www.osram.de/LED-Systeme COINlight® Pro - CP51 Preliminary Data Sheet Benefits Fits in MR16 luminare fixtures Usage without additional heat sink possible - 3.6 W with 50,000h @L70/Ta=25°C - 7.5 W with 25,000h @L70/Ta=25°C Life time up-to 12 times longer vs. Halogen lamps Efficacy up-to 4 times better vs. Halogen lamps Applications Hospitality - Restaurant & Hotel - Corridors & Elevator Shop Technical Operating Data Product Color Number Current Power Radiance of LEDs [A]* [W]* Angle [°]* Color Temp. Lum Lum. Intensity Lum Lum. [K]* [cd]* [lm] Flux CP51-W4F-10-857 white 4 0.51 9,8 36 5700 1600 800 CP51-W4F-8-857 white 3 0.39 7,5 36 5700 1200 600 CP51-W4F-4-857 white 3 0.2 3,6 36 5700 650 320 CP51-W4F-10-827 white 4 0.51 9,8 36 2700 1330 670 CP51 W4F 8 827 CP51-W4F-8-827 white 3 0 39 0.39 75 7,5 36 2700 1000 500 CP51-W4F-4-827 white 3 0.2 3,6 36 2700 540 270 *) All Data are related to the entire module Due to the special conditions of the manufacturing processes of LED the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data +) Preliminary Data Technical Features Module ready to use with three cables: Best efficacy in combination with OSRAM OPTOTRONIC® 24V constant voltage control gears - red cable (+ pole) Recommendation of OPTOTRONIC® OT8, OT20, OT75, OTi DALI 75 - black vable (- pole) - white cable (dimming) Cable length 500 mm, cable Ø 1.6 mm/AWG 22 OT DIM Color Rendering index CRI typ. 85 Lifetime 50.000 hrs L70 B50 @ Tc max Modul efficacy up to 86 lm/W System efficacy up to 76 lm/W CP51 – 10.12.2012 Dimmable by pulse width modulation (PWM) and Page 1 von 5 www.osram.de/LED-Systeme Minimum and Maximum Ratings Product Operating Temperature Storage Temperature Voltage Range Reverse Voltage Forward Voltage at Tc-Point [C°]* [C°]* [V dc]* [V dc]* [V dc]* CP51-W4F-10-857 -30 … 90 -30 … 90 23 … 25 25 24 CP51-W4F-8-857 -30 … 90 -30 … 90 23 … 25 25 24 CP51 W4F 4 857 CP51-W4F-4-857 -30 30 … 90 -30 30 … 90 23 … 25 25 24 CP51-W4F-10-827 -30 … 90 -30 … 90 23 … 25 25 24 CP51-W4F-8-827 -30 … 90 -30 … 90 23 … 25 25 24 CP51-W4F-4-827 -30 … 90 -30 … 90 23 … 25 25 24 *)) Exceeding g maximum ratings g for operating p g and storage g temperature p will reduce expected p life time or destroyy the LED Module. Exceeding maximum ratings for operating current will cause hazardous overload and will likely destroy the LED Module. The temperature of the LED module must be measured at the Tc-point according to EN60598-1 in a thermally constant status with a temperature sensor or a temperature sensitive label. For exact location of the Tc-point see drawing below. Drawing Viewing Angle CP51 – 10.12.2012 Page 2 von 5 www.osram.de/LED-Systeme Safety Information The LED module itself and all its components must not be mechanically stressed. Assembly must not damage or destroy conducting paths on the circuit board. To avoid mechanical damage to the connecting cables, the module should be attached securely to the intended substrate. Heavy vibration should be avoided. In order to drive OSRAM LED-Modules safely, it is absolutely necessary to operate them with an electronically stabilised power supply protecting against short circuits, overload and overheating. To also ease the luminaire/installation approval, electronic control gear for LED or LED modules should carry the CE mark and be ENEC certified. In Europe the declarations of conformity must include the following standards: CE: EC 61347-2-13, EN 55015, IEC 61547 and IEC 61000-3-2 - ENEC: 61347-2-13 and IEC/EN 62384. Also check for the mark of an independent authorized certification institute. Please see the relevant brochure for more detailed information ((see "Related and Further Information"). ) OSRAM OPTOTRONIC® electronic control gear complies to all relevant standards and guarantees safe operation. Installation of LED modules (with power supplies) needs to be made with regard to all applicable electrical and safety standards. Only qualified personnel should be allowed to perform installations. Observe correct polarity! Depending on the product incorrect polarity will lead to emission of red or no light. The module can be destroyed! Correct polarity immediatelly! (see "reverse voltage", page 2). Parallel connection is highly recommended as safe electrical operation mode. Serial connection is not recommended. Unbalanced voltage drop can cause hazardous overload and damage the LED module. Pay attention to ESD steps when mounting the module. In case of thermal overload in the application COINlight Pro CP51 intelligent protection system would switch over into reversible blinking mode. The LED module will not be damaged. Improving heat dissipation by extending the size of the heat sink or reducing the ambient temperature would provide regular operation mode. COINlight Pro works as a three wire system: red cable (pluspole), black cable (minuspole) and a white cable for dimming. If no dimming is required the white and black cables must be connected to the minus pole. A schematic drawing with wiring diagrams for dimming purpose is shown on page 4 "Dimming COINlight PRO CP51“ The module, as manufactured, has no conformal coating and therefore offers no inherent protection against corrosion. Damage by corrosion will not be honored as a materials defect claim. It is the user's responsibility to provide suitable protection against corrosive agents such as moisture and condensation and other harmful elements. If the IP rating of the fixture should be higher than IP20, the design of the housing should be according to the IP standards in the application. CP51 – 10.12.2012 Page 3 von 5 www.osram.de/LED-Systeme Dimming COINlight Professional CP51 CP51 is a high end LED module that can be easily used in various combinations with OSRAM power supplies and light management systems. It can realize dimming functions by connection to a PWM controller. - Dimming range: 100% to 10% flicker free - Frequency: 120 - 300 Hz Three opportunities 1. Operation with power supply – without dimming function Configuration A OT20 OT75 2. Operation with OT EASY 60 – dimming function Configuration B 3. Operation with OT DIM – dimming function Configuration C OT20 / OT75 CP51 – 10.12.2012 Page 4 von 5 www.osram.de/LED-Systeme Assembly Information The mounting of the module can be done with M3 screws and should be done on a metal heat sink! Please pay attention to standard ESD precautions! In order to optimize the thermal management the metal surface needs to be clean (free from dirt and oil) and planar for the best contact with the LED module. Between LED module and mounting surface the use of a thermal interface material (thin layer of heatconductive paste or thermal foil) is recommended. The housing of the COINlight Pro is a primary heat sink. The metal surface increases the cooling effect and prolongs the service life time. The heat sink CPDPHS-51 as accessory part is available for optimized cooling of the module. Ordering Guide Product group Product EAN* S-Unit* COINlight® g Pro CP51-W4F-10-857 4008321 975942 20 COINlight® Pro CP51-W4F-8-857 4008321 975904 20 COINlight® Pro CP51-W4F-4-857 4008321 975867 20 COINlight® Pro CP51-W4F-10-827 4008321 975928 20 COINlight® Pro CP51-W4F-8-827 4008321 975881 20 COINlight® Pro CP51-W4F-4-827 4008321 975843 20 Heat sink CPDPHS-51 4008321 975829 16 *) EAN: Ordering number per single module S-Unit: Modules per shipping unit Note: Typical performance data are subject to change without any further notice, particularly as LED technology evolves. Sales and Technical Support OSRAM AG Hellabrunner Strasse 1 Sales and technical support is given by the local D - 81536 München Germany OSRAM subsidiaries. www.osram.com On our world wide homepage all OSRAM subsidiaries are listed with complete address Phone: +49 (0)89 6213-0 and phone numbers. Related and Further Information A new approach to light OSRAM LED Systeme OPTOTRONIC® Technical Guide OPTOTRONIC® Data sheets Eulumdat Files New standards for LED control gear CP51 – 10.12.2012 153 S006 GB www osram de/led systeme www.osram.de/led-systeme 130 T008 DE www.osram.de/evg-downloads http://catalog.myosram.com www.osram.de/led-systeme-downloads www.osram.de/evg-downloads Page 5 von 5