RT380T 230/400 PCB RoHS Analog three-phase thyristor trigger module • Two supply voltages: 230 Vac or 400Vac • Supply with external trafo up to 690 Vac • Screwless terminal blocks • Control voltage selectable 0-5/0-10V • External inhibit input • 4.000 V galvanic insulation • Triggers the whole range SEMIKRON • No external components needed TECHNICAL SPECIFICATIONS Supply voltage Power drain Input voltages Output signals Trigger current Isolation Working frequency Working temperature Humidity Power-on Weight 230/400 VAC +10% / -15% 8 VA max. 7-16 Vcc 0 - 5 Vcc (15 Vcc max.) 0 - 10 Vcc (15 Vcc max.) 5 Vcc 100 mA max. 600 mA @ VGT = 5V 4000Vca inlet/outlet 45-65Hz (automatic adaptation) 5 - 50ºC 10 - 95% without condensation 1 second 525 g INHIBIT-IN 0-5 V IN 0-10 V IN +5V OUT This module has been designed for triggering 6 thyristors with phase regulation in order to control the power on the load. It is recommended the use of external RC-snubbers to protect the thyristors and to facilitate its triggering. The load may be supplied with a variable alternating voltage if the 6 thyristors are connected in antiparallel W3C, or with a variable direct voltage if they are connected in B6C, B6HK or B6HKF. The external thermal trip has to be normally close. If it opens, the module stops, the green LED stops lighting and the red LED lights. The module has an automatic Power-on delay of approx. 1 second. That means that during the first second the output is inhibited (no pulse output). It is important to connect the three phases and the outputs of gates and cathodes exactly as shown in the label. Done this, the input phases of the whole equipment (module + power) can be connected in the sequence you want. To select the thyristors connection W3C, the three minidips have to be in W3C position. For a B6C connection, they have to be in B6C position. An input of +12V (7 to 16V) in the input INHIBIT stops the output of gate pulses and red LED starts lighting. This +12V can be external or using the internal auxiliary 12VDC present at the thermal trip jumper (see drawing). 14/04/00 19 30 max Semikron Electronics SL posee el copyright de este plano. Se autoriza su uso única y exclusivamente para el fin para el que ha sido enviado. No se permite su reproducción sin el consentimiento escrito previo de los autores. 2 4, K1 G1 K4 G4 K3 G3 175 K6 G6 K5 G5 CN2 K2 G2 5 157,50 Input Thermal trip Supply 230 Vac 5V 0V 5V 10V out in in CN3 CN1 W3C Inhibit B6C T S R Supply 400 Vac T S 17,50 R 0 Green LED - Thermal trip 10 0 135 125 Red LED - Inhibit G1 K1 INPUT THERMALTRIP Thermaltrip with contacts normally Closed R +12V To inhibit the output pulses connect the +12V of the input thermaltrip to the terminal "INHIBIT" G1 T S R K1 G3 K3 G5 K5 U K2 + G2 V S K4 G4 G2 K2 G4 K4 G6 K6 1:2 Tolerancia Acabado Entre Centros: 0.25 Métrica: 0.5 G5 K5 W T Escala Material G3 K3 K6 G6 Denominación Código RT380T 230/400 PCB RoHS Artículo 97492031 Dibujado CO Revisado Rev. 0 29/04/09 RT380Tpcb Fecha