT #3
OUTPUT #4
OUTPUT
TOL VNOM IMIN IMAX IPEAK TOL VNOM IMIN IMAX TOL VNOM IMIN IMAX TOL
(N/A)
POWER
PMP110-23
+5V
0.8A
10A
5%
+12V
0A
5A
9.0A
5%
(N/A)
PMP110-31
+5V
0.8A
10A
5%
+12V
0A
5A
9.0A
5%
-12V
0A
2A
5%
110W
(N/A)
110W
PMP110-32
+5V
0.8A
10A
5%
+15V
0A
4A
7.5A
5%
-15V
0A
2A
5%
PMP110-40
+5V
0.8A
10A
5%
+12V
0A
5A
9.0A
5%
-12V
0A
2A
5%
-5V
0A
2A
5%
110W
PMP110-41
+5V
0.8A
10A
5%
+15V
0A
4A
7.5A
5%
-15V
0A
2A
5%
+24V
0A
2A
5%
110W
PMP110-42
+5V
0.8A
10A
5%
+12V
0A
5A
9.0A
5%
-12V
0A
2A
5%
+12V
0A
2A
5%
110W
PMP110-45
+5V
0.8A
10A
5%
+12V
0A
5A
9.0A
5%
-12V
0A
2A
5%
+24V
0A
2A
5%
110W
PMP110-45-1
+5V
2A
10A
5%
+12V
0A
5A
9.0A
5%
-12V
0A
2A
5%
+24V
1.5A
3A
10%
110W
PMP110-45-2
+5V
0.8A
10A
5%
+24V
0A
3A
5.0A
5%
-12V
0A
2A
5%
+12V
0A
2A
5%
110W
PMP110-46
+5V
0.8A
10A
5% +15V 0A
4A
7.5A
5%
-15V
0A
2A
5%
-5V
0A
2A
NOTES: (1) Peak output current with 10% maximum duty cycle for less than 60 seconds. Total peak power must not exceed 130 watts.
(2) The output 1 of model PMP110-45-1 needs a minimum current of 2A to support the other outputs at their maximum rated loads.
5%
110W
(N/A)
110W
Pin Chart
MODEL/PIN
1
PMP110-23
PMP110-31
PMP130-32
PMP130-40
PMP130-41
PMP130-45
PMP130-45-1
PMP130-45-2
PMP130-46
Technical Illustration
366
2
3
5
6
7
8
N.C.
Output 2
Common
Return
Output 1
N.C. or PFD
Output 1
N.C.
Output 2
Common
Return
Output 1
N.C. or PFD
Output 1
Output 4
Output 2
Common
Return
Output 1
N.C. or PFD
Common
Return
N.C.
Output 1
Common
Return
Output 3
Common
Return
Output 3
4