MO-9100A

MO-9100A
1-80 MHz High Performance Oscillator
Applications
Features
• Any frequency between 1 and 80 MHz accurate to 6 decimal places
• CMOS compa ble output
• Ultra low phase ji er: 0.5 ps (12 kHz to 20 MHz)
• Industrial and extended commercial temperature ranges
• Standard 4-pin packages: 2.5 x 2.0, 3.2 x 2.5, 5.0 x 3.2, 7.0 x 5.0 mm
• Compu ng, storage, networking, telecom, industrial
control
• SATA, SAS, Ethernet, PCI Express, video, WiFi
Performance SpecificaƟons
Parameter and Condi ons
Output Frequency Range
Frequency Stability
Symbol
f
F_stab
First year Aging
10-year Aging
Opera ng Temperature
Range
F_aging
Supply Voltage
Current Consump on
Min.
1
-10
Typ.
-
Max.
80
+10
Unit
MHz
PPM
T_use
-50
-1.5
-5
-20
-
+50
+1.5
+5
+70
PPM
PPM
PPM
°C
Vdd
-40
1.71
1.8
+85
1.89
°C
V
2.25
2.52
2.97
45
90%
2.5
2.8
3.3
31
29
1.5
3.6
4.6
-
2.75
3.08
3.63
33
31
31
30
70
10
55
2
-
V
V
V
mA
mA
mA
mA
μA
μA
%
ns
ns
ns
Vdd
70%
-
100
6
6
1.5
2
0.6
10%
30%
250
10
150
10
2
3
1
Vdd
Vdd
Vdd
kΩ
ms
ns
ms
ps
ps
ps
Idd
OE Disable Current
I_OD
Standby Current
I_std
Duty Cycle
Rise/Fall Time
DC
Tr, Tf
Output Voltage High
VOH
Output Voltage Low
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
Startup Time
OE Enable/Disable Time
Resume Time
RMS Period Ji er
RMS Phase Ji er (random)
VOL
VIH
VIL
Z_in
T_start
T_oe
T_resume
T_ji
T_phj
Condi on
Inclusive of Ini al tolerance at 25 °C, and varia ons over opera ng
temperature, aging, supply voltage and load
25°C
25°C
Extended Commercial
Industrial
Supply voltages between 2.5V and 3.3V are supported in increments
of 0.1 V. Contact Vectron for guaranteed performance specs for supply
voltages not specified in this table.
No load condi on, f = 20 MHz, Vdd = 2.5V, 2.8V or 3.3V
No load condi on, f = 20 MHz, Vdd = 1.8V
Vdd = 2.5V, 2.8V or 3.3V, OE = GND, output is Weakly Pulled Down
Vdd = 1.8 V. OE = GND, output is Weakly Pulled Down
Vdd = 2.5V, 2.8V or 3.3V, ST = GND, output is Weakly Pulled Down
Vdd = 1.8 V. ST = GND, output is Weakly Pulled Down
15 pF load, 10% -90% Vdd
30 pF load, 10% -90% Vdd
45 pF load, 10% -90% Vdd
OH = -7 mA, IOL = 7 mA, (Vdd = 3.3V, 3.0V) IOH = -4 mA, IOL = 4 mA,
(Vdd = 2.8V, 2.5V) IOH = -2 mA, IOL = 2 mA, (Vdd = 1.8V)
Pin 1, OE or ST
Pin 1, OE or ST
Measured from the me Vdd reaches its rated minimum value
f = 80 MHz, For other frequencies, T_oe = 100 ns + 3 cycles
Measured from the me ST pin crosses 50% threshold
f = 75 MHz, Vdd = 2.5V, 2.8V or 3.3V
f = 75 MHz, Vdd = 1.8V
f = 10 MHz, Integra on bandwidth = 12 kHz to 20 MHz
Page 1 of 5
Vectron Interna onal • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • h p://www.vectron.com
Rev 1.3 Oct 2014
Timing Diagrams
90% Vdd, 2.5/2,8/3.3V devices
Vdd
95% Vdd, 1.8V devices
Vdd
Pin 4 Voltage
ST Voltage
50% Vdd
T_start
T_resume
CLK Output
T_start: Time to start from power-off (ST/OE Mode)
CLK Output
T_resume: Time to resume from standby (ST Mode Only)
Typical Performance
Page 2 of 5
Vectron Interna onal • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • h p://www.vectron.com
Rev 1.3 Oct 2014
Packaging and Pinout
Package Outline & Dimensions (Unit: mm)
Recommended Land PaƩern (Unit: mm)
2.7 x 2.4 x 0.75 mm (100% compatible with 2.5 x 2. 0 mm footprint)
YXXXX
3.2 x 2.5 x 0.75 mm
2.2
3.2 ± 0.05
2.1
#3
0.9
#2
#1
0.9
0.75 ± 0.05
#2
1.2
0.7
YXXXX
#1
#4
1.9
#3
2.5 ± 0.05
#4
1.4
5.0 x 3.2 x 0.75 mm
2.54
5.0 ± 0.05
2.39
#3
#2
2.2
1.6
#2
0.75 ± 0.05
#1
1.1
YXXXX
#4
0.8
#3
3.2 ± 0.05
#4
#1
1.15
1.5
7.0 x 5.0 x 0.90 mm
5.08
2.6
0.90 ± 0.10
2.0
1.1
YXXXX
5.0 ± 0.05
7.0 ± 0.05
3.81
5.08
1.4
2.2
Top View
Pin ConnecƟons
Pin
Symbol
1
OE/ ST
Func onality
Output
Enable
H or Open[*]: specified frequency output L: output is high impedance.
Only output driver is disabled.
Standby
H or Open[*]: specified frequency output L: output is low (weak pull
down). Device goes to sleep mode. Supply current reduces to I_std.
2
GND
Power
Electrical and case ground
3
OUT
Output
Oscillator output
4
VDD
Power
Power supply voltage
OE/ST
1
4
VDD
GND
2
3
OUT
*A pull-up resistor of <10 kΩ between OE/ ST pin and Vdd is recommended in high noise environment
Page 3 of 5
Vectron Interna onal • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • h p://www.vectron.com
Rev 1.3 Oct 2014
Absolute Maximum RaƟngs and Test Compliance
Maximum RaƟngs
Parameter
Min
Max
Unit
Storage Temperature
-65
150
°C
VDD
-0.5
4
V
Electrosta c Discharge
–
2000
V
Soldering Temperature (follow standard Pb free soldering guidelines)
–
260
°C
Number of Program Writes
–
1
NA
Program Reten on over -40 to 125°C, Process, VDD (0 to 3.65V)
1,000+
–
years
Environmental Compliance
Parameter
Condi on/Test Method
Mechanical Shock
MIL-STD-883F, Method 2002
Mechanical Vibra on
MIL-STD-883F, Method 2007
Temperature Cycle
JESD22, Method A104
Solderability
MIL-STD-883F, Method 2003
Moisture Sensi vity Level
MSL1 @ 260°C
Ordering InformaƟon
MO - 9100A E - 4 F - E E - 75M0000000
Product
MO: MEMS XO
Frequency
Feature Pin
E: Enable/Disable
S: Standby
Family
9100A: CMOS clock, 1-80MHz
Temp Range
J: -20/70°C
E: -40/85°C
Package
2: 4 pin 7.0mm x 5.0mm
4: 4 pin 5.0mm x 3.2mm
6: 4 pin 3.2mm x 2.5mm
8: 4 pin 2.5mm x 2.0mm compa ble
Stability
B: ±10ppm
E: ±20ppm
F: ±25ppm
K: ±50ppm
Supply Voltage
E: +3.3 Vdc
G: +2.8 Vdc
H: +2.5 Vdc
J: +1.8 Vdc
Notes:
1. Contact factory for improved stabili es or addi onal product op ons. Not all op ons and codes are available at all
frequencies.
2. Unless otherwise stated all values are valid a er warm-up me and refer to typical condi ons for supply voltage, frequency
control voltage, load, temperature (25°C).
3. Subject to technical modifica on.
4. Contact factory for availability.
Page 4 of 5
Vectron Interna onal • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • h p://www.vectron.com
Rev 1.3 Oct 2014
Revision History
Revision
Change Summary
Date
1.0
Product Release
June 2013
1.1
Knowles logo and address change
Feb 2014
1.2
Add ±20ppm temperature stability
Aug 2014
1.3
Add ±10ppm temperature stability
Oct 2014
For Additional Information, Please Contact
USA:
Europe:
Asia:
Vectron Interna onal
267 Lowell Road, Suite 102
Hudson, NH 03051
Tel: 1.888.328.7661
Fax: 1.888.329.8328
Vectron Interna onal
Landstrasse, D-74924
Neckarbischofsheim, Germany
Tel: +49 (0) 7268.801.100
Fax: +49 (0) 7268.801.282
68 Yin Cheng Road(C), 22nd Floor
One Lu Jia Zui
Pudong, Shanghai 200120, China
Tel: +86 21 6194 6886
Fax: +86 21 6194 6699
Disclaimer
Vectron Interna onal reserves the right to make changes to the product(s) and or informa on contained herein without no ce. No liability is assumed as a result of their use or applicaon. No rights under any patent accompany the sale of any such product(s) or informa on.
Page 5 of 5
Vectron Interna onal • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • h p://www.vectron.com
Rev 1.3 Oct 2014