UNISONIC TECHNOLOGIES CO., LTD MCR106 SCR REVERSE BLOCKING TRIODE THYRISTORS DESCRIPTION PNPN devices designed for high volume consumer applications such as temperature, light and speed control; process and remote control, and warning systems where reliability of operation is important. FEATURES * Glass-passivated surface for reliability and uniformity * Power rated at economical prices * Practical level triggering and holding characteristics * Flat, rugged, thermopad construction for low thermal resistance, high heat dissipation and durability ORDERING INFORMATION Ordering Number Lead Free Halogen Free MCR106L-6-T60-K MCR106G-6-T60-K MCR106L-8-T60-K MCR106G-8-T60-K Note: Pin assignment: G: Gate K: Cathode A: Anode Package TO-126 TO-126 Pin Assignment 1 2 3 K A G K A G Packing Bulk Bulk MARKING MCR106-6 www.unisonic.com.tw Copyright © 2014 Unisonic Technologies Co., Ltd MCR106-8 1 of 3 QW-R301-001.D MCR106 SCR ABSOLUTE MAXIMUM RATINGS (TJ=25°C, unless otherwise specified) PARAMETER SYMBOL RATINGS UNIT 400 V Peak Repetitive Forward and Reverse Blocking MCR106-6 VDRM, VRRM Voltage (Note 1) (TJ=110°C, RGK=1kΩ) MCR106-8 600 V RMS Forward Current (All conduction Angles) IT(RMS) 4 A Average Forward Current (TC=93°C or TA=30°C) IT(AV) 2.55 A Peak Non-repetitive Surge Current ITSM 25 A (1/2 Cycle, 60Hz, TJ=-40 ~ +110°C) Circuit Fusing Considerations (t=8.3 ms) I2t 2.6 A2 S Peak Gate Power PGM 0.5 W Average Gate Power PG(AV) 0.1 W Peak Forward Gate Current IGM 0.2 A Peak Reversed Gate Voltage VRGM 6 V Mounting Torque (Note 2) 6 In. lb. Junction Temperature TJ +110 °C Storage Temperature TSTG -40 ~ +150 °C Notes: 1. VDRM and VRRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent with negative potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage of the devices are exceeded. 2. Torque rating applies with use of compression washer (B52200-F006 or equivalent). Mounting torque in excess of 6 in. lb. does not appreciably lower case-to-sink thermal resistance. Anode lead and heatsink contact pad are common. For soldering purposes (either terminal connection or device mounting), soldering temperatures shall not exceed +200°C. For optimum results, an activated flux (oxide removing) is recommended. 3. Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. THERMAL DATA PARAMETER SYMBOL θJA θJC Junction to Ambient Junction to Case RATINGS 75 3 UNIT °C/W °C/W ELECTRICAL CHARACTERISTICS (TC=25°C and RGK=1000Ω, unless otherwise specified) PARAMETER SYMBOL Peak Forward or Reverse Blocking IDRM,IRRM Current (VAK=Rated VDRM or VRRM) Forward “On” Voltage (ITM=4A peak) VTM Gate Trigger Current (continuous DC) IGT (Note) Gate Trigger Voltage (continuous DC) VGT Gate Non-Trigger Voltage VGD Holding Current IH Forward Voltage Application Rate dv/dt Note: RGK current is not included in measurement. TEST CONDITIONS TJ=25°C TJ=100°C VAK=7V, RL=100Ω VAK=7V, RL=100Ω, TC=-40°C VAK=7V, RL=100Ω, TC=25°C VAK=Rated VDRM, RL=100Ω, TJ=110°C 0.2 VAK=7V, TC=25°C TJ=110°C UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw MIN TYP MAX UNIT 10 μA 200 μA 2 V 200 μA 500 1 V V 5 mA 10 V/s 2 of 3 QW-R301-001.D MCR106 SCR TYPICAL CHARACTERISTICS Maximum Case Temperature Maximum Case Temperature 110 110 106 102 0 98 94 90 86 α π f=60Hz 90 120° dc 180° 80 0 0.4 0.8 1.21.6 2.02.4 2.83.23.6 4.0 Average Forward Current, IT (AV) (A) 50 α π f=60Hz 70 90° α=30° 60° 0 α=30° α=60° α=90° α=180° dc 30 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 Average Forward Current, IT (AV) (A) UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 3 of 3 QW-R301-001.D