SC410 - Semtech

SC410
3A EcoSpeed® Step-Down Regulator
with LDO and Ultrasonic Power Save
POWER MANAGEMENT
Features













Description
Input voltage — 5.5V to 24V
Output voltage — 0.75V to 7.5V
Output current — Up to 3A
Internal reference — + 1%
Small ceramic capacitors
Power good pin (open-drain)
Adaptive on-time control:
Excellent transient response
Programmable pseudo-fixed frequency during
CCM
Fault protection features:
Cycle-by-cycle current limit
Short circuit protection
Over and under output voltage protection
Over-temperature
Internal soft-start
Ultrasonic power save and smart PSAVE
Internal LDO for bias voltage
Ultra-small lead-free 3 x 3mm, 10-Pin MLPD package
WEEE and RoHS compliant
•
•
•
•
•
•
Applications





The SC410 is an integrated, synchronous 3A EcoSpeed®
step-down regulator. It incorporates Semtech’s advanced,
patented adaptive on-time architecture to achieve bestin-class dynamic performance using point-of-load applications. The input voltage range is 5.5V to 24V with a
programmable output voltage from 0.75V up to 7.5V. The
device features an internal LDO and ultrasonic PSAVE
mode for high efficiency across the output load range.
Adaptive on-time control provides programmable
pseudo-fixed frequency operation in continuous conduction and excellent transient performance. The switching
frequency can be set from 200kHz to 1MHz, allowing the
designer to reduce external LC filtering and minimize light
load (standby) losses.
Additional features include cycle-by-cycle current limit,
soft start, input UVLO and output OV protection, and over
temperature protection. The open-drain PGOOD pin provides output status. Standby current is less than 10μA
when disabled.
The device is available in a low profile, thermally enhanced
MLPD 3 x 3mm 10-pin package.
Networking Equipment, Embedded Systems
Medical Equipment, Office Automation
Instrumentation, Portable Systems
Consumer Devices such as DTV and Set-top Boxes
POL Converters
Typical Application Circuit
Enable
EN
SC410
PGOOD
PGOOD
CBST
VIN
VIN
TON
CIN
LX
VOUT
L1
COUT
RTON
CLDO2
RTOP
LDO
CLDO1
FB
AGND
Revision 4.0
BST
PGND
© 2011 Semtech Corporation
RBOT
SC410
Pin Configuration
BST
1
VIN
2
LX
Ordering Information
10
TOP VIEW
LDO
9
AGND
3
8
TON
PGND
4
7
EN
PGOOD
5
6
FB
Device
Package
SC410MLTRT(1)(2)
MLPD-10 3 x 3
SC410EVB
Evaluation Board
Notes:
(1) Available in tape and reel only. A reel contains 3,000 devices.
(2) Lead-free packaging only. Device is WEEE and RoHS compliant
and halogen-free.
MLPD; 3 x 3, 10 LEAD
θJA = 40°C/W
Marking Information
410
yyww
xxxx
yyww = Date code
xxxx = Lot number
SC410
Absolute Maximum Ratings
Recommended Operating Conditions
LX to GND (V). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to +28
Supply Input Voltage (V) . . . . . . . . . . . . . . . . . . . . . . . 5.5 to 24
VIN to PGND, EN to AGND (V). . . . . . . . . . . . . . . . . -0.3 to +28
Maximum Continuous Output Current (A) . . . . . . . . . . . . . 3
VIN to LDO (V). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 0 . 3
Maximum Peak Inductor Current (A). . . . . . . . . . . . . . . . . . 5.0
BST to LX (V). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to +6.0
Thermal Information
BST to PGND (V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to +34
LDO to AGND (V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to +6.0
Storage Temperature (°C ). . . . . . . . . . . . . . . . . . -60 to +150
FB, PGOOD, TON (V). . . . . . . . . . . . . . . . . . . . . -0.3 to LDO +0.3
Maximum Junction Temperature (°C ). . . . . . . . . . . . . . . . 150
AGND to PGND (V). . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to +0.3
Operating Junction Temperature (°C ). . . . . . . -40 to +125
Maximum Peak Inductor Current (A). . . . . . . . . . . . . . . . . 5 . 5
Thermal Resistance, Junction to Ambient(2) (°C/W ). . . . . 40
Peak IR Reflow Temperature (°C ). . . . . . . . . . . . . . . . . . . . . 260
ESD Protection Level (kV)(1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Exceeding the above specifications may result in permanent damage to the device or device malfunction. Operation outside of the parameters
specified in the Electrical Characteristics section is not recommended.
NOTES:
(1) Tested according to JEDEC standard JESD22-A114-B.
(2) Calculated from package in still air, mounted to 3 x 4.5 (in), 4 layer FR4 PCB with thermal vias under the exposed pad per JESD51 standards.
Electrical Characteristics
Unless specified: VIN =12V, TA=+25°C for Typ, -40°C to +85°C for Min and Max, TJ < 125°C, per detailed application circuit
Parameter
Conditions
Min
Typ
Max
Units
Input Supplies
VIN UVLO Threshold
Programmable with EN pin after 2 switching
cycles
1.5
V
50
mV
4
V
0.3
V
VEN = 0V
9
μA
IOUT= 0A, fSW=25kHz(1)
2.5
mA
VIN UVLO Hysteresis
Internal Bias UVLO Threshold
Rising UVLO V TH
Internal Bias UVLO Hysteresis
VIN Supply Current
Controller
FB On-Time Threshold
Frequency Programming Range
0.7425
See RTON Calculation
Minimum Frequency
during Ultrasonic PSAVE
FB Input Bias Current
FB=5V or 0V
0.75
200
0.7575
V
1000
kHz
22
-1
kHz
+1
μA
SC410
Electrical Characteristics (continued)
Parameter
Conditions
Min
Typ
Max
Units
Continuous Mode VIN=15V, VOUT=3V, RTON= 200kΩ
0.9
1
1.1
μs
Timing
On-Time
Minimum On-Time(1)
100
ns
Minimum Off-Time(1)
320
ns
850
µs
Soft start
Soft start Time(1)
Delay from PWM Switching to Output Regulation
Current Sense
Zero-Crossing Detector Threshold
LX - PGND
-10
0
+10
mV
Power Good
Power Good Threshold
PGOOD Delay Time(1)
Upper Limit, VFB > internal 750mV reference
120
Lower Limit, VFB < internal 750mV reference
90
Between VOUT at 90% of its regulation value
and the PGOOD signal transitioning to high
1
ms
5
µs
Noise Immunity Delay Time (1)
Leakage
%VREF
1
Power Good On-Resistance
µA
10
Ω
Fault Protection
Output Under-Voltage Fault
FB with Respect to REF,
8 Consecutive Switching Cycles
75
%VREF
Output Over-Voltage Fault
FB with Respect to REF
120
%VREF
Smart PowerSave Protection Threshold
FB with Respect to REF
110
%VREF
5
μs
145
°C
PWM Output Enabled(1)
1.5
V
LDO Output Enabled
0.8
V
OV, UV Fault Noise Immunity Delay (1)
Over-Temperature Shutdown (1)
OT Latched
Enable Logic
EN Input Bias Current
VEN = 5V
-10
10
μA
SC410
Electrical Characteristics (continued)
Parameter
Conditions
Min
Typ
Max
Units
Gate Drivers
BST Switch On resistance
25
Ω
3.2
A
Internal Power MOSFETs
Current Limit(2)
LX Leakage Current
Inductor Valley Current Limit, VLDO=5V
2.4
VIN=24V, LX=0V, High Side
1
High Side
215
Low Side
110
10
Switch Resistance
µA
mΩ
Non-overlap time (1)
15
ns
Linear Regulator (The LDO is shorted to the bias node, internally)
LDO Accuracy
LDO Current Limit
LDO Drop Out Voltage
-4
4
Short circuit protection, VIN = 12V, VLDO <80% of
final VLDO value
35
Operating current limit, VIN = 12V, VLDO > 80% of
final VLDO value
100
From VIN to VLDO, ILDO = 100mA
1.2
%VLDO
mA
V
Note:
(1) Typical value from EVB, not ATE tested.
(2) The minimum inductor valley current limit of 2.4V gives an average output current limit of 3A assuming 1.2A inductor ripple current.
SC410
Detailed Application Circuit-1
VLDO
RPGOOD
VIN
U1
CBST
VIN
+5.5 to +24VDC
1
0.1μF
2
CIN(1)
3
10µF
4
5
BST
S C 410
LDO
AGND
VIN
TON
LX
PGND
EN
PGOOD
FB
10
9
CLDO2
1μF
CLDO1
0.1μF
REN
8
7
10nF
6
RTON
90.9kΩ
VOUT
L1
2.2μH
RL
12.4kΩ
COUT2(1)
22µF
COUT3(1)
22µF
3A max.
CC
CC_1
NP
COUT1(1)
22µF
CL
10nF
47pF
CTOP NP
RBOT
10kΩ
R8
RTOP
0Ω
34kΩ
Position as close to IC as possible
Note: (1) Ceramic capacitors
SC410
Detailed Application Circuit-2
VLDO
RPGOOD
VIN
U1
CBST
VIN
+5.5 to +24VDC
1
0.1μF
2
3
CIN(1)
10µF
4
5
BST
S C 410
LDO
AGND
VIN
TON
LX
PGND
EN
PGOOD
FB
10
9
CLDO1
0.1μF
CLDO2
1μF
REN
8
7
10nF
6
RTON
90.9kΩ
VOUT
L1
2.2μH
COUT2(2)
3A max.
CTOP NP
RTOP
34kΩ
RBOT
10kΩ
R8
0Ω
Position as close to IC as possible
Notes: (1) Ceramic capacitor
( 2) Capacitor must provide sufficient ESR to provide stability for user’s application
SC410
Typical Characteristics
Characteristics are based on a circuit with VIN = 12V, L = 2.2µH (DCR = 35mΩ), COUT = 66µF, VOUT = 3.3V, RTON = 90.9kΩ.
Load Regulation
Efficiency — Power Loss
VIN = 12V
Efficiency
3.0
PLOSS (W)
VIN = 18V
70
2.0
VIN = 24V
0
IOUT (ADC)
-1.8
0.0
10.0
1.0
VIN = 12V
-1.2
1.0
VIN = 12V
0.1
0.0
VIN = 8V
-0.6
VIN = 8V
50
-2.4
0
0.1
Switching Frequency
0.18
VIN = 12V
0.15
400
VIN = 8V
VOUT Ripple (V)
500
Frequency (kHz)
10.0
0.20
600
VIN = 24V
300
VIN = 18V
200
0.13
VIN = 18V
0.10
0.08
VIN = 24V
0.05
100
0
0.03
0.0
0.5
1.0
1.5
IOUT (ADC)
2.0
2.5
0.00
3.0
VIN = 8V
VIN = 12V
0.0
0.5
IOUT = 1.5A
1.8
1.2
1
0.6
0.8
0
VOUT (%)
On-Time (ms)
1.2
0.6
-1.2
0.2
-1.8
9
12
15
18
Input Voltage (V)
1.5
IOUT (ADC)
2.0
2.5
3.0
21
24
IOUT = 1.5A
-0.6
0.4
6
1.0
Line Regulation
On-Time vs. VIN
0
1.0
IOUT (ADC)
Ripple vs. IOUT
700
1.4
VIN = 24V
0.6
PLOSS
VIN = 18V
60
VIN = 18V
1.2
VIN = 24V
80
Efficiency (%)
1.8
4.0
VIN = 8V
VOUT (%)
90
-2.4
6
9
12
15
18
Input Voltage (V)
21
24
SC410
Typical Characteristics (continued)
Characteristics are based on a circuit with VIN = 12V, L = 2.2µH (DCR = 35mΩ), COUT = 66µF, VOUT = 3.3V, RTON = 90.9kΩ.
Transient Response
Power Save
IOUT = 3A to 0A
IOUT = 0A
(20mV/div)
(50mV/div)
(10V/div)
(10V/div)
Time (100µ������
s�����
/div)
Time (10µ������
s�����
/div)
Shutdown
CCM
IOUT = 1.5A
IOUT = 1.5A
(5V/div)
(5V/div)
(20mV/div)
(1V/div)
(10V/div)
(10V/div)
Time (2µ������
s�����
/div)
Time (40µ������
s�����
/div)
Start-up
Start-up
IOUT = 0A
IOUT = 1.5A
(5V/div)
(5V/div)
(5V/div)
(5V/div)
(1V/div)
(1V/div)
(10V/div)
(10V/div)
Time (400µ������
s�����
/div)
Time (400µ������
s�����
/div)
SC410
Typical Characteristics (continued)
Characteristics are based on a circuit with VIN = 12V, RTON = 90.9kΩ.
Efficiency — Power Loss (5 VOUT)
Efficiency — Power Loss (3.3 VOUT)
4
90
80
3
70
2
60
50
PLOSS
0.001
0.01
0.1
IOUT (ADC)
1
10
VOUT = 5V, L= 4.7µH (16.2mΩ), CC = 220pF, COUT = 44µF
5
Efficiency
4
80
3
70
2
1
60
0
50
0.001
1
PLOSS
0.01
0.1
IOUT (ADC)
1
PLOSS (W)
Efficiency
100
Efficiency (%)
Efficiency (%)
90
5
PLOSS (W)
VOUT = 3.3V, L= 3.3µH (28mΩ), CC = 270pF, COUT = 66µF
100
10
0
Pin Descriptions
Pin #
Pin Name
Pin Function
1
BST
Bootstrap pin — A capacitor is connected between BST and LX to develop the floating voltage for the
high-side gate drive.
2
VIN
Power input supply voltage
3
LX
Switching (phase) node
4
PGND
5
PGOOD
6
FB
Feedback input for switching regulator — Connect to an external resistor divider from the output to program the output voltage.
7
EN
Enable input for switching regulator —Pull EN high to enable the part with ultrasonic power save mode enabled. Connect to AGND to disable the switching regulator. A voltage divider can be added between VIN and
AGND pins for input UVLO functionality.
8
TON
9
AGND
10
LDO
Output for the internal LDO and internal connection to the bias node — Decoupling capacitors are required
to AGND and PGND regardless of the use of the LDO for external loads.
PAD
Thermal pad for heatsinking purposes. (Not connected internally) Connect to AGND plane using multiple
vias.
Power ground
Open-drain power good indicator — High impedance indicates power is good. An external pull-up
resistor is required.
On-time set input — Set the on-time by connecting a series resistor to AGND.
Analog Ground.
10
SC410
Block Diagram
AGND
9
PGOOD
EN
BST
5
7
1
LDO
LDO
FB
Reference
Control and Status
2
VIN
3
LX
4
PGND
Soft Start
LX
FB
On-Time
Generator
6
Gate Drive
Control
LDO
FB Comparator
TON
8
Zero Cross Detector
RILIM
VIN
Valley Current Limit
ILIM
5V LDO
LDO
10
LDO
11
SC410
Applications Information
Synchronous Buck Converter
The SC410 is a step down synchronous buck DC-DC regulator. The device is capable of 3A operation at very high
efficiency in a tiny 3 x 3-10 pin package. The programmable operating frequency range of 200kHz – 1MHz enables
the user to optimize the design for minimum board space
and optimum efficiency.
The buck regulator employs pseudo-fixed frequency
adaptive on-time control. This control method allows fast
transient response thereby lowering the size of the power
components used in the system.
Input Voltage Range
The SC410 can operate with a wide input voltage ranging
from 5.5V to 24V. The internal LDO generates a fixed 5V
output that provides power for the bias of the SC410. The
LDO can also provide additional power to an external load.
Psuedo-fixed Frequency Adaptive On-time Control
The PWM control method used by the SC410 is pseudofixed frequency, adaptive on-time, as shown in Figure 1.
The ripple voltage generated at the output capacitor ESR
is divided down by the feedback resistor network and
used as a PWM ramp signal. The ripple seen at the FB pin
is used to trigger the on-time of the controller.
TON
VIN
VLX
CIN
Q1
VFB
VLX
VOUT
L
Q2
FB Threshold
ESR
+
FB
COUT
output voltage value and VIN. The period is proportional
to output voltage and inversely proportional to input
voltage. The value of the output voltage is obtained by
filtering the voltage seen on the LX pin.
With this adaptive on-time design, the device automatically anticipates the on-time needed to regulate VOUT for
the present VIN condition and at the selected frequency.
The advantages of adaptive on-time control are:
•
•
•
•
•
Predictable operating frequency during CCM
compared to other variable frequency
methods.
Reduced component count by eliminating the
error amplifier and compensation
components.
Reduced component count by removing the
need to sense and control inductor current.
Fast transient response — the response time is
controlled by a fast comparator instead of a
typically slow error amplifier.
Reduced output capacitance due to fast transient response
One-Shot Timer and Operating Frequency
The one-shot timer operates as shown in Figure 2. The
feedback comparator output goes high when VFB is less
than the internal 750mV reference. This feeds into the
gate drive and turns on the high-side MOSFET, and also
starts the one-shot timer. The one-shot timer uses an
internal comparator, timing capacitor, and a low pass
filter (LPF) which regenerates VOUT from LX. One comparator input is connected to the filtered LX voltage, the other
input is connected to the capacitor. When the on-time
begins, the internal capacitor charges from zero volts
through a current which is proportional to VIN. When the
capacitor voltage reaches VOUT, the on-time is completed
and the high-side MOSFET turns off.
Figure 1 — PWM Control Method, VOUT Ripple
The adaptive on-time is determined by an internal oneshot timer. When the one-shot is triggered by the feedback ripple, the device sends a single on-time pulse to the
high-side MOSFET. The pulse period is determined by the
12
SC410
Applications Information (continued)
FB
-
Ref.
PWM
+
VIN
S
R
VLX_FILTER
One-Shot
Timer
VIN
Q
Hi-side
and
Lo-side
Gate
Drivers
Q1
VOUT
VLX
Q2
L
VOUT Voltage Selection
The switcher output voltage is regulated by comparing
VOUT as seen through a resistor divider at the FB pin to the
internal 750mV reference voltage, see Figure 3.
FB
ESR
COUT
RTON
VLX_FILTER
LPF
VOUT
+
R1
To FB pin
R2
Time = K x (VOUT/VIN)
Figure 2 — On-Time Generation
This method automatically produces an on-time that is
proportional to VOUT and inversely proportional to VIN.
Under steady-state operating conditions in continuous
conduction mode, the switching frequency can be determined from the on-time by the following equation.
fSW
VOUT
t ON u VIN
The SC410 uses an external resistor to set the on-time
which indirectly sets the frequency. The on-time can be
programmed to provide operating frequencies from
200kHz to 1MHz using a resistor between the TON pin
and ground. The resistor value is selected by the following equation.
R TON
§
V
1
¨¨
400: u IN
25pF
f
V
u
SW
OUT
©
·
¸¸ u 1.2
¹
The maximum RTON value allowed is shown by the following equation.
RTON _ MAX
VIN _ MIN
10 u 1.5PA
Immediately after the on-time, the DL (the drive
signal for the low side FET) output drives high to
turn on the low-side MOSFET. DL has a minimum
high time of ~320ns, after which DL continues to
stay high until one of the following occurs:
•
•
VFB falls below the 750mV reference
The zero cross detector senses that the voltage
on the LX node is below ground. PSAVE is activated 8 periods after the zero cross is detected.
Figure 3 — Output Voltage Selection
Note that this control method regulates the valley of the
output ripple voltage, not the DC value. The DC output
voltage VOUT is offset by the output ripple according to
the following equation.
VOUT
§ R · §V
·
0.75 u ¨¨1 1 ¸¸ ¨ RIPPLE ¸
© R2 ¹ © 2 ¹
Enable Input
The EN input is used to enable or disable the switching
regulator. When EN is low (grounded), the switching regulator and LDO are disabled and the SC410 is in its lowest
power state. When disabled, the output power switches
are tri-stated. When EN is higher than 0.8V, the internal
LDO will be activated. The switching regulator remains off
until the voltage at the EN pin exceeds 1.5V.
The EN pin can be used for implementing UVLO for the
input voltage by configuring a voltage divider from VIN to
EN to PGND.
Continuous Mode Operation
The SC410 operates in CCM (Continuous Conduction
Mode) at larger load currents when the load is greater
than or equal to half of the inductor ripple current (Figure
4). In this mode one of the power MOSFETs is always on,
with no intentional dead time other than to avoid crossconduction. This mode of operation results in uniform
frequency.
13
SC410
Applications Information (continued)
FB Ripple
Voltage (VFB)
Minimum fSW ~ 25kHz
FB threshold
(750mV)
FB Ripple
Voltage
(VFB)
FB threshold
(750mV)
DC Load Current
Inductor
Current
(0A)
Inductor
Current
On-time
(TON)
DH on-time is triggered when
VFB reaches the FB Threshold.
On-time
(TON)
DH On-Time is triggered when
VFB reaches the FB Threshold
DH
DH
40µsec time-out
DL
DL
DL drives high when on-time is completed.
DL remains high until VFB falls to the FB threshold.
Figure 4 — Continuous Mode Operation
Ultrasonic Power Save Operation
The SC410 provides ultrasonic power save operation at
light loads, with the minimum operating frequency fixed
at 22kHz. This is accomplished using an internal timer that
monitors the time between consecutive high-side gate
pulses. If the time exceeds 40µs, DL drives high to turn the
low-side MOSFET on. This draws current from VOUT through
the inductor, forcing both VOUT and VFB to fall. When VFB
drops to the 750mV threshold, the next DH on-time is triggered. After the on-time is completed the high-side
MOSFET is turned off and the low-side MOSFET turns on.
The low-side MOSFET remains on until the inductor
current ramps down to zero, at which point the low-side
MOSFET is turned off.
Because the on-times are forced to occur at intervals no
greater than 40µs, the frequency will not fall below
~22kHz. Figure 5 shows ultrasonic power save operation.
After the 40µsec time-out, DL drives high if VFB
has not reached the FB threshold.
Figure 5 — Ultrasonic Power Save Operation
Smart Power Save Protection
Active loads may leak current from a higher voltage into
the switcher output. Under light load conditions with
power save enabled, this can force VOUT to slowly rise and
reach the over-voltage threshold, resulting in a hard shutdown. Smart power save prevents this condition. When
the FB voltage exceeds 10% above nominal (exceeds
825mV), the device immediately disables power-save,
and DL drives high to turn on the low-side MOSFET. This
draws current from VOUT through the inductor and causes
VOUT to fall. When VFB drops back to the 750mV trip point,
a normal TON switching cycle begins. This method prevents a hard OVP shutdown and also cycles energy from
VOUT back to VIN. Figure 6 shows typical waveforms for the
smart power save feature.
14
SC410
Applications Information (continued)
VOUT drifts up to due to leakage
current flowing into COUT
Smart Power Save
Threshold (825mV)
VOUT discharges via inductor
and low-side MOSFET
Normal VOUT ripple
FB
threshold
DH and DL off
High-side
Drive (DH)
In the SC410, the valley current limit is set to 3A. This results
in a peak inductor current of 3A plus the peak-to-peak
ripple current. In this situation, the average (load) current
through the inductor is 3A plus one-half the peak-to-peak
ripple current.
The internal 10μA current source is temperature compensated at 2500ppm in order to provide tracking with the
RDSON.
Single DH on-time pulse
after DL turn-off
Low-side
Drive (DL)
Peak Inductor Current
Normal DL pulse after
DH on-time pulse
DL turns on when Smart
PSAVE threshold is reached
DL turns off when FB
threshold is reached
Figure 6 — Smart Power Save
Current Limit Protection
Inductor Current
The current limiting is accomplished by using the RDSON of
the lower MOSFET for current sensing. The current limit is
set by an internal resistor RILIM. The resistor connects from
an ILIM node to the LX node which is also the drain of the
low-side MOSFET. When the low-side MOSFET is on, an
internal ~10μA current flows from the ILIM Node and
through the RILIM resistor, creating a voltage drop across the
resistor. While the low-side MOSFET is on, the inductor
current flows through it and creates a voltage across the
RDSON. The voltage across the MOSFET is negative with
respect to ground. If this MOSFET voltage drop exceeds the
voltage across RILIM, the voltage at the ILIM node will be
negative and current limit will activate. The current limit
then keeps the low-side MOSFET on and will not allow
another high-side on-time, until the current in the low-side
MOSFET reduces enough to bring the ILIM voltage back up
to zero. This method regulates the inductor valley current
at the level shown by ILIM in Figure 7.
IPEAK
ILOAD
ILIM
Time
The peak current through the inductor and switching FETs
must be less than 5A. The only way to meet this requirement is to select the switching frequency and inductor
value such that the peak inductor current is less than or
equal to 5A when the trough of the inductor current is
3A.
Soft start of PWM Regulator
Soft start is achieved in the PWM regulator by using an
internal voltage ramp as the reference for the FB comparator. The voltage ramp is generated using an internal
charge pump which drives the reference from zero to
750mV in ~1.8mV increments, using an internal ~500kHz
oscillator. When the ramp voltage reaches 750mV, the
ramp is ignored and the FB comparator switches over to
a fixed 750mV threshold. During soft start the output
voltage tracks the internal ramp, which limits the start-up
inrush current and provides a controlled soft start profile
for a wide range of applications. Typical soft start ramp
time is 850μs.
During soft start the regulator turns off the low-side
MOSFET on any cycle if the inductor current falls to zero.
This prevents negative inductor current, allowing the
device to start into a pre-biased output.
Power Good Output
The PGOOD (power good) output is an open-drain output
which requires a pull-up resistor. When the output voltage
is 10% below the nominal voltage, PGOOD is pulled low. It
is held low until the output voltage returns to the nominal
voltage. PGOOD is held low during soft start and activated
approximately 1ms after VOUT reaches regulation.
Figure 7 — Valley Current Limit
15
SC410
Applications Information (continued)
PGOOD will transition low if the VFB pin exceeds +20% of
nominal, which is also the over-voltage shutdown threshold (900mV).
Output Over-Voltage Protection
OVP (Over-Voltage Protection) becomes active as soon as
the device is enabled. The threshold is set at 750mV + 20%
(900mV). When VFB exceeds the OVP threshold, the output
goes to a tri-state with both FETs disabled and the part is
latched off. There is a 5μs delay built into the OVP detector
to prevent false transitions. PGOOD is also low after an
OVP event.
While the EN pin is above 0.5V, the LDO will be activated.
While the VLDO output voltage remains below 4V (80% of
the final LDO voltage), the LDO short-cicuit protection is
enabled and limits the current to about 35mA. After the
VLDO exceeds 4.0V (80% of VLDO Final), then the LDO operates in its normal regulation mode where the current is
limited to about 100mA (see Figure 8).
VLDO Final
Voltage regulating with
~100mA current limit
80% of VLDO Final
Output Under-Voltage Protection
When V FB falls to 75% of its nominal voltage (falls to
562.5mV) for eight consecutive clock cycles, the switcher
is shut off and the DH and DL drives are pulled low to turn
off the MOSFETs. The controller stays off until EN is toggled
or VIN is cycled.
Over-Temperature Protection
If the temperature rises to 145°C the device will latch off.
The device can be reactivated after the temperature is
reduced below 145°C by cycling the EN pin.
VLDO UVLO, and POR
UVLO (Under-Voltage Lock-Out) circuitry inhibits switching and tri-states the power FETs until VLDO rises above
4.0V. An internal POR (Power-On Reset) occurs when VLDO
exceeds 4.0V, which resets the fault latch and soft start
counter to begin the soft start cycle. The SC410 then
begins a soft start cycle. The PWM will shut off if VLDO falls
below 3.7V.
Internal LDO Regulator
The SC410 has an internal regulator that supplies the bias
voltage for the PWM controller. This LDO can also supply
an additional external current for an external load through
the LDO pin.
When activated, the LDO checks the status of the
following signals to ensure proper operation can be
maintained.
1. EN pin
2. VLDO output voltage
3. VIN input voltage
Sort-circuit Protection @ ~35mA
Figure 8 — LDO Start-Up
Design Procedure
When designing a switch mode supply the input voltage
range, load current, switching frequency, and inductor
ripple current must be specified.
The maximum input voltage (VINMAX) is the highest specified input voltage. The minimum input voltage ( VINMIN) is
determined by the lowest input voltage after evaluating
the voltage drops due to connectors, fuses, switches, and
PCB traces.
The following parameters define the design.
•
•
•
•
Nominal output voltage (VOUT )
Static or DC output tolerance
Transient response
Maximum load current (IOUT )
The two values of load current to evaluate are continuous
load current and peak load current. Continuous load
current relates to thermal stresses which drive the selection of the inductor and input capacitors. Peak load current
determines instantaneous component stresses and filtering requirements such as inductor saturation, output
capacitors, and design of the current limit circuit.
16
SC410
Applications Information (continued)
The following values are used in this design example.
•
•
•
•
VIN = 12V + 10%
VOUT = 3.3V + 4%
fSW = 500kHz
Load = 3A maximum
Frequency Selection
Selection of the switching frequency requires making a
trade-off between the size and cost of the external filter
components (inductor and output capacitor) and the
power conversion efficiency.
The desired switching frequency is 500kHz which results
from using components selected for optimum size and
cost.
A resistor (RTON) is used to program the on-time (indirectly
setting the frequency) using the following equation.
R TON
§
V
1
¨¨
400: u IN
VOUT
© 25pF u fSW
·
¸¸ u 1.2
¹
To select RTON, use the maximum value for VIN, and for TON
use the value associated with maximum VIN.
t ON
V OUT
V INMAX u f SW
tON = 500 ns at 13.2VIN, 3.3VOUT, 500kHz
Substituting for RTON results in the following solution.
RTON = 78.5kΩ, use RTON = 78.7kΩ
save mode when the load current decreases to 1/2 of the
ripple current. For example, if ripple current is 2A then
power-save operation will typically start for loads less than
1A. If ripple current is set at 40% of maximum load current,
then power-save will start for loads less than 20% of
maximum current.
During the DH on-time, voltage across the inductor is
(VIN - VOUT ). The equation for determining inductance is
shown next.
L
( VIN VOUT ) u t ON
IRIPPLE
Example
In this example, the inductor ripple current is set equal to
75% of the maximum load current. Therefore ripple
current will be 75% x 3A or 2.25A. To find the minimum
inductance needed, use the VIN and TON values that correspond to VINMAX.
L
(13.2V 3.3 V ) u 501ns
2.25 A
2.204PH
A standard value of 2.2µH is selected. This gives a
maximum IRIPPLE of 2.53A. The peak ripple can be calculated
by the equation, below where LTOL is assumed to be an
inductor tolerance of 20%.
IRIPPLE_PEAK = IRIPPLE_MAX x (1 + LTOL) = 2.705A
Note that the inductor must be rated for the maximum DC
load current plus 1/2 of the ripple current.
Now, tON = 501ns given that RTON = 78.7kΩ.
Inductor Selection
In order to determine the inductance, the ripple current
must first be defined. Low inductor values result in smaller
size but create higher ripple current which can reduce
efficiency. Higher inductor values will reduce the ripple
current/voltage and for a given DC resistance are more
efficient. However, larger inductance translates directly
into larger packages and higher cost. Cost, size, output
ripple, and efficiency are all used in the selection process.
The ripple current under minimum VIN conditions is also
checked using the following equations.
The ripple current will also set the boundary for powersave operation. The switching will typically enter power-
ILSAT_MIN = IRIPPLE_PEAK X 0.5 + IOUT = 4.353A
t ON _ VINMIN
IRIPPLE
25pF u R TON u VOUT
10ns
VINMIN
611ns
( VIN VOUT ) u t ON
L
IRIPPLE _ VINMIN
(10.8 V 3.3 V ) u 612ns
2.2PH
2.08 A
17
SC410
Applications Information (continued)
Capacitor Selection
The output capacitors are chosen based on required ESR
and capacitance. The maximum ESR requirement is controlled by the output ripple requirement and the DC tolerance. The output voltage has a DC value that is equal to
the valley of the output ripple plus 1/2 of the peak-to-peak
ripple. Change in the output ripple voltage will lead to a
change in DC voltage at the output.
The design goal is for the output voltage regulation to be
±4% under static conditions. The internal 750mV reference
tolerance is 1%. Assuming a 1% tolerance from the FB resistor divider, this allows 2% tolerance due to VOUT ripple. Since
this 2% error comes from 1/2 of the ripple voltage, the
allowable ripple is 4%, or 132mV for a 3.3V output.
The maximum ripple current of 2.7A creates a ripple
voltage across the ESR. The maximum ESR value allowed
is shown by the following equations.
ESRMAX
2 u VRIPPLE
IRIPPLEMAX
132mV
2.705 A
1
§
·2
L1 L TOL u ¨ IOUT u IRIPPLE _ PEAK ¸
2
©
¹
2
1
§
·2
2.2PH 1 20%¨ 3 A u 2.705 A ¸
2
©
¹
2
ILPK = IMAX + 1/2 x IRIPPLEMAX
ILPK = 3A + 1/2 x 2.7A = 4.353A
3.432V 3.3V 2
dlLOAD
dt
IMAX = maximum load release = 3A
COUT
ILPK u
Lu 1 L TOL u
ILPK
I
MAX u dt
VOUT d lLOAD
2VPK VOUT Example
dlLOAD
dt
2A
1Ps
This causes the output current to move from 3A to 0A in
4.8µs, giving the minimum output capacitance requirement shown in the following equation.
2
Assuming a peak voltage VPEAK of 1.150 (132mV rise upon
load release), and a 6A load release, the required capacitance is shown by the next equation.
COUTMIN
The output capacitance is chosen to meet transient
requirements. A worst-case load release, from maximum
load to no load at the exact moment when inductor
current is at the peak, determines the required capacitance. If the load release is instantaneous (load changes
from maximum to zero in < 1µs), the output capacitor
must absorb all the inductor’s stored energy. This will
cause a peak voltage on the capacitor according to the
following equation.
VPEAK VOUT The following can be used to calculate the needed capacitance for a given dILOAD/dt. Peak inductor current is shown
by the next equation.
Rate of change of Load Current
ESRMAX = 48.8 mΩ
COUTMIN
If the load release is relatively slow, the output capacitance
can be reduced. At heavy loads during normal switching,
when the FB pin is above the 750mV reference, the DL
output is high and the low-side MOSFET is on. During this
time, the voltage across the inductor is approximately VOUT.
This causes a down-slope or falling di/dt in the inductor. If
the load di/dt is not much faster than the di/dt in the
inductor, then the inductor current will tend to track the
falling load current. This will reduce the excess inductive
energy that must be absorbed by the output capacitor,
therefore a smaller capacitance can be used.
COUT
4.353 A u
4.353 A 3 A
u 1Ps
3 .3 V
2A
23.432 V 3.3 V 2.2PH1 20 % u
COUT = 33µF
Note that COUT is much smaller in this example, 33µF compared to 56µF based on a worst-case load release. To meet
the worst case design criteria of minimum 56µF, select
three capacitors rated at 22µF and 15mΩ ESR.
COUTMIN = 56µF
18
SC410
Applications Information (continued)
Stability Considerations
Unstable operation is possible with adaptive on-time controllers, and usually takes the form of double-pulsing or
ESR loop instability.
Double-pulsing occurs due to switching noise seen at the
FB input or because the FB ripple voltage is too low. This
causes the FB comparator to trigger prematurely after the
minimum off-time has expired. In extreme cases the noise
can cause three or more successive on-times. Doublepulsing will result in higher ripple voltage at the output,
but in most applications it will not affect operation. This
form of instability can usually be avoided by providing the
FB pin with a smooth, clean ripple signal that is at least
10mVp-p, which may dictate the need to increase the ESR
of the output capacitors. It is also imperative to provide a
proper PCB layout.
An alternate method to eliminate doubling-pulsing is to
add a small (~ 10pF) capacitor across the upper feedback
resistor, as shown in Figure 9. This capacitor should be left
unpopulated unless it can be confirmed that doublepulsing exists. Adding the CTOP capacitor will couple more
ripple into FB to help eliminate the problem. An optional
connection on the PCB should be provided for this
capacitor.
ESR Requirements
A minimum ESR is required for two reasons. The first
reason is to generate enough output ripple voltage to
provide 10mVp-p at the FB pin (after the resistor divider)
to avoid double-pulsing.
The second reason is to prevent instability due to insufficient ESR. The on-time control regulates the valley of the
output ripple voltage. This ripple voltage is the sum of the
two voltages. One is the ripple generated by the ESR, the
other is the ripple due to capacitive charging and discharging during the switching cycle. For most applications, the total output ripple voltage is dominated by the
output capacitors, typically SP or POSCAP devices. For
stability the ESR zero of the output capacitor should be
lower than approximately one-third the switching frequency. The formula for minimum ESR is shown by the
following equation.
ESR MIN
3
2 u S u C OUT u f sw
Using Ceramic Output Capacitors
CTOP
VOUT
One simple method of solving this problem is to add trace
resistance in the high current output path. A side effect of
adding trace resistance is a decrease in load regulation.
To FB pin
R1
R2
Figure 9 — Capacitor Coupling to FB Pin
When applications use ceramic output capacitors, the ESR
is normally too small to meet the previously stated ESR
criteria. In these applications it is necessary to add a small
signal injection network as shown in Figure 10. In this
network RL and CL filter the LX switching waveform to
generate an in-phase ripple voltage comparable to the
ripple seen on higher ESR capacitors. CC is a coupling
capacitor used to AC couple the generated ripple onto the
FB pin.
ESR loop instability is caused by insufficient ESR. The
details of this stability issue are discussed in the ESR
Requirements section. The best method for checking stability is to apply a zero-to-full load transient and observe
the output voltage ripple envelope for overshoot and
ringing. Ringing for more than one cycle after the initial
step is an indication that the ESR should be increased.
19
SC410
Applications Information (continued)
Output Voltage Dropout
L
Highside
RL
CL
R1
CC
Lowside
FB
pin
COUT
R2
Figure 10 — Signal Injection Circuit
The values of RL, CL, and CC are dependent on the conditions of the specific application such as VIN, VOUT, fSW and
IOUT.
Select a value for CL, like 10nF. Using CL, calculate RL as
shown in the following equation:
RL
L
CL u DCR
Where L is the inductor value and DCR is the resistance of
the inductor.
The value for CC can be between CC_MIN and CC_MAX.
CC _ MIN
t ON
REQ
CC _ MAX
T
REQ
Where T = 1/fSW and REQ is represented by the following
equation.
REQ
RBOTTOM u
RTOP
RBOTTOM RTOP
It is beneficial to use the smallest value of CC that provides
stability and enough voltage ripple at feedback. Larger
values of CC may negatively affect the load regulation
performance.
The output voltage adjustable range for continuous-conduction operation is limited by the fixed 320ns (typical)
minimum off-time. When working with low input voltages, the duty-factor limit must be calculated using worstcase values for on and off times. The duty-factor limitation
is shown by the next equation.
DUTY
t ON(MIN)
t ON(MIN) t OFF(MAX )
The inductor resistance and MOSFET on-state voltage
drops must be included when performing worst-case
dropout duty-factor calculations.
System DC Accuracy — VOUT Controller
Three factors affect VOUT accuracy: the trip point of the FB
error comparator, the ripple voltage variation with line
and load, and the external resistor tolerance. The error
comparator offset is trimmed so that under static conditions it trips when the feedback pin is 750mV, +1%.
The on-time pulse from the SC410 in the design example
is calculated to give a pseudo-fixed frequency of 500kHz.
Some frequency variation with line and load is expected.
This variation changes the output ripple voltage. Because
adaptive on-time converters regulate to the valley of the
output ripple, ½ of the output ripple appears as a DC regulation error.
To compensate for valley regulation, it may be desirable to
use passive droop. Take the feedback directly from the
output side of the inductor and place a small amount of
trace resistance between the inductor and output capacitor. This trace resistance should be optimized so that at
full load the output droops to near the lower regulation
limit. Passive droop minimizes the required output capacitance because the voltage excursions due to load steps
are reduced as seen at the load.
The use of 1% feedback resistors may result in up to an
additional 1% error. If tighter DC accuracy is required,
resistors with lower tolerances should be used.
20
SC410
Applications Information (continued)
The output inductor value may change with current. This
will change the output ripple and therefore will have a
minor effect on the DC output voltage. The output ESR
also affects the output ripple and thus has a minor effect
on the DC output voltage.
Switching Frequency Variation
The switching frequency will vary depending on line and
load conditions. The line variations are a result of fixed
propagation delays in the on-time one-shot, as well as
unavoidable delays in the power FET switching. As VIN
increases, these factors make the actual DH on-time
slightly longer than the ideal on-time. The net effect is
that frequency tends to fall slightly with increasing input
voltage.
The switching frequency also varies with load current as a
result of the power losses in the MOSFETs and the inductor. For a conventional PWM constant-frequency converter, as load increases the duty cycle also increases
slightly to compensate for IR and switching losses in the
MOSFETs and inductor. An adaptive on-time converter
must also compensate for the same losses by increasing
the effective duty cycle (more time is spent drawing
energy from VIN as losses increase). The on-time is essentially constant for a given VOUT and VIN combination, to
offset the losses the off-time will tend to reduce slightly as
load increases. The net effect is that switching frequency
increases slightly with increasing load.
21
SC410
Applications Information (continued)
PCB Layout Guidelines
The optimum layout for the SC410 is shown in Figure 11.
This layout shows an integrated FET buck regulator with a
maximum current of 3A. The total PCB area is approximately 19.1mm x 11.3mm.
Critical Layout Guidelines
The following critical layout guidelines must be followed
to ensure proper performance of the device.
•
•
•
•
•
•
IC Decoupling capacitors
PGND plane
AGND island
FB and other analog control signals
BST and LX
Capacitors and Current Loops
PGND Plane
PGND requires its own copper plane with no
other signal traces routed on it.
Copper planes, multiple vias, and wide traces are
needed to connect PGND to input capacitors,
output capacitors, and the PGND pins on the IC.
The PGND copper area between the input
capacitors, output capacitors, and PGND pins
must be as small as and as compact as possible
to reduce the area of the PCB that is exposed to
noise due to current flow on this node.
Connect PGND to AGND with a short trace or
0Ω resistor. This connection should be as close
to the IC as possible.
•
•
•
•
IC Decoupling Capacitors
A 0.1 μF capacitor must be located as close as
possible to the IC and directly connected to pins
10 (LDO) and 9 (AGND).
All other decoupling capacitors must be located
as close as possible to the IC.
•
•
LX connection
using a Via
AGND Island
AGND should have its own island of copper with
no other signal traces routed on this layer that
connects the AGND pins and pad of the IC to the
analog control components.
All of the components for the analog control circuitry should be located so that the connections
•
•
SC410
FB node
VESR node
PGND
Figure 11 — PCB Layout
22
SC410
Applications Information (continued)
•
to AGND are done by wide copper traces or vias
down to AGND.
Connect PGND to AGND with a short trace or 0Ω
resistor. This connection should be as close to
the IC as possible.
FB and Other Analog Control Signals
The connection from the V OUT power to the
analog control circuitry must be routed from the
output capacitors and located on a quiet layer.
The traces between VOUT and the analog control
circuitry (AGND, and FB pins) must be as short as
possible. The traces must also be routed away
from noise sources, such as BST, LX, VIN, and
PGND between the input capacitors, output
capacitors, and the IC.
The TON node must be as short as possible to
ensure the best accuracy for the on time.
The feedback components for the switcher need
to be as close to the FB pin of the IC as possible
to reduce the possibility of noise corrupting
these analog signals.
•
•
•
•
BST and LX
LX and BST are very noisy nodes and must be
carefully routed to minimized the PCB area that
is exposed to these signals.
The connections for the boost capacitor
between the IC and LX must be short and directly
connected to the LX (pin 3).
The LX node between the IC and the inductor
should be wide enough to handle the inductor
current and short enough to eliminate the possibility of LX noise corrupting other signals.
•
•
•
Capacitors and Current Loops
The current loops between the input capacitors,
the IC, the inductor, and the output capacitors
must be as close as possible to each other to
reduce IR drop across copper planes and traces.
All bypass and output capacitors must be connected as close as possible to their respective
pin on the IC.
•
•
23
SC410
Outline Drawing — MLPD-10 3x3
D
A
B
DIM
A
A1
A2
b
D
D1
E
E1
e
L
N
aaa
bbb
E
PIN 1
INDICATOR
(LASER MARK)
A
aaa C
1
.031
.039
.000
.002
(.008)
.008 .010 .012
.114 .118 .122
.087 .089 .091
.114 .118 .122
.057 .059 .061
.020 BSC
.018 .020 .022
10
.003
.004
0.80
1.00
0.00
0.05
(0.20)
0.20 0.25 0.30
2.90 3.00 3.10
2.20 2.25 2.30
2.90 3.00 3.10
1.45 1.50 1.55
0.50 BSC
0.45 0.50 0.55
10
0.08
0.10
SEATING
PLANE
C
A1
D1
DIMENSIONS
INCHES
MILLIMETERS
MIN NOM MAX MIN NOM MAX
A2
2
LxN
E/2
E1
N
e
D/2
bxN
bbb
C A B
NOTES:
1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES).
2. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS TERMINALS.
24
SC410
Land Pattern — MLPD-10 3x3
K
DIM
G
(C) H
Y
X
P
Z
DIMENSIONS
INCHES
MILLIMETERS
C
G
H
K
P
X
Y
Z
(.112)
.079
.059
.089
.020
.012
.033
.146
(2.85)
2.00
1.50
2.25
0.50
0.30
0.85
3.70
NOTES:
1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES).
2. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY.
CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR
COMPANY'S MANUFACTURING GUIDELINES ARE MET.
3. THERMAL VIAS IN THE LAND PATTERN OF THE EXPOSED PAD
SHALL BE CONNECTED TO A SYSTEM GROUND PLANE.
FAILURE TO DO SO MAY COMPROMISE THE THERMAL AND/OR
FUNCTIONAL PERFORMANCE OF THE DEVICE.
25
SC410
© Semtech 2011
All rights reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright
owner. The information presented in this document does not form part of any quotation or contract, is believed to be
accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights. Semtech assumes no responsibility or liability whatsoever for any failure or unexpected operation
resulting from misuse, neglect improper installation, repair or improper handling or unusual physical or electrical stress
including, but not limited to, exposure to parameters beyond the specified maximum ratings or operation outside the
specified range.
SEMTECH PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED OR WARRANTED TO BE SUITABLE FOR USE IN LIFESUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF SEMTECH PRODUCTS
IN SUCH APPLICATIONS IS UNDERSTOOD TO BE UNDERTAKEN SOLELY AT THE CUSTOMER’S OWN RISK. Should a customer
purchase or use Semtech products for any such unauthorized application, the customer shall indemnify and hold
Semtech and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs damages
and attorney fees which could arise.
Notice: All referenced brands, product names, service names and trademarks are the property of their respective
owners.
Contact Information
Semtech Corporation
Power Management Products Division
200 Flynn Road, Camarillo, CA 93012
Phone: (805) 498-2111 Fax: (805) 498-3804
www.semtech.com
26