LM43603 SIMPLE SWITCHER 3.5V to 36V 3A

Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
LM43603 SIMPLE SWITCHER® 3.5 V to 36 V 3 A Synchronous Step-Down Voltage
Converter
1 Features
3 Description
•
•
•
•
•
The LM43603 SIMPLE SWITCHER® regulator is an
easy to use synchronous step-down DC-DC
converter capable of driving up to 3 A of load current
from an input voltage ranging from 3.5 V to 36 V (42V
abs max). The LM43603 provides exceptional
efficiency, output accuracy and dropout voltage in a
very small solution size. An extended family is
available in 0.5 A ,1 A and 2 A load current options in
pin to pin compatible packages. Peak current mode
control is employed to achieve simple control loop
compensation and cycle-by-cycle current limiting.
Optional features such as programmable switching
frequency,
synchronization,
power-good
flag,
precision enable, internal soft-start, extendable softstart, and tracking provide a flexible and easy to use
platform for a wide range of applications.
Discontinuous conduction and automatic frequency
modulation at light loads improve light load efficiency.
The family requires few external components and pin
arrangement allows simple, optimum PCB layout.
Protection features include thermal shutdown, VCC
under-voltage lockout, cycle-by-cycle current limit,
and output short circuit protection. The LM43603
device is available in the HTSSOP / PWP 16 leaded
package (5.1mm x 6.6mm x 1.2mm). Pin to pin
compatible with LM43600, LM43601, LM43602,
LM46000, LM46001, LM46002.
27 µA Quiescent Current in Regulation
High Efficiency at Light Load (DCM and PFM)
Meets EN55022/CISPR 22 EMI standards
Integrated Synchronous Rectification
Adjustable Frequency Range: 200 kHz to 2.2 MHz
(500 kHz default)
Frequency Synchronization to External Clock
Internal Compensation
Stable with Almost Any Combination of Ceramic,
Polymer, Tantalum, and Aluminum Capacitors
Power-Good Flag
Soft-Start into a Pre-Biased Load
Internal Soft-Start: 4.1 ms
Extendable Soft-Start Time by External Capacitor
Output Voltage Tracking Capability
Precision Enable to a Program System UVLO
Output Short Circuit Protection with Hiccup Mode
Over Temperature Thermal Shutdown Protection
1
•
•
•
•
•
•
•
•
•
•
•
2 Applications
•
•
•
•
•
Industrial Power Supplies
Telecommunications Systems
Sub-AM Band Automotive
General Purpose Wide VIN Regulation
High Efficiency Point-Of-Load Regulation
Device Information
ORDER NUMBER
LM43603PWP
PACKAGE
BODY SIZE
HTSSOP (16)
5.1 mm x 6.6 mm
4 Simplified Schematic
L
VIN
CIN
ENABLE
CBOOT
CBIAS
SS/TRK
SYNC
AGND
80
COUT
CBOOT
BIAS
PGOOD
RT
VOUT
SW
LM43603
CFF
RFBT
FB
VCC
CVCC
RFBB
PGND
C001
Radiated EMI Emissions (dBµV/m)
VIN
LM43603PWPEVM Radiated Emission Graph
12VIN to 3.3VOUT, FS = 500 kHz, IOUT = 3A
Evaluation Board
70
EN 55022 Class B Limit
EN 55022 Class A Limit
60
50
40
30
20
10
0
0
200
400
600
Frequency (MHz)
800
1000
C001
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
Features ..................................................................
Applications ...........................................................
Description .............................................................
Simplified Schematic.............................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
1
2
3
4
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
4
4
4
5
5
6
7
8
Absolute Maximum Ratings ......................................
Handling Ratings.......................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Timing Requirements ................................................
Switching Characteristics ..........................................
Typical Characteristics ..............................................
Detailed Description ............................................ 14
8.1
8.2
8.3
8.4
9
Overview .................................................................
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
14
14
15
22
Applications and Implementation ...................... 24
9.1 Application Information............................................ 24
9.2 Typical Applications ................................................ 24
10 Power Supply Recommendations ..................... 39
11 Layout................................................................... 39
11.1 Layout Guidelines ................................................. 39
11.2 Layout Example .................................................... 42
12 Device and Documentation Support ................. 43
12.1 Trademarks ........................................................... 43
12.2 Electrostatic Discharge Caution ............................ 43
12.3 Glossary ................................................................ 43
13 Mechanical, Packaging, and Orderable
Information ........................................................... 43
5 Revision History
Changes from Original (April 2014) to Revision A
•
Page
Changed device from Product Preview to Production Data .................................................................................................. 1
Changes from Revision A (April 2014) to Revision B
Page
•
Changed Figure 33 into conducted EMI Curve .................................................................................................................... 13
•
Added Equation 25 ............................................................................................................................................................... 30
•
Added Equation 26 ............................................................................................................................................................... 30
•
Added Figure 73 to Figure 78. Application Performance Curves for VOUT = 5 V, Fs = 500 kHz. ........................................ 35
•
Changed Figure 86............................................................................................................................................................... 37
•
Changed Figure 87 .............................................................................................................................................................. 37
2
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
LM43603
www.ti.com
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
6 Pin Configuration and Functions
16-Pin HTSSOP (PWP)
Top View
SW
1
SW
2
16
15
PGND
PGND
CBOOT
VCC
3
4
14
VIN
13
BIAS
5
VIN
12
SYNC
EN
6
11
RT
PGOOD
SS/TRK
7
8
10
AGND
PAD
9
FB
Pin Functions
PIN
(1)
DESCRIPTION
NAME
NUMBER
TYPE (1)
SW
1,2
P
Switching output of the regulator. Internally connected to both power MOSFETs. Connect to
power inductor.
CBOOT
3
P
Boot-strap capacitor connection for high-side driver. Connect a high quality 470 nF capacitor
from CBOOT to SW.
VCC
4
P
Internal bias supply output for bypassing. Connect bypass capacitor from this pin to AGND.
Do not connect external loading to this pin. Never short this pin to ground during operation.
BIAS
5
P
Optional internal LDO supply input. To improve efficiency, it is recommended to tie to VOUT
when 3.3 V ≤ VOUT ≤ 28 V, or tie to an external 3.3 V or 5 V rail if available. When used,
place a bypass capacitor (1 to 10 µF) from this pin to ground. Tie to ground when not in use.
Do not float
SYNC
6
A
Clock input to synchronize switching action to an external clock. Use proper high speed
termination to prevent ringing. Connect to ground if not used. Do not float
RT
7
A
Connect a resistor RT from this pin to AGND to program switching frequency. Leave floating
for 500 kHz default switching frequency.
PGOOD
8
A
Open drain output for power-good flag. Use a 10 kΩ to 100 kΩ pull-up resistor to logic rail or
other DC voltage no higher than 12 V.
FB
9
A
Feedback sense input pin. Connect to the midpoint of feedback divider to set VOUT. Do not
short this pin to ground during operation.
AGND
10
G
Analog ground pin. Ground reference for internal references and logic. Connect to system
ground.
SS/TRK
11
A
Soft-start control pin. Leave floating for internal soft-start slew rate. Connect to a capacitor to
extend soft start time. Connect to external voltage ramp for tracking.
EN
12
A
Enable input to the internal LDO and regulator. High = ON and low = OFF. Connect to VIN,
or to VIN through resistor divider,or to an external voltage or logic source. Do not float.
VIN
13,14
P
Supply input pins to internal LDO and high side power FET. Connect to power supply and
bypass capacitors CIN. Path from VIN pin to high frequency bypass CIN and PGND must be
as short as possible.
PGND
15,16
G
Power ground pins, connected internally to the low side power FET. Connect to system
ground, PAD, AGND, ground pins of CIN and COUT. Path to CIN must be as short as
possible.
PAD
-
-
Low impedance connection to AGND. Connect to PGND on PCB . Major heat dissipation
path of the die. Must be used for heat sinking to ground plane on PCB.
P = Power, G = Ground, A = Analog
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
3
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
www.ti.com
7 Specifications
7.1 Absolute Maximum Ratings (1)
Over operating free-air temperature range (unless otherwise noted)
Input Voltages
Output Voltages
(1)
(2)
PARAMETER
MIN
MAX
VIN to PGND
-0.3
42 (2)
UNIT
EN to PGND
-0.3
VIN+0.3
FB, RT, SS/TRK to AGND
-0.3
3.6
PGOOD to AGND
-0.3
15
SYNC to AGND
-0.3
5.5
BIAS to AGND
-0.3
30
AGND to PGND
-0.3
0.3
SW to PGND
-0.3
VIN+0.3
SW to PGND less than 10ns Transients
-3.5
42
CBOOT to SW
-0.3
5.5
VCC to AGND
-0.3
3.6
V
V
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
At maximum duty cycle of 0.01%
7.2 Handling Ratings
PARAMETER
DEFINITION
MIN
MAX
UNIT
Tstg
Storage temperature range
-65
+150
°C
VESD
(1)
(2)
(1) (2)
HBM Human body model
1.0
CDM Charge device model
0.5
kV
Electrostatic discharge (ESD) to measure device sensitivity/immunity to damage caused by assembly line electrostatic discharges into
the device.
ESD testing is performed according to the respective JESD22 JEDEC standard.
7.3 Recommended Operating Conditions (1)
Over operating free-air temperature range (unless otherwise noted)
Input Voltages
PARAMETER
MIN
MAX
VIN to PGND
3.5
36
EN
-0.3
VIN
FB
-0.3
1.1
PGOOD
-0.3
12
BIAS input not used
-0.3
0.3
BIAS input used
3.3
28 or VIN
UNIT
V
(2)
AGND to PGND
-0.1
0.1
Output Voltage
VOUT
1.0
28
V
Output Current
IOUT
0
3
A
Temperature
Operating junction temperature range, TJ
-40
+125
°C
(1)
(2)
4
Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits.
For guaranteed specifications, see Electrical Characteristics.
Whichever is lower.
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
LM43603
www.ti.com
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
7.4 Thermal Information
THERMAL METRIC
HTSSOP
(16 PINS)
(1) (2)
RθJA
Junction-to-ambient thermal resistance
RθJC (Top)
Junction-to-case (top) thermal resistance
24.3
RθJB
Junction-to-board thermal resistance
19.9
ψJT
Junction-to-top characterization parameter
0.7
ψJB
Junction-to-board characterization parameter
19.7
RθJC(bot)
Junction-to-case (bottom) thermal resistance
1.7
(1)
(2)
(3)
38.9
UNIT
(3)
°C/W
The package thermal impedance is calculated in accordance with JESD 51-7;
Thermal Resistances were simulated on a 4 layer, JEDEC board.
See Figure 98 for θJA vs Copper Area Curve
7.5 Electrical Characteristics
Limits apply over the recommended operating junction temperature (TJ) range of -40°C to +125°C, unless otherwise stated.
Minimum and Maximum limits are specified through test, design or statistical correlation. Typical values represent the most
likely parametric norm at TJ = 25°C, and are provided for reference purposes only. Unless otherwise stated, the following
conditions apply: VIN = 12 V, VOUT = 3.3 V, FS = 500 kHz.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY VOLTAGE (VIN PIN)
VIN-MIN-ST
Minimum input voltage for startup
3.8
V
ISHDN
Shutdown quiescent current
VEN = 0 V
1.2
3.1
µA
Operating quiescent current (nonswitching) from VIN
VEN = 3.3 V
VFB = 1.5 V
VBIAS = 3.4 V external
5.0
10
µA
Operating quiescent current (nonswitching) from external VBIAS
VEN = 3.3 V
VFB = 1.5 V
VBIAS = 3.4 V external
85
130
µA
Operating quiescent current (switching)
VEN = 3.3 V
IOUT = 0 A
RT = open
VBIAS = VOUT = 3.3 V
RFBT = 1.0 Meg
27
IQ-NONSW
IBIAS-NONSW
IQ-SW
µA
ENABLE (EN PIN)
VEN-VCC-H
Voltage level to enable the internal LDO
output VCC
VEN-VCC-L
Voltage level to disable the internal LDO
VENABLE low level
output VCC
VEN-VOUT-H
Precision enable level for switching and
regulator output: VOUT
VENABLE high level
VEN-VOUT-HYS
Hysteresis voltage between VOUT
precision enable and disable thresholds
VENABLE hysteresis
ILKG-EN
Enable input leakage current
VEN = 3.3 V
0.8
3.28
VENABLE high level
1.2
2.00
V
2.2
0.525
V
2.42
V
-290
mV
1.75
µA
INTERNAL LDO (VCC and BIAS PINS)
VCC
Internal LDO output voltage VCC
VIN ≥ 3.8 V
VCC-UVLO
Under voltage lock out (UVLO)
thresholds for VCC
VCC rising threshold
Hysteresis voltage between rising and
falling thresholds
-520
Internal LDO input change over
threshold to BIAS
VBIAS rising threshold
2.94
VBIAS-ON
Hysteresis voltage between rising and
falling thresholds
V
3.1
V
mV
3.15
-75
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
V
mV
5
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
www.ti.com
Electrical Characteristics (continued)
Limits apply over the recommended operating junction temperature (TJ) range of -40°C to +125°C, unless otherwise stated.
Minimum and Maximum limits are specified through test, design or statistical correlation. Typical values represent the most
likely parametric norm at TJ = 25°C, and are provided for reference purposes only. Unless otherwise stated, the following
conditions apply: VIN = 12 V, VOUT = 3.3 V, FS = 500 kHz.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
TJ = 25 ºC
1.004
1.011
1.018
TJ = -40 ºC to 85 ºC
0.994
1.011
1.026
TJ = -40 ºC to 125 ºC
0.994
UNIT
VOLTAGE REFERENCE (FB PIN)
VFB
Feedback voltage
ILKG-FB
Input leakage current at FB pin
V
1.011
1.030
FB = 1.011 V
0.2
65
Shutdown threshold
160
ºC
Recovery threshold
150
ºC
nA
THERMAL SHUTDOWN
TSD
(1)
Thermal shutdown
CURRENT LIMIT AND HICCUP
IHS-LIMIT
Peak inductor current limit
4.4
5.5
6.4
A
ILS-LIMIT
Inductor current valley limit
2.6
3.0
3.3
A
1.25
2.0
2.75
µA
SOFT START (SS/TRK PIN)
ISSC
Soft-start charge current
RSSD
Soft-start discharge resistance
UVLO, TSD, OCP, or EN = 0 V
18
kΩ
POWER GOOD (PGOOD PIN)
VPGOOD-HIGH
Power-good flag over voltage tripping
threshold
% of FB voltage
VPGOOD-LOW
Power-good flag under voltage tripping
threshold
% of FB voltage
VPGOOD-HYS
Power-good flag recovery hysteresis
% of FB voltage
RPGOOD
PGOOD pin pull down resistance when
power bad
VEN = 3.3 V
40
125
VEN = 0 V
60
150
RDS-ON-HS
High-side MOSFET ON-resistance
IOUT = 1 A
VBIAS = VOUT = 3.3 V
120
mΩ
RDS-ON-LS
Low-side MOSFET ON-resistance
IOUT = 1 A
VBIAS = VOUT = 3.3 V
65
mΩ
MOSFETS
(1)
(2)
110%
77%
113%
88%
6%
Ω
(2)
Ensured by design
Measured at pins
7.6 Timing Requirements
MIN
TYP
MAX
UNIT
CURRENT LIMIT AND HICCUP
NOC
Hiccup wait cycles when LS current limit tripped
32
Cycles
TOC
Hiccup retry delay time
5.5
ms
4.1
ms
TPGOOD-RISE Power-good flag rising transition deglitch delay
220
µs
TPGOOD-FALL Power-good flag falling transition deglitch delay
220
µs
SOFT START (SS/TRK PIN)
TSS
Internal soft-start time when SS pin open circuit
POWER GOOD (PGOOD PIN)
6
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
LM43603
www.ti.com
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
7.7 Switching Characteristics
Limits apply over the recommended operating junction temperature (TJ) range of -40°C to +125°C, unless otherwise stated.
Minimum and Maximum limits are specified through test, design or statistical correlation. Typical values represent the most
likely parametric norm at TJ = 25°C, and are provided for reference purposes only. Unless otherwise stated, the following
conditions apply: VIN = 12 V, VOUT = 3.3 V, FS = 500 kHz.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SW (SW PIN)
tON-MIN (1)
Minimum high side MOSFET ON
time
125
165
ns
tOFF-MIN (1)
Minimum high side MOSFET OFF
time
200
250
ns
500
580
kHz
OSCILLATOR (SW and SYNC PINS)
FOSC-
Oscillator default frequency
RT pin open circuit
425
DEFAULT
Minimum adjustable frequency
FADJ
Maximum adjustable frequency
With 1% resistors at RT pin
Frequency adjust accuracy
200
kHz
2200
kHz
10%
VSYNC-HIGH Sync clock high level threshold
2
V
VSYNC-LOW
Sync clock low level threshold
DSYNC-MAX
Sync clock maximum duty cycle
90%
DSYNC-MIN
Sync clock minimum duty cycle
10%
TSYNC-MIN
Mininum sync clock ON and OFF
time
(1)
0.4
80
V
ns
Ensured by design
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
7
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
www.ti.com
7.8 Typical Characteristics
100
100
90
90
80
80
Efficiency (%)
Efficiency (%)
Unless otherwise specified, VIN = 12 V, VOUT = 3.3 V, FS = 500 kHz, L = 6.8 µH, COUT = 120 µF, CFF = 100 pF. Please refer to
Application Performance Curves for Bill of materials for other VOUT and FS combinations.
70
60
70
60
5VIN
50
12VIN
50
12VIN
24VIN
24VIN
40
0.001
0.01
0.1
40
0.001
1
Current (A)
VOUT = 3.3V
FS = 500 kHz
0.1
1
Current (A)
VOUT = 5.0V
Figure 1. Efficiency
C001
FS = 200 kHz
Figure 2. Efficiency
100
100
90
90
80
80
Efficiency (%)
Efficiency (%)
0.01
C001
70
60
70
60
12VIN
12VIN
50
50
24VIN
40
0.001
0.01
0.1
1
Current (A)
VOUT = 5V
24VIN
40
0.001
0.1
1
Current (A)
FS = 500 kHz
VOUT = 5V
Figure 3. Efficiency
C001
FS = 1 MHz
Figure 4. Efficiency
100
100
90
90
80
80
Efficiency (%)
Efficiency (%)
0.01
C001
70
60
70
60
12VIN
50
50
24VIN
16VIN
40
0.001
0.01
0.1
Current (A)
VOUT = 5 V
FS = 2.2 MHz
36VIN
40
0.001
1
VOUT = 12V
Figure 5. Efficiency
8
0.01
0.1
Current (A)
C001
1
C049
FS = 500 kHz
Figure 6. Efficiency
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
LM43603
www.ti.com
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
Typical Characteristics (continued)
Unless otherwise specified, VIN = 12 V, VOUT = 3.3 V, FS = 500 kHz, L = 6.8 µH, COUT = 120 µF, CFF = 100 pF. Please refer to
Application Performance Curves for Bill of materials for other VOUT and FS combinations.
3.40
5.25
5VIN
3.38
3.36
VOUT (V)
VOUT (V)
3.30
3.28
5.05
5.00
4.95
3.26
4.90
3.24
4.85
3.22
4.80
0.01
0.1
4.75
0.001
1
Current (A)
Figure 7. VOUT Regulation
VOUT (V)
VOUT (V)
24VIN
5.10
4.95
5.05
5.00
4.95
4.90
4.90
4.85
4.85
4.80
4.80
0.01
0.1
4.75
0.001
1
Current (A)
Figure 9. VOUT Regulation
5.10
12.2
5.05
12.1
VOUT (V)
12.3
5.00
4.95
11.9
11.8
4.85
11.7
4.80
11.6
11.5
0.001
1
36VIN
12.0
4.90
FS = 2.2 MHz
24VIN
12.4
5.15
Current (A)
C005
Figure 10. VOUT Regulation
16VIN
0.1
1
FS = 1 MHz
12.5
12VIN
0.01
0.1
Current (A)
VOUT = 5V
5.20
0.01
C004
FS = 500 kHz
5.25
VOUT (V)
12VIN
5.15
24VIN
5.00
VOUT = 5V
8VIN
5.20
12VIN
5.05
4.75
0.001
C003
Figure 8. VOUT Regulation
5.10
VOUT = 5V
1
FS = 200 kHz
5.25
8VIN
5.15
0.1
Current (A)
VOUT = 5V
5.20
0.01
C001
FS = 500 kHz
5.25
4.75
0.001
24VIN
5.10
3.32
VOUT = 3.3V
12VIN
5.15
24VIN
3.34
3.20
0.001
8VIN
5.20
12VIN
0.01
0.1
1
Current (A)
C006
VOUT = 12V
Figure 11. VOUT Regulation
C050
FS = 500 kHz
Figure 12. VOUT Regulation
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
9
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
www.ti.com
Typical Characteristics (continued)
Unless otherwise specified, VIN = 12 V, VOUT = 3.3 V, FS = 500 kHz, L = 6.8 µH, COUT = 120 µF, CFF = 100 pF. Please refer to
Application Performance Curves for Bill of materials for other VOUT and FS combinations.
3.5
5.4
3.4
5.2
5.0
VOUT (V)
VOUT (V)
3.3
3.2
0.1A
0.5A
1A
1.5A
2A
2.5A
3.1
3.0
3.7
3.9
4.1
4.3
4.0
5.00
4.5
VOUT = 5V
5.2
5.20
5.0
5.00
4.8
4.6
0.1A
0.5A
1A
1.5A
2A
2.5A
4.4
4.2
VIN (V)
VIN (V)
12.0
5.00
11.8
VOUT (V)
VOUT (V)
5.20
4.80
4.60
0.01A
0.1A
0.5A
1A
1.5A
2A
2.5A
VIN (V)
FS = 2.2 MHz
6.20
11.6
11.4
0.1A
0.5A
1A
1.5A
2A
2.5A
3A
11.2
11.0
6.40
10.8
12.0
12.5
13.0
13.5
VIN (V)
C007
VOUT = 12V
Figure 17. Dropout Curve
10
C007
FS = 1 MHz
Figure 16. Dropout Curve
12.2
VOUT = 5V
0.1A
0.5A
1A
1.5A
2A
2.5A
4.00
5.00 5.20 5.40 5.60 5.80 6.00 6.20 6.40 6.60 6.80 7.00
Figure 15. Dropout Curve
6.00
C007
4.60
VOUT = 5V
5.80
6.40
4.80
5.40
5.60
6.20
FS = 200 kHz
C007
4.20
6.00
4.20
FS = 500 kHz
4.40
5.80
4.40
4.0
5.00 5.20 5.40 5.60 5.80 6.00 6.20 6.40 6.60 6.80 7.00
5.40
5.60
Figure 14. Dropout Curve
5.40
VOUT (V)
VOUT (V)
Figure 13. Dropout Curve
5.20
5.40
VIN (V)
5.4
4.00
5.00
5.20
C007
FS = 500 kHz
VOUT = 5V
0.1A
0.5A
1A
1.5A
2A
2.5A
4.2
VIN (V)
VOUT = 3.3V
4.6
4.4
2.9
3.5
4.8
14.0
14.5
C007
FS = 500 kHz
Figure 18. Dropout Curve
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
LM43603
www.ti.com
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
Typical Characteristics (continued)
2.0
2.2
1.9
2.1
1.8
2.0
EN Voltage (V)
EN Voltage (V)
Unless otherwise specified, VIN = 12 V, VOUT = 3.3 V, FS = 500 kHz, L = 6.8 µH, COUT = 120 µF, CFF = 100 pF. Please refer to
Application Performance Curves for Bill of materials for other VOUT and FS combinations.
1.7
1.6
1.5
1.9
1.8
1.7
1.4
1.6
±40 ±25 ±10
5
20
35
50
65
80
95
Temperature (ƒC)
110 125
±40 ±25 ±10
5
20
35
50
65
80
95
110 125
Temperature (ƒC)
C013
Figure 19. EN Falling Threshold
C013
Figure 20. EN Rising Threshold
1.020
320
1.015
280
FB Voltage (V)
EN Hysteresis (mV)
300
260
240
1.010
1.005
220
200
1.000
±40 ±25 ±10
5
20
35
50
65
80
95
Temperature (ƒC)
110 125
±40 ±25 ±10
20
35
50
65
80
95
110 125
Temperature (ƒC)
Figure 21. EN Hysteresis
C013
Figure 22. FB Voltage vs Junction Temperature
190
90
170
80
LS RDS-ON (m)
HS RDS-ON (m)
5
C013
150
130
110
70
60
50
90
40
±40 ±25 ±10
5
20
35
50
65
Temperature (ƒC)
80
95
110 125
±40 ±25 ±10
Figure 23. High-Side FET On Resistance vs Junction
Temperature
5
20
35
50
65
80
95
110 125
Temperature (ƒC)
C013
C013
Figure 24. Low-Side FET On Resistance vs Junction
Temperature
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
11
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
www.ti.com
Typical Characteristics (continued)
6.0
3.3
5.8
3.2
LS Current Limit (A)
HS Current Limit (A)
Unless otherwise specified, VIN = 12 V, VOUT = 3.3 V, FS = 500 kHz, L = 6.8 µH, COUT = 120 µF, CFF = 100 pF. Please refer to
Application Performance Curves for Bill of materials for other VOUT and FS combinations.
5.6
5.4
3.1
3.0
5.2
2.9
5.0
2.8
±40 ±25 ±10
5
20
35
50
65
80
95
Temperature (ƒC)
110 125
±40 ±25 ±10
Figure 25. High-Side Current Limit vs Junction Temperature
50
65
80
95
110 125
C013
Figure 26. Low-Side Current Limit vs Junction Temperature
Percentage of FB Voltage (%)
Percentage of FB Voltage (%)
35
116
108
106
104
102
114
112
110
108
±40 ±25 ±10
5
20
35
50
65
80
95
Temperature (ƒC)
110 125
±40 ±25 ±10
5
20
35
50
65
80
95
Temperature (ƒC)
C013
Figure 27. PGOOD OVP Falling Threshold vs Junction
Temperature
110 125
C013
Figure 28. PGOOD OVP Rising Threshold vs Junction
Temperature
98
Percentage of FB Voltage (%)
92
Percentage of FB Voltage (%)
20
Temperature (ƒC)
110
91
90
89
88
87
86
97
96
95
94
93
92
±40 ±25 ±10
5
20
35
50
65
Temperature (ƒC)
80
95
110 125
±40 ±25 ±10
5
20
35
50
65
Temperature (ƒC)
C013
Figure 29. PGOOD UVP Falling Threshold vs Junction
Temperature
12
5
C013
80
95
110 125
C013
Figure 30. PGOOD UVP Rising Threshold vs Junction
Temperature
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
LM43603
www.ti.com
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
Typical Characteristics (continued)
Unless otherwise specified, VIN = 12 V, VOUT = 3.3 V, FS = 500 kHz, L = 6.8 µH, COUT = 120 µF, CFF = 100 pF. Please refer to
Application Performance Curves for Bill of materials for other VOUT and FS combinations.
80
Evaluation Board
70
Radiated EMI Emissions (dBµV/m)
Radiated EMI Emissions (dBµV/m)
80
EN 55022 Class B Limit
EN 55022 Class A Limit
60
50
40
30
20
10
0
EN 55022 Class B Limit
EN 55022 Class A Limit
60
50
40
30
20
10
0
0
200
400
600
800
1000
Frequency (MHz)
VOUT = 3.3 V
0
IOUT = 3 A
VOUT = 5 V
600
Conducted EMI (dBµV)
60
50
40
30
20
10
C001
IOUT = 3 A
Peak Emissions
90
70
1000
Figure 32. LM43603PWPEVM Radiated EMI Curve
Quasi Peak Limit
Average Limit
800
FS = 500 kHz
100
Peak Emissions
80
400
Frequency (MHz)
Figure 31. LM43603PWPEVM Radiated EMI Curve
90
200
C001
FS = 500 kHz
100
Conducted EMI (dBµV)
Evaluation Board
70
Quasi Peak Limit
80
Average Limit
70
60
50
40
30
20
10
0
0
0.1
1
10
Frequency (MHz)
VOUT = 3.3V
Cd = 47 µF
FS = 500 kHz
Lin = 1 µH
100
0.1
IOUT = 3 A
CIN4 = 68 µF
Figure 33. LM43603PWPEVM Conducted EMI Curve
1
10
100
Frequency (MHz)
C001
VOUT = 5V
Cd = 47 µF
FS = 500 kHz
Lin = 1 µH
C001
IOUT = 3 A
CIN4 = 68 µF
Figure 34. LM43603PWPEVM Conducted EMI Curve
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
13
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
www.ti.com
8 Detailed Description
8.1 Overview
The LM43603 SIMPLE SWITCHER® regulator is an easy to use synchronous step-down DC-DC converter that
operates from 3.5 V to 36 V supply voltage. It is capable of delivering up to 3 A DC load current with exceptional
efficiency and thermal performance in a very small solution size. An extended family is available in 0.5 A, 1 A,
and 2 A load options in pin to pin compatible packages.
The LM43603 employs fixed frequency peak current mode control with Discontinuous Conduction Mode (DCM)
and Pulse Frequency Modulation (PFM) mode at light load to achieve high efficiency across the load range. The
device is internally compensated, which reduces design time, and requires fewer external components. The
switching frequency is programmable from 200 kHz to 2.2 MHz by an external resistor RT. It is default at 500 kHz
without RT resistor. The LM43603 is also capable of synchronization to an external clock within the 200 kHz to
2.2 MHz frequency range. The wide switching frequency range allows the device to be optimized to fit small
board space at higher frequency, or high efficient power conversion at lower frequency.
Optional features are included for more comprehensive system requirements, including power-good (PGOOD)
flag, precision enable, synchronization to external clock, extendable soft-start time, and output voltage tracking.
These features provide a flexible and easy to use platform for a wide range of applications. Protection features
include over temperature shutdown, VCC under-voltage lockout (UVLO), cycle-by-cycle current limit, and shortcircuit protection with hiccup mode.
The family requires few external components and the pin arrangement was designed for simple, optimum PCB
layout. The LM43603 device is available in the HTSSOP / PWP 16 pin leaded package.
8.2 Functional Block Diagram
ENABLE
VCC
Enable
Internal
SS
ISSC
BIAS
VCC
LDO
VIN
Precision
Enable
SS/TRK
CBOOT
HS I Sense
+
EA
REF
RC
+
±
+±
TSD
UVLO
CC
PGOOD
AGND
OV/UV
Detector
FB
SW
PWM CONTROL LOGIC
PFM
Detector
PGood
Slope
Comp
Freq
Foldback
Zero
Cross
HICCUP
Detector
Oscillator
LS I Sense
FB
PGood
SYNC
14
PGND
RT
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
LM43603
www.ti.com
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
8.3 Feature Description
8.3.1 Fixed Frequency Peak Current Mode Controlled Step-Down Regulator
The following operating description of the LM43603 will refer to the Functional Block Diagram and to the
waveforms in Figure 35. The LM43603 is a step-down Buck regulator with both high-side (HS) switch and lowside (LS) switch (synchronous rectifier) integrated. The LM43603 supplies a regulated output voltage by turning
on the HS and LS NMOS switches with controlled ON time. During the HS switch ON time, the SW pin voltage
VSW swings up to approximately VIN, and the inductor current iL increases with a linear slope (VIN - VOUT) / L.
When the HS switch is turned off by the control logic, the LS switch is turned on after a anti-shoot-through dead
time. Inductor current discharges through the LS switch with a slope of -VOUT / L. The control parameter of Buck
converters are defined as Duty Cycle D = tON / TSW, where tON is the HS switch ON time and TSW is the switching
period. The regulator control loop maintains a constant output voltage by adjusting the duty cycle D. In an ideal
Buck converter, where losses are ignored, D is proportional to the output voltage and inversely proportional to
the input voltage: D = VOUT / VIN.
VSW
D = tON / TSW
SW Voltage
VIN
tOFF
tON
0
t
-VD1
Inductor Current
iL
TSW
ILPK
IOUT
ûiL
t
0
Figure 35. SW Node and Inductor Current Waveforms in Continuous Conduction Mode (CCM)
The LM43603 synchronous Buck converter employs peak current mode control topology. A voltage feedback
loop is used to get accurate DC voltage regulation by adjusting the peak current command based on voltage
offset. The peak inductor current is sensed from the HS switch and compared to the peak current to control the
ON time of the HS switch. The voltage feedback loop is internally compensated, which allows for fewer external
components, makes it easy to design, and provides stable operation with almost any combination of output
capacitors. The regulator operates with fixed switching frequency in Continuous Conduction Mode (CCM) and
Discontinuous Conduction Mode (DCM). At very light load, the LM43603 will operate in PFM to maintain high
efficiency and the switching frequency will decrease with reduced load current.
8.3.2 Light Load Operation
DCM operation is employed in the LM43603 when the inductor current valley reaches zero. The LM43603 will be
in DCM when load current is less than half of the peak-to-peak inductor current ripple in CCM. In DCM, the LS
switch is turned off when the inductor current reaches zero. Switching loss is reduced by turning off the LS FET
at zero current and the conduction loss is lowered by not allowing negative current conduction. Power conversion
efficiency is higher in DCM than CCM under the same conditions.
In DCM, the HS switch ON time will reduce with lower load current. When either the minimum HS switch ON time
(tON-MIN) or the minimum peak inductor current (IPEAK-MIN) is reached, the switching frequency will decrease to
maintain regulation. At this point, the LM43603 operates in PFM. In PFM, switching frequency is decreased by
the control loop when load current reduces to maintain output voltage regulation. Switching loss is further
reduced in PFM operation due to less frequent switching actions.
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
15
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
www.ti.com
Feature Description (continued)
In PFM operation, a small positive DC offset is required at the output voltage to activate the PFM detector. The
lower the frequency in PFM, the more DC offset is needed at VOUT. Please refer to the Typical Characteristics for
typical DC offset at very light load. If the DC offset on VOUT is not acceptable for a given application, a static load
at output is recommended to reduce or eliminate the offset. Lowering values of the feedback divider RFBT and
RFBB can also serve as a static load. In conditions with low VIN and/or high frequency, the LM43603 may not
enter PFM mode if the output voltage cannot be charged up to provide the trigger to activate the PFM detector.
Once the LM43603 is operating in PFM mode at higher VIN, it will remain in PFM operation when VIN is reduced.
Please refer to Figure 45 for a sample of PFM operation
8.3.3 Adjustable Output Voltage
The voltage regulation loop in the LM43603 regulates output voltage by maintaining the voltage on FB pin ( VFB)
to be the same as the internal REF voltage (VREF). A resistor divider pair is needed to program the ratio from
output voltage VOUT to VFB. The resistor divider is connected from the VOUT of the LM43603 to ground with the
mid-point connecting to the FB pin.
VOUT
RFBT
FB
RFBB
Figure 36. Output Voltage Setting
The voltage reference system produces a precise voltage reference over temperature. The internal REF voltage
is 1.011 V typically. To program the output voltage of the LM43603 to be a certain value VOUT, RFBB can be
calculated with a selected RFBT by
VFB
RFBB
RFBT
VOUT VFB
(1)
The choice of the RFBT depends on the application. RFBT in the range from 10 kΩ to 100 kΩ is recommended for
most applications. A lower RFBT value can be used if static loading is desired to reduce VOUT offset in PFM
operation. Lower RFBT will reduce efficiency at very light load. Less static current goes through a larger RFBT and
might be more desirable when light load efficiency is critical. But RFBT larger than 1 MΩ is not recommended
because it makes the feedback path more susceptible to noise. Larger RFBT value requires more carefully
designed feedback path on the PCB. The tolerance and temperature variation of the resistor dividers affect the
output voltage regulation. It is recommended to use divider resistors with 1% tolerance or better and temperature
coefficient of 100 ppm or lower.
If the resistor divider is not connected properly, output voltage cannot be regulated since the feedback loop is
broken. If the FB pin is shorted to ground, the output voltage will be driven close to VIN, since the regulator sees
very low voltage on the FB pin and tries to regulator it up. The load connected to the output could be damaged
under such a condition. Do not short FB pin to ground when the LM43603 is enabled. It is important to route the
feedback trace away from the noisy area of the PCB. For more layout recommendations, please refer to the
Layout section.
8.3.4 Enable (EN)
Voltage on the EN pin (VEN) controls the ON or OFF operation of the LM43603. Applying a voltage less than 0.4
V to the EN input shuts down the operation of the LM43603. In shutdown mode the quiescent current drops to
typically 1.2 µA at VIN = 12 V.
The internal LDO output voltage VCC is turned on when VEN is higher than 1.2 V. The LM43603 switching action
and output regulation are enabled when VEN is greater than 2.1 V (typical). The LM43603 supplies regulated
output voltage when enabled and output current up to 3 A.
The EN pin is an input and cannot be open circuit or floating. The simplest way to enable the operation of the
LM43603 is to connect the EN pin to VIN pins directly. This allows self-start-up of the LM43603 when VIN is
within the operation range.
16
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
LM43603
www.ti.com
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
Feature Description (continued)
Many applications will benefit from the employment of an enable divider RENT and RENB in Figure 37 to establish
a precision system UVLO level for the stage. System UVLO can be used for supplies operating from utility power
as well as battery power. It can be used for sequencing, ensuring reliable operation, or supply protection, such
as a battery discharge level. An external logic signal can also be used to drive EN input for system sequencing
and protection.
VIN
RENT
ENABLE
RENB
Figure 37. System UVLO By Enable Dividers
8.3.5 VCC, UVLO and BIAS
The LM43603 integrates an internal LDO to generate VCC for control circuitry and MOSFET drivers. The nominal
voltage for VCC is 3.28 V. The VCC pin is the output of the LDO must be properly bypassed. A high quality
ceramic capacitor with 2.2 µF to 10 µF capacitance and 6.3 V or higher rated voltage should be placed as close
as possible to VCC and grounded to the exposed PAD and ground pins. The VCC output pin should not be
loaded, left floating, or shorted to ground during operation. Shorting VCC to ground during operation may cause
damage to the LM43603.
Under voltage lockout (UVLO) prevents the LM43603 from operating until the VCC voltage exceeds 3.1 V
(typical). The VCC UVLO threshold has 520 mV of hysteresis (typically) to prevent undesired shuting down due to
temperary VIN droops.
The internal LDO has two inputs: primary from VIN and secondary from BIAS input. The BIAS input powers the
LDO when VBIAS is higher than the change-over threshold. Power loss of an LDO is calculated by ILDO * (VIN-LDO VOUT-LDO). The higher the difference between the input and output voltages of the LDO, the more power loss
occur to supply the same output current. The BIAS input is designed to reduce the difference of the input and
output voltages of the LDO to reduce power loss and improve LM43603 efficiency, especially at light load. It is
recommended to tie the BIAS pin to VOUT when VOUT ≥ 3.3 V. The BIAS pin should be grounded in applications
with VOUT less than 3.3 V. BIAS input can also come from an external voltage source, if available, to reduce
power loss. When used, a 1 µF to 10 µF high quality ceramic capacitor is recommended to bypass the BIAS pin
to ground.
8.3.6 Soft-Start and Voltage Tracking (SS/TRK)
The LM43603 has a flexible and easy to use start up rate control pin: SS/TRK. Soft-start feature is to prevent
inrush current impacting the LM43603 and its supply when power is first applied. Soft-start is achieved by slowly
ramping up the target regulation voltage when the device is first enabled or powered up.
The simplest way to use the part is to leave the SS/TRK pin open circuit or floating. The LM43603 will employ
the internal soft-start control ramp and start up to the regulated output voltage in 4.1 ms typically.
In applications with a large amount of output capacitors, or higher VOUT, or other special requirements the softstart time can be extended by connecting an external capacitor CSS from SS/TRK pin to AGND. Extended softstart time further reduces the supply current needed to charge up output capacitors and supply any output
loading. An internal current source (ISSC = 2.0 µA) charges CSS and generates a ramp from 0 V to VFB to control
the ramp-up rate of the output voltage. For a desired soft start time tSS, the capacitance for CSS can be found by
CSS ISSC u t SS
(2)
The LM43603 is capable of start up into prebiased output conditions. When the inductor current reaches zero,
the LS switch will be turned off to avoid negative current conduction. This operation mode is also called diode
emulation mode. It is built-in by the DCM operation in light loads. With a prebiased output voltage, the LM43603
will wait until the soft-start ramp allows regulation above the prebiased voltage and then follow the soft-start ramp
to the regulation level.
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
17
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
www.ti.com
Feature Description (continued)
When an external voltage ramp is applied to the SS/TRK pin, the LM43603 FB voltage follows the ramp if the
ramp magnitude is lower than the internal soft-start ramp. A resistor divider pair can be used on the external
control ramp to the SS/TRK pin to program the tracking rate of the output voltage. The final voltage seen by the
SS/TRK pin should not fall below 1.2 V to avoid abnormal operation.
EXT RAMP
RTRT
SS/TRK
RTRB
Figure 38. Soft Start Tracking External Ramp
VOUT tracked to external voltage ramps has options of ramping up slower or faster than the internal voltage ramp.
VFB always follows the lower potential of the internal voltage ramp and the voltage on the SS/TRK pin. Figure 39
shows the case when VOUT ramps slower than the internal ramp, while Figure 40 shows when VOUT ramps faster
than the internal ramp. Faster start up time may result in inductor current tripping current protection during startup. Use with special care.
Enable
Internal SS Ramp
Ext Tracking Signal to SS pin
VOUT
Figure 39. Tracking with Longer Start-up Time Than The Internal Ramp
Enable
Internal SS Ramp
Ext Tracking Signal to SS pin
VOUT
Figure 40. Tracking with Shorter Start-up Time Than The Internal Ramp
8.3.7 Switching Frequency (RT) and Synchronization (SYNC)
The switching frequency of the LM43603 can be programmed by the impedance RT from the RT pin to ground.
The frequency is inversely proportional to the RT resistance. The RT pin can be left floating and the LM43603 will
operate at 500 kHz default switching frequency. The RT pin is not designed to be shorted to ground. For a
desired frequency, typical RT resistance can be found by Equation 3. Table 1 gives typical RT values for a given
FS.
RT(kΩ) = 40200 / Freq (kHz) - 0.6
18
(3)
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
LM43603
www.ti.com
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
Feature Description (continued)
250
RT Resistance (kŸ)
200
150
100
50
0
0
500
1000
1500
2000
Switching Frequency (kHz)
2500
C008
Figure 41. RT vs Frequency Curve
Table 1. Typical Frequency Setting RT Resistance
FS (kHz)
RT (kΩ)
200
200
350
115
500
78.7
750
53.6
1000
39.2
1500
26.1
2000
19.6
2200
17.8
The LM43603 switching action can also be synchronized to an external clock from 200 kHz to 2.2 MHz. Connect
an external clock to the SYNC pin, with proper high speed termination, to avoid ringing. The SYNC pin should be
grounded if not used.
SYNC
EXT CLOCK
RTERM
Figure 42. Frequency Synchronization
The recommendations for the external clock include : high level no lower than 2 V, low level no higher than 0.4
V, duty cycle between 10% and 90% and both positive and negative pulse width no shorter than 80 ns. When the
external clock fails at logic high or low, the LM43603 will switch at the frequency programmed by the RT resistor
after a time-out period. It is recommended to connect a resistor RT to the RT pin such that the internal oscillator
frequency is the same as the target clock frequency when the LM43603 is synchronized to an external clock.
This allows the regulator to continue operating at approximately the same switching frequency if the external
clock fails.
The choice of switching frequency is usually a compromise between conversion efficiency and the size of the
circuit. Lower switching frequency implies reduced switching losses (including gate charge losses, switch
transition losses, etc.) and usually results in higher overall efficiency. However, higher switching frequency allows
use of smaller LC output filters and hence a more compact design. Lower inductance also helps transient
response (higher large signal slew rate of inductor current), and reduces the DCR loss. The optimal switching
frequency is usually a trade-off in a given application and thus needs to be determined on a case-by-case basis.
It is related to the input voltage, output voltage, most frequent load current level(s), external component choices,
and circuit size requirement. The choice of switching frequency may also be limited if an operating condition
triggers TON-MIN or TOFF-MIN.
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
19
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
www.ti.com
Feature Description (continued)
8.3.8 Minimum ON-time, Minimum OFF-time and Frequency Foldback at Drop-Out Conditions
Minimum ON-time, TON-MIN, is the smallest duration of time that the HS switch can be on. TON-MIN is typically 125
ns in the LM43603. Minimum OFF-time, TOFF-MIN, is the smallest duration that the HS switch can be off. TOFF-MIN
is typically 200 ns in the LM43603.
In CCM operation, TON-MIN and TOFF-MIN limits the voltage conversion range given a selected switching frequency.
The minimum duty cycle allowed is
DMIN = TON-MIN × FS
(4)
And the maximum duty cycle allowed is
DMAX = 1 - TOFF-MIN × FS
(5)
Given fixed TON-MIN and TOFF-MIN, the higher the switching frequency the narrower the range of the allowed duty
cycle. In the LM43603, frequency foldback scheme is employed to extend the maximum duty cycle when TOFF-MIN
is reached. The switching frequency will decrease once longer duty cycle is needed under low VIN conditions.
The switching frequency can be decreased to approximately 1/10 of the programmed frequency by RT or the
synchronization clock. Such wide range of frequency foldback allows the LM43603 output voltage stay in
regulation with a much lower supply voltage VIN. This leads to a lower effective drop-out voltage. Please refer to
Typical Characteristics for more details.
Given an output voltage, the choice of the switching frequency affects the allowed input voltage range, solution
size and efficiency. The maximum operatable supply voltage can be found by
VIN-MAX = VOUT / (FS * TON-MIN )
(6)
At lower supply voltage, the switching frequency will decrease once TOFF-MIN is tripped. The minimum VIN without
frequency foldback can be approximated by
VIN-MIN = VOUT / (1 - FS * TOFF-MIN )
(7)
Taking considerations of power losses in the system with heavy load operation, VIN-MIN is higher than the result
calculated in Equation 7 . With frequency foldback, VIN-MIN is lowered by decreased FS.
Frequency (Hz)
1000000
100000
0.1A
0.5A
1A
1.5A
2A
2.5A
10000
5.00 5.20 5.40 5.60 5.80 6.00 6.20 6.40 6.60 6.80 7.00
VIN (V)
C007
Figure 43. VOUT = 5 V Fs = 500 kHz
Frequency Foldback at Dropout
8.3.9 Internal Compensation and CFF
The LM43603 is internally compensated with RC = 400 kΩ and CC = 50 pF as shown in Functional Block
Diagram. The internal compensation is designed such that the loop response is stable over the entire operating
frequency and output voltage range. Depending on the output voltage, the compensation loop phase margin can
be low with all ceramic capacitors. An external feed-forward cap CFF is recommended to be placed in parallel
with the top resistor divider RFBT for optimum transient performance.
20
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
LM43603
www.ti.com
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
Feature Description (continued)
VOUT
RFBT
CFF
FB
RFBB
Figure 44. Feed-forward Capacitor for Loop Compensation
The feed-forward capacitor CFF in parallel with RFBT places an additional zero before the cross over frequency of
the control loop to boost phase margin. The zero frequency can be found by
fZ-CFF = 1 / ( 2π × RFBT × CFF ).
(8)
An additional pole is also introduced with CFF at the frequency of
fP-CFF = 1 / ( 2π × CFF × ( RFBT // RFBB )).
(9)
The CFF should be selected such that the bandwidth of the control loop without the CFF is centered between fZ-CFF
and fP-CFF. The zero fZ-CFF adds phase boost at the crossover frequency and improves transient response. The
pole fP-CFF helps maintaining proper gain margin at frequency beyond the crossover.
Designs with different combinations of output capacitors need different CFF. Different types of capacitors have
different Equivalent Series Resistance (ESR). Ceramic capacitors have the smallest ESR and need the most
CFF. Electrolytic capacitors have much larger ESR and the ESR zero frequency
fZ-ESR = 1 / ( 2π × ESR × COUT)
(10)
would be low enough to boost the phase up around the crossover frequency. Designs using mostly electrolytic
capacitors at the output may not need any CFF.
The CFF creates a time constant with RFBT that couples in the attenuated output voltage ripple to the FB node. If
the CFF value is too large, it can couple too much ripple to the FB and affect VOUT regulation. It could also couple
too much transient voltage deviation and falsely trip PGOOD thresholds. Therefore, CFF should be calculated
based on output capacitors used in the system. At cold temperatures, the value of CFF might change based on
the tolerance of the chosen component. This may reduce its impedance and ease noise coupling on the FB
node. To avoid this, more capacitance can be added to the output or the value of CFF can be reduced. Please
refer to the Detailed Design Procedure for the calculation of CFF.
8.3.10 Bootstrap Voltage (BOOT)
The driver of the HS switch requires a bias voltage higher than VIN when the HS switch is ON. The capacitor
connected between CBOOT and SW pins works as a charge pump to boost voltage on the CBOOT pin to (VSW +
VCC). The boot diode is integrated on the LM43603 die to minimize the Bill-Of-Material (BOM). A synchronous
switch is also integrated in parallel with the boot diode to reduce voltage drop on CBOOT. A high quality ceramic
0.47 µF 6.3 V or higher capacitor is recommended for CBOOT.
8.3.11 Power Good (PGOOD)
The LM43603 has a built in power-good flag shown on PGOOD pin to indicate whether the output voltage is
within its regulation level. The PGOOD signal can be used for start-up sequencing of multiple rails or fault
protection. The PGOOD pin is an open-drain output that requires a pull-up resistor to an appropriate DC voltage.
Voltage seen by the PGOOD pin should never exceed 12 V. A resistor divider pair can be used to divide the
voltage down from a higher potential. A typical range of pull-up resistor value is 10 kΩ to 100 kΩ.
When the FB voltage is within the power-good band, +4% above and -7% below the internal reference VREF
typically, the PGOOD switch will be turned off and the PGOOD voltage will be pulled up to the voltage level
defined by the pull up resistor or divider. When the FB voltage is outside of the tolerance band, +10% above or 13% below VREF typically, the PGOOD switch will be turned on and the PGOOD pin voltage will be pulled low to
indicate power bad. Both rising and falling edges of the power-good flag have a built-in 220 µs (typical) deglitch
delay.
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
21
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
www.ti.com
Feature Description (continued)
8.3.12 Over Current and Short Circuit Protection
The LM43603 is protected from over-current conditions by cycle-by-cycle current limiting on both the peak and
valley of the inductor current. Hiccup mode will be activated if a fault condition persists to prevent over heating.
High-side MOSFET over-current protection is implemented by the nature of the Peak Current Mode control. The
HS switch current is sensed when the HS is turned on after a set blanking time. The HS switch current is
compared to the output of the Error Amplifier (EA) minus slope compensation every switching cycle. Please refer
to Functional Block Diagram for more details. The peak current of the HS switch is limited by the maximum EA
output voltage minus the slope compensation at every switching cycle. The slope compensation magnitude at the
peak current is proportional to the duty cycle.
When the LS switch is turned on, the current going through it is also sensed and monitored. The LS switch will
not be turned OFF at the end of a switching cycle if its current is above the LS current limit ILS-LIMIT. The LS
switch will be kept ON so that inductor current keeps ramping down, until the inductor current ramps below the
LS current limit. Then the LS switch will be turned OFF and the HS switch will be turned on after a dead time. If
the current of the LS switch is higher than the LS current limit for 32 consecutive cycles and the power-good flag
is low, hiccup current protection mode will be activated. In hiccup mode, the regulator will be shutdown and kept
off for 5.5 ms typically before the LM43603 tries to start again. If over-current or short-circuit fault condition still
exist, hiccup will repeat until the fault condition is removed. Hiccup mode reduces power dissipation under severe
over-current conditions, prevents over heating and potential damage to the device.
Hiccup is only activated when power-good flag is low. Under non-severe over-current conditions when VOUT has
not fallen outside of the PGOOD tolerance band, the LM43603 will reduce the switching frequency and keep the
inductor current valley clamped at the LS current limit level. This operation mode allows slight over current
operation during load transients without tripping hiccup. If the power-good flag becomes low, hiccup operation
will start after LS current limit is tripped 32 consecutive cycles.
8.3.13 Thermal Shutdown
Thermal shutdown is a built-in self protection to limit junction temperature and prevent damage due to over
heating. Thermal shutdown turns off the device when the junction temperature exceeds 160°C typically to
prevent further power dissipation and temperature rise. Junction temperature will reduce after thermal shutdown.
The LM43603 will attempt to restart when the junction temperature drops to 150°C.
8.4 Device Functional Modes
8.4.1 Shutdown Mode
The EN pin provides electrical ON and OFF control for the LM43603. When VEN is below 0.4 V, the device is in
shutdown mode. Both the internal LDO and the switching regulator are off. In shutdown mode the quiescent
current drops to 1.2 µA typically with VIN = 12 V. The LM43603 also employs under voltage lock out protection. If
VCC voltage is below the UVLO level, the output of the regulator will be turned off.
8.4.2 Stand-by Mode
The internal LDO has a lower enable threshold than the regulator. When VEN is above 1.2 V and below the
precision enable falling threshold (1.8 V typically), the internal LDO regulates the VCC voltage at 3.2 V. The
precision enable circuitry is turned on once VCC is above the UVLO threshold. The switching action and voltage
regulation are not enabled unless VEN rises above the precision enable threshold (2.1 V typically).
8.4.3 Active Mode
The LM43603 is in Active Mode when VEN is above the precision enable threshold and VCC is above its UVLO
level. The simplest way to enable the LM43603 is to connect the EN pin to VIN. This allows self start-up of the
LM43603 when the input voltage is in the operation range: 3.5 V to 36 V. Please refer to Enable (EN) and VCC,
UVLO and BIAS for details on setting these operating levels.
In Active Mode, depending on the load current, the LM43603 will be in one of four modes:
1. Continuous conduction mode (CCM) with fixed switching frequency when load current is above half of the
peak-to-peak inductor current ripple;
22
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
LM43603
www.ti.com
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
Device Functional Modes (continued)
2. Discontinuous conduction mode (DCM) with fixed switching frequency when load current is lower than half of
the peak-to-peak inductor current ripple in CCM operation;
3. Pulse Frequency Modulation (PFM) when switching frequency is decreased at very light load;
4. Fold-back mode when switching frequency is decreased to maintain output regulation at lower supply voltage
VIN.
8.4.4 CCM Mode
Continuous Conduction Mode (CCM) operation is employed in the LM43603 when the load current is higher than
half of the peak-to-peak inductor current. In CCM peration, the frequency of operation is fixed by internal
oscillator unless the the minimum HS switch ON-time (TON_MIN) or OFF-time (TOFF_MIN) is exceeded. Output
voltage ripple will be at a minimum in this mode and the maximum output current of 2 A can be supplied by the
LM43603.
8.4.5 Light Load Operation
When the load current is lower than half of the peak-to-peak inductor current in CCM, the LM43603 will operate
in Discontinuous Conduction Mode (DCM), also known as Diode Emulation Mode (DEM). In DCM operation, the
LS FET is turned off when the inductor current drops to 0 A to improve efficiency. Both switching losses and
conduction losses are reduced in DCM, comparing to forced PWM operation at light load.
At even lighter current loads, Pulse Frequency Mode (PFM) is activated to maintain high efficiency operation.
When the HS switch ON-time reduces to TON_MIN or peak inductor current reduces to its minimum IPEAK-MIN, the
switching frequency will reduce to maintain proper regulation. Efficiency is greatly improved by reducing
switching and gate drive losses.
Frequency (Hz)
1000000
100000
10000
1000
0.001
8V
12V
24V
36V
0.010
0.100
1.000
Current (A)
C007
Figure 45. VOUT = 5 V Fs = 500 kHz
Pulse Frequency Mode Operation
8.4.6 Self-Bias Mode
For highest efficiency of operation, it is recommended that the BIAS pin be connected directly to VOUT when VOUT
≥ 3.3 V. In this Self-Bias Mode of operation, the difference between the input and output voltages of the internal
LDO are reduced and therefore the total efficiency of the LM43603 is improved. These efficiency gains are more
evident during light load operation. During this mode of operation, the LM43603 operates with a minimum
quiescent current of 27 µA (typical). Please refer to VCC, UVLO and BIAS for more details.
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
23
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
www.ti.com
9 Applications and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The LM43603 is a step down DC-to-DC regulator. It is typically used to convert a higher DC voltage to a lower
DC voltage with a maximum output current of 3 A. The following design procedure can be used to select
components for the LM43603. Alternately, the WEBENCH® software may be used to generate complete designs.
When generating a design, the WEBENCH® software utilizes iterative design procedure and accesses
comprehensive databases of components. Please go to ti.com for more details.
This section presents a simplified discussion of the design process.
9.2 Typical Applications
The LM43603 only requires a few external components to convert from a wide voltage range supply to a fixed
output voltage. Figure 46 shows a basic schematic when BIAS is connected to VOUT and this is recommended for
VOUT ≥ 3.3 V. For VOUT < 3.3 V, BIAS should be connected to ground, as shown in Figure 47.
L
VIN
VIN
CIN
VOUT
SW
LM43603
ENABLE
CBOOT
COUT
CBIAS
CFF
CBOOT
BIAS
PGOOD
SS/TRK
RT
RFBT
FB
VCC
SYNC
RFBB
CVCC
AGND
PGND
C001
Figure 46. LM43603 Basic Schematic for VOUT ≥ 3.3 V, tie BIAS to VOUT
L
VIN
VIN
CIN
VOUT
SW
LM43603
CBOOT
COUT
CBOOT
ENABLE
PGOOD
BIAS
CFF
SS/TRK
RT
SYNC
AGND
RFBT
FB
VCC
CVCC
RFBB
PGND
Figure 47. LM43603 Basic Schematic for VOUT < 3.3 V, tie BIAS to ground
The LM43603 also integrates a full list of optional features to aid system design requirements such as precision
enable, VCC UVLO, programmable soft-start, output voltage tracking, programmable switching frequency, clock
synchronization and power-good indication. Each application can select the features for a more comprehensive
design. A schematic with all features utilized is shown in Figure 48.
24
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
LM43603
www.ti.com
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
Typical Applications (continued)
L
VIN
RENT
VOUT
SW
VIN
COUT
LM43603
CIN
ENABLE
RENB
RFBT
CBOOT
CBOOT
FB
VCC
CFF
RFBB
CVCC
SS/TRK
CSS
RT
BIAS
RT
CBIAS
SYNC
PGOOD
RPG
RSYNC
AGND
Tie BIAS to PGND
when VOUT < 3.3V
PGND
Figure 48. LM43603 Schematic with All Features
The external components have to fulfill the needs of the application, but also the stability criteria of the device's
control loop. The LM43603 is optimized to work within a range of external components. The LC output filter's
inductance and capacitance have to be considered in conjunction, creating a double pole, responsible for the
corner frequency of the converter. Table 2 can be used to simplify the output filter component selection.
Table 2. L, COUT and CFF Typical Values
(1)
(2)
(3)
(4)
(5)
FS (kHz)
VOUT (V)
L (µH) (1)
200
1
4.8
600
none
200
100
COUT (µF)
(2)
CFF (pF)
(3) (4)
RT (kΩ)
RFBB (kΩ)
500
1
2.2
400
none
80.6 or open
100
1000
1
1
250
none
39.2
100
2200
1
0.47
150
none
17.8
100
200
3.3
15
300
47
200
432
500
3.3
4.7
150
33
80.6 or open
432
1000
3.3
3.3
100
22
39.2
432
2200
3.3
1
50
18
17.8
432
200
5
18
200
68
200
249
500
5
6.8
120
44
80.6 or open
249
1000
5
3.3
100
33
39.2
249
2200
5
1.5
50
22
17.8
249
200
12
33
100
See note (5)
200
90.9
500
12
15
50
68
80.6 or open
90.9
1000
12
6.8
44
56
39.2
90.9
200
24
44
47
See note (5)
200
43.2
500
24
18
47
See note (5)
80.6 or open
43.2
1000
24
10
33
See note (5)
39.2
43.2
(3) (4)
Inductance value is calculated based on VIN = 12V, except for VOUT = 12 V and VOUT = 24 V, the VIN value is 24 V and 48 V
respectively
All the COUT values are after derating. Add more when using ceramics
RFBT = 0 Ω for VOUT = 1 V. RFBT = 1 MΩ for all other VOUT setting.
For designs with RFBT other than 1 MΩ, please adjust CFF such that (CFF × RFBT) is unchanged and adjust RFBB such that (RFBT / RFBB)
is unchanged.
High ESR COUT will give enough phase boost and CFF not needed.
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
25
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
www.ti.com
Typical Applications (continued)
9.2.1 Design Requirements
Detailed design procedure is described based on a design example. For this design example, use the
parameters listed in Table 3 as the input parameters.
Table 3. Design Example Parameters
DESIGN PARAMETER
VALUE
Input Voltage VIN
12 V typical, range from 3.5 V to 36 V
Output Voltage VOUT
3.3 V
Input Ripple Voltage
400 mV
Output ripple voltage
30 mV
Output Current Rating
3A
Operating Frequency
500 kHz
Soft-start time
10 ms
9.2.2 Detailed Design Procedure
9.2.2.1 Output Voltage Set-Point
The output voltage of the LM43603 device is externally adjustable using a resistor divider network. The divider
network is comprised of top feedback resistor RFBT and bottom feedback resistor RFBB. The following equation is
used to determine the output voltage of the converter:
VFB
RFBB
RFBT
VOUT VFB
(11)
Choose the value of the RFBT to be 1 MΩ to minimize quiescent current to improve light load efficiency in this
application. With the desired output voltage set to be 3.3 V and the VFB = 1.011 V, the RFBB value can then be
calculated using Equation 11. The formula yields a value of 434.78 kΩ. Choose the closest available value of 432
kΩ for the RFBB. Please refer to Adjustable Output Voltage for more details.
9.2.2.2 Switching Frequency
The default switching frequency of the LM43603 device is set at 500 kHz when RT pin is open circuit. The
switching frequency is selected to be 500 kHz in this application for one less passive components. If other
frequency is desired, use Equation 12 to calculate the required value for RT.
RT(kΩ) = 40200 / Freq (kHz) - 0.6
(12)
For 500 kHz, the calculated RT is 79.8 kΩ and standard value 80.6 kΩ can also be used to set the switching
frequency at 500 kHz.
9.2.2.3 Input Capacitors
The LM43603 device requires high frequency input decoupling capacitor(s) and a bulk input capacitor, depending
on the application. The typical recommended value for the high frequency decoupling capacitor is 4.7 µF to 10
µF. A high-quality ceramic type X5R or X7R with sufficiency voltage rating is recommended. The voltage rating
must be greater than the maximum input voltage. To compensate the derating of ceramic capactors, a voltage
rating of twice the maximum input voltage is recommended. Additionally, some bulk capacitance can be required,
especially if the LM43603 circuit is not located within approximately 5 cm from the input voltage source. This
capacitor is used to provide damping to the voltage spiking due to the lead inductance of the cable or trace. The
value for this capacitor is not critical but must be rated to handle the maximum input voltage including ripple. For
this design, a 10 µF, X7R dielectric capacitor rated for 100 V is used for the input decoupling capacitor. The
equivalent series resistance (ESR) is approximately 3 mΩ, and the current-rating is 3 A. Include a capacitor with
a value of 0.1 µF for high-frequency filtering and place it as close as possible to the device pins.
26
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
LM43603
www.ti.com
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
NOTE
DC Bias effect: High capacitance ceramic capacitors have a DC Bias effect, which will
have a strong influence on the final effective capacitance. Therefore the right capacitor
value has to be chosen carefully. Package size and voltage rating in combination with
dielectric material are responsible for differences between the rated capacitor value and
the effective capacitance.
9.2.2.4 Inductor Selection
The first criterion for selecting an output inductor is the inductance itself. In most buck converters, this value is
based on the desired peak-to-peak ripple current, ΔiL, that flows in the inductor along with the DC load current.
As with switching frequency, the selection of the inductor is a tradeoff between size and cost. Higher inductance
gives lower ripple current and hence lower output voltage ripple with the same output capacitors. Lower
inductance could result in smaller, less expensive component. An inductance that gives a ripple current of 20% to
40% of the 3 A at the typical supply voltage is a good starting point. ΔiL = (1/5 to 2/5) x IOUT. The peak-to-peak
inductor current ripple can be found by Equation 13 and the range of inductance can be found by Equation 14
with the typical input voltage used as VIN.
'iL
(VIN VOUT ) u D
L u FS
(13)
(VIN VOUT ) u D
(V VOUT ) u D
d L d IN
0.4 u FS u IL MAX
0.2 u FS u IL MAX
(14)
D is the duty cycle of the converter where in a buck converter case it can be approximated as D = VOUT / VIN,
assuming no loss power conversion. By calculating in terms of amperes, volts, and megahertz, the inductance
value will come out in micro Henries. The inductor ripple current ratio is defined by:
'iL
r
IOUT
(15)
The second criterion is inductor saturation current rating. The inductor should be rated to handle the maximum
load current plus the ripple current:
IL-PEAK = ILOAD-MAX + ΔiL
(16)
The LM43603 has both valley current limit and peak current limit. During an instantaneous short, the peak
inductor current can be high due to a momentary increase in duty cycle. The inductor current rating should be
higher than the HS current limit. It is advised to select an inductor with a larger core saturation margin and
preferably a softer roll off of the inductance value over load current.
In general, it is preferable to choose lower inductance in switching power supplies, because it usually
corresponds to faster transient response, smaller DCR, and reduced size for more compact designs. But too low
of an inductance can generate too large of an inductor current ripple such that over current protection at the full
load could be falsely triggered. It also generates more conduction loss, since the RMS current is slightly higher
relative that with lower current ripple at the same DC current. Larger inductor current ripple also implies larger
output voltage ripple with the same output capacitors. With peak current mode control, it is not recommended to
have too small of an inductor current ripple. A larger peak current ripple improves the comparator signal to noise
ratio.
Once the inductance is determined, the type of inductor must be selected. Ferrite designs have very low core
losses and are preferred at high switching frequencies, so design goals can concentrate on copper loss and
preventing saturation. Ferrite core material saturates hard, which means that inductance collapses abruptly when
the peak design current is exceeded. The ‘hard’ saturation results in an abrupt increase in inductor ripple current
and consequent output voltage ripple. Do not allow the core to saturate!
For the design example, a standard 6.8 μH inductor from Wurth Elektronik, Coilcraft, or Vishay can be used for
the 3.3 V output with plenty of current rating margin.
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
27
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
www.ti.com
9.2.2.5 Output Capacitor Selection
The device is designed to be used with a wide variety of LC filters. It is generally desired to use as little output
capacitance as possible to keep cost and size down. The output capacitor (s), COUT, should be chosen with
care since it directly affects the steady state output voltage ripple, loop stability and the voltage over/undershoot
during load current transients.
The output voltage ripple is essentially composed of two parts. One is caused by the inductor current ripple going
through the Equivalent Series Resistance (ESR) of the output capacitors:
ΔVOUT-ESR =ΔiL×ESR
(17)
The other is caused by the inductor current ripple charging and discharging the output capacitors:
ΔVOUT-C =ΔiL/ ( 8 × FS × COUT )
(18)
The two components in the voltage ripple are not in phase, so the actual peak-to-peak ripple is smaller than the
sum of the two peaks.
Output capacitance is usually limited by transient performance specifications if the system requires tight voltage
regulation with presence of large current steps and fast slew rates. When a fast large load transient happens,
output capacitors provide the required charge before the inductor current can slew to the appropriate level. The
initial output voltage step is equal to the load current step multiplied by the ESR. VOUT continues to droop until
the control loop response increases or decreases the inductor current to supply the load. To maintain a small
over- or undershoot during a transient, small ESR and large capacitance are desired. But these also come with
higher cost and size. Thus, the motivation is to seek a fast control loop response to reduce the output voltage
deviation.
For a given input and output requirement, the following inequality gives an approximation for an absolute
minimum output cap required:
COUT !
ª§ r 2
º
·
1
u «¨ u (1 Dc) ¸ Dc u (1 r) »
¨
¸
(FS u r u 'VOUT / IOUT ) «¬© 12
»¼
¹
(19)
Along with this for the same requirement, the max ESR should be calculated as per the following inequality
ESR Dc
1
u ( 0.5)
FS u COUT r
(20)
where
r = Ripple ratio of the inductor ripple current (ΔIL / IOUT)
ΔVOUT = Target output voltage undershoot
D’ = 1 – Duty cycle
FS = Switching Frequency
IOUT = Load Current
A general guide line for COUT range is that COUT should be larger than the minimum required output capacitance
calculated by Equation 19, and smaller than 10 times the minimum required output capacitance or 1 mF. In
applications with VOUT less than 3.3 V, it is critical that low ESR output capacitors are selected. This will limit
potential output voltage overshoots as the input voltage falls below the device normal operating range. To
optimize the transient behavior a feed-forward capacitor could be added in parallel with the upper feedback
resistor. For this design example, three 47 µF,10 V, X7R ceramic capacitors are used in parallel.
9.2.2.6 Feed-Forward Capacitor
The LM43603 is internally compensated and the internal R-C values are 400 kΩ and 50 pF respectively.
Depending on the VOUT and frequency FS, if the output capacitor COUT is dominated by low ESR (ceramic types)
capacitors, it could result in low phase margin. To improve the phase boost an external feedforward capacitor
CFF can be added in parallel with RFBT. CFF is chosen such that phase margin is boosted at the crossover
frequency without CFF. A simple estimation for the crossover frequency without CFF (fx) is shown in Equation 21,
assuming COUT has very small ESR.
28
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
LM43603
www.ti.com
fx
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
5.3
VOUT u COUT
(21)
The following equation for CFF was tested:
CFF
1
1
u
2Sfx
RFBT u (RFBT / /RFBB )
(22)
This equation indicates that the crossover frequency is geometrically centered on the zero and pole frequencies
caused by the CFF capacitor.
For designs with higher ESR, CFF is not neeed when COUT has very high ESR and CFF calculated from
Equation 22 should be reduced with medium ESR. Table 2 can be used as a quick starting point.
For the application in this design example, a 47 pF COG capacitor is selected.
9.2.2.7 Bootstrap Capacitors
Every LM43603 design requires a bootstrap capacitor, CBOOT. The recommended bootstrap capacitor is 0.47 μF
and rated at 6.3 V or higher. The bootstrap capacitor is located between the SW pin and the CBOOT pin. The
bootstrap capacitor must be a high-quality ceramic type with X7R or X5R grade dielectric for temperature
stability.
9.2.2.8 VCC Capacitor
The VCC pin is the output of an internal LDO for LM43603. The input for this LDO comes from either VIN or
BIAS (please refer to Functional Block Diagram for LM43603). To insure stability of the part, place a minimum of
2.2 µF, 10 V capacitor for this pin to ground.
9.2.2.9 BIAS Capacitors
For an output voltage of 3.3 V and greater, the BIAS pin can be connected to the output in order to increase light
load efficiency. This pin is an input for the VCC LDO. When BIAS is not connected, the input for the VCC LDO
will be internally connected into VIN. Since this is an LDO, the voltage differences between the input and output
will affect the efficiency of the LDO. If necessary, a capacitor with a value of 1 μF can be added close to the
BIAS pin as an input capacitor for the LDO.
9.2.2.10 Soft-Start Capacitors
The user can left the SS/TRK pin floating and the LM43603 will implement a soft start time of 4.1 ms typically. In
order to use an external soft start capacitor, the capacitor should be sized such that the soft start time will be
longer than 4.1 ms. Use the following equation in order to calculate the soft start capacitor value:
CSS ISSC u t SS
(23)
Where,
CSS = Soft start capacitor value (µF)
ISS = Soft start charging current (µA)
tSS = Desired soft start time (s)
For the desired soft start time of 10 ms and soft start charging current of 2.0 µA, the equation above yield a soft
start capacitor value of 0.020 µF.
9.2.2.11 Under Voltage Lockout Set-Point
The undervoltage lockout (UVLO) is adjusted using the external voltage divider network of RENT and RENB. RENT
is connected between the VIN pin and the EN pin of the LM43603. RENB is connected between the EN pin and
the GND pin. The UVLO has two thresholds, one for power up when the input voltage is rising and one for power
down or brown outs when the input voltage is falling. The following equation can be used to determine the VIN
UVLO level.
VIN-UVLO-RISING = VENH × (RENB + RENT) / RENB
(24)
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
29
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
www.ti.com
The EN rising threshold (VENH) for LM43603 is set to be 2.2 V (typical). Choose the value of RENB to be 1 MΩ to
minimize input current from the supply. If the desired VIN UVLO level is at 5.0 V, then the value of RENT can be
calculated using the equation below:
RENT = (VIN-UVLO-RISING / VENH -1) × RENB
(25)
The above equation yields a value of 1.27 MΩ. The resulting falling UVLO threshold, equals 4.3 V, can be
calculated by below equation, where EN falling threshold (VENL) is 1.9 V (typical).
VIN-UVLO-FALLING = VENL × (RENB + RENT) / RENB
(26)
9.2.2.12 PGOOD
A typical pull-up resistor value is 10 kΩ to 100 kΩ from PGOOD pin to a voltage no higher than 12 V. If it is
desired to pull up PGOOD pin to a voltage higher than 12 V, a resistor can be added from PGOOD pin to ground
to divide the voltage seen by the PGOOD pin to a value no higher than 12 V.
30
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
LM43603
www.ti.com
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
9.2.3 Application Performance Curves
Unless otherwise specified, VIN = 12 V, VOUT = 3.3 V, FS = 500 kHz. Please refer to Application Performance Curves for Bill of
materials for each VOUT and FS combination.
100
2.2µH
VIN
VIN
90
1VOUT
SW
4.7
µF
LM43603
0.47µF
CBOOT
FB
SS/TRK
VCC
400µF
1MŸ
Open
Open
2.2µF
RT
SYNC
AGND
80
Efficiency (%)
ENABLE
70
60
3.5VIN
BIAS
PGOOD
50
5VIN
PGND
12VIN
40
0.001
0.01
0.1
VOUT = 1 V
1
Current (A)
C001
FS = 500 kHz
VOUT = 1 V
Figure 49. BOM for VOUT= 1V FS = 500kHz
C001
Fs = 500 kHz
Figure 50. Efficiency
1000000
1.050
3.5VIN
1.040
5VIN
12VIN
Frequency (Hz)
VOUT (V)
1.030
1.020
1.010
1.000
100000
10000
3.5VIN
5VIN
8VIN
12VIN
0.990
0.980
0.001
0.01
0.1
Current (A)
VOUT = 1 V
1000
0.001
1
0.010
0.100
1.000
Current (A)
C001
FS = 500 kHz
VOUT = 1 V
Figure 51. Output Voltage Regulation
C007
FS = 500 kHz
Figure 52. Frequency vs Load
3.5
3.0
IOUT (500 mA/DIV)
Curremt (A)
2.5
VOUT (50 mV/DIV)
2.0
1.5
12VIN
1.0
18VIN
0.5
24VIN
0.0
65
Time (100µs/DIV)
75
VIN = 12 V
VOUT = 1 V
85
95
105
115
Ambient Temperature (ƒC)
C001
VOUT = 1 V
Figure 53. Load Transient 0.1A to 1A
FS = 500 kHz
C050
θJA = 20°C/W
Figure 54. Derating Curve
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
125
31
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
www.ti.com
Unless otherwise specified, VIN = 12 V, VOUT = 3.3 V, FS = 500 kHz. Please refer to Application Performance Curves for Bill of
materials for each VOUT and FS combination.
100
90
6.8µH
VIN
3.3VOUT
SW
4.7
µF
LM43603
CBOOT
FB
ENABLE
0.47µF
120µF
VCC
SS/TRK
1MŸ
100pF
432kŸ
2.2µF
Efficiency (%)
VIN
RT
80
70
60
5VIN
BIAS
SYNC
50
PGOOD
AGND
12VIN
24VIN
PGND
40
0
0.5
1
VOUT = 3.3 V
FS = 500 kHz
VOUT = 3.3 V
Figure 55. BOM for VOUT = 3.3 V FS = 500 kHz
2
2.5
100
100
90
90
80
80
70
60
FS = 500 kHz
70
60
5VIN
50
5VIN
50
12VIN
12VIN
24VIN
40
0.001
0.01
0.1
VOUT = 3.3 V
24VIN
40
0.001
1
Current (A)
FS = 500 kHz
VOUT = 3.3 V
3
12VIN
C001
FS = 500 kHz
5VIN
12VIN
2.5
24VIN
Power Dissipation (W)
Power Dissipation (W)
1
Figure 58. Efficiency at 85ºC Ambient Temperature
2
1.5
1
0.5
24VIN
2
1.5
1
0.5
0
0
0
0.5
1
1.5
2
2.5
Current (A)
VOUT = 3.3 V
3
0
0.5
FS = 500 kHz
1
1.5
Current (A)
C001
VOUT = 3.3 V
Figure 59. Power Loss at Room Temperature
32
0.1
Current (A)
5VIN
2.5
0.01
C001
Figure 57. Efficiency at Room Temperature
3
3
C001
Figure 56. Efficiency at Room Temperature
Efficiency (%)
Efficiency (%)
1.5
Current (A)
C001
2
2.5
3
C001
FS = 500 kHz
Figure 60. Power Loss at 85°C Ambient Temperature
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
LM43603
www.ti.com
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
Unless otherwise specified, VIN = 12 V, VOUT = 3.3 V, FS = 500 kHz. Please refer to Application Performance Curves for Bill of
materials for each VOUT and FS combination.
1000000
3.5
FREQUENCY (Hz)
3.4
VOUT (V)
3.3
3.2
0.1A
0.5A
1A
1.5A
2A
2.5A
3.1
3.0
100000
0.1A
0.5A
1A
1.5A
2A
2.5A
10000
1000
2.9
3.5
3.7
3.9
4.1
4.3
VIN (V)
VOUT = 3.3 V
3.5
4.5
3.7
3.9
4.1
FS = 500 kHz
VOUT = 3.3 V
Figure 61. Dropout Curve
4.5
C007
FS = 500 kHz
Figure 62. Frequency vs VIN
1000000
3.40
5VIN
3.38
12VIN
3.36
24VIN
3.34
100000
VOUT (V)
FREQUENCY (Hz)
4.3
VIN (V)
C007
5VIN
8VIN
12VIN
24VIN
10000
1000
0.001
0.01
0.1
VOUT = 3.3 V
3.30
3.28
3.26
3.24
3.22
3.20
0.001
1
Current (A)
3.32
0.01
0.1
1
Current (A)
C007
FS = 500 kHz
VOUT = 3.3 V
Figure 63. Frequency vs Load
C001
FS = 500 kHz
Figure 64. Output Voltage Regulation
3.5
3.0
IOUT (1A/DIV)
Curremt (A)
2.5
2.0
1.5
12VIN
1.0
VOUT (200 mV/DIV)
18VIN
0.5
24VIN
0.0
65
Time (100µs/DIV)
75
VOUT = 3.3 V
FS = 500 kHz
85
95
105
115
Ambient Temperature (ƒC)
C001
VOUT = 3.3 V
Figure 65. Load Transient 0.1A to 2A
FS = 500 kHz
C050
θJA = 20°C/W
Figure 66. Derating Curve
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
125
33
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
www.ti.com
Unless otherwise specified, VIN = 12 V, VOUT = 3.3 V, FS = 500 kHz. Please refer to Application Performance Curves for Bill of
materials for each VOUT and FS combination.
100
90
22µH
VIN
4.7
µF
5VOUT
SW
LM43603
CBOOT
FB
ENABLE
0.47µF
VCC
SS/TRK
150µF
1MŸ
100pF
249kŸ
2.2µF
Efficiency (%)
VIN
RT
200kŸ
80
70
60
12VIN
BIAS
SYNC
50
PGOOD
AGND
24VIN
PGND
40
0.001
0.01
0.1
VOUT = 5 V
FS = 200 kHz
VOUT = 5 V
Figure 67. BOM for VOUT = 5 V FS = 200 kHz
5.25
5.4
12VIN
5.15
5.2
24VIN
5.0
VOUT (V)
5.10
VOUT (V)
C001
FS = 200 kHz
Figure 68. Efficiency at Room Temperature
8VIN
5.20
1
Current (A)
C001
5.05
5.00
4.95
4.90
4.8
4.6
0.1A
0.5A
1A
1.5A
2A
2.5A
4.4
4.85
4.2
4.80
4.75
0.001
0.01
0.1
Current (A)
VOUT = 5 V
4.0
5.00
1
5.20
5.40
5.60
5.80
6.00
6.20
VIN (V)
C003
FS = 200 kHz
VOUT = 5 V
Figure 69. Output Voltage Regulation
6.40
C007
FS = 200 kHz
Figure 70. Drop-out Curve
3.5
3.0
IOUT (1A/DIV)
Curremt (A)
2.5
2.0
1.5
12VIN
18VIN
24VIN
28VIN
1.0
VOUT (200 mV/DIV)
0.5
0.0
65
Time (100µs/DIV)
75
VOUT = 5 V
FS = 200 kHz
VOUT = 5 V
Figure 71. Load Transient 0.1A to 2A
34
85
95
105
Ambient Temperature (ƒC)
C001
Submit Documentation Feedback
FS = 200 kHz
115
125
C050
θJA = 20°C/W
Figure 72. Derating Curve
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
LM43603
www.ti.com
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
Unless otherwise specified, VIN = 12 V, VOUT = 3.3 V, FS = 500 kHz. Please refer to Application Performance Curves for Bill of
materials for each VOUT and FS combination.
100
90
10µH
VIN
5VOUT
SW
4.7
µF
LM43603
CBOOT
FB
ENABLE
0.47µF
VCC
SS/TRK
100µF
1MŸ
100pF
249kŸ
2.2µF
Efficiency (%)
VIN
RT
80
70
60
12VIN
BIAS
SYNC
50
PGOOD
AGND
24VIN
PGND
40
0.001
0.01
0.1
VOUT = 5 V
FS = 500 kHz
VOUT = 5 V
Figure 73. BOM for VOUT = 5 V FS = 500 kHz
5.25
5.4
12VIN
5.15
5.2
24VIN
5.0
VOUT (V)
5.10
VOUT (V)
C001
FS = 500 kHz
Figure 74. Efficiency at Room Temperature
8VIN
5.20
1
Current (A)
C001
5.05
5.00
4.95
4.90
4.8
4.6
0.1A
0.5A
1A
1.5A
2A
2.5A
4.4
4.85
4.2
4.80
4.75
0.001
0.01
0.1
Current (A)
VOUT = 5 V
4.0
5.00 5.20 5.40 5.60 5.80 6.00 6.20 6.40 6.60 6.80 7.00
1
VIN (V)
C004
FS = 500 kHz
VOUT = 5 V
Figure 75. Output Voltage Regulation
C007
FS = 500 kHz
Figure 76. Drop-out Curve
3.5
3.0
IOUT (1A/DIV)
Curremt (A)
2.5
2.0
1.5
12VIN
18VIN
24VIN
28VIN
1.0
VOUT (200 mV/DIV)
0.5
0.0
65
Time (100µs/DIV)
75
VOUT = 5 V
FS = 500 kHz
85
95
105
115
Ambient Temperature (ƒC)
C001
VOUT = 5 V
Figure 77. Load Transient 0.1A to 2A
FS = 500 kHz
C050
θJA = 20°C/W
Figure 78. Derating Curve
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
125
35
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
www.ti.com
Unless otherwise specified, VIN = 12 V, VOUT = 3.3 V, FS = 500 kHz. Please refer to Application Performance Curves for Bill of
materials for each VOUT and FS combination.
100
90
4.7µH
VIN
SW
4.7
µF
LM43603
CBOOT
FB
ENABLE
0.47µF
68µF
VCC
SS/TRK
1MŸ
100pF
249kŸ
2.2µF
80
Efficiency (%)
VIN
5VOUT
70
60
RT
39.2kŸ
12VIN
BIAS
SYNC
50
PGOOD
AGND
24VIN
PGND
40
0.001
0.01
VOUT = 5 V
FS = 1 MHz
VOUT = 5 V
Figure 79. BOM for VOUT = 5 V FS = 1 MHz
5.25
5.20
24VIN
5.00
VOUT (V)
5.10
VOUT (V)
C001
FS = 1 MHz
5.40
12VIN
5.15
1
Figure 80. Efficiency
8VIN
5.20
0.1
Current (A)
C001
5.05
5.00
4.95
4.90
4.80
4.60
0.1A
0.5A
1A
1.5A
2A
2.5A
4.40
4.85
4.20
4.80
4.75
0.001
0.01
0.1
Current (A)
VOUT = 5 V
4.00
5.00 5.20 5.40 5.60 5.80 6.00 6.20 6.40 6.60 6.80 7.00
1
VIN (V)
C005
FS = 1 MHz
VOUT = 5 V
Figure 81. Output Voltage Regulation
C007
FS = 1 MHz
Figure 82. Drop-out Curve
3.5
3.0
IOUT (1A/DIV)
Curremt (A)
2.5
2.0
1.5
12VIN
18VIN
24VIN
28VIN
1.0
VOUT (200 mV/DIV)
0.5
0.0
65
Time (100µs/DIV)
75
VOUT = 5 V
FS = 1 MHz
VOUT = 5 V
Figure 83. Load Transient
36
85
95
105
Ambient Temperature (ƒC)
C001
FS = 1 MHz
115
125
C050
θJA = 20°C/W
Figure 84. Derating Curve
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
LM43603
www.ti.com
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
Unless otherwise specified, VIN = 12 V, VOUT = 3.3 V, FS = 500 kHz. Please refer to Application Performance Curves for Bill of
materials for each VOUT and FS combination.
100
90
2.2µH
VIN
5VOUT
SW
4.7
µF
LM43603
CBOOT
FB
ENABLE
0.47µF
68µF
VCC
SS/TRK
1MŸ
68pF
249kŸ
2.2µF
80
Efficiency (%)
VIN
70
60
RT
17.8kŸ
BIAS
SYNC
12VIN
50
PGOOD
AGND
16VIN
PGND
40
0.001
0.01
0.1
VOUT = 5 V
1
Current (A)
C001
FS = 2.2 MHz
VOUT = 5 V
C001
FS = 2.2 MHz
Figure 85. BOM for VOUT = 5 V FS = 2.2 MHz
Figure 86. Efficiency
5.25
5.40
5.20
5.20
5.15
5.00
5.05
VOUT (V)
VOUT (V)
5.10
5.00
4.95
4.90
4.80
4.60
0.01A
0.1A
0.5A
1A
1.5A
2A
2.5A
4.40
4.85
12VIN
4.80
16VIN
4.75
0.001
0.01
0.1
4.00
5.00
1
Current (A)
VOUT = 5 V
4.20
5.20
5.40
5.60
5.80
6.00
6.20
VIN (V)
C001
FS = 2.2 MHz
VOUT = 5 V
6.40
C007
FS = 2.2 MHz
Figure 87. Output Voltage Regulation
Figure 88. Drop-out Curve
3.5
3.0
IOUT (1A/DIV)
Curremt (A)
2.5
VOUT (200 mV/DIV)
2.0
1.5
1.0
0.5
12VIN
0.0
65
Time (100µs/DIV)
75
VOUT = 5 V
FS = 2.2 MHz
85
95
105
115
Ambient Temperature (ƒC)
C001
VOUT = 5 V
Figure 89. Load Transient
FS = 2.2 MHz
125
C050
θJA = 20°C/W
Figure 90. Derating Curve
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
37
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
www.ti.com
Unless otherwise specified, VIN = 12 V, VOUT = 3.3 V, FS = 500 kHz. Please refer to Application Performance Curves for Bill of
materials for each VOUT and FS combination.
100
90
16µH
VIN
12VOUT
SW
4.7
µF
LM43603
CBOOT
FB
ENABLE
0.47µF
VCC
SS/TRK
68µF
1MŸ
47pF
90.9kŸ
2.2µF
80
Efficiency (%)
VIN
70
60
RT
BIAS
SYNC
50
PGOOD
AGND
24VIN
PGND
36VIN
40
0.001
0.01
0.1
Current (A)
C001
VOUT = 12 V
1
FS = 500 kHz
VOUT = 12 V
C049
FS = 500 kHz
Figure 91. BOM for VOUT = 12 V FS = 500 kHz
Figure 92. Efficiency
12.2
12.5
24VIN
12.4
12.0
36VIN
12.3
11.8
VOUT (V)
VOUT (V)
12.2
12.1
12.0
11.9
11.8
11.6
11.4
0.1A
0.5A
1A
1.5A
2A
2.5A
3A
11.2
11.7
11.0
11.6
11.5
0.001
0.01
0.1
Current (A)
VOUT = 12 V
10.8
12.0
1
12.5
13.0
13.5
14.0
VIN (V)
C050
VOUT = 24 V
FS = 500 kHz
14.5
C007
FS = 500 kHz
Figure 94. Drop-out Curve
Figure 93. Output Voltage Regulation
3.5
3.0
IOUT (1A/DIV)
Curremt (A)
2.5
2.0
1.5
24VIN
1.0
VOUT (200 mV/DIV)
28VIN
0.5
36VIN
0.0
65
Time (100µs/DIV)
75
VOUT = 24 V
FS = 500 kHz
VIN = 12 V
VOUT = 12 V
Figure 95. Load Transient 0.1A to 2A
38
85
95
105
Ambient Temperature (ƒC)
C001
Submit Documentation Feedback
FS = 500 kHz
115
125
C050
θJA = 20°C/W
Figure 96. Derating Curve
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
LM43603
www.ti.com
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
10 Power Supply Recommendations
The LM43603 is designed to operate from an input voltage supply range between 3.5 V and 36 V. This input
supply should be well regulated and able to withstand maximum input current and maintain a stable voltage. The
resistance of the input supply rail should be low enough that an input current transient does not cause a high
enough drop at the LM43603 supply voltage that can cause a false UVLO fault triggering and system reset.
If the input supply is located more than a few inches from the LM43603 additional bulk capacitance may be
required in addition to the ceramic bypass capacitors. The amount of bulk capacitance is not critical, but a 47 µF
or 100 µF electrolytic capacitor is a typical choice.
11 Layout
The performance of any switching converter depends as much upon the layout of the PCB as the component
selection. The following guidelines will help users design a PCB with the best power conversion performance,
thermal performance, and minimized generation of unwanted EMI.
11.1 Layout Guidelines
1. Place ceramic high frequency bypass CIN as close as possible to the LM43603 VIN and PGND pins.
Grounding for both the input and output capacitors should consist of localized top side planes that connect to
the PGND pins and PAD.
2. Place bypass capacitors for VCC and BIAS close to the pins and ground the bypass capacitors to device
ground.
3. Minimize trace length to the FB pin net. Both feedback resistors, RFBT and RFBB should be located close to
the FB pin. Place Cff directly in parallel with RFBT. If VOUT accuracy at the load is important, make sure VOUT
sense is made at the load. Route VOUT sense path away from noisy nodes and preferably through a layer on
the other side of a shieldig layer.
4. Use ground plane in one of the middle layers as noise shielding and heat dissipation path.
5. Have a single point ground connection to the plane. The ground connections for the feedback, soft-start, and
enable components should be routed to the ground plane. This prevents any switched or load currents from
flowing in the analog ground traces. If not properly handled, poor grounding can result in degraded load
regulation or erratic output voltage ripple behavior.
6. Make VIN, VOUT and ground bus connections as wide as possible. This reduces any voltage drops on the
input or output paths of the converter and maximizes efficiency.
7. Provide adequate device heat-sinking. Use an array of heat-sinking vias to connect the exposed pad to the
ground plane on the bottom PCB layer. If the PCB has multiple copper layers, these thermal vias can also be
connected to inner layer heat-spreading ground planes. Ensure enough copper area is used for heat-sinking
to keep the junction temperature below 125°C.
11.1.1 Compact Layout for EMI Reduction
Radiated EMI is generated by the high di/dt components in pulsing currents in switching converters. The larger
area covered by the path of a pulsing current, the more EMI is generated. The key to minimize radiated EMI is to
identify pulsing current path and minimize the area of the path. In Buck converters,the pulsing current path is
from the VIN side of the input capacitors to HS switch, to the LS switch, and then return to the ground of the input
capacitors, as shown in Figure 97.
BUCK
CONVERTER
VIN
VIN
SW
L
CIN
VOUT
COUT
PGND
High di/dt
current
PGND
Figure 97. Buck Converter High Δi/Δt Path
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
39
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
www.ti.com
Layout Guidelines (continued)
High frequency ceramic bypass capacitors at the input side provide primary path for the high di/dt components of
the pulsing current. Placing ceramic bypass capacitor(s) as close as possible to the VIN and PGND pins is the
key to EMI reduction.
The SW pin connecting to the inductor should be as short as possible, and just wide enough to carry the load
current without excessive heating. Short, thick traces or copper pours (shapes) should be used for high current
condution path to minimize parasitic resistance. The output capacitors should be place close to the VOUT end of
the inductor and closely grounded to PGND pin and exposed PAD.
The bypass capacitors on VCC and BIAS pins should be placed as close as possible to the pins respectively and
closely grounded to PGND and the exposed PAD.
11.1.2 Ground Plane and Thermal Considerations
It is recommended to use one of the middle layers as a solid ground plane. Ground plane provides shielding for
sensitive circuits and traces. It also provides a quiet reference potential for the control circuitry. The AGND and
PGND pins should be connected to the ground plane using vias right next to the bypass capacitors. PGND pins
are connected to the source of the internal LS switch. They should be connected directly to the grounds of the
input and output capacitors. The PGND net contains noise at switching frequency and may bounce due to load
variations. PGND trace, as well as PVIN and SW traces, should be constrained to one side of the ground plane.
The other side of the ground plane contains much less noise and should be used for sensitive routes.
It is recommended to provide adequate device heat sinking by utilizing the PAD of the IC as the primary thermal
path. Use a minimum 4 by 4 array of 10 mil thermal vias to connect the PAD to the system ground plane heat
sink. The vias should be evenly distributed under the PAD. Use as much copper as possible, for system ground
plane, on the top and bottom layers for the best heat dissipation. Use a four-layer board with the copper
thickness for the four layers, starting from the top of, 2 oz / 1 oz / 1 oz / 2 oz. Four layer boards with enough
copper thickness provides low current conduction impedance, proper shielding and lower thermal resistance.
The thermal characteristics of the LM43603 are specified using the parameter θJA, which characterize the
junction temperature of silicon to the abient temperature in a specific system. Although the value of θJA is
dependant on manhy variables, it still can be used to approximate the operating junction temperature of the
device. To obtain an estimate of the device junction temperature, one may use the following relationship:
TJ = PD x θJA+ TA
(27)
where
TJ = Junction temperature in °C
PD = VIN x IIN x (1 - Efficiency) - 1.1 x IOUT x DCR
DCR = Inductor DC parasitic resistance in Ω
θJA = Junction to ambient thermal resistance of the device in °C/W
TA = Ambient temperature in °C
The maximum operating junction temperature of the LM43603 is 125 °C. θJA is highly related to PCB size and
layout, as well as enviromental factors such as heat sinking and air flow. Figure 98 shows measured results of
θJA with different copper area on a 2-layer board and 4-layer board.
40
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
LM43603
www.ti.com
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
Layout Guidelines (continued)
50.0
1W @ 0fpm - 2 layer
2W @ 0fpm - 2 layer
45.0
1W @ 0fpm - 4 layer
2W @ 0fpm - 4 layer
,JA (ƒC/W)
40.0
35.0
30.0
25.0
20.0
20mm x 20mm
30mm x 30mm
40mm x 40mm
Copper Area
50mm x 50mm
C007
Figure 98. θJAvs Copper Area
2oz Copper on Outer Layers and 1oz Copper on Inner Layers
11.1.3 Feedback Resistors
To reduce noise sensitivity of the output voltage feedback path, it is important to place the resistor divider and
CFF close to the FB pin, rather than close to the load. The FB pin is the input to the error amplifier, so it is a high
impedance node and very sensitive to noise. Placing the resistor divider and CFF closer to the FB pin reduces the
trace length of FB signal and reduces noise coupling. The output node is a low impedance node, so the trace
from VOUT to the resistor divider can be long if short path is not available.
If voltage accuracy at the load is important, make sure voltage sense is made at the load. Doing so will correct
for voltage drops along the traces and provide the best output accuracy. The voltage sense trace from the load to
the feedback resistor divider should be routed away from the SW node path and the inductor to avoid
contaminating the feedback signal with switch noise, while also minimizing the trace length. This is most
important when high value resistors are used to set the output voltage. It is recommended to route the voltage
sense trace and place the resistor divider on a different layer than the inductor and SW node path, such that
there is a ground plane in between the feedback trace and inductor/SW node polygon. This provides further
shielding for the voltage feedback path from EMI noises.
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
41
LM43603
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
www.ti.com
11.2 Layout Example
TO LOAD
+
VOUT sense point
is away from
inductor and
past COUT
VOUT
VOUT distribution
point is away
from inductor
and past COUT
COUT
As much copper area as possible, for
better thermal performance
L
GND
Place
bypass caps
close to
terminals
CVCC
Ground
bypass caps
to DAP
1
SW
2
CBOOT
3
14
VIN
VCC
4
13
VIN
BIAS
5
12
EN
SYNC
6
11
SS/TRK
RT
7
10
AGND
PGOOD
8
9
Thermal Vias under DAP
PAD
(17)
CBIAS
16
PGND
15
PGND
+
CBOOT
SW
CIN
VIN
Place ceramic
bypass caps close
to VIN and PGND
terminals
RFBB
FB
RFBT
CFF
Route VOUT
sense trace
away from SW
and VIN
nodes.
Preferably
shielded in an
alternative
layer
GND Plane
As much copper area as possible, for better thermal performance
Figure 99. LM43603 Board Layout Recommendations
42
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
LM43603
www.ti.com
SNVSA09B – APRIL 2014 – REVISED SEPTEMBER 2014
12 Device and Documentation Support
12.1 Trademarks
SIMPLE SWITCHER, WEBENCH are registered trademarks of Texas Instruments.
12.2 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.3 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical packaging and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: LM43603
43
PACKAGE OPTION ADDENDUM
www.ti.com
26-Sep-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM43603PWP
ACTIVE
HTSSOP
PWP
16
90
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
LM43603
LM43603PWPR
ACTIVE
HTSSOP
PWP
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
LM43603
LM43603PWPT
ACTIVE
HTSSOP
PWP
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
LM43603
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
26-Sep-2014
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
12-May-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
LM43603PWPR
HTSSOP
PWP
16
2000
330.0
12.4
LM43603PWPT
HTSSOP
PWP
16
250
180.0
12.4
Pack Materials-Page 1
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
6.9
5.6
1.6
8.0
12.0
Q1
6.9
5.6
1.6
8.0
12.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
12-May-2015
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM43603PWPR
HTSSOP
PWP
16
2000
367.0
367.0
35.0
LM43603PWPT
HTSSOP
PWP
16
250
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated