PLC-OS…
PLC INTERFACE With Solid-State Relay,
Universal Version
INTERFACE
Data Sheet
103148_en_02
1
© PHOENIX CONTACT - 03/2008
Description
PLC-OS… relay modules, which can be used universally,
comprise 6.2 mm basic terminal blocks and plug-in
miniature solid-state relays with screw or spring-cage
connection.
1.1
Input Voltages From 24 V to 230 V
The PLC-OS… is available on the control side in all common
industrial voltages from 24 V to 230 V. A further advantage
is the ready-integrated input circuit. It consists of a status
indicator and polarity reversal protection function, and
ensures that the operating state is displayed clearly, also
preventing destruction of the optical electronics should the
polarity be accidentally reversed.
1.2
Plug-In Bridges Save Wiring
The PLC INTERFACE module achieves maximum
efficiency with the user-friendly FBST plug-in bridge system.
The PLC-OS… makes effective use of the bridging options
for the A1/A2 connection on the control side and for the
power supply at connection 13 on the load side. Especially
effective here are the 500 mm long color-insulated
continuous plug-in bridges that can easily be cut to the
required length and quickly inserted in the bridge shafts.
They eliminate the need for complicated and timeconsuming loop bridges.
1.3
–
–
–
–
–
–
–
–
Additional Advantages
Switching power of up to 24 V DC/3 A, depending on
the type
IP67-protected fully encapsulated optical electronics
Available with input or power solid-state relays as an
option
Integrated input circuit
Solid-state relay can be replaced using an engagement
lever
Wear-resistant switching
Resistant to vibrations and shocks
Inflammability class V0 according to UL94
Make sure you always use the latest documentation.
It can be downloaded at www.download.phoenixcontact.com.
A conversion table is available on the Internet at
www.download.phoenixcontact.com/general/7000_en_00.pdf.
This data sheet is valid for all products listed on the following page:
PLC-OS…
2
Ordering Data
PLC INTERFACE With Screw Connection
Description
Type
PLC INTERFACE With Input Solid-State Relay, Universal Version
PLC INTERFACE, comprising PLC-BSC... basic
terminal block and plug-in miniature solid-state
relay (see INTERFACE catalog), for mounting on
3. Other input voltages on request.
24 V DC PLCOSC- 24DC/48DC/100
Order No.
Pcs./Pck.
2966728
10
120 V AC/110 V DC PLCOSC-120UC/48DC/100
2966744
10
230 V AC/220 V DC1 PLCOSC-230UC/48DC/100
2966757
10
PLC INTERFACE With Power Solid-State Relay, Universal Version
PLC INTERFACE, comprising PLC-BSC.../21
basic terminal block and plug-in miniature solidstate relay (see INTERFACE catalog), for
mounting on 3. Other input voltages on
request.
1
2966634
10
120 V AC/110 V DC PLCOSC-120UC/24DC/2
24 V DC PLCOSC- 24DC/24DC/2
2966650
10
230 V AC/220 V DC1 PLCOSC-230UC/24DC/2
2966663
10
The PLC-ATP BK insulating plate must be installed for voltages greater than 250 V (L1, L2, L3) between the same terminal points on adjacent modules
(see "Accessories"). FBST 8-PLC... or FBST 500... is then used for potential bridging.
PLC INTERFACE With Spring-Cage Connection
Description
Type
PLC INTERFACE With Input Solid-State Relay, Universal Version
PLC INTERFACE, comprising PLC-BSC... basic
terminal block and plug-in miniature solid-state
relay (see INTERFACE catalog), for mounting on
3. Other input voltages on request.
24 V DC PLCOSP- 24DC/48DC/100
Order No.
Pcs./Pck.
2967549
10
120 V AC/110 V DC PLCOSP-120UC/48DC/100
2967552
10
230 V AC/220 V DC1 PLCOSP-230UC/48DC/100
2967565
10
PLC INTERFACE With Power Solid-State Relay, Universal Version
PLC INTERFACE, comprising PLC-BSC.../21
basic terminal block and plug-in miniature solidstate relay (see INTERFACE catalog), for
mounting on 3. Other input voltages on
request.
1
2967471
10
120 V AC/110 V DC PLCOSP-120UC/24DC/2
24 V DC PLCOSP- 24DC/24DC/2
2967484
10
230 V AC/220 V DC1 PLCOSP-230UC/24DC/2
2967497
10
The PLC-ATP BK insulating plate must be installed for voltages greater than 250 V (L1, L2, L3) between the same terminal points on adjacent modules
(see "Accessories"). FBST 8-PLC... or FBST 500... is then used for potential bridging.
With the 120 V and 230 V modules, an OPT-60DC/... 60 V solid-state relay is normally used due to the input circuit integrated in the basic terminal
block.
For the protection of input and output, inductive loads must be dampened with an effective protective circuit.
Accessories
Description
Type
Order No.
Pcs./Pck.
Insulating plate
PLC-ATP BK
2966841
25
The PLC-ATP BK insulating plate should be used in the following cases: always fit at the start and end of a PLC terminal strip for voltages
greater than 250 V (L1, L2, L3) between the same terminal points on adjacent modules (FBST 8-PLC... or FBST 500... can be used for
potential bridging) and for safe isolation between adjacent modules.
For additional accessories such as power terminal blocks and plug-in bridges, please refer to the INTERFACE catalog or www.phoenixcontact.com.
103148_en_02
PHOENIX CONTACT
2
PLC-OS…
3
Technical Data
Input Data
Nominal input voltage1
PLCOS...48DC/100
PLCOS...24DC/2
24 V DC
120 V AC/110 V DC
230 V AC/220 V DC
24 V DC
120 V AC/110 V DC
230 V AC/220 V DC
0.8 ... 1.2 x UN
0.8 ... 1.1 x UN
0.8 ... 1.2 x UN
0.8 ... 1.1 x UN
1 signal ("H")
0.8 x UN
0.8 x UN
0.8 x UN
0.8 x UN
0 signal ("L")
0.4 x UN
0.3 x UN
0.4 x UN
0.25 x UN
Typical input current at UN
8 mA
4 mA
9 mA
4 mA
Typical response time at UN
20 μs
6 ms
20 μs
6 ms
Typical release time at UN
300 μs
10 ms
300 μs
10 ms
Permissible range (with reference to UN)
Switching level
Transmission frequency flimit
Input circuit
1
300 Hz
10 Hz
300 Hz
10 Hz
Yellow LED,
protection
against polarity
reversal, freewheeling diode
Yellow LED, bridge
rectifier
Yellow LED,
protection
against polarity
reversal, freewheeling diode
Yellow LED, bridge
rectifier
The PLC-ATP BK insulating plate must be installed for voltages greater than 250 V (L1, L2, L3) between the same terminal points on adjacent modules
(see "Accessories"). FBST 8-PLC... or FBST 500... is then used for potential bridging.
Output Data
PLCOS...48DC/100
Maximum switching voltage
PLCOS...24DC/2
48 V DC
33 V DC
Minimum switching voltage
3 V DC
Limiting continuous current
100 mA
Maximum inrush current
3 A (see "Derating Curve")
–
Output configuration
15 A (10 ms)
2-wire floating
Output circuit
Protection against polarity reversal, surge protection
≤1V
Voltage drop at maximum limiting continuous current
≤ 200 mV
General Data
Impulse voltage withstand level
2.5 kV, 50 Hz, 1 min.
Ambient temperature range
Operation
Storage/transport
-25°C ... 60°C
-40°C ... 85°C
Nominal operating mode
100% operating factor
Inflammability class according to UL 94 (housing)
V0
Standards/specifications1
IEC 60664, IEC 60664 A, DIN VDE 0110 (basic insulation)
Pollution degree
2
Surge voltage category
III
Mounting position
Any
Mounting
Can be aligned without spacing
Conductor cross-section
Solid, with screw connection
0.14 mm2 ... 2.5 mm2 (26 - 14 AWG)
Stranded, with screw connection
0.14 mm2 ... 1.5 mm2 (26 - 14 AWG)
Solid, with spring-cage connection
0.2 mm2 ... 2.5 mm2 (24 - 14 AWG)
Stranded, with spring-cage connection
0.2 mm2 ... 1.5 mm2 (24 - 14 AWG)
Stripping length
Screw connection
10 mm
Spring-cage connection
8 mm
Dimensions (W x H x D)
6.2 mm x 94 mm x 80 mm
Housing material
Polyamide PA, green
1
The PLC-ATP BK insulating plate must be installed for safe isolation between adjacent modules (see "Accessories"). FBST 8-PLC... or FBST 500... is
then used for potential bridging.
103148_en_02
PHOENIX CONTACT
3
PLC-OS…
Tests/Approvals
c
Uu
F
CE
UL
GL
Block Diagram
5
Load current [A]
4
A2
A1
Derating Curve
3
13+
2
14
1
1)
1)
0
The input circuit
depends on the type
0
10
20
30
40
50
60
Ambient temperature [°C]
103148_en_02
PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany • Phone: +49 - 52 35 - 30 0
PHOENIX CONTACT • P.O.Box 4100 • Harrisburg • PA 17111-0100 • USA • Phone: +717-944-1300
www.phoenixcontact.com
4