HT-MM900A Military Temperature Oscillator Applications Features • Frequency Range 1 MHz and 137 MHz accurate to 6 decimal places • Low power consump on of 4.5 mA typical • CMOS compa ble output • Industry-standard packages: 2.0 x 1.6, 2.5 x 2.0, 3.2 x 2.5, 5.0 x 3.2, 7.0 x 5.0 mm • Opera ng temperature to 125°C • Military Applica ons • Environmentally Demanding Applica ons • Ruggedized Equipment • Capable of surviving 50,000 g shock, with 70 g vibra on resistance and 0.1ppb/g g-sensi vity Performance SpecificaƟons Parameter and Condi ons Output Frequency Range Frequency Stability Symbol f F_stab Aging Opera ng Temperature Range Ag T_use Supply Voltage Vdd Min. 1 -20 Typ. – – Max. 137 +20 Unit MHz ppm -50 –1.5 -55 -40 -40 -40 1.62 – – – – – – 1.8 +50 1.5 +125 +125 +105 +85 1.98 ppm ppm °C °C °C °C V 2.5 2.8 3.0 3.3 3.9 3.6 2.5 2.5 1 – 1.2 1.5 1.5 – 2.75 3.08 3.3 3.63 5 4.5 10 10 5 55 2.5 3.5 3 – V V V V mA mA μA μA μA % ns ns ns Vdd Standby Current I_std Duty Cycle Rise/Fall Time DC Tr, Tf Output High Voltage VOH 2.25 2.52 2.7 2.97 – – – – – 45 – – 90% Output Low Voltage VOL – – 10% Vdd Input High Voltage Input Low Voltage Input Pull-up Impedence VIH VIL Z_in 70% – – 2 – – – 100 – – – – – – – 2 2 1.5 2.5 – 30% 250 – 5 150 5 4 4.5 3 3 Vdd Vdd kΩ MΩ ms ns ms ps ps ps ps Current Consump on Startup Time Enable/Disable Time Resume Time RMS Period Ji er RMS Phase Ji er (random) Idd T_start T_oe T_resume T_ji T_phj Condi on Inclusive of Ini al tolerance at 25°C, and varia ons over opera ng temperature, rated power supply voltage and load. 1st year at 25°C Other supply voltages between 2.5V and 3.3V can be supported. Contact Vectron for addi onal informa on. No load condi on, f = 20 MHz, Vdd = 2.5V, 2.8V, 3.0V or 3.3V No load condi on, f = 20 MHz, Vdd = 1.8V ST = GND, Vdd = 3.0V or 3.3V, Output is Weakly Pulled Down ST = GND, Vdd = 2.5V or 2.8V, Output is Weakly Pulled Down ST = GND, Vdd = 1.8V, Output is Weakly Pulled Down All supply voltage op ons 20% - 80% Vdd = 2.5V, 2.8V, 3.0V or 3.3V 20% - 80% Vdd = 1.8V 20% - 80% Vdd = 2.25V - 3.63V IOH = -4 mA (Vdd = 3.0V or 3.3V) IOH = -3 mA (Vdd = 2.8V and Vdd = 2.5V) IOH = -2 mA (Vdd = 1.8V) IOL = 4 mA (Vdd = 3.0V or 3.3V) IOL = 3 mA (Vdd = 2.8V and Vdd = 2.5V) IOL = 2 mA (Vdd = 1.8V) Pin 1, OE or ST Pin 1, OE or ST Pin 1, OE logic high or logic low, or ST logic high Pin 1, ST logic low Measured from the me Vdd reaches its rated minimum value Measured from the me ST pin crosses 50% threshold f = 20 MHz, Vdd = 2.5V, 2.8V, 3.0V or 3.3V f = 20 MHz, Vdd = 1.8V Integra on bandwidth = 12 kHz to 20 MHz, -40 to +125°C Integra on bandwidth = 12 kHz to 20 MHz, -55 to +125°C Page 1 of 6 Vectron Interna onal • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • h p://www.vectron.com Rev 1.3 Aug 2014 Typical Phase Noise 100MHz output, Phase JiƩer <1.2 ps rms, 12kHz - 20MHz Page 2 of 6 Vectron Interna onal • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • h p://www.vectron.com Rev 1.3 Aug 2014 Packaging OpƟons Package Outline & Dimensions (Unit: mm) Recommended Land PaƩern (Unit: mm) [[PP <;;;; 2.5 x 2.0 x 0.75 mm 1.9 2.2 2.5 ± 0.05 #3 1.1 #2 #2 1.0 1.2 #1 #4 0.5 YXXXX 1.00 1.5 1.9 #3 2.0 ± 0.05 #4 #1 0.75 ± 0.05 0.75 1.1 1.4 3.2 x 2.5 x 0.75 mm 2.2 3.2 ± 0.05 2.1 #3 0.7 #2 #1 0.9 0.75 ± 0.05 #2 1.2 #1 0.9 YXXXX #4 1.9 #3 2.5 ± 0.05 #4 1.4 5.0 x 3.2 x 0.75 mm 2.54 5.0 ± 0.05 2.39 #2 0.75 ± 0.05 #1 #4 #2 #1 1.6 2.2 1.1 YXXXX #3 0.8 #3 3.2 ± 0.05 #4 1.5 1.15 7.0 x 5.0 x 0.90 mm 2.0 3.81 1.1 2.6 5.0 ± 0.05 0.90 ± 0.10 YXXXX 5.08 5.08 7.0 ± 0.05 1.4 2.2 Page 3 of 6 Vectron Interna onal • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • h p://www.vectron.com Rev 1.3 Aug 2014 Pin FuncƟonality Top View Pin ConnecƟons Pin Symbol 1 OE/ ST Func onality Output Enable H or Open(1): specified frequency output L: output is high impedance. Only output driver is disabled. Standby H or Open(1): specified frequency output L: output is low (weak pull down). Device goes to sleep mode. Supply current reduces to I_std. 2 GND Power Electrical ground(2) 3 OUT Output Oscillator output 4 VDD Power Power supply voltage(2) OE/ST 1 4 VDD GND 2 3 OUT H = ‘High’, L = ‘Low’ 1) A pull-up resistor of <10 kΩ between OE/ ST pin and Vdd is recommended in high noise environment 2) A Capacitor value of 0.1uF between Vdd and GND is recommended Environmental Environmental Compliance Parameter Condi ons Mechanical Shock MIL-STD-883 Method 2002; (10,000g) Mechanical Vibra on MIL-STD-883 Method 2007; Condi on C 70g Moisture Resistance JESD22-A113; MSL-1 condi ons (125°C 24 hours bake, 85%RH/85°C 168 hours, 3 Reflows 260°C) Temperature Cycle JESD22, Method A104 Solderability MIL-STD-883F, Method 2003 Absolute Maximum RaƟngs A empted opera on outside the absolute maximum ra ngs of the part may cause permanent damage to the part. Actual performance of the IC is only guaranteed within the opera onal specifica ons, not at absolute maximum ra ngs Maximum RaƟngs Parameter Min. Max. Unit Storage Temperature -65 150 °C VDD -0.5 4 V Electrosta c Discharge – 2000 V Soldering Temperature (follow standard Pb free soldering guidelines) – 260 °C Junc on Temperature – 150 °C Thermal Data Thermal ConsideraƟons Package θJA, 4 Layer Board (°C/W) θJA, 2 Layer Board (°C/W) θJC, Bo om (°C/W) 7050 191 263 30 5032 97 199 24 3225 109 212 27 2520 117 222 26 2016 124 227 26 Page 4 of 6 Vectron Interna onal • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • h p://www.vectron.com Rev 1.3 Aug 2014 Ordering InformaƟon HT - MM900A C - 7 F - E E - 25M0000000 Frequency Product HT: High Temperature Feature Pin E: Enable/Disable S: Standby Family MM900A Temp Range C: -55 to 125°C 7: -40 to 125°C F: -40 to 105°C E: -40 to 85°C Package 2: 4 pin 7.0mm x 5.0mm 4: 4 pin 5.0mm x 3.2mm 6: 4 pin 3.2mm x 2.5mm 7: 4 pin 2.5mm x 2.0mm 9: 4 pin 2.0mm x 1.6mm Stability E: ±20ppm F: ±25ppm K: ±50ppm Supply Voltage E: +3.3 Vdc F: +3.0 Vdc G: +2.8 Vdc H: +2.5 Vdc J: +1.8 Vdc Notes: 1. Unless otherwise stated all values are valid a er warm-up me and refer to typical condi ons for supply voltage, load, temperature (25°C). 2. Subject to technical modifica on. 3. Contact factory for availability. 4. Outside standard frequency ranges (see table at right) check with factory for availability Standard Frequency Ranges: Outside this check with Vectron For -40 to 125 C or -40 to 105 C For -55 to 125 C 1.000000 to 61.222999 1.000000 to 61.222999 61.674001 to 69.795999 61.674001 to 69.239999 70.485001 to 79.062999 70.827001 to 78.714999 79.162001 to 81.427999 79.561001 to 80.159999 82.232001 to 91.833999 80.174001 to 80.779999 92.155001 to 94.248999 82.632001 to 91.833999 94.430001 to 94.874999 95.474001 to 96.191999 94.994001 to 97.713999 96.209001 to 96.935999 98.679001 to 110.00000 99.158001 to 110.000000 115.194001 to 117.810999 119.342001 to 120.238999 118.038001 to 118.593999 120.262001 to 121.169999 118.743001 to 122.141999 121.243001 to 121.600999 122.705001 to 123.021999 123.948001 to 137.000000 123.348001 to 137.000000 Page 5 of 6 Vectron Interna onal • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • h p://www.vectron.com Rev 1.3 Aug 2014 Revision History Revision Change Summary Date 1.0 Product Release June 2013 1.1 Knowles logo and address change Feb 2014 1.2 Expanded frequency range to 137MHz 1.3 Add ±20ppm temperature stability March 2014 Aug 2014 For Additional Information, Please Contact USA: Europe: Asia: Vectron Interna onal 267 Lowell Road, Suite 102 Hudson, NH 03051 Tel: 1.888.328.7661 Fax: 1.888.329.8328 Vectron Interna onal Landstrasse, D-74924 Neckarbischofsheim, Germany Tel: +49 (0) 7268.801.100 Fax: +49 (0) 7268.801.282 68 Yin Cheng Road(C), 22nd Floor One Lu Jia Zui Pudong, Shanghai 200120, China Tel: +86 21 6194 6886 Fax: +86 21 6194 6699 Disclaimer Vectron Interna onal reserves the right to make changes to the product(s) and or informa on contained herein without no ce. No liability is assumed as a result of their use or applicaon. No rights under any patent accompany the sale of any such product(s) or informa on. Page 6 of 6 Vectron Interna onal • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • h p://www.vectron.com Rev 1.3 Aug 2014