S i 4 4 6 4 / 6 3 / 6 1/60 H I G H - P ERFORMANCE , L O W -C U R R E N T T RANSCEIVER Features Pin Assignments SDN 1 20 19 18 17 16 RXp 2 Applications 15 nSEL RXn 3 14 SDI GND PAD TX 4 13 SDO NC 5 12 SCLK 6 7 8 9 GPIO0 Remote keyless entry Home automation Industrial control Sensor networks Health monitors Electronic shelf labels VDD TXRamp Smart metering (802.15.4g & MBus) Remote control Home security and alarm Telemetry Garage and gate openers VDD XOUT XIN GND Power supply = 1.8 to 3.6 V Excellent selectivity performance 60 dB adjacent channel 75 dB blocking at 1 MHz Antenna diversity and T/R switch control Highly configurable packet handler TX and RX 64 byte FIFOs Auto frequency control (AFC) Automatic gain control (AGC) Low BOM Low battery detector Temperature sensor 20-Pin QFN package IEEE 802.15.4g compliant FCC Part 90 Mask D, FCC part 15.247, 15,231, 15,249, ARIB T-108, T-96, T-67, RCR STD-30, China regulatory ETSI Class-I Operation with SAW 10 11 nIRQ GPIO1 Frequency range = 119–1050 MHz Receive sensitivity = –126 dBm Modulation (G)FSK, 4(G)FSK, (G)MSK OOK Max output power +20 dBm (Si4464/63) +16 dBm (Si4461) +13 dBm (Si4460) PA support for +27 or +30 dBm Low active power consumption 10/13 mA RX 18 mA TX at +10 dBm (Si4460) Ultra low current powerdown modes 30 nA shutdown, 50 nA standby Data rate = 100 bps to 1 Mbps Fast wake and hop times GPIO2 GPIO3 Description Patents pending Silicon Laboratories' Si446x devices are high-performance, low-current transceivers covering the sub-GHz frequency bands from 119 to 1050 MHz. The radios are part of the EZRadioPRO® family, which includes a complete line of transmitters, receivers, and transceivers covering a wide range of applications. All parts offer outstanding sensitivity of –126 dBm while achieving extremely low active and standby current consumption. The Si4463/61/60 offers frequency coverage in all major bands. The Si4464 offers frequency coverage in bands not covered by Si4463/61/60. Typically, these are non-standard frequencies or licensed frequency bands. The Si446x includes optimal phase noise, blocking, and selectivity performance for narrow band and licensed band applications, such as FCC Part90 and 169 MHz wireless Mbus. The 60 dB adjacent channel selectivity with 12.5 kHz channel spacing ensures robust receive operation in harsh RF conditions, which is particularly important for narrow band operation. The Si4464/63 offers exceptional output power of up to +20 dBm with outstanding TX efficiency. The high output power and sensitivity results in an industry-leading link budget of 146 dB allowing extended ranges and highly robust communication links. The Si4460 active mode TX current consumption of 18 mA at +10 dBm and RX current of 10 mA coupled with extremely low standby current and fast wake times ensure extended battery life in the most demanding applications. The Si4464/63 can achieve up to +27 dBm output power with built-in ramping control of a low-cost external FET. The devices can meet worldwide regulatory standards: FCC, ETSI, and ARIB. All devices are designed to be compliant with 802.15.4g and WMbus smart metering standards. The devices are highly flexible and can be configured via the Wireless Development Suite (WDS) available on the Silicon Labs web site. Rev 1.2 12/12 Copyright © 2012 by Silicon Laboratories Si4464/63/62/61/60 Si4464/63/61/60 Functional Block Diagram GPIO3 GPIO2 XIN XOUT Loop Filter PFD / CP VCO FBDIV TX DIV SDN RXN TX LO Gen Bootup OSC IF PKDET RF PKDET LNA PA PGA nSEL SDI SDO SCLK nIRQ LDOs Digital Logic POR LBD 32K LP OSC PA LDO 2 ADC PowerRamp Cntl VDD MODEM FIFO Packet Handler SPI Interface Controller RXP 30 MHz XO Frac-N Div TXRAMP VDD GPIO0 GPIO1 Product Freq. Range Max Output Power TX Current RX Current Narrow Band Support Image Cal Si4464 Banded 119–960 MHz +20 dBm 915 MHz: 85 mA 10.6/13.6 mA Si4463 Major bands 142-1050 MHz +20 dBm 169 MHz: 70 mA 915 MHz: 85 mA 10/13 mA Si4461 Major bands 142-1050 MHz +16 dBm +13 dBm: 29 mA +14 dBm: 33 mA 10/13 mA Si4460 Major bands 142-1050 MHz +13 dBm +10 dBm: 18 mA +11 dBm: 20 mA 10/13 mA Rev 1.2 Si4464/63/61/60 TABLE O F C ONTENTS Section Page 1. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 1.1. Definition of Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 3. Controller Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 3.1. Serial Peripheral Interface (SPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 3.2. Fast Response Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 3.3. Operating Modes and Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 3.4. Application Programming Interface (API) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3.5. Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3.6. GPIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 4. Modulation and Hardware Configuration Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 4.1. MODEM_MOD_TYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 4.2. Modulation Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4.3. Hardware Configuration Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4.4. Preamble Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 5. Internal Functional Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 5.1. RX Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 5.2. RX Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 5.3. Synthesizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 5.4. Transmitter (TX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 5.5. Crystal Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 6. Data Handling and Packet Handler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 6.1. RX and TX FIFOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 6.2. Packet Handler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 7. RX Modem Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 8. Auxiliary Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 8.1. Wake-up Timer and 32 kHz Clock Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 8.2. Low Duty Cycle Mode (Auto RX Wake-Up) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 8.3. Temperature, Battery Voltage, and Auxiliary ADC . . . . . . . . . . . . . . . . . . . . . . . . . . 44 8.4. Low Battery Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 8.5. Antenna Diversity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 9. Pin Descriptions: Si4464/63/61/60 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 10. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 11. Package Outline: Si4464/63/61/60 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 12. PCB Land Pattern: Si4464/63/61/60 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 13. Top Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 13.1. Si4464/63/61/60 Top Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 13.2. Top Marking Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 Rev 1.2 3 Si4464/63/61/60 1. Electrical Specifications Table 1. DC Characteristics1 Parameter Supply Voltage Range Symbol Min Typ Max Unit 1.8 3.3 3.6 V RC Oscillator, Main Digital Regulator, and Low Power Digital Regulator OFF — 30 — nA IStandby Register values maintained and RC oscillator/WUT OFF — 50 — nA ISleepRC RC Oscillator/WUT ON and all register values maintained, and all other blocks OFF — 900 — nA ISleepXO Sleep current using an external 32 kHz crystal.2 — 1.7 — µA ISensor Low battery detector ON, register values maintained, and all other blocks OFF — 1 — µA IReady Crystal Oscillator and Main Digital Regulator ON, all other blocks OFF — 1.8 — mA ITune_RX RX Tune, High Performance Mode — 7.2 — mA ITune_TX TX Tune, High Performance Mode — 8 — mA IRXH High Performance Mode — 13.7 — mA — 10.7 — mA +20 dBm output power, class-E match, 915 MHz, 3.3 V — 85 — mA +20 dBm output power, class-E match, 460 MHz, 3.3 V — 75 — mA +20 dBm output power, square-wave match, 169 MHz, 3.3 V — 70 — mA ITX_+16 +16 dBm output power, class-E match, 868 MHz, 3.3 V2 — 43 — mA ITX_+14 +14 dBm output power, Switched-current match, 868 MHz, 3.3 V2 — 37 — mA ITX_+13 +13 dBm output power, switched-current match, 868 MHz, 3.3 V2 — 29 — mA ITX_+10 +10 dBm output power, Class-E match, 868 MHz, 3.3 V2 — 18 — mA VDD Power Saving Modes IShutdown -LBD TUNE Mode Current RX Mode Current IRXL TX Mode Current (Si4464/63) TX Mode Current (Si4461) TX Mode Current (Si4460) Test Condition ITX_+20 Low Power Mode2 Notes: 1. All specifications guaranteed by production test unless otherwise noted. Production test conditions and max limits are listed in the "Production Test Conditions" section of "1.1. Definition of Test Conditions" on page 14. 2. Guaranteed by qualification. Qualification test conditions are listed in the “Qualification Test Conditions” section in "1.1. Definition of Test Conditions" on page 14. 4 Rev 1.2 Si4464/63/61/60 Table 2. Synthesizer AC Electrical Characteristics1 Parameter Synthesizer Frequency Range (Si4463/61/60) Synthesizer Frequency Range (Si4464) Synthesizer Frequency Resolution3 Symbol Test Condition FSYN FSYN Min Typ Max Unit 850 — 1050 MHz 420 — 525 MHz 284 — 350 MHz 142 — 175 MHz 705 — 960 MHz 353 — 639 MHz 177 — 319 MHz 119 — 159 MHz FRES-960 850–1050 MHz — 28.6 — Hz FRES-525 420–525 MHz — 14.3 — Hz FRES-350 283–350 MHz — 9.5 — Hz FRES-175 142–175 MHz — 4.7 — Hz FRES-960 705–960 MHz — 28.6 — Hz FRES-639 470–639 MHz — 19.1 — Hz FRES-479 353–479 MHz — 14.3 — Hz FRES-319 235–319 MHz — 9.5 — Hz FRES-239 177–239 MHz — 7.1 — Hz FRES-159 119–159 MHz — 4.7 — Hz Synthesizer Settling Time4 tLOCK Measured from exiting Ready mode with XOSC running to any frequency. Including VCO Calibration. — 50 — µs Phase Noise4 L(fM) F = 10 kHz, 460 MHz, High Perf Mode — –106 — dBc/Hz F = 100 kHz, 460 MHz, High Perf Mode — –110 — dBc/Hz F = 1 MHz, 460 MHz, High Perf Mode — –123 — dBc/Hz F = 10 MHz, 460 MHz, High Perf Mode — –130 — dBc/Hz Synthesizer Frequency Resolution (Si4464)3 Notes: 1. All specification guaranteed by production test unless otherwise noted. Production test conditions and max limits are listed in the “Production Test Conditions” section in "1.1. Definition of Test Conditions" on page 14. 2. For applications that use the major bands covered by Si4463/61/60, customers should use those parts instead of Si4464. 3. Default API setting for modulation deviation resolution is double the typical value specified. 4. Guaranteed by qualification. Qualification test conditions are listed in the "Qualification Test Conditions" section in "1.1. Definition of Test Conditions" on page 14. Rev 1.2 5 Si4464/63/61/60 Table 3. Receiver AC Electrical Characteristics1 Parameter RX Frequency Range (Si4463/61/60) RX Frequency Range (Si4464) Symbol Test Condition FRX FRX Min Typ Max Unit 850 — 1050 MHz 420 — 525 MHz 284 — 350 MHz 142 — 175 MHz 705 — 960 MHz 353 — 639 MHz 177 — 319 MHz 119 — 159 MHz Notes: 1. All specification guaranteed by production test unless otherwise noted. Production test conditions and max limits are listed in the "Production Test Conditions" section in "1.1. Definition of Test Conditions" on page 14. 2. For applications that use the major bands covered by Si4463/61/60, customers should use those parts instead of Si4464. 3. Guaranteed by qualification. BER is specified for the 450–470 MHz band. Qualification test conditions are listed in the "Qualification Test Conditions" section in "1.1. Definition of Test Conditions" on page 14. 4. For PER tests, 48 preamble symbols, 4 byte sync word, 10 byte payload and CRC-32 was used. PER and BER tested in the 450–470 MHz band. 5. Guaranteed by bench characterization. 6 Rev 1.2 Si4464/63/61/60 Table 3. Receiver AC Electrical Characteristics1 (Continued) Parameter RX Sensitivity Symbol Test Condition Min Typ Max Unit PRX_0.5 (BER < 0.1%) (500 bps, GFSK, BT = 0.5, f = 250Hz)3 — –126 — dBm PRX_40 (BER < 0.1%) (40 kbps, GFSK, BT = 0.5, f = 20 kHz)3 — –110 — dBm PRX_100 (BER < 0.1%) (100 kbps, GFSK, BT = 0.5, f = 50 kHz)1 — –106 — dBm PRX_125 (BER < 0.1%) (125 kbps, GFSK, BT = 0.5, f = 62.5 kHz)3 — –105 — dBm PRX_500 (BER < 0.1%) (500 kbps, GFSK, BT = 0.5, f = 250 kHz)3 — –97 — dBm PRX_9.6 (PER 1%) (9.6 kbps, 4GFSK, BT = 0.5, f = kHz)3,4 — –110 — dBm PRX_1M (PER 1%) (1 Mbps, 4GFSK, BT = 0.5, inner deviation = 83.3 kHz)3,4 — –88 — dBm PRX_OOK (BER < 0.1%, 4.8 kbps, 350 kHz BW, OOK, PN15 data)3 — –110 — dBm (BER < 0.1%, 40 kbps, 350 kHz BW, OOK, PN15 data)3 — –104 — dBm (BER < 0.1%, 120 kbps, 350 kHz BW, OOK, PN15 data)3 — –99 — dBm 1.1 — 850 kHz — 0 0.1 ppm — ±0.5 — dB RX Channel Bandwidth5 BW BER Variation vs Power Level3 PRX_RES RSSI Resolution RESRSSI Up to +5 dBm Input Level Notes: 1. All specification guaranteed by production test unless otherwise noted. Production test conditions and max limits are listed in the "Production Test Conditions" section in "1.1. Definition of Test Conditions" on page 14. 2. For applications that use the major bands covered by Si4463/61/60, customers should use those parts instead of Si4464. 3. Guaranteed by qualification. BER is specified for the 450–470 MHz band. Qualification test conditions are listed in the "Qualification Test Conditions" section in "1.1. Definition of Test Conditions" on page 14. 4. For PER tests, 48 preamble symbols, 4 byte sync word, 10 byte payload and CRC-32 was used. PER and BER tested in the 450–470 MHz band. 5. Guaranteed by bench characterization. Rev 1.2 7 Si4464/63/61/60 Table 3. Receiver AC Electrical Characteristics1 (Continued) Parameter Symbol Test Condition Min Typ Max Unit 1-Ch Offset Selectivity, 169 MHz3 C/I1-CH — –60 — dB 1-Ch Offset Selectivity, 450 MHz3 C/I1-CH — –58 — dB 1-Ch Offset Selectivity, 868 / 915 MHz3 C/I1-CH Desired Ref Signal 3 dB above sensitivity, BER < 0.1%. Interferer is CW, and desired is modulated with 2.4 kbps F = 1.2 kHz GFSK with BT = 0.5, RX channel BW = 4.8 kHz, channel spacing = 12.5 kHz — –53 — dB Blocking 1 MHz Offset3 1MBLOCK — –75 — dB Blocking 8 MHz Offset3 8MBLOCK — –84 — dB — 35 — dB — 55 — dB Image Rejection3 ImREJ Desired Ref Signal 3 dB above sensitivity, BER = 0.1%. Interferer is CW, and desired is modulated with 2.4 kbps, F = 1.2 kHz GFSK with BT = 0.5, RX channel BW = 4.8 kHz No image rejection calibration. Rejection at the image frequency. IF = 468 kHz With image rejection calibration in Si446x. Rejection at the image frequency. IF = 468 kHz Notes: 1. All specification guaranteed by production test unless otherwise noted. Production test conditions and max limits are listed in the "Production Test Conditions" section in "1.1. Definition of Test Conditions" on page 14. 2. For applications that use the major bands covered by Si4463/61/60, customers should use those parts instead of Si4464. 3. Guaranteed by qualification. BER is specified for the 450–470 MHz band. Qualification test conditions are listed in the "Qualification Test Conditions" section in "1.1. Definition of Test Conditions" on page 14. 4. For PER tests, 48 preamble symbols, 4 byte sync word, 10 byte payload and CRC-32 was used. PER and BER tested in the 450–470 MHz band. 5. Guaranteed by bench characterization. 8 Rev 1.2 Si4464/63/61/60 Table 4. Transmitter AC Electrical Characteristics1 Parameter Symbol Test Condition TX Frequency Range (Si4463/61/60) Min Typ Max Unit 850 — 1050 MHz 420 — 525 MHz 284 — 350 MHz 142 — 175 MHz 705 — 960 MHz 353 — 639 MHz 177 — 319 MHz 119 — 159 MHz FTX TX Frequency Range (Si4464) FTX (G)FSK Data Rate3,4 DRFSK 0.1 — 500 kbps 4(G)FSK Data Rate3,4 DR4FSK 0.2 — 1000 kbps OOK Data Rate3,4 DROOK 0.1 — 120 kbps Modulation Deviation Range3 Modulation Deviation Range (Si4464)3 f960 850–1050 MHz — 1.5 — MHz f525 420–525 MHz — 750 — kHz f350 283–350 MHz — 500 — kHz f175 142–175 MHz — 250 — kHz f960 705–960 MHz — 1.5 — MHz f639 470–639 MHz — 1 — MHz f479 353–479 MHz — 750 — kHz f319 235–319 MHz — 500 — kHz f239 177–239 MHz — 375 — kHz f159 119–159 MHz — 250 — kHz Notes: 1. All specification guaranteed by production test unless otherwise noted. Production test conditions and max limits are listed in the "Production Test Conditions" section in "1.1. Definition of Test Conditions" on page 14. 2. For applications that use the major bands covered by Si4463/61/60, customers should use those parts instead of Si4464. 3. Guaranteed by qualification. Qualification test conditions are listed in the "Qualification Test Conditions" section in "1.1. Definition of Test Conditions" on page 14. 4. The maximum data rate is dependant on the XTAL frequency and is calculated as per the formula: Maximum Symbol Rate = Fxtal/60, where Fxtal is the XTAL frequency (typically 30 MHz). 5. Default API setting for modulation deviation resolution is double the typical value specified. 6. Output power is dependent on matching components and board layout. Rev 1.2 9 Si4464/63/61/60 Table 4. Transmitter AC Electrical Characteristics1 (Continued) Parameter Modulation Deviation Resolution2,5 Modulation Deviation Resolution (Si4464)3 Symbol Test Condition Min Typ Max Unit FRES-960 850–1050 MHz — 28.6 — Hz FRES-525 420–525 MHz — 14.3 — Hz FRES-350 283–350 MHz — 9.5 — Hz FRES-175 142–175 MHz — 4.7 — Hz FRES-960 705–960 MHz — 28.6 — Hz FRES-639 470–639 MHz — 19.1 — Hz FRES-479 353–479 MHz — 14.3 — Hz FRES-319 235–319 MHz — 9.5 — Hz FRES-239 177–239 MHz — 7.1 — Hz FRES-159 119–159 MHz — 4.7 — Hz Output Power Range (Si4464/63)6 PTX –20 — +20 dBm Output Power Range (Si4461)6 PTX61 –40 — +16 dBm Output Power Range (Si4460)6 PTX60 –40 — +13 dBm TX RF Output Steps3 PRF_OUT Using switched current match within 6 dB of max power — 0.1 — dB TX RF Output Level3 Variation vs. Temperature PRF_TEMP –40 to +85 C — 1 — dB TX RF Output Level Variation vs. Frequency3 PRF_FREQ Measured across 902–928 MHz — 0.5 — dB B*T Gaussian Filtering Bandwith Time Product — 0.5 — Transmit Modulation Filtering3 Notes: 1. All specification guaranteed by production test unless otherwise noted. Production test conditions and max limits are listed in the "Production Test Conditions" section in "1.1. Definition of Test Conditions" on page 14. 2. For applications that use the major bands covered by Si4463/61/60, customers should use those parts instead of Si4464. 3. Guaranteed by qualification. Qualification test conditions are listed in the "Qualification Test Conditions" section in "1.1. Definition of Test Conditions" on page 14. 4. The maximum data rate is dependant on the XTAL frequency and is calculated as per the formula: Maximum Symbol Rate = Fxtal/60, where Fxtal is the XTAL frequency (typically 30 MHz). 5. Default API setting for modulation deviation resolution is double the typical value specified. 6. Output power is dependent on matching components and board layout. 10 Rev 1.2 Si4464/63/61/60 Table 5. Auxiliary Block Specifications1 Parameter Symbol Test Condition Min Typ Max Unit Temperature Sensor Sensitivity2 TSS — 4.5 — ADC Codes/ °C Low Battery Detector Resolution LBDRES — 50 — mV Microcontroller Clock Output Frequency Range3 Temperature Sensor Conversion2 XTAL Range4 30 MHz XTAL Start-Up Time 30 MHz XTAL Cap Resolution2 32 kHz XTAL Start-Up Time2 32 kHz Accuracy using Internal RC Oscillator2 POR Reset Time FMC Configurable to Fxtal or Fxtal divided by 2, 3, 7.5, 10, 15, or 30 where Fxtal is the reference XTAL frequency. In addition, 32.768 kHz is also supported. 32.768K — Fxtal Hz TEMPCT Programmable setting — 3 — ms 32 MHz XTALRange t30M 25 Using XTAL and board layout in reference design. Start-up time will vary with XTAL type and board layout. — 250 — µs 30MRES — 70 — fF t32k — 2 — sec 32KRCRES — 2500 — ppm tPOR — — 5 ms Notes: 1. All specification guaranteed by production test unless otherwise noted. Production test conditions and max limits are listed in the "Production Test Conditions" section in "1.1. Definition of Test Conditions" on page 14. 2. Guaranteed by qualification. Qualification test conditions are listed in the "Qualification Test Conditions" section in "1.1. Definition of Test Conditions" on page 14. 3. Microcontroller clock frequency tested in production at 1 MHz, 30 MHz and 32.768 kHz. Other frequencies tested in bench characterization. 4. XTAL Range tested in production using an external clock source (similar to using a TCXO). Rev 1.2 11 Si4464/63/61/60 Table 6. Digital IO Specifications (GPIO_x, SCLK, SDO, SDI, nSEL, nIRQ, SDN)1 Parameter Rise Time 2,3 Fall Time3,4 Symbol Test Condition Min Typ Max Unit TRISE 0.1 x VDD to 0.9 x VDD, CL = 10 pF, DRV<1:0> = HH — 2.3 — ns TFALL 0.9 x VDD to 0.1 x VDD, CL = 10 pF, DRV<1:0> = HH — 2 — ns Input Capacitance CIN — 2 — pF Logic High Level Input Voltage VIH VDD x 0.7 — — V Logic Low Level Input Voltage VIL — — VDD x 0.3 V Input Current IIN 0<VIN< VDD –10 — 10 µA Input Current If Pullup is Activated IINP VIL = 0 V 1 — 10 µA LL3 — 6.66 — mA DRV[1:0] = LH 3 — 5.03 — mA IOmaxHL DRV[1:0] = HL 3 — 3.16 — mA IOmaxHH DRV[1:0] = HH3 — 1.13 — mA IOmaxLL 3 — 5.75 — mA 3 — 4.37 — mA IOmaxHL DRV[1:0] = HL3 — 2.73 — mA IOmaxHH DRV[1:0] = HH3 — 0.96 — mA IOmaxLL 3 — 2.53 — mA LH3 — 2.21 — mA IOmaxHL DRV[1:0] = HL 3 — 1.7 — mA IOmaxHH DRV[1:0] = HH3 — 0.80 — mA Logic High Level Output Voltage VOH DRV[1:0] = HL VDD x 0.8 — — V Logic Low Level Output Voltage VOL DRV[1:0] = HL — — VDD x 0.2 V Drive Strength for Output Low Level Drive Strength for Output High Level Drive Strength for Output High Level for GPIO0 IOmaxLL IOmaxLH IOmaxLH IOmaxLH DRV[1:0] = DRV[1:0] = LL DRV[1:0] = LH DRV[1:0] = LL DRV[1:0] = Notes: 1. All specifications guaranteed by qualification. Qualification test conditions are listed in the "Qualification Test Conditions" section in "1.1. Definition of Test Conditions" on page 14. 2. 8 ns is typical for GPIO0 rise time. 3. Assuming VDD = 3.3 V, drive strength is specified at Voh (min) = 2.64 V and Vol(max) = 0.66 V at room temperature. 4. 2.4 ns is typical for GPIO0 fall time. 12 Rev 1.2 Si4464/63/61/60 Table 7. Absolute Maximum Ratings Parameter Value Unit VDD to GND –0.3, +3.6 V Instantaneous VRF-peak to GND on TX Output Pin –0.3, +8.0 V Sustained VRF-peak to GND on TX Output Pin –0.3, +6.5 V Voltage on Digital Control Inputs –0.3, VDD + 0.3 V Voltage on Analog Inputs –0.3, VDD + 0.3 V +10 dBm –40 to +85 C Thermal Impedance JA 30 C/W Junction Temperature TJ +125 C –55 to +125 C RX Input Power Operating Ambient Temperature Range TA Storage Temperature Range TSTG Note: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only and functional operation of the device at or beyond these ratings in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Power Amplifier may be damaged if switched on without proper load or termination connected. TX matching network design will influence TX VRF-peak on TX output pin. Caution: ESD sensitive device. Rev 1.2 13 Si4464/63/61/60 1.1. Definition of Test Conditions Production Test Conditions: TA = +25 °C. VDD = +3.3 VDC. TX output power measured at 915 MHz. External reference signal (XOUT) = 1.0 VPP at 30 MHz, centered around 0.8 VDC. Production test schematic (unless noted otherwise). TX output levels are referred to the pins of the Si4464/63/61/60 (not the output of the RF module). All RX input levels are referred to the input of a tuned balun connected to the RX input pins of the Si4464/63/61/60. Qualification Test Conditions: All TA = –40 to +85 °C (Typical TA = 25 °C). VDD = +1.8 to +3.6 VDC (Typical VDD = 3.3 VDC). Using All 14 TX/RX Split Antenna reference design or production test schematic. RF input and output levels referred to the pins of the Si4464/63/61/60 (not the RF module). Rev 1.2 Si4464/63/61/60 2. Functional Description The Si446x devices are high-performance, low-current, wireless ISM transceivers that cover the sub-GHz bands. The wide operating voltage range of 1.8–3.6 V and low current consumption make the Si446x an ideal solution for battery powered applications. The Si446x operates as a time division duplexing (TDD) transceiver where the device alternately transmits and receives data packets. The device uses a single-conversion mixer to downconvert the 2/4-level FSK/GFSK or OOK modulated receive signal to a low IF frequency. Following a programmable gain amplifier (PGA) the signal is converted to the digital domain by a high performance ADC allowing filtering, demodulation, slicing, and packet handling to be performed in the built-in DSP increasing the receiver’s performance and flexibility versus analog based architectures. The demodulated signal is output to the system MCU through a programmable GPIO or via the standard SPI bus by reading the 64-byte RX FIFO. A single high precision local oscillator (LO) is used for both transmit and receive modes since the transmitter and receiver do not operate at the same time. The LO is generated by an integrated VCO and Fractional-N PLL synthesizer. The synthesizer is designed to support configurable data rates from 100 bps to 1 Mbps. The Si4463/61/60 operate in the frequency bands of 142–175, 283–350, 420–525, and 850–1050 MHz with a maximum frequency accuracy step size of 28.6 Hz. The Si4464 offers frequency coverage in bands not supported by Si4463/61/60. The transmit FSK data is modulated directly into the data stream and can be shaped by a Gaussian low-pass filter to reduce unwanted spectral content. The Si4464/63 contains a power amplifier (PA) that supports output power up to +20 dBm with very high efficiency, consuming only 70 mA at 169 MHz and 85 mA at 915 MHz. The integrated +20 dBm power amplifier can also be used to compensate for the reduced performance of a lower cost, lower performance antenna or antenna with size constraints due to a small form-factor. Competing solutions require large and expensive external PAs to achieve comparable performance. The Si4461 supplies output power up to +16 dBm. The Si4460 is designed to support single coin cell operation with current consumption below 18 mA for +10 dBm output power. Two match topologies are available for the Si4461 and Si4460, class-E and switched-current. Class-E matching provides optimal current consumption, while switched-current matching demonstrates the best performance over varying battery voltage and temperature with slightly higher current consumption. The PA is single-ended to allow for easy antenna matching and low BOM cost. The PA incorporates automatic ramp-up and ramp-down control to reduce unwanted spectral spreading. The Si446x family supports frequency hopping, TX/RX switch control, and antenna diversity switch control to extend the link range and improve performance. Built-in antenna diversity and support for frequency hopping can be used to further extend range and enhance performance. Antenna diversity is completely integrated into the Si446x and can improve the system link budget by 8–10 dB, resulting in substantial range increases under adverse environmental conditions. A highly configurable packet handler allows for autonomous encoding/decoding of nearly any packet structure. Additional system features, such as an automatic wake-up timer, low battery detector, 64 byte TX/RX FIFOs, and preamble detection, reduce overall current consumption and allows for the use of lower-cost system MCUs. An integrated temperature sensor, power-on-reset (POR), and GPIOs further reduce overall system cost and size. The Si446x is designed to work with an MCU, crystal, and a few passive components to create a very low-cost system. The application shown in Figure 1 is designed for a system with a TX/RX direct-tie configuration without the use of a TX/RX switch. Most applications with output power less than 17 dBm will use this configuration. Figure 2 demonstrates an application for +20 dBm using an external T/R-switch. Rev 1.2 15 Si4464/63/61/60 RXn XOUT GND 14 Si4461 13 4 NC C1 C3 2 5 6 VDD L1 12 7 11 10 9 8 nSEL SDI GP1 GP2 SDO GP3 SCLK GP4 nIRQ GP5 GPIO1 C4 C5 16 15 3 TX 17 GPIO0 L2 18 VDD L3 L4 L5 19 TXRAMP C2 RXp 1 Microcontroller 20 SDN XIN C6 GPIO2 GPIO3 30 MHz VDD C7 C8 C9 100 p 100 n 1u Figure 1. Si4461 Direct-Tie Application Example C4 TX NC C1 C3 C2 L1 XOUT GND XIN 16 15 2 14 Si4463 3 13 12 4 5 6 7 8 9 11 10 nSEL SDI GP1 GP2 SDO GP3 SCLK GP4 nIRQ GP5 VDD Figure 2. Si4463 Single Antenna with RF Switch Example 16 Rev 1.2 Microcontroller C5 L2 17 GPIO1 L3 RXn 18 GPIO0 L4 RXp L5 19 VDD C6 20 1 TXRAMP SDN VDD C7 GPIO2 GPIO3 30 MHz Si4464/63/61/60 3. Controller Interface 3.1. Serial Peripheral Interface (SPI) The Si446x communicates with the host MCU over a standard 4-wire serial peripheral interface (SPI): SCLK, SDI, SDO, and nSEL. The SPI interface is designed to operate at a maximum of 10 MHz. The SPI timing parameters are demonstrated in Table 8. The host MCU writes data over the SDI pin and can read data from the device on the SDO output pin. Figure 3 demonstrates an SPI write command. The nSEL pin should go low to initiate the SPI command. The first byte of SDI data will be one of the firmware commands followed by n bytes of parameter data which will be variable depending on the specific command. The rising edges of SCLK should be aligned with the center of the SDI data. Table 8. Serial Interface Timing Parameters Symbol Parameter Min (ns) tCH Clock high time 40 tCL Clock low time 40 tDS Data setup time 20 tDH Data hold time 20 tDD Output data delay time 20 tEN Output enable time 20 tDE Output disable time 50 tSS Select setup time 20 tSH Select hold time 50 tSW Select high period 80 Diagram SCLK tSS tCL tCH tDS tDH tDD tSH tDE SDI SDO tEN tSW nSEL nSEL SDO SDI FW Command Param Byte 0 Param Byte n SCLK Figure 3. SPI Write Command The Si446x contains an internal MCU which controls all the internal functions of the radio. For SPI read commands a typical MCU flow of checking clear-to-send (CTS) is used to make sure the internal MCU has executed the command and prepared the data to be output over the SDO pin. Figure 4 demonstrates the general flow of an SPI read command. Once the CTS value reads FFh then the read data is ready to be clocked out to the host MCU. The typical time for a valid FFh CTS reading is 20 µs. Figure 5 demonstrates the remaining read cycle after CTS is set to FFh. The internal MCU will clock out the SDO data on the negative edge so the host MCU should process the SDO data on the rising edge of SCLK. Rev 1.2 17 Si4464/63/61/60 Firmware Flow 0xFF Send Command Read CTS CTS Value Retrieve Response 0x00 NSEL CTS SDO SDI ReadCmdBuff SCK Figure 4. SPI Read Command—Check CTS Value NSEL SDO Response Byte 0 Response Byte n SDI SCK Figure 5. SPI Read Command—Clock Out Read Data 18 Rev 1.2 Si4464/63/61/60 3.2. Fast Response Registers The fast response registers are registers that can be read immediately without the requirement to monitor and check CTS. There are four fast response registers that can be programmed for a specific function. The fast response registers can be read through API commands, 0x50 for Fast Response A, 0x51 for Fast Response B, 0x53 for Fast Response C, and 0x57 for Fast Response D. The fast response registers can be configured by the “FRR_CTL_X_MODE” properties. The fast response registers may be read in a burst fashion. After the initial 16 clock cycles, each additional eight clock cycles will clock out the contents of the next fast response register in a circular fashion. The value of the FRRs will not be updated unless NSEL is toggled. 3.3. Operating Modes and Timing The primary states of the Si446x are shown in Figure 6. The shutdown state completely shuts down the radio to minimize current consumption. Standby/Sleep, SPI Active, Ready, TX Tune, and RX tune are available to optimize the current consumption and response time to RX/TX for a given application. API commands START_RX, START_TX, and CHANGE_STATE control the operating state with the exception of shutdown which is controlled by SDN, pin 1. Table 9 shows each of the operating modes with the time required to reach either RX or TX mode as well as the current consumption of each mode. The times in Table 9 are measured from the rising edge of nSEL until the chip is in the desired state. Note that these times are indicative of state transition timing but are not guaranteed and should only be used as a reference data point. An automatic sequencer will put the chip into RX or TX from any state. It is not necessary to manually step through the states. To simplify the diagram it is not shown but any of the lower power states can be returned to automatically after RX or TX. Figure 6. State Machine Diagram Rev 1.2 19 Si4464/63/61/60 Table 9. Operating State Response Time and Current Consumption* Response Time to TX RX Current in State /Mode Shutdown State 15 ms 15 ms 30 nA Standby State Sleep State SPI Active State Ready State TX Tune State RX Tune State 440 µs 440 µs 340 µs 126 µs 58 µs — 440 µs 440 µs 340 µs 122 µs — 74 µs 50 nA 900 nA 1.35 mA 1.8 mA 8 mA 7.2 mA TX State — 138 µs 18 mA @ +10 dBm RX State 130 µs 75 µs 10 or 13 mA State/Mode *Note: TXRX and RXTX state transition timing can be reduced to 70 µs if using Zero-IF mode. Figure 7 shows the POR timing and voltage requirements. The power consumption (battery life) depends on the duty cycle of the application or how often the part is in either Rx or Tx state. In most applications the utilization of the standby state will be most advantageous for battery life but for very low duty cycle applications shutdown will have an advantage. For the fastest timing the next state can be selected in the START_RX or START_TX API commands to minimize SPI transactions and internal MCU processing. 3.3.1. Power on Reset (POR) A Power On Reset (POR) sequence is used to boot the device up from a fully off or shutdown state. To execute this process, VDD must ramp within 1ms and must remain applied to the device for at least 10ms. If VDD is removed, then it must stay below 0.15V for at least 10ms before being applied again. Please see Figure x and Table x for details. VDD VR RH VR RL Time tSR tPORH Figure 7. POR Timing Diagram 20 Rev 1.2 Si4464/63/61/60 Table 10. POR Timing Variable tPORH Description High time for VDD to fully settle POR circuit tPORL Low time for VDD to enable POR VRRH Voltage for successful POR VRRL Starting Voltage for successful POR tSR Min Typ Max Units 10 ms 10 ms 90%*Vdd V 0 Slew rate of VDD for successful POR 150 mV 1 ms 3.3.2. Shutdown State The shutdown state is the lowest current consumption state of the device with nominally less than 30 nA of current consumption. The shutdown state may be entered by driving the SDN pin (Pin 1) high. The SDN pin should be held low in all states except the shutdown state. In the shutdown state, the contents of the registers are lost and there is no SPI access. When coming out of the shutdown state a power on reset (POR) will be initiated along with the internal calibrations. After the POR the POWER_UP command is required to initialize the radio. The SDN pin needs to be held high for at least 10us before driving low again so that internal capacitors can discharge. Not holding the SDN high for this period of time may cause the POR to be missed and the device to boot up incorrectly. If POR timing and voltage requirements cannot be met, it is highly recommended that SDN be controlled using the host processor rather than tying it to GND on the board. 3.3.3. Standby State Standby state has the lowest current consumption with the exception of shutdown but has much faster response time to RX or TX mode. In most cases standby should be used as the low power state. In this state the register values are maintained with all other blocks disabled. The SPI is accessible during this mode but any SPI event, including FIFO R/W, will enable an internal boot oscillator and automatically move the part to SPI active state. After an SPI event the host will need to re-command the device back to standby through the “Change State” API command to achieve the 50 nA current consumption. If an interrupt has occurred (i.e., the nIRQ pin = 0) the interrupt registers must be read to achieve the minimum current consumption of this mode. 3.3.4. Sleep State Sleep state is the same as standby state but the wake-up-timer and a 32 kHz clock source are enabled. The source of the 32 kHz clock can either be an internal 32 kHz RC oscillator which is periodically calibrated or a 32 kHz oscillator using an external XTAL.The SPI is accessible during this mode but an SPI event will enable an internal boot oscillator and automatically move the part to SPI active mode. After an SPI event the host will need to re-command the device back to sleep. If an interrupt has occurred (i.e., the nIRQ pin = 0) the interrupt registers must be read to achieve the minimum current consumption of this mode. 3.3.5. SPI Active State In SPI active state the SPI and a boot up oscillator are enabled. After SPI transactions during either standby or sleep the device will not automatically return to these states. A “Change State” API command will be required to return to either the standby or sleep modes. 3.3.6. Ready State Ready state is designed to give a fast transition time to TX or RX state with reasonable current consumption. In this mode the Crystal oscillator remains enabled reducing the time required to switch to TX or RX mode by eliminating the crystal start-up time. 3.3.7. TX State The TX state may be entered from any of the state with the “Start TX” or “Change State” API commands. A built-in sequencer takes care of all the actions required to transition between states from enabling the crystal oscillator to ramping up the PA. The following sequence of events will occur automatically when going from standby to TX state. 1. Enable internal LDOs. 2. Start up crystal oscillator and wait until ready (controlled by an internal timer). Rev 1.2 21 Si4464/63/61/60 3. Enable PLL. 4. Calibrate VCO/PLL. 5. Wait until PLL settles to required transmit frequency (controlled by an internal timer). 6. Activate power amplifier and wait until power ramping is completed (controlled by an internal timer). 7. Transmit packet. Steps in this sequence may be eliminated depending on which state the chip is configured to prior to commanding to TX. By default, the VCO and PLL are calibrated every time the PLL is enabled. When the START_TX API command is utilized the next state may be defined to ensure optimal timing and turnaround. Figure 8 shows an example of the commands and timing for the START_TX command. CTS will go high as soon as the sequencer puts the part into TX state. As the sequencer is stepping through the events listed above, CTS will be low and no new commands or property changes are allowed. If the Fast Response (FRR) or nIRQ is used to monitor the current state there will be slight delay caused by the internal hardware from when the event actually occurs to when the transition occurs on the FRR or nIRQ. The time from entering TX state to when the FRR will update is 5 µs and the time to when the nIRQ will transition is 13 µs. If a GPIO is programmed for TX state or used as control for a transmit/receive switch (TR switch) there is no delay. CTS NSEL SDI START_TX Current State FRR YYY State Tx State YYY State TXCOMPLETE_STATE Tx State TXCOMPLETE_STATE nIRQ GPIOx – TX state Figure 8. Start_TX Commands and Timing 3.3.8. RX State The RX state may be entered from any of the other states by using the “Start RX” or “Change State” API command. A built-in sequencer takes care of all the actions required to transition between states. The following sequence of events will occur automatically to get the chip into RX mode when going from standby to RX state: 1. Enable the digital LDO and the analog LDOs. 2. Start up crystal oscillator and wait until ready (controlled by an internal timer). 3. Enable PLL. 4. Calibrate VCO 5. Wait until PLL settles to required receive frequency (controlled by an internal timer). 6. Enable receiver circuits: LNA, mixers, and ADC. 7. Enable receive mode in the digital modem. Depending on the configuration of the radio, all or some of the following functions will be performed automatically by the digital modem: AGC, AFC (optional), update status registers, bit synchronization, packet handling (optional) including sync word, header check, and CRC. Similar to the TX state, the next state after RX may be defined in the “Start RX” API command. The START_RX commands and timing will be equivalent to the timing shown in Figure 8. 22 Rev 1.2 Si4464/63/61/60 3.4. Application Programming Interface (API) An application programming interface (API), which the host MCU will communicate with, is embedded inside the device. The API is divided into two sections, commands and properties. The commands are used to control the chip and retrieve its status. The properties are general configurations which will change infrequently. The API descriptions can be found in“AN625: Si446x API Descriptions”. 3.5. Interrupts The Si446x is capable of generating an interrupt signal when certain events occur. The chip notifies the microcontroller that an interrupt event has occurred by setting the nIRQ output pin LOW = 0. This interrupt signal will be generated when any one (or more) of the interrupt events (corresponding to the Interrupt Status bits) occur. The nIRQ pin will remain low until the microcontroller reads the Interrupt Status Registers. The nIRQ output signal will then be reset until the next change in status is detected. The interrupts sources are grouped into three groups: packet handler, chip status, and modem. The individual interrupts in these groups can be enabled/disabled in the interrupt property registers, 0101, 0102, and 0103. An interrupt must be enabled for it to trigger an event on the nIRQ pin. The interrupt group must be enabled as well as the individual interrupts in API property 0100. Number Command Summary 0x20 GET_INT_STATUS Returns the interrupt status—packet handler, modem, and chip 0x21 GET_PH_STATUS Returns the packet handler status. 0x22 GET_MODEM_STATUS 0x23 GET_CHIP_STATUS Returns the modem status byte. Returns the chip status. Number Property Default Summary 0x0100 INT_CTL_ENABLE 0x04 Enables interrupt groups for PH, Modem, and Chip. 0x0101 INT_CTL_PH_ENABLE 0x00 Packet handler interrupt enable property. 0x0102 INT_CTL_MODEM_ENABLE 0x00 Modem interrupt enable property. 0x0103 INT_CTL_CHIP_ENABLE 0x04 Chip interrupt enable property. Once an interrupt event occurs and the nIRQ pin is low there are two ways to read and clear the interrupts. All of the interrupts may be read and cleared in the “GET_INT_STATUS” API command. By default all interrupts will be cleared once read. If only specific interrupts want to be read in the fastest possible method the individual interrupt groups (Packet Handler, Chip Status, Modem) may be read and cleared by the “GET_MODEM_STATUS”, “GET_PH_STATUS” (packet handler), and “GET_CHIP_STATUS” API commands. The instantaneous status of a specific function maybe read if the specific interrupt is enabled or disabled. The status results are provided after the interrupts and can be read with the same commands as the interrupts. The status bits will give the current state of the function whether the interrupt is enabled or not. The fast response registers can also give information about the interrupt groups but reading the fast response registers will not clear the interrupt and reset the nIRQ pin. Rev 1.2 23 Si4464/63/61/60 3.6. GPIO Four general purpose IO pins are available to utilize in the application. The GPIO are configured by the GPIO_PIN_CFG command in address 13h. For a complete list of the GPIO options please see the API guide. GPIO pins 0 and 1 should be used for active signals such as data or clock. GPIO pins 2 and 3 have more susceptibility to generating spurious in the synthesizer than pins 0 and 1. The drive strength of the GPIOs can be adjusted with the GEN_CONFIG parameter in the GPIO_PIN_CFG command. By default the drive strength is set to minimum. The default configuration for the GPIOs and the state during SDN is shown below in Table 11.The state of the IO during shutdown is also shown inTable 11. As indicated previously in Table 6, GPIO 0 has lower drive strength than the other GPIOs. Table 11. GPIOs 24 Pin SDN State POR Default GPIO0 0 POR GPIO1 0 CTS GPIO2 0 POR GPIO3 0 POR nIRQ resistive VDD pull-up nIRQ SDO resistive VDD pull-up SDO SDI High Z SDI Rev 1.2 Si4464/63/61/60 4. Modulation and Hardware Configuration Options The Si446x supports different modulation options and can be used in various configurations to tailor the device to any specific application or legacy system for drop in replacement. The modulation and configuration options are set in API property, MODEM_MOD_TYPE. 4.1. MODEM_MOD_TYPE Summary: Modulation Type Purpose: This property selects between OOK, FSK, 4FSK and GFSK modulation, modulation source, and tx direct mode control. The modulator must be configured for one mode through the entire packet. If portions of the packet alternate between FSK and 4FSK modes, the modem should be programmed to 4FSK mode. Property: Default: 0x2000 0x02 Fields: TX_DIRECT_MODE_TYPE - default:0 0 = Direct mode operates in synchronous mode, applies to TX only. 1 = Direct mode operates in asynchronous mode, applies to TX only. GFSK is not supported. TX_DIRECT_MODE_GPIO[1:0] - default:0x0 0 = TX direct mode uses gpio0 as data source, applies to TX only. 1 = TX direct mode uses gpio1 as data source, applies to TX only. 2 = TX direct mode uses gpio2 as data source, applies to TX only. 3 = TX direct mode uses gpio3 as data source, applies to TX only. MOD_SOURCE[1:0] - default:0x0 0 = Modulation source is packet handler fifo 1 = Modulation source is direct mode pin 2 = Modulation source is pseudo-random generator MOD_TYPE[2:0] - default:0x2 0 = CW 1 = OOK 2 = 2FSK 3 = 2GFSK 4 = 4FSK 5 = 4GFSK Register View MODEM_MOD_TYPE 7 6 5 4 3 TX_DIRECT_MODE_TYPE TX_DIRECT_MODE_GPIO[1:0] MOD_SOURCE[1:0] 0 0x0 0x0 Rev 1.2 2 1 0 MOD_TYPE[2:0] 0x2 25 Si4464/63/61/60 4.2. Modulation Types The Si446x supports five different modulation options: Gaussian frequency shift keying (GFSK), frequency-shift keying (FSK), four-level GFSK (4GFSK), four-level FSK (4FSK), and on-off keying (OOK). Minimum shift keying (MSK) can also be created by using GFSK settings. GFSK is the recommended modulation type as it provides the best performance and cleanest modulation spectrum. The modulation type is set by the “MOD_TYPE[2:0]” registers in the “MODEM_MOD_TYPE” API property. A continuous-wave (CW) carrier may also be selected for RF evaluation purposes. The modulation source may also be selected to be a pseudo-random source for evaluation purposes. 4.3. Hardware Configuration Options There are different receive demodulator options to optimize the performance and mutually-exclusive options for how the RX/TX data is transferred from the host MCU to the RF device. 4.3.1. Receive Demodulator Options There are multiple demodulators integrated into the device to optimize the performance for different applications, modulation formats, and packet structures. The calculator built into WDS will choose the optimal demodulator based on the input criteria. 4.3.1.1. Synchronous Demodulator The synchronous demodulator's internal frequency error estimator acquires the frequency error based on a 101010 preamble structure. The bit clock recovery circuit locks to the incoming data stream within four transactions of a “10” or “01” bit stream. The synchronous demodulator gives optimal performance for 2- or 4-level FSK or GFSK modulation that has a modulation index less than 2. 4.3.1.2. Asynchronous Demodulator The asynchronous demodulator should be used OOK modulation and for FSK/GFSK/4GFSK under one or more of the following conditions: Modulation index > 2 Non-standard preamble (not 1010101... pattern) When the modulation index exceeds 2, the asynchronous demodulator has better sensitivity compared to the synchronous demodulator. An internal deglitch circuit provides a glitch-free data output and a data clock signal to simplify the interface to the host. There is no requirement to perform deglitching in the host MCU. The asynchronous demodulator will typically be utilized for legacy systems and will have many performance benefits over devices used in legacy designs. Unlike the Si4432/31 solution for non-standard packet structures, there is no requirement to perform deglitching on the data in the host MCU. Glitch-free data is output from Si446x devices, and a sample clock for the asynchronous data can also be supplied to the host MCU; so, oversampling or bit clock recovery is not required by the host MCU. There are multiple detector options in the asynchronous demodulator block, which will be selected based upon the options entered into the WDS calculator. The asynchronous demodulator's internal frequency error estimator is able to acquire the frequency error based on any preamble structure. 4.3.2. RX/TX Data Interface With MCU There are two different options for transferring the data from the RF device to the host MCU. FIFO mode uses the SPI interface to transfer the data, while direct mode transfers the data in real time over GPIO. 4.3.2.1. FIFO Mode In FIFO mode, the transmit and receive data is stored in integrated FIFO register memory. The TX FIFO is accessed by writing Command 66h followed directly by the data/clk that the host wants to write into the TX FIFO. The RX FIFO is accessed by writing command 77h followed by the number of clock cycles of data the host would like to read out of the RX FIFO. The RX data will be clocked out onto the SDO pin. In TX mode, if the packet handler is enabled, the data bytes stored in FIFO memory are “packaged” together with other fields and bytes of information to construct the final transmit packet structure. These other potential fields include the Preamble, Sync word, Header, CRC checksum, etc. The configuration of the packet structure in TX mode is determined by the Automatic Packet Handler (if enabled), in conjunction with a variety of Packet Handler properties. If the Automatic Packet Handler is disabled, the entire desired packet structure should be loaded into FIFO memory; no other fields (such as Preamble or Sync word) will be automatically added to the bytes stored in 26 Rev 1.2 Si4464/63/61/60 FIFO memory. For further information on the configuration of the FIFOs for a specific application or packet size, see "6. Data Handling and Packet Handler" on page 39. In RX mode, only the bytes of the received packet structure that are considered to be “data bytes” are stored in FIFO memory. Which bytes of the received packet are considered “data bytes” is determined by the Automatic Packet Handler (if enabled) in conjunction with the Packet Handler configuration. If the Automatic Packet Handler is disabled, all bytes following the Sync word are considered data bytes and are stored in FIFO memory. Thus, even if Automatic Packet Handling operation is not desired, the preamble detection threshold and Sync word still need to be programmed so that the RX Modem knows when to start filling data into the FIFO. When the FIFO is being used in RX mode, all of the received data may still be observed directly (in realtime) by properly programming a GPIO pin as the RXDATA output pin; this can be quite useful during application development. When in FIFO mode, the chip will automatically exit the TX or RX State when either the PACKET_SENT or PACKET_RX interrupt occurs. The chip will return to the IDLE state programmed in the argument of the “START TX” or “START RX” API command, TXCOMPLETE_STATE[3:0] or RXVALID_STATE[3:0]. For example, the chip may be placed into TX mode by sending the “START TX” command and by writing the 30h to the TXCOMPLETE_STATE[3:0] argument. The chip will transmit all of the contents of the FIFO, and the ipksent interrupt will occur. When this event occurs, the chip will return to the ready state as defined by TXCOMPLETE_STATE[3:0] = 30h. 4.3.2.2. Direct Mode For legacy systems that perform packet handling within the host MCU or other baseband chip, it may not be desirable to use the FIFO. For this scenario, a Direct mode is provided, which bypasses the FIFOs entirely. In TX Direct mode, the TX modulation data is applied to an input pin of the chip and processed in “real time” (i.e., not stored in a register for transmission at a later time). Any of the GPIOs may be configured for use as the TX Data input function. Furthermore, an additional pin may be required for a TX Clock output function if GFSK modulation is desired (only the TX Data input pin is required for FSK). To achieve direct mode, the GPIO must be configured in the “GPIO_PIN_CFG” API command as well as the “MODEM_MOD_TYPE” API property. For GFSK, “TX_DIRECT_MODE_TYPE” must be set to Synchronous. For 2FSK or OOK, the type can be set to asynchronous or synchronous. The MOD_SOURCE[1:0] should be set to 01h for are all direct mode configurations. In RX Direct mode, the RX Data and RX Clock can be programmed for direct (real-time) output to GPIO pins. The microcontroller may then process the RX data without using the FIFO or packet handler functions of the RFIC. 4.4. Preamble Length The preamble length requirement is only relevant if using the synchronous demodulator. If the asynchronous demodulator is being used, then there is no requirement for a conventional 101010 pattern. The preamble detection threshold determines the number of valid preamble bits the radio must receive to qualify a valid preamble. The preamble threshold should be adjusted depending on the nature of the application. The required preamble length threshold depends on when receive mode is entered in relation to the start of the transmitted packet and the length of the transmit preamble. With a shorter than recommended preamble detection threshold, the probability of false detection is directly related to how long the receiver operates on noise before the transmit preamble is received. False detection on noise may cause the actual packet to be missed. The preamble detection threshold may be adjusted in the modem calculator by modifying the “PM detection threshold” in the “RX parameters tab” in the radio control panel. For most applications with a preamble length longer than 32 bits, the default value of 20 is recommended for the preamble detection threshold. A shorter Preamble Detection Threshold may be chosen if occasional false detections may be tolerated. When antenna diversity is enabled, a 20- bit preamble detection threshold is recommended. When the receiver is synchronously enabled just before the start of the packet, a shorter preamble detection threshold may be used. Table 12 demonstrates the recommended preamble detection threshold and preamble length for various modes. Rev 1.2 27 Si4464/63/61/60 Table 12. Recommended Preamble Length Mode AFC Antenna Diversity Preamble Type Recommended Preamble Length Recommended Preamble Detection Threshold (G)FSK Disabled Disabled Standard 4 Bytes 20 bits (G)FSK Enabled Disabled Standard 5 Bytes 20 bits (G)FSK Disabled Disabled Non-standard 2 Bytes 0 bits (G)FSK Enabled (G)FSK Disabled Enabled Standard 7 Bytes 24 bits (G)FSK Enabled Enabled Standard 8 Bytes 24 bits 4(G)FSK Disabled Disabled Standard 40 symbols 16 symbols 4(G)FSK Enabled Disabled Standard 48 symbols 16 symbols Non-standard 4(G)FSK Not Supported Non-standard Not Supported OOK Disabled Disabled Standard 4 Bytes 20 bits OOK Disabled Disabled Non-standard 2 Bytes 0 bits OOK Enabled Not Supported Notes: 1. The recommended preamble length and preamble detection thresholds listed above are to achieve 0% PER. They may be shortened when occasional packet errors are tolerable. 2. All recommended preamble lengths and detection thresholds include AGC and BCR settling times. 3. “Standard” preamble type should be set for an alternating data sequence at the max data rate (…10101010…) 4. “Non-standard” preamble type can be set for any preamble type including …10101010... 5. When preamble detection threshold = 0, sync word needs to be 3 Bytes to avoid false syncs. When only a 2 Byte sync word is available the sync word detection can be extended by including the last preamble Byte into the RX sync word setting. 28 Rev 1.2 Si4464/63/61/60 5. Internal Functional Blocks The following sections provide an overview to the key internal blocks and features. 5.1. RX Chain The internal low-noise amplifier (LNA) is designed to be a wide-band LNA that can be matched with three external discrete components to cover any common range of frequencies in the sub-GHz band. The LNA has extremely low noise to suppress the noise of the following stages and achieve optimal sensitivity; so, no external gain or front-end modules are necessary. The LNA has gain control, which is controlled by the internal automatic gain control (AGC) algorithm. The LNA is followed by an I-Q mixer, filter, programmable gain amplifier (PGA), and ADC. The I-Q mixers downconvert the signal to an intermediate frequency. The PGA then boosts the gain to be within dynamic range of the ADC. The ADC rejects out-of-band blockers and converts the signal to the digital domain where filtering, demodulation, and processing is performed. Peak detectors are integrated at the output of the LNA and PGA for use in the AGC algorithm. The RX and TX pins maybe directly tied externally for output powers less than +17 dBm, see the direct-tie reference designs on the Silicon Labs web site for more details. 5.1.1. RX Chain Architecture It is possible to operate the RX chain in different architecture configurations: fixed-IF, zero-IF, scaled-IF, and modulated IF. There are trade-offs between the architectures in terms of sensitivity, selectivity, and image rejection. Fixed-IF is the default configuration and is recommended for most applications. With 35 dB native image rejection and autonomous image calibration to achieve 55 dB, the fixed-IF solution gives the best performance for most applications. Fixed-IF obtains the best sensitivity, but it has the effect of degraded selectivity at the image frequency. An autonomous image rejection calibration is included in Si446x devices and described in more detail in "5.2.3. Image Rejection and Calibration" on page 31. For fixed-IF and zero-IF, the sensitivity is degraded for data rates less than 100 kbps or bandwidths less than 200 kHz. The reduction in sensitivity is caused by increased flicker noise as dc is approached. The benefit of zero-IF is that there is no image frequency; so, there is no degradation in the selectivity curve, but it has the worst sensitivity. Scaled-IF is a trade-off between fixed-IF and zero-IF. In the scaled-IF architecture, the image frequency is placed or hidden in the adjacent channel where it only slightly degrades the typical adjacent channel selectivity. The scaled-IF approach has better sensitivity than zero-IF but still some degradation in selectivity due to the image. In scaled-IF mode, the image frequency is directly proportional to the channel bandwidth selected. Figure 9 demonstrates the trade-off in sensitivity between the different architecture options. 1% PER sensitivity vs. data rate (h=1) -95 Sensitivity (dBm) -100 -105 Fixed IF Scaled IF -110 Zero IF -115 -120 1 10 100 Data rate (kbps) Figure 9. RX Architecture vs. Data Rate Rev 1.2 29 Si4464/63/61/60 5.2. RX Modem Using high-performance ADCs allows channel filtering, image rejection, and demodulation to be performed in the digital domain, which allows for flexibility in optimizing the device for particular applications. The digital modem performs the following functions: Channel selection filter TX modulation RX demodulation Automatic Gain Control (AGC) Preamble detection Invalid preamble detection Radio signal strength indicator (RSSI) Automatic frequency compensation (AFC) Image Rejection Calibration handling including EZMAC® features Cyclic redundancy check (CRC) The digital channel filter and demodulator are optimized for ultra-low-power consumption and are highly configurable. Supported modulation types are GFSK, FSK, 4GFSK, 4FSK, GMSK, and OOK. The channel filter can be configured to support bandwidths ranging from 850 down to 1.1 kHz. A large variety of data rates are supported ranging from 100 bps up to 1 Mbps. The configurable preamble detector is used with the synchronous demodulator to improve the reliability of the sync-word detection. Preamble detection can be skipped using only sync detection, which is a valuable feature of the asynchronous demodulator when very short preambles are used in protocols, such as MBus. The received signal strength indicator (RSSI) provides a measure of the signal strength received on the tuned channel. The resolution of the RSSI is 0.5 dB. This high-resolution RSSI enables accurate channel power measurements for clear channel assessment (CCA), carrier sense (CS), and listen before talk (LBT) functionality. A comprehensive programmable packet handler including key features of Silicon Labs’ EZMAC is integrated to create a variety of communication topologies ranging from peer-to-peer networks to mesh networks. The extensive programmability of the packet header allows for advanced packet filtering, which, in turn enables a mix of broadcast, group, and point-to-point communication. A wireless communication channel can be corrupted by noise and interference, so it is important to know if the received data is free of errors. A cyclic redundancy check (CRC) is used to detect the presence of erroneous bits in each packet. A CRC is computed and appended at the end of each transmitted packet and verified by the receiver to confirm that no errors have occurred. The packet handler and CRC can significantly reduce the load on the system microcontroller allowing for a simpler and cheaper microcontroller. The digital modem includes the TX modulator, which converts the TX data bits into the corresponding stream of digital modulation values to be summed with the fractional input to the sigma-delta modulator. This modulation approach results in highly accurate resolution of the frequency deviation. A Gaussian filter is implemented to support GFSK and 4GFSK, considerably reducing the energy in adjacent channels. The default bandwidth-time product (BT) is 0.5 for all programmed data rates, but it may be adjusted to other values. Packet 5.2.1. Automatic Gain Control (AGC) The AGC algorithm is implemented digitally using an advanced control loop optimized for fast response time. The AGC occurs within a single bit or in less than 2 µs. Peak detectors at the output of the LNA and PGA allow for optimal adjustment of the LNA gain and PGA gain to optimize IM3, selectivity, and sensitivity performance. 5.2.2. Auto Frequency Correction (AFC) Frequency mistuning caused by crystal inaccuracies can be compensated for by enabling the digital automatic frequency control (AFC) in receive mode. There are two types of integrated frequency compensation: modem frequency compensation, and AFC by adjusting the PLL frequency. With AFC disabled, the modem compensation can correct for frequency offsets up to ±0.25 times the IF bandwidth. When the AFC is enabled, the received signal will be centered in the pass-band of the IF filter, providing optimal sensitivity and selectivity over a wider range of frequency offsets up to ±0.35 times the IF bandwidth. When AFC is enabled, the preamble length needs to be long enough to settle the AFC. As shown in Table 12 on page 28, an additional byte of preamble is typically required to settle the AFC. 30 Rev 1.2 Si4464/63/61/60 5.2.3. Image Rejection and Calibration Since the receiver utilizes a low-IF architecture, the selectivity will be affected by the image frequency. The IF frequency is 468.75 kHz (Fxtal/64), and the image frequency will be at 937.5 kHz below the RF frequency. The native image rejection of the Si446x family is 35 dB. Image rejection calibration is available in the Si446x to improve the image rejection to more than 55 dB. The calibration is initiated with the IRCAL API command. The calibration uses an internal signal source, so no external signal generator is required. The initial calibration takes 250 ms, and periodic re-calibration takes 100 ms. Re-calibration should be initiated when the temperature has changed more than 30 °C. 5.2.4. Received Signal Strength Indicator The received signal strength indicator (RSSI) is an estimate of the signal strength in the channel to which the receiver is tuned. The RSSI measurement is done after the channel filter, so it is only a measurement of the desired or undesired in-band signal power. There are two different methods for reading the RSSI value and several different options for configuring the RSSI value that is returned. The fastest method for reading the RSSI is to configure one of the four fast response registers (FRR) to return a latched RSSI value. The latched RSSI value is measured once per packet and is latched at a configurable amount of time after RX mode is entered. The fast response registers can be read in 16 SPI clock cycles with no requirement to wait for CTS. The RSSI value may also be read out of the GET_MODEM_STATUS command. In this command, both the current RSSI and the latched RSSI are available. The current RSSI value represents the signal strength at the instant in time the GET_MODEM_STATUS command is processed and may be read multiple times per packet. Reading the RSSI in the GET_MODEM_STATUS command takes longer than reading the RSSI out of the fast response register. After the initial command, it will take 33 μs for CTS to be set and then the four or five bytes of SPI clock cycles to read out the respective current or latched RSSI values. The RSSI configuration options are set in the MODEM_RSSI_CONTROL API property. The latched RSSI value may be latched and stored based on the following events: preamble detection, sync detection, or a configurable number of bit times measured after the start of RX mode (minimum of 4 bit times). The requirement for four bit times is determined by the processing delay and settling through the modem and digital channel filter. In MODEM_RSSI_CONTROL, the RSSI may be defined to update every bit period or to be averaged and updated every four bit periods. If RSSI averaging over four bits is enabled, the latched RSSI value will be delayed to a minimum of 7 bits after the start of RX mode to allow for the averaging. The latched RSSI values are cleared when entering RX mode so they may be read after the packet is received or after dropping back to standby mode. If the RSSI value has been cleared by the start of RX but not latched yet, a value of 0 will be returned if it is attempted to be read. The RSSI value read by the API could be translated to dBm by the following linear equation: RSSI (in dBm) = (RSSI_value /2) – RSSIcal RSSIcal in the above formula depends on the matching network, modem settings, and external LNA gain (if present). The RSSIcal value can be obtained by a simple calibration with a signal generator connected at the antenna input. Without external LNA, the value of RSSIcal is around 130 ±30. During packet reception, it may be useful to detect whether a secondary interfering signal (desired or undesired) arrives. To detect this event, a feature for RSSI jump detection is available. If the RSSI level changes by a programmable amount during the reception of a packet, an interrupt or GPIO can be configured to notify the host. The level of RSSI increase or decrease (jump) is programmable through the MODEM_RSSI_JUMP_THRESH API property. If an RSSI jump is detected, the modem may be programmed to automatically reset so that it may lock onto the new stronger signal. The chip may also be configured to automatically reset the receiver upon jump detection in order to acquire the new signal. The configuration and options for RSSI jump detection are programmed in the MODEM_RSSI_CONTROL2 API property. By default, RSSI jump detection is not enabled. Rev 1.2 31 Si4464/63/61/60 The RSSI values and curves may be offset by the MODEM_RSSI_COMP API property. The default value of 7’h32 corresponds to no RSSI offset. Setting a value less than 7’h32 corresponds to a negative offset, and a value higher than 7’h32 corresponds to a positive offset. The offset value is in 1 dB steps. For example, setting a value of 7’h3A corresponds to a positive offset of 8 dB. Clear channel assessment (CCA) or RSSI threshold detection is also available. An RSSI threshold may be set in the MODEM_RSSI_THRESH API property. If the RSSI value is above this threshold, an interrupt or GPIO may notify the host. Both the latched version and asynchronous version of this threshold are available on any of the GPIOs. Automatic fast hopping based on RSSI is available. See “5.3.1.2. Automatic RX Hopping and Hop Table”. 5.3. Synthesizer An integrated Sigma Delta () Fractional-N PLL synthesizer capable of operating over the bands from 142–175, 283–350, 420–525, and 850–1050 MHz for the Si4460/61/63. The Si4464 offers frequency coverage in bands that are not covered by Si4463/1/0. Using a synthesizer has many advantages; it provides flexibility in choosing data rate, deviation, channel frequency, and channel spacing. The transmit modulation is applied directly to the loop in the digital domain through the fractional divider, which results in very precise accuracy and control over the transmit deviation. The frequency resolution in the 850–1050 MHz band is 28.6 Hz with more resolution in the other bands. The nominal reference frequency to the PLL is 30 MHz, but any XTAL frequency from 25 to 32 MHz may be used. The modem configuration calculator in WDS will automatically account for the XTAL frequency being used. The PLL utilizes a differential LC VCO with integrated on-chip inductors. The output of the VCO is followed by a configurable divider, which will divide the signal down to the desired output frequency band. 5.3.1. Synthesizer Frequency Control The frequency is set by changing the integer and fractional settings to the synthesizer. The WDS calculator will automatically provide these settings, but the synthesizer equation is shown below for convenience. The APIs for setting the frequency are FREQ_CONTROL_INTE, FREQ_CONTROL_FRAC2, FREQ_CONTROL_FRAC1, and FREQ_CONTROL_FRAC0. freq_xo fc_frac- 2 ----------------------------- Hz RF_channel = fc_inte + ----------------19 outdiv 2 Note: The fc_frac/219 value in the above formula has to be a number between 1 and 2. Table 13. Output Divider (Outdiv) Values for the Si4460/61/63 Outdiv Lower (MHz) Upper (MHz) 24 142 175 12 284 350 8 420 525 4 850 1050 Table 14. Output Divider (Outdiv) for the Si4464 32 Outdiv Lower (MHz) Upper (MHz) 24 119 159 16 177 239 12 235 319 8 353 479 6 470 639 4 705 960 Rev 1.2 Si4464/63/61/60 5.3.1.1. EZ Frequency Programming In applications that utilize multiple frequencies or channels, it may not be desirable to write four API registers each time a frequency change is required. EZ frequency programming is provided so that only a single register write (channel number) is required to change frequency. A base frequency is first set by first programming the integer and fractional components of the synthesizer. This base frequency will correspond to channel 0. Next, a channel step size is programmed into the FREQ_CONTROL_CHANNEL_STEP_SIZE_1 and FREQ_CONTROL_CHANNEL_STEP_SIZE_0 API registers. The resulting frequency will be: RF Frequency = Base Frequency + Channel Stepsi ze The second argument of the START_RX or START_TX is CHANNEL, which sets the channel number for EZ frequency programming. For example, if the channel step size is set to 1 MHz, the base frequency is set to 900 MHz with the INTE and FRAC API registers, and a CHANNEL number of 5 is programmed during the START_TX command, the resulting frequency will be 905 MHz. If no CHANNEL argument is written as part of the START_RX/TX command, it will default to the previous value. The initial value of CHANNEL is 0; so, if no CHANNEL value is written, it will result in the programmed base frequency. 5.3.1.2. Automatic RX Hopping and Hop Table The transceiver supports an automatic hopping feature that can be fully configured through the API. This is intended for RX hopping where the device has to hop from channel to channel and look for packets. Once the device is put into the RX state, it automatically starts hopping through the hop table if the feature is enabled. The hop table can hold up to 64 entries and is maintained in firmware. Each entry is a channel number; so, the hop table can hold up to 64 channels. The number of entries in the table is set by RX HOP TABLE_SIZE API. The specified channels correspond to the EZ frequency programming method for programming the frequency. The receiver starts at the base channel and hops in sequence from the top of the hop table to the bottom. The table will wrap around to the base channel once it reaches the end of the table. An entry of 0xFF in the table indicates that the entry should be skipped. The device will hop to the next non 0xFF entry. There are three conditions that can be used to determine whether to continue hopping or to stay on a particular channel. These conditions are: RSSI threshold Preamble timeout (invalid preamble pattern) Sync word timeout (invalid or no sync word detected after preamble) These conditions can be used individually, or they can be enabled all together by configuring the RX_HOP_CONTROL API. However, the firmware will make a decision on whether or not to hop based on the first condition that is met. The RSSI that is monitored is the current RSSI value. This is compared to the threshold, and, if it is above the threshold value, it will stay on the channel. If the RSSI is below the threshold, it will continue hopping. There is no averaging of RSSI done during the automatic hopping from channel to channel. Since the preamble timeout and the sync word timeout are features that require packet handling, the RSSI threshold is the only condition that can be used if the user is in “direct” or “RAW” mode where packet handling features are not used. Note that the RSSI threshold is not an absolute RSSI value; instead, it is a relative value and should be verified on the bench to find an optimal threshold for the application. The turnaround time from RX to RX on a different channel using this method is 115 µs. The time spent in receive mode will be determined by the configuration of the hop conditions. Manual RX hopping will have the fastest turn-around time but will require more overhead and management by the host MCU. The following are example steps for using Auto Hop: 1. Set the base frequency (inte + frac) and channel step size. 2. Define the number of entries in the hop table (RX_HOP_TABLE_SIZE). 3. Write the channels to the hop table (RX_HOP_TABLE_ENTRY_n) 4. Configure the hop condition and enable auto hopping- RSSI, preamble, or sync (RX_HOP_CONTROL). 5. Set preamble and sync parameters if enabled. Rev 1.2 33 Si4464/63/61/60 6. Program the RSSI threshold property in the modem using “MODEM_RSSI_THRESH”. 7. Set the preamble threshold using “PREAMBLE_CONFIG_STD_1”. 8. Program the preamble timeout property using “PREAMBLE_CONFIG_STD_2”. 9. Set the sync detection parameters if enabled. 10. If needed, use “GPIO_PIN_CFG” to configure a GPIO to toggle on hop and hop table wrap. 11. Use the “START_RX” API with channel number set to the first valid entry in the hop table (i.e., the first non 0xFF entry). 12. Device should now be in auto hop mode. 5.3.1.3. Manual RX Hopping The RX_HOP command provides the fastest method for hopping from RX to RX but it requires more overhead and management by the host MCU. Using the RX_HOP command, the turn-around time is 75 µs. The timing is faster with this method than Start_RX or RX hopping because one of the calculations required for the synthesizer calibrations is offloaded to the host and must be calculated/stored by the host, VCO_CNT0. For information about using fast manual hopping, contact customer support. 5.4. Transmitter (TX) The Si4464/63 contains an integrated +20 dBm transmitter or power amplifier that is capable of transmitting from –20 to +20 dBm. The output power steps are less than 0.25 dB within 6 dB of max power but become larger and more non-linear close to minimum output power. The Si4464/63 PA is designed to provide the highest efficiency and lowest current consumption possible. The Si4461 PA is capable of transmitting from –40 to +16 dBm. The Si4461 PA can be optimized for either optimum current consumption (Class E) or for fine output power steps and performance over voltage and temperature (switched-current). Switched-current matching will have fine output power steps and more constant output power over VDD, but it will have higher current consumption than the class-E matching. The class E will have the most efficient current consumption, but it will have more coarse output power steps and variation across VDD. The Si4460 is designed to supply +10 dBm output power for less than 20 mA for applications that require operation from a single coin cell battery. The Si4460 can also operate with either class-E or switched current matching and output up to +13 dBm Tx power. All PA options are single-ended to allow for easy antenna matching and low BOM cost. Automatic ramp-up and ramp-down is automatically performed to reduce unwanted spectral spreading. Chip’s TXRAMP pin is disabled by default to save current in cases where on-chip PA will be able to drive the antenna. In cases where on-chip PA will drive the external PA, and the external PA needs a ramping signal, TXRAMP is the signal to use. To enable TXRAMP, set the API Property PA_MODE[7] = 1. TXRAMP will start to ramp up, and ramp down at the SAME time as the internal on-chip PA ramps up/down. The ramping speed is programmed by TC[3:0] in the PA_RAMP_EX API property, which has the following characteristics: 34 TC Ramp Time (µs) 0.0 2.0 1.0 2.1 2.0 2.2 3.0 2.4 4.0 2.6 5.0 2.8 6.0 3.1 7.0 3.4 8.0 3.7 Rev 1.2 Si4464/63/61/60 9.0 4.1 10.0 4.5 11.0 5.0 12.0 6.0 13.0 8.0 14.0 10.0 15.0 20.0 The ramping profile is close to a linear ramping profile with smoothed out corner when approaching Vhi and Vlo. The TXRAMP pin can source up to 1 mA without voltage drooping. The TXRAMP pin’s sinking capability is equivalent to a 10 k pull-down resistor. Vhi = 3 V when Vdd > 3.3 V. When Vdd < 3.3 V, the Vhi will be closely following the Vdd, and ramping time will be smaller also. Vlo = 0 V when NO current needed to be sunk into TXRAMP pin. If 10uA need to be sunk into the chip, Vlo will be 10 µA x 10k = 100 mV. Number Command Summary 0x2200 PA_MODE 0x2201 PA_PWR_LVL 0x2202 PA_BIAS_CLKDUTY Adjust TX power in coarse steps and optimizes for different match configurations. 0x2203 PA_TC Changes the ramp up/down time of the PA. Sets PA type. Adjust TX power in fine steps. 5.4.1. Si4464/63: +20 dBm PA The +20 dBm configuration utilizes a class-E matching configuration. Typical performance for the 900 MHz band for output power steps, voltage, and temperature are shown in Figures 10–12. The output power is changed in 128 steps through PA_PWR_LVL API. For detailed matching values, BOM, and performance at other frequencies, refer to the PA Matching application note. TX Power(dBm) TX Power vs. PA_PWR_LVL 25 20 15 10 5 0 -5 -10 -15 -20 -25 -30 -35 0 10 20 30 40 50 60 70 80 90 100 110 120 PA_PWR_LVL Figure 10. +20 dBm TX Power vs. PA_PWR_LVL Rev 1.2 35 Si4464/63/61/60 TX Power vs. VDD TX Power (dBm) 22 20 18 16 14 12 10 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 Supply Voltage (VDD) Figure 11. +20 dBm TX Power vs. VDD TX Power vs Temp TX Power (dBm) 20.5 20 19.5 19 18.5 18 -40 -30 -20 -10 0 10 20 30 40 50 60 Temperature (C) Figure 12. +20 dBm TX Power vs. Temp 36 Rev 1.2 70 80 Si4464/63/61/60 5.4.2. Si4461 +16 dBm PA The Si4461 PA can utilize different matches to optimize the performance for 16, 14, 13 dBm, or a lower power. A class-E match is recommended for 16 dBm to maximize the efficiency and battery life. For 13 and 14 dBm, a switched current match is recommended to provide optimal performance over VDD and temperature variation. Typical performance for the 900 MHz band for output power steps, voltage, and temperature are shown in Figures 13 and 14. The output power is changed in 128 steps through the PA_PWR_LVL API. For detailed matching values, BOM, and performance at other frequencies, refer to “AN627: Si4460/61 Low-Power PA Matching. Figure 13. +13 dBm TX Power vs. PA_PWR_LVL Figure 14. +13 dBm TX Power vs. Supply Voltage (VDD) Rev 1.2 37 Si4464/63/61/60 5.5. Crystal Oscillator The Si446x includes an integrated crystal oscillator with a fast start-up time of less than 250 µs. The design is differential with the required crystal load capacitance integrated on-chip to minimize the number of external components. By default, all that is required off-chip is the crystal. The default crystal is 30 MHz, but the circuit is designed to handle any XTAL from 25 to 32 MHz. If a crystal different than 30 MHz is used, the POWER_UP API boot command must be modified. The WDS calculator crystal frequency field must also be changed to reflect the frequency being used. The crystal load capacitance can be digitally programmed to accommodate crystals with various load capacitance requirements and to adjust the frequency of the crystal oscillator. The tuning of the crystal load capacitance is programmed through the GLOBAL_XO_TUNE API property. The total internal capacitance is 11 pF and is adjustable in 127 steps (70 fF/step). The crystal frequency adjustment can be used to compensate for crystal production tolerances. The frequency offset characteristics of the capacitor bank are demonstrated in Figure 15. Figure 15. Capacitor Bank Frequency Offset Characteristics Utilizing the on-chip temperature sensor and suitable control software, the temperature dependency of the crystal can be canceled. A TCXO or external signal source can easily be used in place of a conventional XTAL and should be connected to the XIN pin. The incoming clock signal is recommended to have a peak-to-peak swing in the range of 600 mV to 1.4 V and ac-coupled to the XIN pin. If the peak-to-peak swing of the TCXO exceeds 1.4 V peak-to-peak, then dc coupling to the XIN pin should be used. The maximum allowed swing on XIN is 1.8 V peak-to-peak. The XO capacitor bank should be set to 0 whenever an external drive is used on the XIN pin. In addition, the POWER_UP command should be invoked with the TCXO option whenever external drive is used. 38 Rev 1.2 Si4464/63/61/60 6. Data Handling and Packet Handler 6.1. RX and TX FIFOs Two 64-byte FIFOs are integrated into the chip, one for RX and one for TX, as shown in Figure 16. Writing to command Register 66h loads data into the TX FIFO, and reading from command Register 77h reads data from the RX FIFO. The TX FIFO has a threshold for when the FIFO is almost empty, which is set by the “TX_FIFO_EMPTY” property. An interrupt event occurs when the data in the TX FIFO reaches the almost empty threshold. If more data is not loaded into the FIFO, the chip automatically exits the TX state after the PACKET_SENT interrupt occurs. The RX FIFO has one programmable threshold, which is programmed by setting the “RX_FIFO_FULL” property. When the incoming RX data crosses the Almost Full Threshold, an interrupt will be generated to the microcontroller via the nIRQ pin. The microcontroller will then need to read the data from the RX FIFO. The RX Almost Full Threshold indication implies that the host can read at least the threshold number of bytes from the RX FIFO at that time. Both the TX and RX FIFOs may be cleared or reset with the “FIFO_RESET” command. RX FIFO TX FIFO RX FIFO Almost Full Threshold TX FIFO Almost Empty Threshold Figure 16. TX and RX FIFOs 6.2. Packet Handler Config 0, 2, o r 4 Bytes Con fig 0, 2, o r 4 Bytes Con fig 0, 2, o r 4 B ytes C RC Field 5 (op t) Field 5 (opt) Data C RC Field 4 (op t) Field 4 (opt) Data C RC Field 3 (op t) Field 3 (opt) Data Con fig C RC Field 2 (op t) 1-4 Bytes F ield 2 (o pt) Pkt Len gth or Data Field 1 Header or Data 1-255 Bytes C RC Field 1 (op t) Preamble Sync Word When using the FIFOs, automatic packet handling may be enabled for TX mode, RX mode, or both. The usual fields for network communication, such as preamble, synchronization word, headers, packet length, and CRC, can be configured to be automatically added to the data payload. The fields needed for packet generation normally change infrequently and can therefore be stored in registers. Automatically adding these fields to the data payload in TX mode and automatically checking them in RX mode greatly reduces the amount of communication between the microcontroller and Si446x. It also greatly reduces the required computational power of the microcontroller. The general packet structure is shown in Figure 17. Any or all of the fields can be enabled and checked by the internal packet handler. Con fig 0, 2, or 4 Bytes 0, 2, or 4 Bytes Figure 17. Packet Handler Structure Rev 1.2 39 Si4464/63/61/60 The fields are highly programmable and can be used to check any kind of pattern in a packet structure. The general functions of the packet handler include the following: Detection/validation of Preamble quality in RX mode (PREAMBLE_VALID signal) of Sync word in RX mode (SYNC_OK signal) Detection of valid packets in RX mode (PKT_VALID signal) Detection of CRC errors in RX mode (CRC_ERR signal) Data de-whitening and/or Manchester decoding (if enabled) in RX mode Match/Header checking in RX mode Storage of Data Field bytes into FIFO memory in RX mode Construction of Preamble field in TX mode Construction of Sync field in TX mode Construction of Data Field from FIFO memory in TX mode Construction of CRC field (if enabled) in TX mode Data whitening and/or Manchester encoding (if enabled) in TX mode For details on how to configure the packet handler, see “AN626: Packet Handler Operation for Si446x RFICs”. Detection 40 Rev 1.2 Si4464/63/61/60 7. RX Modem Configuration The Si446x can easily be configured for different data rate, deviation, frequency, etc. by using the WDS settings calculator, which generates an initialization file for use by the host MCU. 8. Auxiliary Blocks 8.1. Wake-up Timer and 32 kHz Clock Source The chip contains an integrated wake-up timer that can be used to periodically wake the chip from sleep mode. The wake-up timer runs from either the internal 32 kHz RC Oscillator, or from an external 32 kHz XTAL. The wake-up timer can be configured to run when in sleep mode. If WUT_EN = 1 in the GLOBAL_WUT_CONFIG property, prior to entering sleep mode, the wake-up timer will count for a time specified defined by the GLOBAL_WUT_R and GLOBAL_WUT_M properties. At the expiration of this period, an interrupt will be generated on the nIRQ pin if this interrupt is enabled in the INT_CTL_CHIP_ENABLE property. The microcontroller will then need to verify the interrupt by reading the chip interrupt status either via GET_INT_STATUS or a fast response register. The formula for calculating the Wake-Up Period is as follows: WUT_R 42 WUT = WUT_M ----------------------------- ms 32 768 The RC oscillator frequency will change with temperature; so, a periodic recalibration is required. The RC oscillator is automatically calibrated during the POWER_UP command and exits from the Shutdown state. To enable the recalibration feature, CAL_EN must be set in the GLOBAL_WUT_CONFIG property, and the desired calibration period should be selected via WUT_CAL_PERIOD[2:0] in the same API property. During the calibration, the 32 kHz RC oscillator frequency is compared to the 30 MHz XTAL and then adjusted accordingly. The calibration needs to start the 30 MHz XTAL, which increases the average current consumption; so, a longer CAL_PERIOD results in a lower average current consumption. The 32 kHz XTAL accuracy is comprised of both the XTAL parameters and the internal circuit. The XTAL accuracy can be defined as the XTAL initial error + XTAL aging + XTAL temperature drift + detuning from the internal oscillator circuit. The error caused by the internal circuit is typically less than 10 ppm. Rev 1.2 41 Si4464/63/61/60 Table 15. WUT Specific Commands and Properties API Properties Description Requirements/Notes GLOBAL_WUT_CONFIG GLOBAL WUT configuration WUT_EN—Enable/disable wake up timer. WUT_LBD_EN—Enable/disable low battery detect measurement on WUT interval. WUT_LDC_EN: 0 = Disable low duty cycle operation. 1 = RX LDC operation treated as wake up START_RX WUT state is used 2 = TX LDC operation treated as wakeup START_TX WUT state is used CAL_EN—Enable calibration of the 32 kHz RC oscillator WUT_CAL_PERIOD[2:0]—Sets calibration period. GLOBAL_WUT_M_15_8 Sets HW WUT_M[15:8] WUT_M—Parameter to set the actual wakeup time. See equation above. GLOBAL_ WUT_M_7_0 Sets HW WUT_M[7:0] WUT_M—Parameter to set the actual wakeup time. See equation above. GLOBAL_WUT_R Sets WUT_R[4:0] Sets WUT_SLEEP to choose WUT state WUT_R—Parameter to set the actual wakeup time. See equation above. WUT_SLEEP: 0 = Go to ready state after WUT 1 = Go to sleep state after WUT GLOBAL_WUT_LDC Sets FW internal WUT_LDC WUT_LDC—Parameter to set the actual wakeup time. See equation in "8.2. Low Duty Cycle Mode (Auto RX Wake-Up)" on page 43. Table 16. WUT Related API Commands and Properties Command/Property Description Requirements/Notes WUT Interrupt Enable INT_CTL_ENABLE INT_CTL_CHIP_ENABLE Interrupt enable property CHIP_INT_STATUS_EN—Enables chip status interrupt. Chip interrupt enable property WUT_EN—Enables WUT interrupt. 32 kHz Clock Source Selection GLOBAL_CLK_CFG Clock configuration options CLK_32K_SEL[2:0]—Configuring the source of WUT. WUT Interrupt Output GPIO_PIN_CFG Host can enable interrupt on WUT expire GPIOx_MODE[5:0] = 14 and NIRQ_MODE[5:0] = 39. RX/TX Operation START_RX/TX 42 START RX/TX when wake up START = 1. timer expire Rev 1.2 Si4464/63/61/60 8.2. Low Duty Cycle Mode (Auto RX Wake-Up) The low duty cycle (LDC) mode is implemented to automatically wake-up the receiver to check if a valid signal is available or to enable the transmitter to send a packet. It allows low average current polling operation by the Si446x for which the wake-up timer (WUT) is used. RX and TX LDC operation must be set via the GLOBAL_WUT_CONFIG property when setting up the WUT. The LDC wake-up period is determined by the following formula: WUT_R 42 LDC = WUT_LDC ----------------------------- ms 32 768 where the WUT_LDC parameter can be set by the GLOBAL_WUT_LDC property. The WUT period must be set in conjunction with the LDC mode duration; for the relevant API properties, see the wake-up timer (WUT) section. Figure 18. RX and TX LDC Sequences The basic operation of RX LDC mode is shown in Figure 19. The receiver periodically wakes itself up to work on RX_STATE during LDC mode duration. If a valid preamble is not detected, a receive error is detected, or an entire packet is not received, the receiver returns to the WUT state (i.e., ready or sleep) at the end of LDC mode duration and remains in that mode until the beginning of the next wake-up period. If a valid preamble or sync word is detected, the receiver delays the LDC mode duration to receive the entire packet. If a packet is not received during two LDC mode durations, the receiver returns to the WUT state at the last LDC mode duration until the beginning of the next wake-up period. Figure 19. Low Duty Cycle Mode for RX In TX LDC mode, the transmitter periodically wakes itself up to transmit a packet that is in the data buffer. If a packet has been transmitted, nIRQ goes low if the option is set in the INT_CTL_ENABLE property. After transmitting, the transmitter immediately returns to the WUT state and stays there until the next wake-up time expires. Rev 1.2 43 Si4464/63/61/60 8.3. Temperature, Battery Voltage, and Auxiliary ADC The Si446x family contains an integrated auxiliary ADC for measuring internal battery voltage, an internal temperature sensor, or an external component over a GPIO. The ADC utilizes a SAR architecture and achieves 11-bit resolution. The Effective Number of Bits (ENOB) is 9 bits. When measuring external components, the input voltage range is 1 V, and the conversion rate is between 300 Hz to 2.44 kHz. The ADC value is read by first sending the GET_ADC_READING command and enabling the inputs that are desired to be read: GPIO, battery, or temp. The temperature sensor accuracy at 25 °C is typically ±2 °C. Command Stream GET_ADC_READING Command 7 6 5 4 3 CMD 2 1 0x14 ADC_EN 0 0 0 ADC_CFG Reply TEMPERATURE_EN BATTERY_VOLTAGE_EN ADC_GPIO_EN ADC_GPIO_PIN[1:0] UDTIME[3:0] GPIO_ATT[3:0] Stream GET_ADC_READING Reply 7 6 5 4 3 CTS CTS[7:0] GPIO_ADC GPIO_ADC[15:8] GPIO_ADC GPIO_ADC[7:0] BATTERY_ADC BATTERY_ADC[15:8] BATTERY_ADC BATTERY_ADC[7:0] TEMP_ADC TEMP_ADC[15:8] TEMP_ADC TEMP_ADC[7:0] RESERVED Reserved RESERVED Reserved 2 1 Parameters TEMPERATURE_EN 0 = Do not perform ADC conversion of temperature. This will read 0 value in reply TEMPERATURE. 1 = Perform ADC conversion of temperature. This results in TEMP_ADC. Temp (°C) = TEMP_ADC[15:0] x 568/2560 – 297 BATTERY_VOLTAGE_EN 0 = Don't do ADC conversion of battery voltage, will read 0 value in reply BATTERY_ADC 1 = Do ADC conversion of battery voltage, results in BATTERY_ADC. Vbatt = 3*BATTERY_ADC/1280 ADC_GPIO_EN 0 = Don't do ADC conversion on GPIO, will read 0 value in reply 1 = Do ADC conversion of GPIO, results in GPIO_ADC. Vgpio = GPIO_ADC/GPIO_ADC_DIV where GPIO_ADC_DIV is defined by GPIO_ATT selection. ADC_GPIO_PIN[1:0] - Select GPIOx pin. The pin must be set as input. 0 = Measure voltage of GPIO0 1 = Measure voltage of GPIO1 2 = Measure voltage of GPIO2 3 = Measure voltage of GPIO3 UDTIME[7:4] - ADC conversion Time = SYS_CLK / 12 / 2^(UDTIME + 1). Defaults to 0xC if ADC_CFG is 0. 44 0 Rev 1.2 0 Si4464/63/61/60 Selecting shorter conversion times will result in lower ADC resolution and longer times will result in higher ADC resolution. GPIO_ATT[3:0] - Sets attenuation of gpio input voltage when vgpio measured. Defaults to 0xC if ADC_CFG is 0. 0x0 = ADC range 0 to 0.8V. GPIO_ADC_DIV = 2560 0x4 = ADC range 0 to 1.6V. GPIO_ADC_DIV = 1280 0x8 = ADC range 0 to 2.4V. GPIO_ADC_DIV = 853.33 0x9 = ADC range 0 to 3.6V. GPIO_ADC_DIV = 426.66 0xC = ADC range 0 to 3.2V. GPIO_ADC_DIV = 640 Response GPIO_ADC[15:0] - ADC value of voltage on GPIO - ADC value of battery voltage TEMP_ADC[15:0] - ADC value of temperature sensor voltage RESERVED[7:0] - RESERVED FOR FUTURE USE RESERVED[7:0] - RESERVED FOR FUTURE USE BATTERY_ADC[15:0] 8.4. Low Battery Detector The low battery detector (LBD) is enabled and utilized as part of the wake-up-timer (WUT). The LBD function is not available unless the WUT is enabled, but the host MCU can manually check the battery voltage anytime with the auxiliary ADC. The LBD function is enabled in the GLOBAL_WUT_CONFIG API property. The battery voltage will be compared against the threshold each time the WUT expires. The threshold for the LBD function is set in GLOBAL_LOW_BATT_THRESH. The threshold steps are in increments of 50 mV, ranging from a minimum of 1.5 V up to 3.05 V. The accuracy of the LBD is ±3%. The LBD notification can be configured as an interrupt on the nIRQ pin or enabled as a direct function on one of the GPIOs. 8.5. Antenna Diversity To mitigate the problem of frequency-selective fading due to multipath propagation, some transceiver systems use a scheme known as antenna diversity. In this scheme, two antennas are used. Each time the transceiver enters RX mode the receive signal strength from each antenna is evaluated. This evaluation process takes place during the preamble portion of the packet. The antenna with the strongest received signal is then used for the remainder of that RX packet. The same antenna will also be used for the next corresponding TX packet. This chip fully supports antenna diversity with an integrated antenna diversity control algorithm. The required signals needed to control an external SPDT RF switch (such as a PIN diode or GaAs switch) are available on the GPIOx pins. The operation of these GPIO signals is programmable to allow for different antenna diversity architectures and configurations. The antdiv[2:0] bits are found in the MODEM_ANT_DIV_CONTROL API property descriptions and enable the antenna diversity mode. The GPIO pins are capable of sourcing up to 5 mA of current; so, it may be used directly to forward-bias a PIN diode if desired. The antenna diversity algorithm will automatically toggle back and forth between the antennas until the packet starts to arrive. The recommended preamble length for optimal antenna selection is 8 bytes. Rev 1.2 45 Si4464/63/61/60 SDN 1 XOUT XIN GND GPIO2 GPIO3 9. Pin Descriptions: Si4464/63/61/60 20 19 18 17 16 RXp 2 15 nSEL RXn 3 14 SDI GND PAD TX 4 13 SDO Pin Pin Name 7 8 9 VDD GPIO0 10 11 nIRQ GPIO1 6 TXRamp 12 SCLK VDD NC 5 I/0 Description 1 SDN I Shutdown Input Pin. 0–VDD V digital input. SDN should be = 0 in all modes except Shutdown mode. When SDN = 1, the chip will be completely shut down, and the contents of the registers will be lost. 2 RXp I Differential RF Input Pins of the LNA. 3 RXn I See application schematic for example matching network. 4 TX O 5 NC 6 VDD VDD 7 TXRAMP O 8 VDD VDD 9 GPIO0 I/O General Purpose Digital I/O. 10 GPIO1 I/O May be configured through the registers to perform various functions including: Microcontroller Clock Output, FIFO status, POR, Wake-Up timer, Low Battery Detect, TRSW, AntDiversity control, etc. Transmit Output Pin. The PA output is an open-drain connection, so the L-C match must supply VDD (+3.3 VDC nominal) to this pin. No Connect. Not connected internally to any circuitry. +1.8 to +3.6 V Supply Voltage Input to Internal Regulators. The recommended VDD supply voltage is +3.3 V. Programmable Bias Output with Ramp Capability for External FET PA. See "5.4. Transmitter (TX)" on page 34. +1.8 to +3.6 V Supply Voltage Input to Internal Regulators. The recommended VDD supply voltage is +3.3 V. General Microcontroller Interrupt Status Output. 11 46 nIRQ O When the Si4463/61 exhibits any one of the interrupt events, the nIRQ pin will be set low = 0. The Microcontroller can then determine the state of the interrupt by reading the interrupt status. No external resistor pull-up is required, but it may be desirable if multiple interrupt lines are connected. Rev 1.2 Si4464/63/61/60 Pin Pin Name I/0 Description Serial Clock Input. 12 SCLK I 13 SDO O 0–VDD V digital input. This pin provides the serial data clock function for the 4-line serial data bus. Data is clocked into the Si4463/61 on positive edge transitions. 0–VDD V Digital Output. Provides a serial readback function of the internal control registers. Serial Data Input. 14 SDI I 0–VDD V digital input. This pin provides the serial data stream for the 4-line serial data bus. Serial Interface Select Input. 15 nSEL I 0–VDD V digital input. This pin provides the Select/Enable function for the 4-line serial data bus. Crystal Oscillator Output. 16 XOUT O 17 XIN I 18 GND GND 19 GPIO2 I/O General Purpose Digital I/O. I/O May be configured through the registers to perform various functions, including Microcontroller Clock Output, FIFO status, POR, Wake-Up timer, Low Battery Detect, TRSW, AntDiversity control, etc. GND The exposed metal paddle on the bottom of the Si446x supplies the RF and circuit ground(s) for the entire chip. It is very important that a good solder connection is made between this exposed metal paddle and the ground plane of the PCB underlying the Si446x. 20 PKG GPIO3 PADDLE_GND Connect to an external 25 to 32 MHz crystal, or leave floating when driving with an external source on XIN. Crystal Oscillator Input. Connect to an external 25 to 32 MHz crystal, or connect to an external source. Connect to PCB ground. Rev 1.2 47 Si4464/63/61/60 10. Ordering Information Part Number1,2 Description Package Type Si4464-Bxx-FM ISM EZRadioPRO Transceiver QFN-20 Pb-free –40 to 85 °C Si4463-Bxx-FM ISM EZRadioPRO Transceiver QFN-20 Pb-free –40 to 85 °C Si4461-Bxx-FM ISM EZRadioPRO Transceiver QFN-20 Pb-free –40 to 85 °C Si4460-Bxx-FM ISM EZRadioPRO Transceiver QFN-20 Pb-free –40 to 85 °C Notes: 1. Add an “(R)” at the end of the device part number to denote tape and reel option. 2. For Bxx, the first “x” indicates the ROM version, and the second “x” indicates the FW version in OTP. 48 Operating Temperature Rev 1.2 Si4464/63/61/60 11. Package Outline: Si4464/63/61/60 Figure 20 illustrates the package details for the Si446x. Table 17 lists the values for the dimensions shown in the illustration. 2X bbb C B A D D2 Pin 1 (Laser) e 20 20x L 1 E E2 2X aaa C A1 20x b ccc C ddd C A B eee C A A3 SEATING PLANE C Figure 20. 20-Pin Quad Flat No-Lead (QFN) Rev 1.2 49 Si4464/63/61/60 Table 17. Package Dimensions Dimension Min Nom Max A 0.80 0.85 0.90 A1 0.00 0.02 0.05 A3 b 0.20 REF 0.18 0.25 D D2 0.30 4.00 BSC 2.45 2.60 e 0.50 BSC E 4.00 BSC 2.75 E2 2.45 2.60 2.75 L 0.30 0.40 0.50 aaa 0.15 bbb 0.15 ccc 0.10 ddd 0.10 eee 0.08 Notes: 1. All dimensions are shown in millimeters (mm) unless otherwise noted. 2. Dimensioning and tolerancing per ANSI Y14.5M-1994. 3. This drawing conforms to the JEDEC Solid State Outline MO-220, Variation VGGD-8. 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020C specification for Small Body Components. 50 Rev 1.2 Si4464/63/61/60 12. PCB Land Pattern: Si4464/63/61/60 Figure 21 illustrates the PCB land pattern details for the Si446x. Table 18 lists the values for the dimensions shown in the illustration. Figure 21. PCB Land Pattern Rev 1.2 51 Si4464/63/61/60 Table 18. PCB Land Pattern Dimensions Symbol Millimeters Min Max C1 3.90 4.00 C2 3.90 4.00 E 0.50 REF X1 0.20 0.30 X2 2.55 2.65 Y1 0.65 0.75 Y2 2.55 2.65 Notes: General 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. This land pattern design is based on IPC-7351 guidelines. Solder Mask Design 3. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 µm minimum, all the way around the pad. Stencil Design 4. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release. 5. The stencil thickness should be 0.125 mm (5 mils). 6. The ratio of stencil aperture to land pad size should be 1:1 for the perimeter pads. 7. A 2x2 array of 1.10 x 1.10 mm openings on 1.30 mm pitch should be used for the center ground pad. Card Assembly 8. A No-Clean, Type-3 solder paste is recommended. 9. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for small body components. 52 Rev 1.2 Si4464/63/61/60 13. Top Marking 13.1. Si4464/63/61/60 Top Marking 13.2. Top Marking Explanation Mark Method YAG Laser Line 1 Marking Part Number 44641B = Si4464 Rev 1B1 44631B = Si4463 Rev 1B1 44611B = Si4461 Rev 1B1 44601B = Si4460 Rev 1B1 Line 2 Marking TTTTT = Internal Code Internal tracking code.2 Line 3 Marking YY = Year WW = Workweek Assigned by the Assembly House. Corresponds to the last significant digit of the year and workweek of the mold date. Notes: 1. The first letter after the part number is part of the ROM revision. The last letter indicates the firmware revision. 2. The first letter of this line is part of the ROM revision. Rev 1.2 53 Si4464/63/61/60 DOCUMENT CHANGE LIST Revision 0.4 to Revision 1.0 Updated Table 3 on page 6. Updated Table 6 on page 12. Updated Figure 13 on page 37. Replaced Table 12 on page 28. Updated "11. Package Outline: Si4464/63/61/60" on page 49. Revision 1.0 to Revision 1.1 Updated RX Mode Current in Table 1 on page 4. Updated Synthesizer Frequency Range in Table 2 on page 5. Updated RX Frequency Range and RX Sensitivity in Table 3 on page 6. Updated TX Frequency Range in Table 4 on page 9. Updated Temperature Sensor Sensitivity in Table 5 on page 11. Updated Drive Strength in Table 6 on page 12. Updated Figure 1 and Figure 2 on page 16. Updated "3.2. Fast Response Registers" on page 19. Updated Table 9 on page 20. Updated Figure 9 on page 29. Updated "5.2.4. Received Signal Strength Indicator" on page 31. Updated "5.4. Transmitter (TX)" on page 34. Updated "8.3. Temperature, Battery Voltage, and Auxiliary ADC" on page 44. Updated "9. Pin Descriptions: Si4464/63/61/60" on page 46. Updated "11. Package Outline: Si4464/63/61/60" on page 49. Revision 1.1 to Revision 1.2 54 Updated all instances of frequency range for Si4463/61/60 and Si4464, primarily in the electrical specifications Tables. Removed emissions and harmonics specifications from the electrical specifications. Updated Tables 13 and 14 to reflect frequency coverage. Updated sections 5.2.3 and 5.2.4. Updated “13.1. Si4464/63/61/60 Top Marking”. Updated “9. Pin Descriptions: Si4464/63/61/60” for pins 16 and 17. Rev 1.2 Si4464/63/61/60 NOTES: Rev 1.2 55 Si4464/63/61/60 CONTACT INFORMATION Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 Tel: 1+(512) 416-8500 Fax: 1+(512) 416-9669 Toll Free: 1+(877) 444-3032 Please visit the Silicon Labs Technical Support web page: https://www.silabs.com/support/pages/contacttechnicalsupport.aspx and register to submit a technical support request. Patent Notice Silicon Labs invests in research and development to help our customers differentiate in the market with innovative low-power, small size, analog-intensive mixed-signal solutions. Silicon Labs' extensive patent portfolio is a testament to our unique approach and world-class engineering team. The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice. Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where personal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized application, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages. Silicon Laboratories and Silicon Labs are trademarks of Silicon Laboratories Inc. Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders. 56 Rev 1.2