DC/DC Converters TEN 30WIN Series, 30 Watt Features ◆ Smallest encapsulated 30 W converter ◆ 2” x 1” x 0.4” shielded metal package ◆ Ultra wide 4:1 input voltage range ◆ Single- dual- and triple output models ◆ Very high efficiency up to 91% ◆ Operating temp. range –40°C to +75°C ◆ I/O isolation 1500 VDC ◆ Over temperature and short circuit protection ◆ Remote On/Off ◆ Adjustable output voltage ◆ 3-year product warranty CB Scheme UL 60950-1 The TEN 30WIN series is a family of high performance 30W dc-dc converter modules featuring ultra wide 4:1 input voltage ranges in a compact low profile case with industry-standard footprint. Standard features include remote On/Off, output voltage trimming, over voltage protection, under voltage lockout, over temperature and short circuit protection. Typical applications for these products are battery operated equipment and distributed power architectures in communication and industrial electronics, everywhere where isolated, tightly regulated voltages are required and space is limited on the PCB. Models Order code TEN 30-2407WIN TEN 30-2409WIN TEN 30-2410WIN TEN 30-2411WIN TEN 30-2412WIN TEN 30-2413WIN TEN 30-2421WIN TEN 30-2422WIN TEN 30-2423WIN TEN 30-2433WIN TEN 30-2434WIN TEN 30-2431WIN TEN 30-2432WIN TEN 30-4807WIN TEN 30-4809WIN TEN 30-4810WIN TEN 30-4811WIN TEN 30-4812WIN TEN 30-4813WIN TEN 30-4821WIN TEN 30-4822WIN TEN 30-4823WIN TEN 30-4833WIN TEN 30-4834WIN TEN 30-4831WIN TEN 30-4832WIN Input voltage range 9 – 36 VDC (24 VDC nominal) 18 – 75 VDC (48 VDC nominal) http://www.tracopower.com Output 1 1.5 VDC / 8.5 A 2.5 VDC / 8.0 A 3.3 VDC / 7.5 A 5.1 VDC / 6.0 A 12 VDC / 2.5 A 15 VDC / 2.0 A + 5 VDC / 3.0 A +12 VDC / 1.25 A +15 VDC / 1.0 A 3.3 VDC / 5.0 A 3.3 VDC / 5.0 A 5 VDC / 4.0 A 5 VDC / 4.0 A 1.5 VDC / 8.5 A 2.5 VDC / 8.0 A 3.3 VDC / 7.5 A 5.1 VDC / 6.0 A 12 VDC / 2.5 A 15 VDC / 2.0 A + 5 VDC / 3.0 A +12 VDC / 1.25 A +15 VDC / 1.0 A 3.3 VDC / 5.0 A 3.3 VDC / 5.0 A 5 VDC / 4.0 A 5 VDC / 4.0 A Output 2 Output 3 –5 VDC / 3.0 A –12 VDC / 1.25 A –15 VDC / 1.0 A +12 VDC / 0.416 A +15 VDC / 0.333 A +12 VDC / 0.416 A +15 VDC / 0.333 A –12 VDC / 0.416 A –15 VDC / 0.333 A –12 VDC / 0.416 A –15 VDC / 0.333 A –5 VDC / 3.0 A –12 VDC / 1.25 A –15 VDC / 1.0 A +12 VDC / 0.416 A +15 VDC / 0.333 A +12 VDC / 0.416 A +15 VDC / 0.333 A –12 VDC / 0.416 A –15 VDC / 0.333 A –12 VDC / 0.416 A –15 VDC / 0.333 A Efficiency typ. 80 % 83 % 86 % 88 % 89 % 89 % 88 % 87 % 87 % 86 % 86 % 88 % 88 % 80 % 84 % 86 % 88 % 90 % 91 % 88 % 88 % 88 % 86 % 86 % 88 % 88 % Page 1 of 4 DC/DC Converters TEN 30WIN 30 Watt Input Specifications Input current at no load 12 & 15 VDC / ±12 & ±15 VDC models, 24 (nominal input) other models, 24 ±12 & ±15 V models, 48 other models, 48 V: V: V: V: 30 mA typ. 100 mA typ. 15 mA typ. 55 mA typ. Input current at full load (nominal input) V: V: V: V: V: V: V: V: 700 mA typ. 1050 mA typ. 1250 mA typ. 1500 mA typ. 350 mA typ. 520 mA typ. 630 mA typ. 750 mA typ.) 1.5 VDC model, 24 2.5 VDC model, 24 3.3 VDC model, 24 other models, 24 1.5 VDC model, 48 2.5. VDC model, 48 3.3 VDC model, 48 other models, 48 Start-up voltage / under voltage lockout 24 V models: 9 VDC / 8 VDC (typ.) 48 V models: 18 VDC / 16 VDC (typ.) Surge voltage (100 msec. max.) 24 V models: 50 VDC max. 48 V models: 100 VDC max Conducted noise (input) EN 55022 class A with input capacitor 24 V models: 4.7 µF / 50 V 1812 MLCC 48 V models: 2.2 µF / 100 V 1812 MLCC) Output Specifications Voltage set accuracy ±1 % (±5 % for auxilary outputs) Output voltage adjustment (only for single output models) ±10 % with external resistor (see page 3) Regulation – Input variation single- and dual output models: triple output models: – Load variation single output models: dual output models balanced load: dual output models unbalanced load: triple output models (main/auxiliary): 0.2 % max. 1 % / 5 % max. (main / auxilary) 0.5 % max. (0 – 100 %) 1 % max. (0 – 100 %) 5 % max. (25 / 100 %) 1 % max. / 5 % max. (10 – 100 %) single- and dual output models: not required Minimum load triple output models: 10% of rated max current on each output (operation at lower load condition will not damage the converters. However, they may not meet all listed specifications) Temperature coefficient ±0.02 %/K max. Ripple and noise (20 MHz Bandwidth) 1.5 V – 5.1 VDC models: 100 mVpk-pk. typ. triple output models: 50 / 75 mVpk-pk typ. (main / auxilary) other models: 150 mVpk-pk typ. Start up time (nominal Vin and constant resistive load) 30 ms typ. Transient response time (25% load change) 250 µs typ. Short circuit protection indefinite (automatic recovery) Over load protection 150 % of Iout max. typ. Thermal shutdown at +115°C typ. Over voltage protection 1.5 2.5 3.3 5.1 12 15 VDC VDC VDC VDC VDC VDC models: models: models: models: models: models: Capacitive load output models 1.5 – 3.3 VDC models: 5.1 VDC models: 12 & 15 VDC models: ±5 VDC models: other dual output models: 3.3 VDC triple output models: 5 VDC triple output models: 2.0 V 3.3 V 3.9 V 6.2 V 15 V 18 V 20’000 µF max. 14’000 µF max. 2’000 µF max. ±3’000 µF max. ±1’300 µF max. 15’000 / ±220 µF max. (main / auxilary) 8’000 / ±220 µF max. (main / auxilary) All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 4 DC/DC Converters TEN 30WIN 30 Watt General Specifications Temperature ranges – Operating –40°C to +75°C – Case temperature +105°C max. – Storage –55°C to +125°C Derating 3.5 %/K above +60°C Humidity (non condensing) 95 % rel. H max. Thermal inpedance – Natural convection12°C/W – Natural convection with heat sink10°C/W Reliability, calculated MTBF (MIL-HDBK-217F, at +70°C, ground benign) single- and dual output models: 1.2 Mio. h triple output models: 1.1 Mio. h Isolation voltage (60 sec.) – Input / Output 1500 VDC Isolation resistance – Input / Output >1000 M Ohm Isolation capacitance – Input / Output 1500 pF max. Remote On/Off – On: 3.0 to 12 VDC or open circuit. – Off: 0 to 1.2 VDC or short circuit pin 3 and pin 2 – Off idle current: 3 mA max. Switching frequency (pulse width modulation PWM) single- and dual output models: 430 kHz typ. triple output models: 400 kHz typ. Thermal shock, mechanical shock & vibration EN 61373, MIL-STD-810F – Test conditions www.tracopower.com/products/mil810.pdf Safety standards UL 60950-1, IEC/EN 60950-1 Safety approvals – UL/cUL www.ul.com -> certifications -> File e188913 Application note: www.tracopower.com/products/ten30win-application.pdf Output Voltage Adjustment (for single output models only) Trim up Trim down Trim +Vout Rd Ru Trim - Vout Nominal output voltage at open Trim input! Ru [kohm] Rd [kohm] output 1.5 2.5 3.3V5.1V 12V 15V +5% 0.56 4.3 6.8 5.1 43 47 +10% 0.051 0.33 0.75 0.75 4.3 1.8 output 1.5 2.5 3.3V5.1V 12V 15V –5% 0.686.28.26.2 56 56 –10% 0.0620.750.620.82 5.6 2.2 Physical Specifications Casing material copper, nickel plated Baseplate material none conductive FR4 Potting material epoxy (UL 94V-0 -rated) Weight 31 g (1.1oz) Soldering temperature max. 265°C / 10 sec. Environmental compliance http://www.tracopower.com – Reach www.tracopower.com/overview/ten30win – RoHS RoHS Directive 2011/65/EU Page 3 of 4 DC/DC Converters TEN 30WIN 30 Watt Outline Dimensions Single- and dual output models Triple output models 15.24 (0.5) 5.08 5.08 (0.2) (0.2) 2.54 (0.1) 2.5 (0.1) 50.8 (2.0) 45.72 (1.8) 3 2 1 5 5.6 (0.22) 3 2 1 Bottom View 4 7 6 10.16 10.2 (0.4) 20.32 7.62 (0.3) Bottom View 6 Pin-Out 12.7 (0.6) 5 4 Pin Single Dual Triple 1 +Vin (Vcc) +Vin (Vcc) +Vin (Vcc) 2 –Vin (GND) –Vin (GND) –Vin (GND) 3 Remote On/Off Remote On/Off Remote On/Off 4 +Vout 1 Output 1 Output 2 5 –Vout 1 Common Output 3 6 Trim Output 2 Common 7 No pin No pin Output 1 Dimensions in [mm], () = Inch Pin diameter: 1.0 ±0.1 (0.04 ±0.004) Pin pitch tolerances: ±0.25 (±0.01) Case tolerances: ±0.5 (±0.02) 5.08 (0.4) (0.2) 25.4 (0.8) (1.0) 25.4 (1.0) Heat-Sink (Option) Order code: TEN-HS1 (cont.: heat-sink, thermal pad, 2 clamps) Material:Aluminum Finish: Anodic treatment (black) Weight: 17g (0.60oz) without converter Thermal impedance after assembling: 10 K/W 56.0 (2.2) max. Heat-sink Thermal pad Clamp Converter 16.8 (0.66) max. 14.5 (0.57) Note: Before attaching the heatsink, the product label on converter has to be removed for optimal performance. For volume orders we can supply the converters with heatsink already mounted. Please contact us for a relative quotation. Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com www.tracopower.com Rev. September 01 2015 Page 4 of 4