ABS210 - Thinki Semiconductor Co.,Ltd.

ABS210
®
Pb Free Plating Product
Pb
ABS210
2.0 Ampere Surface Mount Miniature Bridge Rectifier
SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIERS
Voltage Range - 1000 Volts
Current - 1.6/2.0 Ampere
FEATURES
ABS
Ideal for printed circuit board
Reliable low cost construction utilizing
molded plastic technique
High temperature soldering guaranteed:
260 /10 seconds at 5 lbs., (2.3kg) tension
Small size, simple installation
High surge current capability
Glass passivated chip junction
MECHANICAL DATA
Case: Molded plastic body
Terminals: Plated leads solderable per MIL-STD-750,
Method 2026
Polarity: Polarity symbols marked on case
Mounting Position: Any
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25 ambient temperature unless otherwise specified.
Single phase half-wave 60Hz,resistive or inductive load, for capacitive load derate current by 20%.
Maximum repetitive peak reverse voltage
Maximum RMS voltage
Maximum DC blocking voltage
Maximum average forward rectified current
On glass-epoxy P.C.B.(Note1)
On aluminum substrate(Note2)
Peak forward surge current,
8.3ms single half sine-wave superimposed on
rated load (JEDEC Method)
Maximum instantaneous forward voltage drop
per leg at 0.8A
Maximum DC reverse current
TA=25
at rated DC blocking voltage
TA=100
Operating temperature range
storage temperature range
SYMBOLS
ABS210
UNITS
VRRM
VRMS
VDC
1000
700
1000
VOLTS
VOLTS
VOLTS
IF(AV)
1.6
2.0
Amps
IFSM
60
Amps
VF
0.95
Volts
5
100
-55 to +150
-55 to +150
uA
uA
IR
TJ
TSTG
NOTES:1.On glass epoxy P.C.B. mounted on 0.05x0.05''(1.3x1.3mm) pads
2.On aluminum substrate P.C.B. with on area of 0.8''x0.8''(20x20mm) mounted on 0.05X0.05''(1.3X1.3mm) solder pad
Rev.05
© 2006 Thinki Semiconductor Co.,Ltd.
Page 1/2
http://www.thinkisemi.com/
ABS210
®
RATINGS AND CHARACTERISTIC CURVES ABS210
Instantaneous Forward Current, (A)
FIG.1 TYPICAL FORWARD CHARACTERISTICS
FIG.2 FORWARD DERATING CURVE
2.0
2.0
Average Forward Rectified
Current, (A)
Aluminum Substrate
0.8
0.2
0.02
1.50
GLASS
EPOXY
P.C.B
0.10
0.50
RESISTIVE OR INDUCTIVE LOAD
0
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
0
Instantaneous Forward Voltage, ( V )
FIG.3 TYPICAL REVERSE CHARACTERISTICS
50
75
100
125
150
Ambient Temperature, (°C )
FIG.4 PEAK FORWARD SURGE CURRENT
70
Peak Forward Surge Current,
(A)
100000
Instantaneous Reverse Leakage
Current, ( A)
25
10000
1000
TA=100°C
100
TA=25°C
10
1.0
60
50
40
30
20
10
0
0
20
40
60
80
100
120
140
Percent Of Rated Peak Reverse Voltage, %
Rev.05
© 2006 Thinki Semiconductor Co.,Ltd.
1
10
100
Number Of Cycles At 60Hz
Page 2/2
http://www.thinkisemi.com/