DC/DC Converters TEN 50 Series, 50 Watt g CpBendin Features ◆ Highest power density: Scheme 50 W in 1” x 2” x 0.4” package ◆ Excellent efficiency up to 92 % ◆ Operating temperature range –40°C to +85°C ◆ No minimum load required ◆ Output voltage adjustable ◆ Remote On/Off ◆ I/O isolation 1500 VDC ◆ 3-year product warranty The TEN 50 Series is a range of isolated high ������������������������������������� performance dc-dc converter mod� ules. Due to the very high efficiency of up to 92% and the use of highest reli� able components these 50 W converters come with a footprint of only 1.0” x 2.0”. The 12 models have a wide 2:1 input voltage range and a tight output volt� age regulation. They do not need a minimum load and a offer a high efficiency also at low load conditions. The output voltage is adjustable by external resistor. Remote On/Off and protection against overload and short circuit are standard features of these converters. Typical applications are in mobile equipment, instrumentation, distributed power architectures in communication and industrial electronics and everywhere where space on the PCB is critical. Models Order code Input voltage range TEN 50-1210 Output voltage Output current max. Efficiency 3.3 VDC 10‘000 mA 89 % 5.0 VDC 10’000 mA 90 % 12 VDC 4‘167 mA 91 % 15 VDC 3‘333 mA 91 % TEN 50-1215 24 VDC 2‘080 mA 91 % TEN 50-2410 3.3 VDC 10‘000 mA 89 % 5.0 VDC 10’000 mA 92 % 12 VDC 4‘167 mA 92 % 15 VDC 3‘333 mA 92 % TEN 50-2415 24 VDC 2‘080 mA 91 % TEN 50-4810 3.3 VDC 10‘000 mA 89 % 5.0 VDC 10’000 mA 92 % 12 VDC 4‘167 mA 92 % 15 VDC 3‘333 mA 92 % 24 VDC 2‘080 mA 91 % TEN 50-1211 TEN 50-1212 TEN 50-1213 TEN 50-2411 TEN 50-2412 TEN 50-2413 TEN 50-4811 TEN 50-4812 TEN 50-4813 TEN 50-4815 http://www.tracopower.com 9 – 18 VDC (nominal 12 VDC) 18 – 36 VDC (nominal 24 VDC) 36 – 75 VDC (nominal 48 VDC) Page 1 of 4 DC/DC Converters TEN 50 Series 50 Watt Input Specifications Input current at no load 12 V; 3.3 & 5.0 VDC (nominal input voltage) 12 V; 12 & 15 VDC 12 V; 24 VDC 24 V; 3.3 & 5.0 VDC 24 V; 12 & 15 VDC output 24 V; 24 VDC 48 V; 3.3 & 5.0 VDC 48 V; 12 & 15 VDC 48 V; 24 VDC models: models: models: models: models: models: models: models: models: 85 mA typ. / 110 mA typ. 160 mA typ. 250 mA typ. 50 mA typ. / 70 mA typ. 85 mA typ. 110 mA typ. 35 mA typ. / 45 mA typ. 50 mA typ. 60 mA typ. Surge voltage (100 msec. max.) 12 V models: 25 V max. 24 V models: 50 V max. 48 V models: 100 V max. Reflected input ripple current 12 V models: 50 mA typ. 24 V models: 40 mA typ. 48 V models: 30 mA typ. Conducted noise (input) EN 55022 class A, FCC part 15 level A with external input capacitor (1210 MLCC): 12 V models:22 µF /25 V 24 V models:3.3 µF /50 V 48 V models:2.2 µF /100 V Start-up voltage / under voltage shut down 12 V models: 9.0 VDC max./ 8.3 VDC (or lower) 24 V models: 18 VDC max./ 16.5 VDC (or lower) 48 V models: 36 VDC max./ 33 VDC (or lower) Recommended input fuse (slow blow) 12 V models: 10 A 24 V models: 5 A 48 V models: 2.5 A Output Specifications Voltage set accuracy ±1.0 % Output voltage adjustment range Regulation 24 VDC models: +20 / -10 % other models: ±10 % with external resistor (see page 3) – Input variation Vin min. to Vin max. 0.5 % max. – Load variation 0 – 100 % 0.5 % max. Minimum load not required Temperature coefficient ±0.02 %/K Ripple and noise (20 MHz Bandwidth) 3.3 & 5.0 VDC models: 100 mVpk-pk. typ. (measured with 1 µF MLCC and a 10 µF tantalum capacitor) 12, 15 & 24 VDC models: 150 mVpk-pk typ. Transient response (alignment to 1% at load step change 75% to 100% ) 250 µs typ. Output current limitation at 150% of Iout max. Short circuit protection Capacitive load 24 VDC models: 0.3 Hz. typ. other models: hiccup mode 1.5 Hz, automatic recovery 3.3 5.0 12.0 15.0 24.0 VDC VDC VDC VDC VDC models: models: models: models: models: 25’800 µF max. 17’000 µF max. 2’900 µF max. 1’900 µF max. 750 µF max. All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 4 DC/DC Converters TEN 50 Series 50 Watt General Specifications Temperature ranges – Operating (natural convection cooling 20 LFM) –40°C to +85°C (see load derating) – Case temperature +105°C max. – Storage –50°C to +125°C Load derating – without heatsink – with heatsink Thermal impedance – Natural convection 20 LFM 12°C/W – Natural convection 20 LFM with heatsink 10°C/W 1.1 %/K above 50°C 1.3 %/K above 60°C Humidity (non condensing) 95 % rel H max. Reliability, calculated MTBF (MIL-HDBK-217F, at +25°C, ground benign) >220’000 h Isolation voltage (60 sec.) – Input/Output 1500 VDC Isolation capacitance – Input/Output 2200 pF max. (100 kHz, 1 V) Isolation resistance – Input/Output >1000 Mohm (500 VDC) Switching frequency Remote On/Off 24 VDC models: 285 kHz typ. other models: 320 kHz typ. (pulse width modulation PWM) – On: 3.5 to 12 VDC to -Vin or open circuit. – Off: 0 to +1.2 VDC or short circuit to -Vin – Off idle current: 2.5 mA typ. Safety standards UL/cUL 60950-1 2nd edition, IEC/EN 60950-1 g – CSA certificate (UL/cUL 60950-1 2nd edition) www.tracopower.com/products/ten50-csa.pdf din n – CB test certificate (IEC/EN 60950-1) www.tracopower.com/products/ten50-cb.pdf pe Safety approvals Physical Specifications Casing material alluminium alloy, 6-side shielded, insulating baseplate Potting material epoxy (UL 94V-0 rated) Weight 30 g (1.05 oz) Soldering temperature max. 260°C / 10 sec. (1.5 mm from casing) Environmental compliance – Reach www.tracopower.com/products/ten50-reach.pdf – RoHS directive 2011/65/EU ing Application note: www.tracopower.com/products/ten50-application.pdf nd e p Output Voltage Adjustment Trim up Trim down Trim +Vout Rd Ru Trim - Vout for resistor values see application note All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 3 of 4 DC/DC Converters TEN 50 Series 50 Watt 3 5 6 5.5 (0.22) (0.43) 2.54 (0.1) 11.0 45.72 (1.8) Pin-Out 25.4 (1.0) 2.54 Bottom View (0.8) 4 (0.4) 1 2 20.32 (0.1) (2.0) 10.16 (0.4) (0.2) 10.16 5.08 2.54 50.8 (0.1) Outline Dimensions Heat-sink TEN-HS4 (optional) Pin Single 1 +Vin (Vcc) 2 –Vin (GND) 3 Remote On/Off 4 +Vout 5 –Vout 6 Trim Dimensions in [mm], () = Inch Pin diameter: 1.0 ±0.05 (0.04 ±0.002) Pin pitch tolerance: ±0.13 (±0.005) Case tolerances: ±0.25 (±0.01) Order code: TEN-HS4 (cont.: heat-sink, thermal pad, 2 clamps) Material:Aluminum Finish: Anodic treatment (black) Weight: 17 g (0.60oz) without converter Thermal impedance after assembling: 10 K/W Heat-sink Thermal pad Clamp Converter 31.1 (1.22) 29.0 (1.14) max. 18.0 (0.71) max. Note: Before attaching the heatsink, the product label on converter has to be removed for optimal performance. For volume orders we can supply the converters with heatsink already mounted. Please contact us for a relative quotation. Specifications can be changed any time without notice. Rev. 02/13 Jenatschstrasse 1 · CH-8002 Zurich · Switzerland Tel. +41 43 311 45 11 · Fax +41 43 311 45 45 · [email protected] · www.tracopower.com Page 4 of 4