DRAGONchain Colormix - DC24A-H

www.osram.com/LED-Systems
DRAGONchain Colormix - DC24A-H
Data Sheet
Benefits
Picture for
Datasheet
is missing
!!!
¾
Outdoor LED-chain for dynamic colored
backlighting
¾
RGB-LED with special optics for very high
color homogeneity
Applications
¾
Large lightboxes, replacement of colored
FL tubes
¾
Moodlighting, inground mounted tiles
¾
Spa-, fair- or shoplighting
Technical Operating Data
Product
Color
Number of
LEDs
Voltage
[V DC]*
Power
[W]*
Current
[A]*
Radiance
Angle [°]*
Wavelength [nm]
Color Temp [K]*
Lum. Flux
[lm]*
DC24A-RGB-H
DC24A-RGB-H
red
green
24
24
24
24
9,6
8,4
0,4
0,35
135
135
625 nm
525 nm
285
505
DC24A-RGB-H
blue
24
24
3,2
0,13
135
467 nm
55
*) All Data are related to the entire module
Due to the special conditions of the manufacturing processes of LED the typical data of technical parameters can only reflect statistical figures and do not necessarily
correspond to the actual parameters of each single product which could differ from the typical data. This product was not optimized for white light illumination.
+) Preliminary Data
Technical Features
¾ Total maximum power / brightness:
¾ 1 indivisible chain consisting of 6 platines with
23W / 845 lm (@Tc=25°C)
each 4 LED Golden DRAGON
¾ Dimensions (L x B x H):
¾ Safe mounting by means of screws M3
3000 mm x 64 mm x 24 mm
¾ Integrated heatsink
¾ Very broad beampattern for homogenous light
accross the whole backlight diffusor
wires (500 mm)
¾ IP65 rated housing allowing for outdoor
applications
DC24A-H - 23.06.2009
¾ Easy connection with integrated color coded
Page 1 of 4
¾ 2 chains can be driven by 1 OT EASY 60 device
Minimum and Maximum Ratings
Product
DC24A-RGB-H
*)
Operating Temperature
at Tc-Point [ °C ] *
Storage Temperature
[ °C ] *
Voltage Range
[ V dc ] *
Reverse Voltage
[ V dc ] *
-30 ... 85
-40 ... 85
23 ... 25
25
Exceeding maximum ratings for operating and storage temperature will reduce expected life time or destroy the LED Module.
Exceeding maximum ratings for operating voltage will cause hazardous overload and will likely destroy the LED Module.
The temperature of the LED module must be measured at the Tc-point according to EN60598-1 in a thermally constant status with a temperature sensor or a temperature
sensitive label. Drive all channels on 100% to determine the temperature. For exact location of the Tc-point see drawing below.
Drawings
Drawing is missing !!!
DC24A-H - 23.06.2009
Page 2 of 4
Safety Information
¾ The LED module itself and all its components must not be mechanically stressed.
¾ Assembly must not damage or destroy conducting paths on the circuit board.
¾ The PCBs must be connected ideally to a thermally conducting surface. Otherwise the lifetime of the modules shortens. Please also
notice our application note “Lifetime”
¾ The maximum temperature ranges are to be maintained (see page 2)
In order to drive OSRAM LED-Modules safely, it is absolutely necessary to operate them with an electronically
stabilised power supply protecting against short circuits, overload and overheating.
To also ease the luminaire/installation approval, electronic control gear for LED or LED modules should carry the CE mark and be
ENEC certified. In Europe the declarations of conformity must include the following standards:
CE: EC 61374-2-13, EN 55015, IEC 61547 and IEC 61000-3-2 - ENEC: 61374-2-13 and IEC/EN 62384.
Also check for the mark of an independent authorized certification institute.
Please see the relevant brochure for more detailed information (see "Related and Further Information")
OSRAM OPTOTRONIC® electronic control gear complies to all relevant standards and guarantees safe operation.
¾ Installation of LED modules (with power supplies) needs to be made with regard to all applicable electrical and safety standards.
Only qualified personnel should be allowed to perform installations.
¾ Observe correct polarity!
Depending on the product incorrect polarity will lead to emission of red or no light. The module can be destroyed! Correct polarity
immediatelly! (see "reverse voltage", page 2)
¾ Parallel connection is highly recommended as safe electrical operation mode.
Serial connection is not recommended. Unbalanced voltage drop can cause hazardous overload and damage the LED module.
¾ The chain must not me divided
¾ Dimming / colorcontrolling is only possible with PWM
¾ Pay attention to standard ESD precautions when installing the module. Avoid touching metallic parts.
¾ The DRAGONchain Colormix is driven ideally by OSRAM OPTOTRONIC power supplies and controllgear. Controllgear is available
with 1..10V, DALI or DMX interface.
¾ 2 Modules DC24A-RGB can be driven by 1 OT EASY 60
¾ 1 Powersupplies OPTOTRONIC OT75E can drive 3 modules. Please refer to the maximum currents of the controllgear when
calculating the whole installation (OT DIM: 5A, OTi DIM: 5A, OT DMX, 3-Channel DIM or Sequencer: 2A per channel). Please read
our OPTOTRONIC technical installation guide for more detailed information about calculation and wiring diagrams.
¾ The LED-chain can typically survive transient totalcurrent levels of up to 1,3 Amperes. As a general design precaution, if the
maximum output current of the power supply is more than 1,3 Amperes, fast-blow fuses should be incorporated into the wiring plan.
DC24A-H - 23.06.2009
Page 3 of 4
Assembly Information
¾ The mounting of the module is facilitated by means of M3 screws.
¾ One chain DC24A can already illuminate a light box with a surface of 1m² with about 100 cd/m². See the following information:
Distance LED <-> Diffusor: min. 20 cm. Transmissivity: max. 25%.
With two chains you can reach 380 cd/m². See therefore following information:
Distance LED <-> Diffusor: min. 14 cm. Transmissivity: max. 45%.
¾ The black wire must be attached to the '+' 24V output of the controllgear. The others are to be connected according to their colors to
the 'R-', 'B-' und 'G-' channels.
¾ If white light is to be shown for a longer period we recommend enlarging the distance between LED and diffusor.
¾ The interior of the lightbox should be completely white.
¾ The ribboncable between the PCBs should be fixed flat, so that they cannot produce any shadows or inhomogeneities. The ribbon
cables between the boards may be bended but not damaged.They may be bended only once per bending point.
Ordering Guide
Productgroup
Productname
EAN *
DRAGONchain Colormix
DC24A-RGB-H
40084008321254658
*) EAN: Ordering number per single module
S-Unit: Modules per shipping unit
Note: Typical performance data are subject to change without any further notice, particularly as LED technology evolves.
Sales and Technical Support
OSRAM GmbH
Hellabrunner Strasse 1
D - 81536 München
Germany
www.osram.com
+49 (0)89 6213-0
Sales and technical support is given by the
local OSRAM subsidiaries.
On our world wide homepage all OSRAM
subsidiaries are listed with complete
address and phone numbers.
Related and Further Information
¾ The new dimension of light
¾
¾
¾
¾
153 S006 GB
www.osram.com/led-systems-downloads
130 T008 GB www.osram.com/ecg-downloads
http://catalog.myosram.com
www.osram.com/led-systems
130 W011 GB
www.osram.com/ecg-download
OPTOTRONIC® Technical Guide
OPTOTRONIC® Data Sheets
OSRAM LED systems
New standards for LED control gear
DC24A-H - 23.06.2009
Page 4 of 4
S-Unit *
6