NEW Series SHP Output to 125A, 480 Vac Phase-Angle Controller Solid-State Relays FEATURES/BENEFITS • Phase angle controller — microcontroller inside • Analog switching • Overvoltage protection by varistor • Green LED for input visualization • IP20 touch-proof flaps • Designed in conformity with EN60947-4-3 (IEC947-4-3) and EN60950/VDE0805 (Reinforced Insulation) SHPXXNXXA relays SHPXXNXXR relays IP20 touchproof flaps Removable input spring connectors Gray: Supply Orange: Analog input 0–10V Part Number Load Voltage Load Current Control Range Also Requires SHP24N50A 90–280Vac 50A 0–10Vdc 8-30Vdc Supply SHP24N50R 90–280Vac 50A 4–20mA SHP48N75A 200–480Vac 75A 0–10Vdc SHP48N75R 200–480Vac 75A 4–20mA SHP48N125A 200–480Vac 125A 0–10Vdc SHP48N125R 200–480Vac 125A 4–20mA 8-30Vdc Supply 8-30Vdc Supply ELECTRICAL SPECIFICATIONS (+25°C ambient temperature unless otherwise specified) ELECTRICAL SPECIFICATIONS (+25°C ambient temperature unless otherwise specified) INPUT (CONTROL) SPECIFICATIONS SHPXXNXXA RELAYS INPUT (CONTROL) SPECIFICATIONS SHPXXNXXR RELAYS Min Max Units 8 30 V Supply Current 12 mA Reverse Supply Voltage 30 V Control Voltage Control Current Range Voltage Range Min Max Units 4 20 mA -0.6 7.5 V 10 V Dynamic Impedance Analog Input Current 100 μA SHP24N50R >100 mΩ Reverse Analog Voltage 30 V SHP48N75R 150 mΩ Analog Input Impedance (Typ.) 120 kΩ SHP48N125R 150 mΩ Analog Voltage Range © 2009 TELEDYNE RELAYS 0 Reverse Polarity Protection Yes Input Current 50 (800) 284-7007 • www.teledynerelays.com mA SHP Page 1 SHP\012009\Q1 NEW Series SHP Output to 125A, 480 Vac Phase-Angle Controller Solid-State Relays MECHANICAL SPECIFICATION TYPICAL APPLICATION Phase 1.77 (45) max Neutral 0.11 (3) Analog input 0-10Vdc M5 1.18 (30) max 2.3 (58.5) max Load Figure 1a — SHPXXNXXA relays 1.10 (28) 1/L1 2/T1 Control – + Supply – + Neutral .20 (5.2) Phase Ø0.185 (4.7) 1.87 (47.6) Supply 8-30Vdc Dimensions in inches (mm) Weight: 2.29 oz. (65g) 1.32 (33.6) 1~ 4– Figure 2a — SHPXXNXXA relays Analog control 4-20mA 1.77 (45) max Ø4.7 1.10 (28) 1/L1 2/T1 4/A2 3/A1 0.20(5.2) 1.70 (43.2) 2.30 (58.5) max M5 1.87 (47.6) 1.18 (30) max 0.28 (7.2) Figure 1b — SHPXXNXXR relays 0.12 (3) 0.64 (16.3) 2~ 3+ Load 1.00 (25.4) M4 Dimensions in inches (mm) Weight: 2.29 oz. (65g) Figure 2b — SHPXXNXXR relays SHP Page 2 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE © 2009 TELEDYNE RELAYS SHP\012009\Q1 NEW Series SHP Output to 125A, 480 Vac Phase-Angle Controller Solid-State Relays ELECTRICAL SPECIFICATIONS (+25°C ambient temperature unless otherwise specified) OUTPUT (LOAD) SPECIFICATIONS OUTPUT (LOAD) SPECIFICATIONS (Continued) Min Max Units SHP24N50A 550 720 A SHP24N50R 550 720 A SHP48N75A 1000 1200 A SHP48N75R 1000 1200 A SHP48N125A 2000 2200 A SHP48N125R 2000 2200 A 0.9 V Non-Repetitive Overload Current Min Max Units SHP24N50A 90 280 Vrms SHP24N50R 90 280 Vrms SHP48N75A 200 480 Vrms SHP48N75R 200 480 Vrms SHP48N125A 200 480 Vrms SHP48N125R 200 480 Vrms SHP24N50A 600 Vpeak SHP24N50R 600 Vpeak SHP48N75A 1200 Vpeak SHP48N75R 1200 Vpeak SHP48N125A 1200 Vpeak SHP48N125R 1200 Vpeak Operating Range Peak Voltage (VDR Clamping) On-State Voltage Drop On-State Dynamic Resistance Latching Voltage SHP24N50A 12 mΩ SHP24N50R 12 mΩ SHP48N75A 4.5 mΩ SHP48N75R 4.5 mΩ SHP48N125A 2 mΩ SHP48N125R 2 mΩ Output Power Dissipation (Max) SHP24N50A 10 V SHP24N50R 10 V SHP48N75A 20 V SHP48N75R 10 V SHP24N50A 2 mA SHP48N125A 20 V SHP24N50R 1 mA SHP48N125R 20 V SHP48N75A 2 mA SHP48N75R 1 mA SHP48N125A 2 mA SHP48N125R 1 mA Load Current Range (See Fig. 5) 0.9x0.9xI + 0.012xI2 W Off-State Leakage Current SHP24N50A 0.1 50 Arms SHP24N50R 0.1 75 Arms SHP48N75A 0.1 125 Arms Init Time (60 Hz) 83.3 ms SHP48N75R 0.1 50 Arms Delay Time (60 Hz) 16.6 ma SHP48N125A 0.1 75 Arms Rise, Fall Time (60 Hz) 52.3 ma SHP48N125R 0.1 125 Arms Operating Frequency 40 70 Hz Off-State dv/dt 500 Maximum di/dt (Non-Repetitive) © 2009 TELEDYNE RELAYS (800) 284-7007 • www.teledynerelays.com V/μs 50 A/μs SHP Page 3 SHP\012009\Q1 NEW Series SHP Output to 125A, 480 Vac Phase-Angle Controller Solid-State Relays OUTPUT (LOAD) SPECIFICATIONS (Continued) Min Max Units GENERAL SPECIFICATIONS (+25°C ambient temperature unless otherwise specified) ENVIRONMENTAL SPECIFICATIONS I2t for fuse matching (<10ms) SHP24N50A 2500 A2s SHP24N50R 2500 A2s SHP48N75A 7200 A 2s SHP48N75R 7200 A 2s SHP48N125A 7200 A 2s SHP48N125R 7200 A 2s Conducted Immunity Level IEC/EN61000-4-4 (bursts) 4kV criterion A IEC/EN61000-4-5 (surge) 4kV criterion A Internal Overvoltage Protection 820(@1mA) Min Max Units Operating Temperature –40 +100 °C Storage Temperature –40 +125 °C Ambient Humidity 40 85 % Input-Output Isolation 4000 Vrms Output-Case Isolation 4000 Vrms Insulation Resistance @500Vdc 1000 MΩ Rated Impulse Voltage 4000 Protection Level (CEI529) IP20 Vibration (10–55 Hz according to CE168) 1.5 mm 30/50 g 0.5 C°/W Shock (according to CE168) V Thermal Resistance (Junction to Case) SHP48NXXR Housing Material V PA6 UL94VO Baseplate Aluminum, nickel-plated TRANSFER CHARACTERISTIC SURGE CURRENT (Vload/Vac) Apeak 600 2 100% 400 75% Non-Repetitive 200 50% Repetitive with initial Tj = 70°C 0 0 0.1 1 10 t(s) 25% Figure 3a — 50A output current 0% Apeak 1500 0 0.3 1000 2.5 5 7.5 9.7 10 Ve(V) Figure 4a — SHPXXNXXA Non-Repetitive 500 (Vload/Vac) 2 Repetitive with initial Tj = 70°C 0 0 0.1 1 10 100% t(s) Figure 3b — 75A output current 75% 2000 Apeak 50% 1500 Non-Repetitive 1000 25% 500 Repetitive with initial Tj = 70°C 0 0% 0 0.1 1 t(s) Figure 3c — 125A output current SHP Page 4 10 0 4 8 12 16 20 Ic(mA) Figure 4b — SHP48NXXR SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE © 2009 TELEDYNE RELAYS SHP\012009\Q1 NEW Series SHP Output to 125A, 480 Vac Phase-Angle Controller Solid-State Relays THERMAL CHARACTERISTICS 100 100 0.75°C/W 0.55°C/W 90 90 0.95°C/W Power Dissipation (W) 80 80 Full on State 70 70 1.1°C/W 60 60 1.5°C/W 50 40 50 40 2.1°C/W 30 30 6°C/W 20 20 50% on State 10 10 0 0 0 5 10 15 20 25 30 35 40 45 50 55 60 0 10 20 30 40 50 60 70 80 90 100 Load Current (Arms) Ambient Temperature (°C) Figure 5a — 50A output power 0.55°C/W 110 0.3°C/W 0.75°C/W 100 90 110 100 90 0.95°C/W Power Dissipation (W) Full on State 80 80 1.1°C/W 70 60 70 60 1.5°C/W 50 50 2.1°C/W 40 40 30 30 20 50% on State 6°C/W 20 10 10 0 0 10 20 30 40 50 60 70 80 90 Load Current (Arms) 0 0 10 20 30 40 50 60 70 80 90 100 Ambient Temperature (°C) Power Dissipation (W) Figure 5b — 75A output power 0.3°C/W 0.2°C/W 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10 0 0 170 160 150 0.55°C/W 140 Full on State 130 120 0.75°C/W 110 0.95°C/W 100 90 80 1.1°C/W 70 60 1.5°C/W 50 2.1°C/W 40 30 50% on State 6°C/W 20 10 0 0 10 20 30 40 50 60 70 80 90 100 15 30 45 60 75 90 105 120 135 150 Load Current (Arms) Ambient Temperature (°C) Figure 5c — 125A output power © 2009 TELEDYNE RELAYS (800) 284-7007 • www.teledynerelays.com SHP Page 5 SHP\012009\Q1 NEW Series SHP Output to 125A, 480 Vac Phase-Angle Controller Solid-State Relays OPTIONAL CONNECTIONS CONTROL WIRING - SHPCCNXXA Connector WAGO 734 Directly with wires, with or without ferrules With tips (ring terminals) Pluggable removable input spring connectors Minimum: AWG28 Maximum: AWG14 With clip CONTROL WIRING - SHPXXNXXR Number of Wires 1 Solid (no ferrule) Screwdriver Type 2 Fine Stranded (with ferrule) Solid (no ferrule) Fine Stranded (with ferrule) Recommended Torque M4 N.m AWG18…AWG14 AWG18…AWG14 AWG18…AWG14 AWG18…AWG14 Pozidriv 2 1.2 Screwdriver Type Recommended Torque POWER WIRING Number of Wires 1 Solid (no ferrule) 2 Fine Stranded (with ferrule) Solid (no ferrule) Fine Stranded (with ferrule) M5 N.m AWG16…AWG8 AWG16…AWG10 AWG16…AWG8 AWG16…AWG10 Power with tips Pozidriv 2 2 Options Fastons: Call us W max = 12.6 mm AWG6 (16mm2) AWG4 (25mm2) AWG2/AWG3 (35mm2) AWG0/AWG1 (50mm2) SHP Page 6 Special kit for high current AWG2 (35mm2) AWG0 (50mm2) SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE © 2009 TELEDYNE RELAYS SHP\012009\Q1 NEW Series SHP Output to 125A, 480 Vac Phase-Angle Controller Solid-State Relays Mounting HIPpak SSRs must be mounted on heat sinks. A large range of heat sinks is available. For heat-sink mounting, use thermal grease or a thermal pad with high conductibility specified by Teledyne. 2–2.5°C/W Teledyne P/N FW151 © 2009 TELEDYNE RELAYS 1.1°C/W Teledyne P/N FW108 Thermal Pad Teledyne P/N –12 (800) 284-7007 • www.teledynerelays.com SHP Page 7 SHP\012009\Q1