LevelOne User Manual VDS-0200 / VDS-0201 Ethernet over VDSL2 Converter V1.0 FCC Certifications This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation. CE Mark Warning This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 Class A for ITE, the essential protection requirement of Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility. Company has an on-going policy of upgrading its products and it may be possible that information in this document is not up-to-date. Please check with your local distributors for the latest information. No part of this document can be copied or reproduced in any form without written consent from the company. 2 Table of Content 1. INTRODUCTIONS ................................................................................... 4 2. APPLICATION NOTES ........................................................................... 4 3. FEATURES ............................................................................................. 5 4. PACKING CONTENTS ............................................................................ 5 5. LED INDICATORS .................................................................................. 6 6. DIP SWITCHES SETTINGS .................................................................... 7 7. DATA RATES & DISTANCES .................................................................. 9 8. TECHNICAL SUPPORT ........................................................................ 10 3 1. Introductions The VDS-0200/VDS-0201, a VDSL2 (Very high-bit-rate Digital Subscriber Line) LAN converter, provides a broadband transmission up to 100/60Mbps of downstream/upstream data rate over single pair copper line for point-to-point Ethernet connectivity. With 100/60Mbps data rate, the VDSL2 converter supports transmission distance up to 300 meters, and 30/10 Mbps for 1km long range connection. Users may also select a fixed data rate or a fixed SNR margin for different copper line ranging. With plug and play features and minimum installation time, each VDSL2 converter can be configured into either CO for central side or RT for remote side by dip switch setting. The VDSL2 converter conforms to the ITU-T G.993.1 and G.993.2 to meet VDSL/VDSL2 and SG15Q4 DMT for network requirements. A pair of VDSL2 converter offers a cost effective solution for bandwidth-hungry applications such as LAN-to-LAN connectivity, Video Streaming, FTTB, and MDU/MTU over single twisted pair telephone line. 2. Application Notes VDS-0200/VDS-0201 VDS-0200/VDS-0201 100 / 60 Mbps up to 300 meters Max 2km for VDSL Link Ethernet to Ethernet Bridge Extension 4 3. Features ITU-T G.993.1, G.993.2 VDSL/VDSL2 and SG15Q4 DMT Compliance 100/60Mbps DownSream/UpStream for distance up to 300 meters Supports VDSL2 connection up to 2000 meters Support Annex A, B for internal splitter (option) Line Surge Protection RJ11 x 2 for DSL and PHONE interfaces + RJ45 x 2 for Ethernet LAN port Five LED Indicators 4 Dip Switches for Configuration Settings Trellis Coding support up to 1024 Discrete Multi-Tone (DMT) bins Auto MDIX for 10/100 BaseT Ethernet LAN Ports Low-Latency for Video/Voice/Data applications Selectable Fast and Interleaved modes Fast mode guarantees a minimum end to end latency less than 1 ms. Interleaved mode provides impulse noises protection for any impulse noise with a duration less than 250 us. Interleaved mode has a maximum end to end latency of 10 ms. Interleaved mode is the default mode. Selectable fixed data rate and fixed SNR margin User may select fixed SNR margin (9 dB) or fixed target data rate. When fixed SNR margin is selected, the systems will maintain the SNR margin at 9 dB across all available loop length. When fixed target data rate is selected, the system will lock the data rate at 50/20Mbps whenever the calculated SNR margin is higher than 9 dB. This will result in the best system stability and is the default mode. 4. Packing Contents Inside the package you should find: VDSL2 Converter Power Adaptor (5VDC/2A or 5VDC/1A) User’s Manual CD Telephone line Please check if the packing is damaged or any component is missing. If so, please contact your distributor. 5 5. LED Indicators On the front panel of VDS-0200/VDS-0201, there are 5 LED indicators as the following VDS-0200 Front Panel VDS-0201 Front Panel VDS-0200/VDS-0201 Rear Panel POWER Green On Indicates power is on and normal Green On Indicates Ethernet LAN1 port is in connection Flashing Indicates Ethernet LAN1 data activities Green On Indicates Ethernet LAN1 port is in connection Flashing Indicates Ethernet LAN1 data activities Green On Indicates VDSL2 is in connection Flashing Indicates VDSL2 is in line handshaking Green On Indicates converter is set as Slave (VTU-R) mode OFF Indicates converter is set as Master (VTU-C) mode LAN1 LAN2 DSL M/S 6 6. Dip Switches Settings Pin 1: Pin 1 Pin 2 Pin 3 Pin 4 VTU-C/R Mode Rate Limit SNR OFF VTU-C Interleaved 50/20 Mbps 9dB ON VTU-R Fast Full Rate 6dB VTU-C/R Switch VTU-C: The converter will act as at the Central Office (CO) side. VTU-R: The converter will act as at the Customer Premise Equipment (CPE) or Remote side. Pin 2: Mode for impulse noise protection Interleave mode: Protection for up to 250ms impulse noises with latency less than 6 ms. Fast mode: Direct data transmission with latency less than 1ms. 7 Pin 3: Rate limit control 50/20 Mbps: Line rate limited to 50/20 Mbps. Full Rate: Provides up to 100Mbps/60Mbps line rate in short line. Pin 4: Signal to Noise Ratio (SNR) 9dB: Higher SNR margin (9dB) will result in less error with more stable VDSL2 link. 6dB: Original and Normal channel noise protection with 6 dB SNR. 8 7. Data Rates & Distances Performance in AWG 26 Line at 6dB with full rate Down Stream Data Rate (Mbps) Up Stream Data Rate (Mbps) Distance (feet) 100 60 500 98 53 1000 90 44 1250 80 36 1500 70 27 1750 60 18 2000 48 11 2500 39 8 3000 35 3.5 3500 28 0.3 4000 9 8. Technical Support Thank you for selecting LevelOne products. LeveOne’s website contains the latest user documentation and soft-ware updates for LevelOne products. Please contact LevelOne Technical Support through our website. World Wide Web http://www.level1.com 10