PMK130 130W Op e n F r a me and U -C hannel P ow er Su p p lie s with PFC series 130 Watts Output Power Single Output Universal 90-264VAC Input 5VDC to 48VDC Outputs 4242VDC Input to Output Isolation Active Power Factor Correction 3” x 5” x 1.4” Model Number Output V Output I max. Ripple & Noise Efficiency(min/nom) Capacitive Load SINGLE OUTPUT PMK130S-5 (U)(-A) PMK130S-12 (U)(-A) PMK130S-15 (U)(-A) PMK130S-24 (U)(-A) PMK130S-28 (U)(-A) PMK130S-36 (U)(-A) PMK130S-48 (U)(-A) 5 VDC 12 VDC 15 VDC 24 VDC 28 VDC 36 VDC 48 VDC 22 Amps 10.8 Amps 8.7 Amps 5.4 Amps 4.6 Amps 3.6 Amps 2.7 Amps 100mV pk-pk 120mV pk-pk 120mV pk-pk 120mV pk-pk 120mV pk-pk 120mV pk-pk 120mV pk-pk 75% / 80% 80% / 82% 80% / 85% 82% / 85% 82% / 85% 82% / 85% 82% / 85% 10,000uF 26,800uF 22,000uF 28,000uF 16,800uF 1,950uF 7,800uF Note: 1. The PMK130 Series is offered in an optional U-Channel Chassis as well as with optional 3.96mm pitch 5 and 10 Pin Input and Output connectors (open frame construction and screw terminals are standard respectively). Simply add a “U” at the end of the Model Number to recieve the U-Channel configuration or a “-A” to receive the pins, or both if both are desired. For example: The Model Number “PMK130S-5U-A” represents a single output 5VDC U-Channel supply with 3.96 pitched pins (5 Input; 10 Output) . See the Mechanical Dimensions on pages 3 through 8 in this specification 2. All “U” options are not covered by UL Certification unless provided with more than 10 CFM forced air cooling applied 6-10cm above T1. 3. Derating curves acceptable up tp 40°C for UL certified products All specifications are typical at nominal input, full load, and 25°C unless otherwise noted * These are stress ratings. Exposure of the devices to any of these conditions may adversely affect long term reliability. Proper operation under conditions other than the standard operating conditions is neither warranteed nor implied. WWW.ASTRODYNETDI.COM ASTRODYNE USA: 1-800-823-8082 ASTRODYNE PACIFIC: 886-2-26983458 PMK130 130W Op e n F r a me and U -C hannel P ow er Su p p lie s with PFC INPUT SPECIFICATIONS Input Voltage Range Input Frequency Range Inrush Current, typ: Input Current Power Factor (cold start) Leakage Current ENVIRONMENTAL SPECIFICATIONS 90-264VAC (100-240VAC Nom.) 47-63 Hz Cold Start, 60A @ 230VAC Input * 2.3~0.8A (90-264VAC) PF > 0.96 @ 230VAC <3.5mA @ 264VAC, 50Hz OUTPUT SPECIFICATIONS Voltage and Current Maximum Output Power Preset Accuracy (Note 6) Line Regulation (Note 5) Load Regulation (20% to FL) Ripple/Noise (Notes 1,2,7) Turn On Hold Up Time Rise Time Short Circuit Protection Over Voltage Protection Over Current Protection Transient Response Over Shoot/Under Shoot See Selection Chart 130 Watts 1% 0.5% nom / 1% max 0.5% nom / 1% max See Selection Chart <4S, typ. 20mS, typ. 30mS, typ. Auto recovery * 130% max., Auto recovery * 150% max., Auto recovery * 10mS <10% of Nominal O/P VDC GENERAL SPECIFICATIONS Safety UL/cUL: UL-EU: CE: CB: Isolation (Note 3) Insulation Resistance EMI Efficiency series UL60950-1 2nd ed./ C22.2 60950-1 2nd ed. EN60950-1 2nd ed. EN60601-1-2 IEC60950-1 2nd ed. 4242VDC I/P - O/P * 2828 VDC I/P - GND * 707VDC O/P - GND * ≥ 20MΩ (500VDC, 1S I/P-O/P) CISPR EN55011 class B See Selection Chart Oper. Temperature (Note 4) Storage Temperature Relative Humidity EMS Harmonics: Fluctuations: ESD: RS: EFT: Surge: CS: Dips: MTBF Vibration Drop Test -10°C to +70°C (See Derate Curve) -25°C to +85°C 10 to +90%, non-cond * IEC61000-3-2 Class A IEC61000-3-3 IEC61000-4-2, 6KV Contact, 8KV Air IEC61000-4-3 FR: 80MHz-2.5GHz Field Strength: 3V/M IEC61000-4-4 2KV on AC Line IEC61000-4-5 1KV (L-L); 2KV (L, N-PE) IEC61000-4-6 3V (EMF) IEC61000-4-11 95% 250CY, 70% 25CY, 40% 5CY, 5% 0.5CY 197,000 Hrs min. MIL-HDBK-217F 4G Pk, 50~500Hz, 3 Axes, 30 min* Test Height 70cm * PHYSICAL SPECIFICATIONS Size Open Frame: U-Channel: Weight Open Frame: U-Channel: 76.2 x 127 x 35.5mm (3” x 5” x 1.4”) 127 x 80.4 x 38mm (5” x 3.17” x 1.50”) 10.25 oz (291g) 13.38 oz (380g) NOTES: 1. All measurements should be made directly at the terminals of the power supply. 2. Ripple and Noise depend upon output voltage a specified per particular model. 3. Isolation for up to 1min duration. 4. Specified for free-air convection cooling. 5. Line regulation measured from 90 - 264VAC/100VAC minimum required for full load start. 6. Preset accuracy measured at nominal load, 120VAC input. 7. O/P noise measured directly at pins/terminals @ nominal load, 0uF by pass and 47uF electrolytic, pk-pk@ 20MHz bandwidth. Special EMC Notice: The end application shall provide an earth ground connection for conducted & radiated emission performance. Astrodyne is not liable for the end application without extra earth connection to PMMK130S Open Frame Power Supply. WWW.ASTRODYNETDI.COM ASTRODYNE USA: 1-800-823-8082 ASTRODYNE PACIFIC: 886-2-26983458 . PMK130 130W Op e n F r a me and U -C hannel P ow er Su p p lie s with PFC series MECHANICAL DIMENSIONS Open Frame (PMK130S-xx) 5.00in 127mm .20in 5mm 4.55in 115.6mm .22in 5.7mm .14in 4_ 3.5mm Vo Vo 3.00in 76.2mm Vo 2.61in 66.2mm COM FG COM ACN COM ACL 1.3in 33mm .10in B1 2.5mm PMMK130S-O-TB_B1 DESCRIPTION Height 33mm Height Labeling changes DATE 2010/5/6 2012/5/2 UNIT SHEET METAL TOLERANCE (UNLESS OTHERWISE SPECIFIED) SCALE DIMENSION PIERCINGBENDING ANGULAR SIZE ±0.1 ±0.15 X<8 ±0.3° DRAWN ±0.5° ±0.1 ±0.2 8<X<25 25<X<100 100<X<300 300<X<800 WWW.ASTRODYNETDI.COM .06in 1.6mm B1 Input connector : 3P / 8.25mm pitch TERMINAL BLOCK Output connector : 6P / 8.25mm pitch TERMINAL BLOCK ±0.15 ±0.2 ±0.25 ±0.5° ±0.3 ±1° ±0.3 ±0.5 ±1.5° mm MATERIAL 1:2 PART NO. A4 Erica MODEL NO. TITLE CHECKED APPROVED ASTRODYNE USA: 1-800-823-8082 ASTRODYNE PACIFIC: 886-2-26983458 PMM 2D outli PMK130 130W Op e n F r a me and U -C hannel P ow er Su p p lie s with PFC series MECHANICAL DIMENSIONS U Bracket (PMK130S-xxU) Vo Vo Vo COM FG COM ACN COM ACL 5.00in 127mm 1.50in 38mm .22in 5.7mm 4.55in 115.6mm .51in 13mm 3.17in 80.4mm 2.24in 57mm .94in 24mm 1.58in 40.2mm 1.98in 50.2mm .47in 12mm .59in 15.1mm WWW.ASTRODYNETDI.COM ASTRODYNE USA: 1-800-823-8082 ASTRODYNE PACIFIC: 886-2-26983458 130W Op e n F r a me and U -C hannel P ow er Su p p lie s with PFC PMK130 series MECHANICAL DIMENSIONS - FAN PLACEMENT RECOMMENDATION WWW.ASTRODYNETDI.COM ASTRODYNE USA: 1-800-823-8082 ASTRODYNE PACIFIC: 886-2-26983458 PMK130 130W Op e n F r a me and U -C hannel P ow er Su p p lie s with PFC series MECHANICAL DIMENSIONS Open Frame (PMK130S-xx-A) 5.00in 127mm 4.55in 115.6mm .20in 5mm .22in 5.7mm .14in 4_ 3.5mm 3.00in 76.2mm Vo Vo Vo Vo Vo COM COM COM COM COM 2.61in 66.2mm FG ACN ACL 1.3in 33mm .10in B1 2.5mm .06in 1.6mm B1 Input connector : 5P / 3.96mm pitch MOLEX 41791-0005 Output connector : 10P / 3.96mm pitch MOLEX 41791-0010 PMMK130S-O-M_B DESCRIPTION DATE Height 33mm Height Labeling changes 2010/05/06 2012/04/20 SCALE DIMENSION PIERCINGBENDING ANGULAR SHEET ±0.1 ±0.15 X<8 ±0.3° DRAWN ±0.5° ±0.1 ±0.2 8<X<25 25<X<100 100<X<300 300<X<800 WWW.ASTRODYNETDI.COM UNIT SHEET METAL TOLERANCE (UNLESS OTHERWISE SPECIFIED) ±0.15 ±0.2 ±0.25 ±0.5° ±0.3 ±1° ±0.3 ±0.5 ±1.5° mm MATERIAL 1:2 PART NO. 1 OF 1 MODEL NO. Erica TITLE CHECKED APPROVED ASTRODYNE USA: 1-800-823-8082 ASTRODYNE PACIFIC: 886-2-26983458 P 2D o PMK130 130W Op e n F r a me and U -C hannel P ow er Su p p lie s with PFC series MECHANICAL DIMENSIONS U Bracket (PMK130S-xxU-A) Vo Vo Vo Vo Vo COM COM COM COM COM FG ACN ACL 5.00in 127mm 1.50in 38mm .22in 5.7mm 4.55in 115.6mm .51in 13mm 2.24in 57mm .94in 24mm 3.17in 80.4mm 1.58in 40.2mm 1.98in 50.2mm .47in 12mm .59in 15.1mm WWW.ASTRODYNETDI.COM ASTRODYNE USA: 1-800-823-8082 ASTRODYNE PACIFIC: 886-2-26983458 130W Op e n F r a me and U -C hannel P ow er Su p p lie s with PFC PMK130 series MECHANICAL DIMENSIONS - FAN PLACEMENT RECOMMENDATION WWW.ASTRODYNETDI.COM ASTRODYNE USA: 1-800-823-8082 ASTRODYNE PACIFIC: 886-2-26983458 130W Op e n F r a me and U -C hannel P ow er Su p p lie s with PFC PMK130 series DERATE CURVES WWW.ASTRODYNETDI.COM ASTRODYNE USA: 1-800-823-8082 ASTRODYNE PACIFIC: 886-2-26983458 130W Op e n F r a me and U -C hannel P ow er Su p p lie s with PFC PMK130 series DERATE CURVES WWW.ASTRODYNETDI.COM 3814 ASTRODYNE USA: 1-800-823-8082 ASTRODYNE PACIFIC: 886-2-26983458