20 V, 4 A, Synchronous, Step-Down DC-to-DC Regulator ADP2384 Data Sheet FEATURES TYPICAL APPLICATIONS CIRCUIT ADP2384 VIN BST PVIN CIN CBST EN VOUT PGOOD FB RT COMP VREG CVREG COUT RTOP SYNC RT L SW SS GND PGND RC CSS RBOT CC 10725-001 Input voltage: 4.5 V to 20 V Integrated MOSFET: 44 mΩ/11.6 mΩ Reference voltage: 0.6 V ± 1% Continuous output current: 4 A Programmable switching frequency: 200 kHz to 1.4 MHz Synchronizes to external clock: 200 kHz to 1.4 MHz 180° out-of-phase clock synchronization Precision enable and power good External compensation Internal soft start with external adjustable option Startup into a precharged output Supported by ADIsimPower design tool Figure 1. APPLICATIONS Communications infrastructure Networking and servers Industrial and instrumentation Healthcare and medical Intermediate power rail conversion DC-to-dc point-of-load applications GENERAL DESCRIPTION This regulator targets high performance applications that require high efficiency and design flexibility. External compensation and an adjustable soft start function provide design flexibility. The powergood output and precision enable input provide simple and reliable power sequencing. Rev. A The ADP2384 operates over the −40°C to +125°C junction temperature range and is available in a 24-lead, 4 mm × 4 mm LFCSP package. 100 95 90 85 80 75 70 65 60 VOUT = 1.2V VOUT = 3.3V VOUT = 5V 55 50 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 OUTPUT CURRENT (A) 10725-002 The ADP2384 requires minimal external components and operates from an input voltage of 4.5 V to 20 V. The output voltage can be adjusted from 0.6 V to 90% of the input voltage and delivers up to 4 A of continuous current. Each IC draws less than 120 μA current from the input source when it is disabled. Other key features include undervoltage lockout (UVLO), overvoltage protection (OVP), overcurrent protection (OCP), short-circuit protection (SCP), and thermal shutdown (TSD). EFFICIENCY (%) The ADP2384 is a synchronous, step-down dc-to-dc regulator with an integrated 44 mΩ, high-side power MOSFET and an 11.6 mΩ, synchronous rectifier MOSFET to provide a high efficiency solution in a compact 4 mm × 4 mm LFCSP package. This device uses a peak current mode, constant frequency pulsewidth modulation (PWM) control scheme for excellent stability and transient response. The switching frequency of the ADP2384 can be programmed from 200 kHz to 1.4 MHz. To minimize system noise, the synchronization function allows the switching frequency to be synchronized to an external clock. Figure 2. Efficiency vs. Output Current, VIN = 12 V, fSW = 300 kHz Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2012–2014 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADP2384 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Thermal Shutdown .................................................................... 14 Applications ....................................................................................... 1 Applications Information .............................................................. 15 Typical Applications Circuit............................................................ 1 Input Capacitor Selection .......................................................... 15 General Description ......................................................................... 1 Output Voltage Setting .............................................................. 15 Revision History ............................................................................... 2 Voltage Conversion Limitations ............................................... 15 Specifications..................................................................................... 3 Inductor Selection ...................................................................... 15 Absolute Maximum Ratings ............................................................ 5 Output Capacitor Selection....................................................... 16 Thermal Resistance ...................................................................... 5 Programming the Input Voltage UVLO.................................. 17 ESD Caution .................................................................................. 5 Compensation Design ............................................................... 17 Pin Configuration and Function Descriptions ............................. 6 ADIsimPower Design Tool ....................................................... 18 Typical Performance Characteristics ............................................. 7 Design Example .............................................................................. 19 Functional Block Diagram ............................................................ 11 Output Voltage Setting (Design Example) .............................. 19 Theory of Operation ...................................................................... 12 Frequency Setting ....................................................................... 19 Control Scheme .......................................................................... 12 Inductor Selection (Design Example) ..................................... 19 Precision Enable/Shutdown ...................................................... 12 Output Capacitor Selection (Design Example) ...................... 20 Internal Regulator (VREG) ....................................................... 12 Compensation Components ..................................................... 20 Bootstrap Circuitry .................................................................... 12 Soft Start Time Program ........................................................... 20 Oscillator ..................................................................................... 12 Input Capacitor Selection (Design Example) ......................... 20 Synchronization .......................................................................... 12 Recommended External Components .................................... 21 Soft Start ...................................................................................... 13 Circuit Board Layout Recommendations ................................... 22 Power Good ................................................................................. 13 Typical Applications Circuits ........................................................ 23 Peak Current-Limit and Short-Circuit Protection................. 13 Outline Dimensions ....................................................................... 24 Overvoltage Protection (OVP) ................................................. 14 Ordering Guide .......................................................................... 24 Undervoltage Lockout (UVLO) ............................................... 14 REVISION HISTORY 7/14—Rev. 0 to Rev. A Changes to Table 2 and Table 3 ....................................................... 5 Changes to Inductor Selection Section ........................................ 15 Changes to Compensation Components Section....................... 20 Updated Outline Dimensions ....................................................... 24 8/12—Revision 0: Initial Version Rev. A | Page 2 of 24 Data Sheet ADP2384 SPECIFICATIONS VPVIN = 12 V, TJ = −40°C to +125°C for minimum/maximum specifications, and TA = 25°C for typical specifications, unless otherwise noted. Table 1. Parameter PVIN PVIN Voltage Range Quiescent Current Shutdown Current PVIN Undervoltage Lockout Threshold Symbol VPVIN IQ ISHDN UVLO Test Conditions/Comments Min 4.5 2.1 45 Typ 2.9 80 4.3 3.8 Max Unit 20 3.6 120 4.5 V mA µA V V No switching EN = GND PVIN rising PVIN falling 3.5 0°C < TJ < 85°C −40°C < TJ < 125°C 0.594 0.591 0.6 0.6 0.01 0.606 0.609 0.1 V V µA 340 40 40 470 60 60 600 80 80 µS µA µA 7.6 8 340 100 8.4 135 V mV mA 44 11.6 70 20 mΩ mΩ 6.1 20 7.4 A mV 125 200 168 260 ns ns 4.5 5 5.5 V 530 200 600 670 1400 kHz kHz 1400 0.4 kHz ns ns V V 3.9 Clock cycles µA FB FB Regulation Voltage FB Bias Current ERROR AMPLIFIER (EA) Transconductance EA Source Current EA Sink Current INTERNAL REGULATOR (VREG) VREG Voltage Dropout Voltage Regulator Current Limit SW High-Side On Resistance 1 Low-Side On Resistance1 High-Side Peak Current Limit Low-Side Negative Current-Limit Threshold Voltage 2 SW Minimum On Time SW Minimum Off Time BST Bootstrap Voltage OSCILLATOR (RT PIN) Switching Frequency Switching Frequency Range SYNC Synchronization Range SYNC Minimum Pulse Width SYNC Minimum Off Time SYNC Input High Voltage SYNC Input Low Voltage SS Internal Soft Start SS Pin Pull-Up Current VFB IFB gm ISOURCE ISINK VVREG VPVIN = 12 V, IVREG = 50 mA VPVIN = 12 V, IVREG = 50 mA 65 VBST − VSW = 5 V VVREG = 8 V 4.8 tMIN_ON tMIN_OFF VBOOT fSW fSW RT = 100 kΩ 200 100 100 1.3 ISS_UP 2.5 Rev. A | Page 3 of 24 1600 3.2 ADP2384 Parameter PGOOD Power-Good Range FB Rising Threshold FB Rising Hysteresis FB Falling Threshold FB Falling Hysteresis Power-Good Deglitch Time Power-Good Leakage Current Power-Good Output Low Voltage EN EN Rising Threshold EN Falling Threshold EN Source Current Data Sheet Symbol Test Conditions/Comments PGOOD from low to high PGOOD from high to low PGOOD from low to high PGOOD from high to low PGOOD from low to high PGOOD from high to low VPGOOD = 5 V IPGOOD = 1 mA EN voltage below falling threshold EN voltage above rising threshold 2 Typ 95 5 105 11.7 1024 16 0.01 125 0.97 THERMAL SHUTDOWN Thermal Shutdown Threshold Thermal Shutdown Hysteresis 1 Min 1.17 1.07 5 1 150 25 Pin-to-pin measurement. Guaranteed by design. Rev. A | Page 4 of 24 Max Unit 0.1 200 % % % % Clock cycle Clock cycle µA mV 1.28 V V µA µA °C °C Data Sheet ADP2384 ABSOLUTE MAXIMUM RATINGS THERMAL RESISTANCE Table 2. Parameter PVIN, SW, EN, PGOOD SW 10 ns Transient SW 100 ns Transient BST FB, SS, COMP, SYNC, RT VREG PGND to GND Operating Junction Temperature Range Storage Temperature Range Soldering Conditions Rating −0.3 V to +22 V −2.5 V to +22 V −1 V to +22 V VSW + 6 V −0.3 V to +6 V −0.3 V to +12 V −0.3 V to +0.3 V −40°C to +125°C −65°C to +150°C JEDEC J-STD-020 θJA is specified for the worst-case conditions, that is, a device soldered in a 4-layer, JEDEC standard circuit board for surfacemount packages. Table 3. Thermal Resistance Package Type 24-Lead LFCSP_WQ ESD CAUTION Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Rev. A | Page 5 of 24 θJA 42.6 θJC 6.8 (EP, SW) 2.3 (EP, GND) Unit °C/W ADP2384 Data Sheet 19 PVIN 21 PGOOD 20 EN 22 RT 24 SS 23 SYNC PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 18 PVIN COMP 1 FB 2 17 PVIN 25 GND VREG 3 16 PVIN 15 BST GND 4 26 SW SW 5 14 SW SW 6 PGND 12 PGND 11 PGND 10 PGND 9 SW 7 PGND 8 13 PGND 10725-003 ADP2384 TOP VIEW NOTES 1. THE EXPOSED GND PAD MUST BE SOLDERED TO A LARGE, EXTERNAL, COPPER GND PLANE TO REDUCE THERMAL RESISTANCE. 2. THE EXPOSED SW PAD MUST BE CONNECTED TO THE SW PINS OF THE ADP2384 BY USING SHORT, WIDE TRACES, OR ELSE SOLDERED TO A LARGE, EXTERNAL, COPPER SW PLANE TO REDUCE THERMAL RESISTANCE. Figure 3. Pin Configuration Table 4. Pin Function Descriptions Pin No. 1 2 3 Mnemonic COMP FB VREG 4 5, 6, 7, 14 8, 9, 10, 11, 12, 13 15 16,17,18,19 20 GND SW PGND BST PVIN EN 21 22 PGOOD RT 23 SYNC 24 SS 25 26 EP, GND EP, SW Description Error Amplifier Output. Connect an RC network from COMP to GND. Feedback Voltage Sense Input. Connect to a resistor divider from the output voltage, VOUT. Output of the Internal 8 V Regulator. The control circuits are powered from this voltage. Place a 1 µF, X7R or X5R ceramic capacitor between this pin and GND. Analog Ground. Return of internal control circuit. Switch Node Output. Connect to the output inductor. Power Ground. Return of low-side power MOSFET. Supply Rail for the High-Side Gate Drive. Place a 0.1 µF, X7R or X5R capacitor between SW and BST. Power Input. Connect to the input power source and connect a bypass capacitor between this pin and PGND. Precision Enable Pin. An external resistor divider can be used to set the turn-on threshold. To enable the part automatically, connect the EN pin to the PVIN pin. Power-Good Output (Open Drain). A pull-up resistor of 10 kΩ to 100 kΩ is recommended. Frequency Setting. Connect a resistor between RT and GND to program the switching frequency from 200 kHz to 1.4 MHz. Synchronization Input. Connect this pin to an external clock to synchronize the switching frequency from 200 kHz and 1.4 MHz. See the Oscillator section and Synchronization section for more information. Soft Start Control. Connect a capacitor from SS to GND to program the soft start time. If this pin is open, the regulator uses the internal soft start time. The exposed GND pad must be soldered to a large, external, copper GND plane to reduce thermal resistance. The exposed SW pad must be connected to the SW pins of the ADP2384, using short, wide traces, or else soldered to a large, external, copper SW plane to reduce thermal resistance. Rev. A | Page 6 of 24 Data Sheet ADP2384 TYPICAL PERFORMANCE CHARACTERISTICS 100 100 95 95 90 90 85 85 EFFICIENCY (%) 80 75 70 65 80 75 70 65 INDUCTOR: FDVE1040-3R3M 55 50 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 OUTPUT CURRENT (A) INDUCTOR: FDVE1040-6R8M 50 10725-004 55 0 0.5 1.0 1.5 2.0 2.5 3.0 95 95 90 90 85 85 EFFICIENCY (%) 100 80 75 70 65 80 75 70 VOUT = 1.0V VOUT = 1.2V VOUT = 1.5V VOUT = 1.8V VOUT = 2.5V VOUT = 3.3V 65 VOUT = 1.8V VOUT = 2.5V VOUT = 3.3V VOUT = 5V INDUCTOR: FDVE1040-3R3M 60 55 50 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 OUTPUT CURRENT (A) INDUCTOR: FDVE1040-1R5M 50 10725-005 55 4.0 Figure 7. Efficiency at VIN = 12 V, fSW = 300 kHz 100 60 3.5 OUTPUT CURRENT (A) Figure 4. Efficiency at VIN = 12 V, fSW = 600 kHz EFFICIENCY (%) VOUT = 1.2V VOUT = 1.8V VOUT = 2.5V VOUT = 3.3V VOUT = 5V 60 10725-007 VOUT = 1.2V VOUT = 1.8V VOUT = 2.5V VOUT = 3.3V VOUT = 5V 60 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 OUTPUT CURRENT (A) 10725-008 EFFICIENCY (%) TA = 25°C, VIN = 12 V, VOUT = 3.3 V, L = 3.3 µH, COUT = 47 µF × 2, fSW = 600 kHz, unless otherwise noted. Figure 8. Efficiency at VIN = 5 V, fSW = 600 kHz Figure 5. Efficiency at VIN = 18 V, fSW = 600 kHz 100 3.2 3.0 70 60 TJ = –40°C TJ = +25°C TJ = +125°C 6 8 10 12 14 16 INPUT VOLTAGE (V) 18 2.6 2.4 2.2 TJ = –40°C TJ = +25°C TJ = +125°C 2.0 50 4 2.8 20 1.8 4 6 8 10 12 14 16 INPUT VOLTAGE (V) Figure 6. Shutdown Current vs. VIN Figure 9. Quiescent Current vs. VIN Rev. A | Page 7 of 24 18 20 10725-009 QUIESCENT CURRENT (mA) 80 10725-006 SHUTDOWN CURRENT (µA) 90 ADP2384 Data Sheet 1.25 4.5 4.4 1.20 EN THRESHOLD (V) PVIN UVLO THRESHOLD (V) RISING RISING 4.3 4.2 4.1 4.0 3.9 1.15 1.10 FALLING 1.05 FALLING 3.8 1.00 –20 0 20 40 60 80 100 120 TEMPERATURE (°C) 0.95 –40 10725-010 3.6 –40 –20 0 20 40 60 80 100 120 TEMPERATURE (°C) Figure 10. UVLO Threshold vs. Temperature 10725-013 3.7 Figure 13. EN Threshold vs. Temperature 3.30 606 3.25 FEEDBACK VOLTAGE (mV) SS PULL-UP CURRENT (µA) 604 3.20 3.15 3.10 3.05 3.00 602 600 598 596 –20 0 20 40 60 80 100 120 TEMPERATURE (°C) 594 –40 10725-011 20 40 60 80 100 120 100 120 Figure 14. FB Voltage vs. Temperature 8.4 630 8.3 VREG VOLTAGE (V) 620 610 RT = 100kΩ 600 590 580 8.2 8.1 8.0 7.9 7.8 –20 0 20 40 60 80 TEMPERATURE (°C) 100 120 7.7 –40 10725-012 FREQUENCY (kHz) 0 TEMPERATURE (°C) Figure 11. SS Pin Pull-Up Current vs. Temperature 570 –40 –20 –20 0 20 40 60 80 TEMPERATURE (°C) Figure 15. VREG Voltage vs. Temperature Figure 12. Frequency vs. Temperature Rev. A | Page 8 of 24 10725-015 2.90 –40 10725-014 2.95 Data Sheet ADP2384 7.0 PEAK CURRENT LIMIT THRESHOLD (A) 65 MOSFET RESISTOR (mΩ) HIGH-SIDE RDSON 45 35 25 5 –40 –20 0 20 40 60 80 100 6.0 5.5 5.0 4.5 4.0 –40 10725-016 LOW-SIDE RDSON 15 6.5 120 TEMPERATURE (°C) 20 0 –20 40 60 80 10725-019 55 120 100 TEMPERATURE (°C) Figure 16. MOSFET RDSON vs. Temperature Figure 19. Current-Limit Threshold vs. Temperature VOUT (AC) EN 3 1 IL VOUT 1 2 SW PGOOD 4 IOUT W CH2 10.0V CH4 2.00A Ω M2.00µs T 50.00% A CH2 5.00V 10725-017 B CH1 10mV CH1 2.00V CH3 10.0V Figure 17. Working Mode Waveform B W CH2 5.00V CH4 5.00A Ω M2.00ms T 27.00% A CH3 8.60V 10725-020 4 2 Figure 20. Soft Start with Full Load SYNC EN 3 2 VOUT 1 SW PGOOD 2 4 IL B W CH2 5.00V CH4 2.00A Ω M2.00ms T 50.20% A CH2 3.90V CH2 5.00V CH4 10.0V Figure 18. Voltage Precharged Output M1.00µs T 50.00% A CH2 Figure 21. External Synchronization Rev. A | Page 9 of 24 3.40V 10725-021 CH1 2.00V CH3 10.0V 10725-018 4 ADP2384 Data Sheet VOUT (AC) VOUT (AC) 1 1 VIN SW IOUT 3 IL 4 B W CH4 2.00A Ω M200µs T 70.40% A CH4 2.52A B CH1 20.0mV CH3 5.00V BW Figure 22. Load Transient Response, 1 A to 4 A W CH2 10.0V B W M1.00ms A CH3 T 30.00% Figure 25. Line Transient Response, VIN from 8 V to 14 V, IOUT = 4 A VOUT VOUT 1 1 SW SW 2 2 IL IL 4 A CH1 1.48V CH1 2.00V Figure 23. Output Short Entry 4 4 LOAD CURRENT (A) 5 3 2 1 65 75 85 A CH1 M4.00ms T 78.80% 1.72V 2 VOUT = 1.2V VOUT = 1.8V VOUT = 2.5V VOUT = 3.3V VOUT = 5V 55 CH2 10.0V CH4 5.00A Ω 3 95 105 AMBIENT TEMPERATURE (°C) Figure 24. Output Current vs. Ambient Temperature at VIN = 12 V, fSW = 600 kHz 0 45 10725-024 0 45 W Figure 26. Output Short Recovery 5 1 B 10725-026 M4.00ms T 30.40% VOUT = 1V VOUT = 1.2V VOUT = 1.8V VOUT = 2.5V VOUT = 3.3V VOUT = 5V 55 65 75 85 95 105 AMBIENT TEMPERATURE (°C) Figure 27. Output Current vs. Ambient Temperature at VIN = 12 V, fSW = 300 kHz Rev. A | Page 10 of 24 10725-027 CH2 10.0V CH4 5.00A Ω 10725-023 4 CH1 2.00V BW LOAD CURRENT (A) 12.0V 10725-025 CH1 100mV 10725-022 2 Data Sheet ADP2384 FUNCTIONAL BLOCK DIAGRAM VREG CLK RT OSC BIAS AND DRIVER REGULATOR PVIN SLOPE RAMP SYNC UVLO EN EN_BUF BOOST REGULATOR 1.17V 1µA 4µA ACS SLOPE RAMP Σ VI_MAX + OCP – HICCUP MODE BST COMP 0.6V + SS + AMP FB – DRIVER SW CONTROL LOGIC AND MOSFET DRIVER WITH ANTICROSS PROTECTION OVP 0.7V NFET + CMP – ISS NFET DRIVER CLK PGND – NEG CURRENT – CMP + + – 0.54V VREG VI_NEG + PGOOD DEGLITCH 10725-028 GND Figure 28. Functional Block Diagram Rev. A | Page 11 of 24 ADP2384 Data Sheet THEORY OF OPERATION The ADP2384 operates from an input voltage that ranges from 4.5 V to 20 V and regulates the output voltage from 0.6 V to 90% of the input voltage. Additional features that maximize design flexibility include the following: programmable switching frequency, programmable soft start, external compensation, precision enable, and a power-good output. BOOTSTRAP CIRCUITRY The ADP2384 includes a regulator to provide the gate drive voltage for the high-side N-MOSFET. It uses differential sensing to generate a 5 V bootstrap voltage between the BST and SW pins. It is recommended that a 0.1 µF, X7R or X5R ceramic capacitor be placed between the BST pin and the SW pin. OSCILLATOR The ADP2384 switching frequency is controlled by the RT pin. A resistor from RT to GND can program the switching frequency according to the following equation: CONTROL SCHEME PRECISION ENABLE/SHUTDOWN The EN input pin has a precision analog threshold of 1.17 V (typical) with 100 mV of hysteresis. When the enable voltage exceeds 1.17 V, the regulator turns on; when it falls below 1.07 V (typical), the regulator turns off. To force the regulator to automatically start when input power is applied, connect EN to PVIN. 1400 1200 1000 INTERNAL REGULATOR (VREG) The on-board regulator provides a stable supply for the internal circuits. It is recommended that a 1 µF ceramic capacitor be placed between the VREG pin and GND. The internal regulator includes a current-limit circuit to protect the output if the maximum external load current is exceeded. 800 600 400 200 The precision EN pin has an internal pull-down current source (5 µA) that provides a default turn-off when the EN pin is open. When the EN pin voltage exceeds 1.17 V (typical), the ADP2384 is enabled and the internal pull-down current source at the EN pin decreases to 1 µA, which allows users to program the PVIN UVLO and hysteresis. RT (k Ω) + 15 A 100 kΩ resistor sets the frequency to 600 kHz, and a 42.2 kΩ resistor sets the frequency to 1.2 MHz. Figure 29 shows the typical relationship between fSW and RT. FREQUENCY (kHz) The ADP2384 uses a fixed frequency, peak current mode PWM control architecture. At the start of each oscillator cycle, the high-side N-MOSFET is turned on, putting a positive voltage across the inductor. When the inductor current crosses the peak inductor current threshold, the high-side N-MOSFET is turned off and the low-side N-MOSFET is turned on. This puts a negative voltage across the inductor, causing the inductor current to decrease. The low-side N-MOSFET stays on for the rest of the cycle (see Figure 17). 69,120 fSW (kHz) = 0 20 60 100 140 180 220 RT (kΩ) 260 300 10725-029 The ADP2384 is a synchronous step-down, dc-to-dc regulator that uses a current mode architecture with an integrated highside power switch and a low-side synchronous rectifier. The regulator targets high performance applications that require high efficiency and design flexibility. Figure 29. Switching Frequency vs. RT SYNCHRONIZATION To synchronize the ADP2384, connect an external clock to the SYNC pin. The frequency of the external clock can be in the range of 200 kHz to 1.4 MHz. During synchronization, the regulator operates in continuous conduction mode (CCM), and the rising edge of the switching waveform runs 180° out of phase to the rising edge of the external clock. When the ADP2384 operates in synchronization mode, a resistor must be connected from the RT pin to GND to program the internal oscillator to run at 90% to 110% of the external synchronization clock. Rev. A | Page 12 of 24 Data Sheet ADP2384 SOFT START VOUT RISING 1600 f SW (kHz) (ms) PGOOD A slower soft start time can be programmed by using the SS pin. When a capacitor is connected between the SS pin and GND, an internal current charges the capacitor to establish the soft start ramp. The soft start time is calculated using the following equation: tSS_EXT = 105% 100% 95% 90% 0.6 V × CSS I SS _ UP where: CSS is the soft start capacitance. ISS_UP is the soft start pull-up current (3.2 µA). The internal error amplifier includes three positive inputs: the internal reference voltage, the internal digital soft start voltage, and the SS pin voltage. The error amplifier regulates the FB voltage to the lowest of the three voltages. If the output voltage is charged prior to turn-on, the ADP2384 prevents reverse inductor current that would discharge the output capacitor. This function remains active until the soft start voltage exceeds the voltage on the FB pin. POWER GOOD The power-good pin (PGOOD) is an active high, open-drain output that requires an external resistor to pull it up to a voltage. A logic high on the PGOOD pin indicates that the voltage on the FB pin (and, therefore, the output voltage) is within regulation. The power-good circuitry monitors the output voltage on the FB pin and compares it to the rising and falling thresholds that are specified in Table 1. If the rising output voltage exceeds the target value, the PGOOD pin is held low. The PGOOD pin continues to be held low until the falling output voltage returns to the target value. If the output voltage falls below the target output voltage, the PGOOD pin is held low. The PGOOD pin continues to be held low until the rising output voltage returns to the target value. The power-good rising and falling thresholds are shown in Figure 30. There is a 1024-cycle waiting period before the PGOOD pin is pulled from low to high, and there is a 16-cycle waiting period before the PGOOD pin is pulled from high to low. 1024 CYCLE DEGLITCH 16 CYCLE DEGLITCH 1024 CYCLE DEGLITCH 16 CYCLE DEGLITCH 10725-130 tSS_INT = 116.7% VOUT (%) The ADP2384 has integrated soft start circuitry to limit the output voltage rising time and reduce inrush current at startup. The internal soft start time is calculated using the following equation: VOUT FALLING Figure 30. PGOOD Rising and Falling Thresholds PEAK CURRENT-LIMIT AND SHORT-CIRCUIT PROTECTION The ADP2384 has a peak current-limit protection circuit to prevent current runaway. During the initial soft start, the ADP2384 uses frequency foldback to prevent output current runaway. The switching frequency is reduced according to the voltage on the FB pin, which allows more time for the inductor to discharge. The correlation between the switching frequency and the FB pin voltage is shown in Table 5. Table 5. FB Pin Voltage and Switching Frequency FB Pin Voltage VFB ≥ 0.4 V 0.4 V > VFB ≥ 0.2 V VFB < 0.2 V Switching Frequency fSW fSW/2 fSW/4 For protection against heavy loads, the ADP2384 uses a hiccup mode for overcurrent protection. When the inductor peak current reaches the current-limit value, the high-side MOSFET turns off and the low-side MOSFET turns on until the next cycle. The overcurrent counter increments during this process. If the overcurrent counter reaches 10 or the FB pin voltage falls to 0.4 V after the soft start, the regulator enters hiccup mode. The high-side and low-side MOSFETs are both turned off. The regulator remains in hiccup mode for 4096 clock cycles and then attempts to restart. If the current-limit fault has cleared, the regulator resumes normal operation. Otherwise, it reenters hiccup mode. The ADP2384 also provides a sink current limit to prevent the low-side MOSFET from sinking a lot of current from the load. When the voltage across the low-side MOSFET exceeds the sink current-limit threshold, which is typically 20 mV, the low-side MOSFET turns off immediately for the rest of the cycle. Both highside and low-side MOSFETs turn off until the next clock cycle. In some cases, the input voltage (VPVIN) ramp rate is too slow or the output capacitor is too large for the output to reach regulation during the soft start process, which causes the regulator to enter the hiccup mode. To avoid such occurrences, use a resistor divider at the EN pin to program the input voltage UVLO, or use a longer soft start time. Rev. A | Page 13 of 24 ADP2384 Data Sheet OVERVOLTAGE PROTECTION (OVP) THERMAL SHUTDOWN The ADP2384 includes an overvoltage protection feature to protect the regulator against an output short to a higher voltage supply or when a strong load disconnect transient occurs. If the feedback voltage increases to 0.7 V, the internal high-side and low-side MOSFETs are turned off until the voltage at the FB pin decreases to 0.63 V. At that time, the ADP2384 resumes normal operation. If the ADP2384 junction temperatures rises above 150°C, the internal thermal shutdown circuit turns off the regulator for selfprotection. Extreme junction temperatures can be the result of high current operation, poor circuit board thermal design, and/or high ambient temperature. A 25°C hysteresis is included in the thermal shutdown circuit so that, if an overtemperature event occurs, the ADP2384 does not return to normal operation until the on-chip temperature falls below 125°C. Upon recovery, a soft start is initiated before normal operation begins. UNDERVOLTAGE LOCKOUT (UVLO) Undervoltage lockout circuitry is integrated in the ADP2384 to prevent the occurrence of power-on glitches. If the VPVIN voltage falls below 3.8 V typical, the part shuts down and both the power switch and synchronous rectifier turn off. When the VPVIN voltage rises above 4.3 V typical, the soft start period is initiated and the part is enabled. Rev. A | Page 14 of 24 Data Sheet ADP2384 APPLICATIONS INFORMATION INPUT CAPACITOR SELECTION The input capacitor reduces the input voltage ripple caused by the switch current on PVIN. Place the input capacitor as close as possible to the PVIN pin. A ceramic capacitor in the 10 μF to 47 μF range is recommended. The loop that is composed of this input capacitor, the high-side N-MOSFET, and the low-side N-MOSFET must be kept as small as possible. The voltage rating of the input capacitor must be greater than the maximum input voltage. The rms current rating of the input capacitor should be larger than the value calculated from the following equation: ICIN_RMS = IOUT × D × (1 − D) OUTPUT VOLTAGE SETTING The output voltage of the ADP2384 is set by an external resistive divider. The resistor values are calculated using R VOUT = 0.6 × 1 + TOP RBOT The maximum output voltage for a given input voltage and switching frequency is constrained by the minimum off time and the maximum duty cycle. The minimum off time is typically 200 ns, and the maximum duty cycle of the ADP2384 is typically 90%. The maximum output voltage, limited by the minimum off time at a given input voltage and frequency, can be calculated using the following equation: VOUT_MAX = VIN × (1 − tMIN_OFF × fSW) − (RDSON_HS − RDSON_LS) × IOUT_MAX × (1 − tMIN_OFF × fSW) − (RDSON_LS + RL) × IOUT_MAX (2) where: VOUT_MAX is the maximum output voltage. tMIN_OFF is the minimum off time. IOUT_MAX is the maximum output current. The maximum output voltage, limited by the maximum duty cycle at a given input voltage, can be calculated by using the following equation: VOUT_MAX = DMAX × VIN (3) where DMAX is the maximum duty cycle. To limit output voltage accuracy degradation due to FB bias current (0.1 µA maximum) to less than 0.5% (maximum), ensure that RBOT < 30 kΩ. As shown in Equation 1 to Equation 3, reducing the switching frequency alleviates the minimum on time and minimum off time limitation. Table 6 lists the recommended resistor divider values for various output voltages. INDUCTOR SELECTION Table 6. Resistor Divider Values for Various Output Voltages VOUT (V) 1.0 1.2 1.5 1.8 2.5 3.3 5.0 RTOP ± 1% (kΩ) 10 10 15 20 47.5 10 22 RBOT ± 1% (kΩ) 15 10 10 10 15 2.21 3 The inductor value is determined by the operating frequency, input voltage, output voltage, and inductor ripple current. Using a small inductor value leads to a faster transient response but degrades efficiency, due to a larger inductor ripple current; using a large inductor value leads to smaller ripple current and better efficiency but results in a slower transient response. As a guideline, the inductor ripple current, ΔIL, is typically set to one-third of the maximum load current. The inductor value is calculated using the following equation: L= VOLTAGE CONVERSION LIMITATIONS The minimum output voltage for a given input voltage and switching frequency is constrained by the minimum on time. The minimum on time of the ADP2384 is typically 125 ns. The minimum output voltage for a given input voltage and switching frequency can be calculated using the following equation: VOUT_MIN = VIN × tMIN_ON × fSW − (RDSON_HS − RDSON_LS) × IOUT_MIN × tMIN_ON × fSW − (RDSON_LS + RL) × IOUT_MIN where: VOUT_MIN is the minimum output voltage. tMIN_ON is the minimum on time. fSW is the switching frequency. RDSON_HS is the high-side MOSFET on resistance. RDSON_LS is the low-side MOSFET on resistance. IOUT_MIN is the minimum output current. RL is the series resistance of the output inductor. (1) (VIN − VOUT ) × D ∆I L × f SW where: VIN is the input voltage. VOUT is the output voltage. D is the duty cycle (D = VOUT/VIN). ΔIL is the inductor current ripple. fSW is the switching frequency. The ADP2384 uses adaptive slope compensation in the current loop to prevent subharmonic oscillations when the duty cycle is larger than 50%. The internal slope compensation limits the minimum inductor value. Rev. A | Page 15 of 24 ADP2384 Data Sheet For a duty cycle that is larger than 50%, the minimum inductor value is determined using the following equation: L (Minimum) = VOUT × (1 − D ) ∆I L 2 The saturation current of the inductor must be larger than the peak inductor current. For ferrite core inductors with a quick saturation characteristic, the saturation current rating of the inductor should be higher than the current-limit threshold of the switch. This prevents the inductor from reaching saturation. IOUT 2 + 2 × (VIN − VOUT ) × ∆VOUT _ UV Another example occurs when a load is suddenly removed from the output, and the energy stored in the inductor rushes into the output capacitor, causing the output to overshoot. The output capacitance that is required to meet the overshoot requirement can be calculated using the following equation: COUT_OV = The rms current of the inductor is calculated as follows: IRMS = KUV × ∆I STEP 2 × L where: KUV is a factor, with a typical setting of KUV = 2. ΔISTEP is the load step. ΔVOUT_UV is the allowable undershoot on the output voltage. 2 × ΔI L × f SW The peak inductor current is calculated by IPEAK = IOUT + COUT_UV = ∆I L 2 12 Shielded ferrite core materials are recommended for low core loss and low EMI. Table 7 lists some recommended inductors. OUTPUT CAPACITOR SELECTION (VOUT + ∆VOUT _ OV )2 − VOUT 2 where: ΔVOUT_OV is the allowable overshoot on the output voltage. KOV is a factor, with a typical setting of KOV = 2. The output ripple is determined by the ESR and the value of the capacitance. Use the following equation to select a capacitor that can meet the output ripple requirements: The output capacitor selection affects the output ripple voltage load step transient and the loop stability of the regulator. For example, during a load step transient where the load is suddenly increased, the output capacitor supplies the load until the control loop can ramp up the inductor current. The delay caused by the control loop causes output undershoot. The output capacitance that is required to satisfy the voltage droop requirement can be calculated using the following equation: K OV × ∆I STEP 2 × L COUT_RIPPLE = RESR = ∆I L 8 × f SW × ∆VOUT _ RIPPLE ∆VOUT _ RIPPLE ∆I L where: ΔVOUT_RIPPLE is the allowable output ripple voltage. RESR is the equivalent series resistance of the output capacitor in ohms (Ω). Table 7. Recommended Inductors Vendor Toko Vishay Wurth Elektronik Part No. FDVE1040-1R5M FDVE1040-2R2M FDVE1040-3R3M FDVE1040-4R7M FDVE1040-6R8M FDVE1040-100M IHLP4040DZ-1R0M-01 IHLP4040DZ-1R5M-01 IHLP4040DZ-2R2M-01 IHLP4040DZ-3R3M-01 IHLP4040DZ-4R7M-01 IHLP4040DZ-6R8M-01 IHLP4040DZ-100M-01 744325120 744325180 744325240 744325330 744325420 744325550 Value (µH) 1.5 2.2 3.3 4.7 6.8 10 1.0 1.5 2.2 3.3 4.7 6.8 10 1.2 1.8 2.4 3.3 4.2 5.5 Rev. A | Page 16 of 24 ISAT (A) 13.7 11.4 9.8 8.2 7.1 6.1 36 27.5 25.6 18.6 17 13.5 12 25 18 17 15 14 12 IRMS (A) 14.6 11.6 9.0 8.0 7.1 5.2 17.5 15 12 10 9.5 8.0 6.8 20 16 14 12 11 10 DCR (mΩ) 4.6 6.8 10.1 13.8 20.2 34.1 4.1 5.8 9 14.4 16.5 23.3 36.5 1.8 3.5 4.75 5.9 7.1 10.3 Data Sheet ADP2384 Select the largest output capacitance given by COUT_UV, COUT_OV, and COUT_RIPPLE to meet both load transient and output ripple performance. The selected output capacitor voltage rating must be greater than the output voltage. The rms current rating of the output capacitor must be larger than the value that is calculated by ICOUT_RMS = ∆I L 12 where: AVI = 8.7 A/V. R is the load resistance. COUT is the output capacitance. RESR is the equivalent series resistance of the output capacitor. The ADP2384 uses a transconductance amplifier for the error amplifier and to compensate the system. Figure 32 shows the simplified, peak current mode control, small signal circuit. VOUT PROGRAMMING THE INPUT VOLTAGE UVLO The ADP2384 has a precision enable input that can be used to program the UVLO threshold of the input voltage (see Figure 31). VOUT RTOP RBOT PVIN VCOMP – gm + + COUT AVI R RC ADP2384 CCP – RESR 10725-031 CC RTOP_EN EN CMP EN Figure 32. Simplified Peak Current Mode Control, Small Signal Circuit The compensation components, RC and CC, contribute a zero, and RC and the optional CCP contribute an optional pole. 1.17V RBOT_EN 4µA The closed-loop transfer equation is as follows: 10725-030 1µA TV (s) = Figure 31. Programming the Input Voltage UVLO Use the following equation to calculate RTOP_EN and RBOT_EN: RTOP_EN = RBOT_EN = 1.07 V × 5μA − 1.17 V × 1 μA 1.17 V × RTOP _ EN CC + CCP × × GVD (s) The following design guideline shows how to select the RC, CC, and CCP compensation components for ceramic output capacitor applications: VIN _ RISING − RTOP _ EN × 5μA − 1.17 V 1. COMPENSATION DESIGN 2. For peak current mode control, the power stage can be simplified as a voltage controlled current source supplying current to the output capacitor and load resistor. It is composed of one domain pole and a zero that is contributed by the output capacitor ESR. The control-to-output transfer function is based on the following: fP = −gm R × CC × CCP × s s × 1 + C CC + CCP where: VIN_RISING is the VIN rising threshold. VIN_FALLING is the VIN falling threshold. fZ = RBOT + RTOP × 1 + RC × CC × s 1.07 V × VIN _ RISING − 1.17 V × VIN _ FALLING s 1 + 2× π× fZ GVD (s) = VOUT (s)/VCOMP (s) = AVI × R × s 1 + 2× π× fP RBOT Determine the cross frequency, fC. Generally, fC is between fSW/12 and fSW/6. Calculate RC using the following equation: RC = 3. 1 1 2 × π × (R + RESR ) × COUT Rev. A | Page 17 of 24 (R + RESR ) × COUT RC CCP is optional. It can be used to cancel the zero caused by the ESR of the output capacitor. CCP = 2 × π × RESR × COUT 0.6 V × g m × AVI Place the compensation zero at the domain pole, fP; then determine CC by using the following equation: CC = 4. 2 × π × VOUT × COUT × fC RESR × COUT RC ADP2384 Data Sheet ADIsimPower DESIGN TOOL The ADP2384 is supported by the ADIsimPower™ design tool set. ADIsimPower is a collection of tools that produce complete power designs that are optimized for a specific design goal. The tools enable the user to generate a full schematic and bill of materials and calculate performance in minutes. ADIsimPower can optimize designs for cost, area, efficiency, and part count, while taking into consideration the operating conditions and limitations of the IC and all real external components. For more information about theADIsimPower design tools, refer to www.analog.com/ADIsimPower. The tool set is available from this website, and users can request an unpopulated board. Rev. A | Page 18 of 24 Data Sheet ADP2384 DESIGN EXAMPLE ADP2384 PVIN CIN 10µF 25V BST CBST L1 0.1µF 3.3µH EN RT 100kΩ CVREG 1µF CSS 22nF VOUT = 3.3V SW PGOOD COUT1 47µF 6.3V RTOP 10kΩ 1% SYNC COUT2 47µF 6.3V FB RT COMP VREG SS GND PGND CCP 3.9pF RC 31.6kΩ CC 1500pF RBOT 2.21kΩ 1% 10725-032 VIN = 12V Figure 33. Schematic for Design Example This section describes the procedures for selecting the external components, based on the example specifications that are listed in Table 8. See Figure 33 for the schematic of this design example. Table 8. Step-Down DC-to-DC Regulator Requirements Parameter Input Voltage Output Voltage Output Current Output Voltage Ripple Load Transient Switching Frequency ∆IL = 1.2 A. fSW = 600 kHz. This calculation results in L = 3.323 μH. Choose the standard inductor value of 3.3 μH. The peak-to-peak inductor ripple current can be calculated using the following equation: Specification VIN = 12.0 V ± 10% VOUT = 3.3 V IOUT = 4 A ∆VOUT_RIPPLE = 33 mV ±5%, 1 A to 4 A, 2 A/μs fSW = 600 kHz ΔIL = (VIN − VOUT ) × D L × f SW This calculation results in ∆IL = 1.21 A. OUTPUT VOLTAGE SETTING (DESIGN EXAMPLE) Choose a 10 kΩ resistor as the top feedback resistor (RTOP), and calculate the bottom feedback resistor (RBOT) by using the following equation: 0. 6 RBOT = RTOP × V OUT − 0.6 Use the following equation to calculate the peak inductor current: IPEAK = IOUT + ∆I L 2 This calculation results in IPEAK = 4.605 A. Use the following equation to calculate the rms current flowing through the inductor: To set the output voltage to 3.3 V, the resistors values are as follows: RTOP = 10 kΩ, and RBOT = 2.21 kΩ. IRMS = IOUT 2 + ∆I L 2 12 FREQUENCY SETTING This calculation results in IRMS = 4.015 A. Connect a 100 kΩ resistor from the RT pin to GND to set the switching frequency to 600 kHz. INDUCTOR SELECTION (DESIGN EXAMPLE) Based on the calculated current value, select an inductor with a minimum rms current rating of 4.02 A and a minimum saturation current rating of 4.61 A. The peak-to-peak inductor ripple current, ∆IL, is set to 30% of the maximum output current. Use the following equation to estimate the inductor value: However, to protect the inductor from reaching its saturation point under the current-limit condition, the inductor should be rated for at least a 6 A saturation current for reliable operation. L= (VIN − VOUT ) × D ∆I L × f SW Based on the requirements described previously, select a 3.3 μH inductor, such as the FDVE1040-3R3M from Toko, which has a 10.1 mΩ DCR and a 9.8 A saturation current. where: VIN = 12 V. VOUT = 3.3 V. D = 0.275. Rev. A | Page 19 of 24 ADP2384 Data Sheet OUTPUT CAPACITOR SELECTION (DESIGN EXAMPLE) CC = The output capacitor is required to meet both the output voltage ripple and load transient response requirements. To meet the output voltage ripple requirement, use the following equation to calculate the ESR and capacitance value of the output capacitor: = 3.9 pF ∆I L To meet the ±5% overshoot and undershoot transient requirements, use the following equations to calculate the capacitance: K OV × ∆I STEP × L 2 (VOUT + ∆VOUT _ OV )2 − VOUT 2 KUV × ∆I STEP 2 × L 60 180 48 144 36 108 24 72 12 36 0 0 –12 –36 –24 –72 –36 –108 –48 –144 –60 1k 2 × (VIN − VOUT ) × ∆VOUT _ UV PHASE (Degrees) 8 × f S × ∆VOUT _ RIPPLE This calculation results in COUT_RIPPLE = 7.6 μF, and RESR = 27 mΩ. COUT_UV = 32.5 k Ω Figure 34 shows the bode plot at 4 A. The cross frequency is 59 kHz, and the phase margin is 55°. ∆VOUT _ RIPPLE COUT_OV = 0.002 Ω × 2 × 32 μF = 1629 pF Choose standard components, as follows: RC = 31.6 kΩ, CC = 1500 pF, and CCP = 3.9 pF. MAGNITUDE (dB) RESR = ∆I L 32.5 k Ω –180 10k 100k 1M FREEQUENCY (Hz) 10725-040 COUT_RIPPLE = CCP = (0.825 Ω + 0.002 Ω) × 2 × 32 μF Figure 34. Bode Plot at 4 A where: KOV = KUV = 2 are the coefficients for estimation purposes. ∆ISTEP = 3 A is the load transient step. ∆VOUT_OV = 5%VOUT is the overshoot voltage. ∆VOUT_UV = 5%VOUT is the undershoot voltage. SOFT START TIME PROGRAM This calculation results in COUT_OV = 53.2 μF, and COUT_UV = 20.7 μF. According to the calculation, the output capacitance must be greater than 53 μF, and the ESR of the output capacitor must be smaller than 27 mΩ. It is recommended that two pieces of 47 μF/X5R/6.3 V ceramic capacitors be used, such as the GRM32ER60J476ME20 from Murata, with an ESR of 2 mΩ. The soft start feature allows the output voltage to ramp up in a controlled manner, eliminating output voltage overshoot during soft start and limiting the inrush current. Set the soft start time to 4 ms. CSS = t SS _ EXT × I SS _UP 0. 6 = 4 ms × 3.2 μA 0.6 V = 21.3 nF Choose a standard component value, as follows: CSS = 22 nF. COMPENSATION COMPONENTS INPUT CAPACITOR SELECTION (DESIGN EXAMPLE) For better load transient and stability performance, set the cross frequency, fC, to fSW/10. In this case, fSW is running at 600 kHz; therefore, the fC is set to 60 kHz. A minimum 10 μF ceramic capacitor must be placed near the PVIN pin. In this application, it is recommended that one 10 μF, X5R, 25 V ceramic capacitor be used. The 47 µF ceramic output capacitor has a derated value of 32 µF. RC = 2 × π × 3.3 V × 2 × 32 μF × 60 kHz 0.6 V × 470 μS × 8.7 A/V = 32.5 kΩ Rev. A | Page 20 of 24 Data Sheet ADP2384 RECOMMENDED EXTERNAL COMPONENTS Table 9. Recommended External Components for Typical Applications with 4 A Output Current fSW (kHz) 300 600 1000 1 VIN (V) 12 12 12 12 12 12 12 5 5 5 5 5 5 12 12 12 12 12 5 5 5 5 5 5 12 12 12 5 5 5 5 5 5 VOUT (V) 1 1.2 1.5 1.8 2.5 3.3 5 1 1.2 1.5 1.8 2.5 3.3 1.5 1.8 2.5 3.3 5 1 1.2 1.5 1.8 2.5 3.3 2.5 3.3 5 1 1.2 1.5 1.8 2.5 3.3 L (µH) 2.2 3.3 3.3 4.7 4.7 6.8 10 2.2 2.2 3.3 3.3 3.3 3.3 2.2 2.2 2.2 3.3 4.7 1 1 1.5 1.5 1.5 1.5 1.5 2.2 2.2 1 1 1 1 1 1 COUT (µF) 1 680 680 470 470 2 × 100 2 × 100 100 + 47 680 470 470 3 × 100 2 × 100 2 × 100 3 × 100 2 × 100 2 × 47 2 × 47 100 3 × 100 2 × 100 2 × 100 100 + 47 100 100 100 100 100 3 × 100 2 × 100 100 + 47 2 × 47 100 100 RTOP (kΩ) 10 10 15 20 47.5 10 22 10 10 15 20 47.5 10 15 20 47.5 10 22 10 10 15 20 47.5 10 47.5 10 22 10 10 15 20 47.5 10 RBOT (kΩ) 15 10 10 10 15 2.21 3 15 10 10 10 15 2.21 10 10 15 2.21 3 15 10 10 10 15 2.21 15 2.21 3 15 10 10 10 15 2.21 RC (kΩ) 47 59 47 60.4 22 29.4 34 47 39 47 24 22 29.4 39 31.6 24 31.6 44.2 26.7 21 26.7 24 22 28 37.4 47 69 43.2 33 33 30 37.4 47 CC (pF) 3300 3300 3300 3300 3300 3300 3300 3300 3300 3300 3300 3300 3300 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1000 1000 1000 1000 1000 1000 1000 1000 1000 CCP (pF) 150 100 100 68 10 8.2 4.7 150 100 100 15 10 8.2 10 8.2 4.7 4.7 2.2 10 10 10 8.2 4.7 4.7 3.3 2.2 1 8.2 6.8 4.7 4.7 3.3 2.2 680 μF: 4 V, Sanyo 4TPF680M; 470 μF: 6.3 V, Sanyo 6TPF470M; 100 μF: 6.3 V, X5R, Murata GRM32ER60J107ME20; 47 μF: 6.3 V, X5R, Murata GRM32ER60J476ME20. Rev. A | Page 21 of 24 ADP2384 Data Sheet CIRCUIT BOARD LAYOUT RECOMMENDATIONS Good printed circuit board (PCB) layout is essential for obtaining the best performance from the ADP2384. Poor PCB layout can degrade the output regulation, as well as the electromagnetic interference (EMI) and electromagnetic compatibility (EMC) performance. Figure 36 shows an example of a good PCB layout for the ADP2384. For optimum layout, refer to the following guidelines: • • • ADP2384 VIN PVIN CIN BST CBST EN RTOP SYNC VREG CVREG RC SS GND PGND CSS CC PULL UP PVIN PGOOD SYNC RT EN RT CC SS PVIN COMP PVIN FB GND PVIN VREG PVIN BST CVREG GND SW SW SW SW INPUT INPUT BYPASS BULK CAP CAP CBST + PGND PGND PGND PGND PGND PGND SW SW INDUCTOR POWER GROUND PLANE OUTPUT CAPACITOR 10725-034 VOUT VIA BOTTOM LAYER TRACE COPPER PLANE Figure 36. Recommended PCB Layout Rev. A | Page 22 of 24 10725-033 RT RBOT COMP RT ANALOG GROUND PLANE RTOP COUT FB Figure 35. High Current Path in the PCB Circuit RBOT VOUT L SW PGOOD CSS • RC • CCP • Use separate analog ground planes and power ground planes. Connect the ground reference of sensitive analog circuitry, such as output voltage divider components, to analog ground. In addition, connect the ground reference of power components, such as input and output capacitors, to power ground. Connect both ground planes to the exposed GND pad of the ADP2384. Place the input capacitor, inductor, and output capacitor as close as possible to the IC, and use short traces. Ensure that the high current loop traces are as short and as wide as possible. Make the high current path from the input capacitor through the inductor, the output capacitor, and the power ground plane back to the input capacitor as short as possible. To accomplish this, ensure that the input and output capacitors share a common power ground plane. In addition, ensure that the high current path from the power ground plane through the inductor and output capacitor back to the power ground plane is as short as possible by tying the PGND pins of the ADP2384 to the PGND plane as close as possible to the input and output capacitors. Connect the exposed GND pad of the ADP2384 to a large, external copper ground plane to maximize its power dissipation capability and minimize junction temperature. In addition, connect the exposed SW pad to the SW pins of the ADP2384 using short, wide traces; or connect the exposed SW pad to a large copper plane of the switching node for high current flow. Place the feedback resistor divider network as close as possible to the FB pin to prevent noise pickup. Minimize the length of the trace that connects the top of the feedback resistor divider to the output while keeping the trace away from the high current traces and the switching node to avoid noise pickup. To further reduce noise pickup, place an analog ground plane on either side of the FB trace and ensure that the trace is as short as possible to reduce the parasitic capacitance pickup. Data Sheet ADP2384 TYPICAL APPLICATIONS CIRCUITS ADP2384 BST PVIN CIN 10µF 25V CBST L1 0.1µF 1.5µH EN RT 124kΩ CVREG 1µF VOUT = 1.2V SW PGOOD COUT1 100µF 6.3V RTOP 10kΩ 1% SYNC COUT2 100µF 6.3V COUT3 100µF 6.3V FB RT SS CCP 10pF GND PGND CSS 22nF RBOT 10kΩ 1% COMP VREG RC 27.4kΩ CC 2.2nF 10725-036 VIN = 12V Figure 37. Typical Applications Circuit, VIN = 12 V, VOUT = 1.2 V, IOUT = 4 A, fSW = 500 kHz ADP2384 BST PVIN CIN 10µF 25V CBST L1 0.1µF 2.2µH EN SW PGOOD RT 100kΩ CVREG 1µF RTOP 20kΩ 1% SYNC VOUT = 1.8V COUT1 100µF 6.3V COUT2 100µF 6.3V FB RT COMP VREG SS CCP 8.2pF GND PGND RC 31.6kΩ CC 1.5nF RBOT 10kΩ 1% 10725-035 VIN = 12V Figure 38. Typical Applications Circuit Using Internal Soft Start, VIN = 12 V, VOUT = 1.8 V, IOUT = 4 A, fSW = 600 kHz ADP2384 BST PVIN CIN 10µF 25V CBST L1 0.1µF 4.7µH EN SW PGOOD RT 124kΩ RTOP 22kΩ 1% SYNC CSS 22nF VOUT = 5V FB RT COMP VREG CVREG 1µF COUT 100µF 6.3V SS GND PGND CCP 2.2pF RC 44.2kΩ CC 1.5nF RBOT 3kΩ 1% 10725-037 VIN = 12V Figure 39. Typical Applications Circuit with Programming Switching Frequency at 500 kHz, VIN = 12 V, VOUT = 5 V, IOUT = 4 A, fSW = 500 kHz Rev. A | Page 23 of 24 ADP2384 Data Sheet OUTLINE DIMENSIONS PIN 1 INDICATOR 0.20 MIN 0.20 MIN 2.80 2.70 2.60 0.20 MIN 19 24 18 1 EXPOSED PAD 0.50 BSC 0.35 0.25 EXPOSED PAD 6 13 TOP VIEW 0.80 0.75 0.70 SEATING PLANE 0.50 0.40 0.30 12 0.30 0.25 0.20 7 BOTTOM VIEW 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.203 REF PIN 1 INDICATOR 1.50 1.40 1.30 0.45 1.05 0.95 0.85 0.20 MIN FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. COMPLIANT TO JEDEC STANDARDS MO-220-WGGD . 04-28-2014-C 4.10 4.00 SQ 3.90 Figure 40. 24-Lead Lead Frame Chip Scale Package [LFCSP_WQ] 4 mm × 4 mm Body, Very Very Thin Quad (CP-24-12) Dimensions shown in millimeters ORDERING GUIDE Model 1 ADP2384ACPZN-R7 ADP2384-EVALZ 1 Temperature Range −40°C to +125°C Package Description 24-Lead Lead Frame Chip Scale Package [LFCSP_WQ], 7” Tape and Reel Evaluation Board Z = RoHS Compliant Part. ©2012–2014 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D10725-0-7/14(A) Rev. A | Page 24 of 24 Package Option CP-24-12